Trouble with linemask-DIO assigning on Port WriteVi

"I am using LabView 5.1 and a datacard AT-Mio-16E-10 with Windows NT. Why does the linemask number on Port WriteVi don´t change the same port line?(port is const., digital channel,too) If I measure at Dio 1 and the linemask is 1, it is not changing the Dio 1, when I change the pattern. But if the linemasknumber at 2 or 3 , the Dio 1 changes in the right way.
Thanks for any reply.
Attachments:
Portwrite2.vi ‏29 KB

The line mask (in binary: bit set to 1 ) affects the corresponding line.
line masks 2 (0000 0010) or 3 (0000 0011) sets bit 1 to 1 affecting DIO 1
see the modified vi to set the line mask for a particular line number
Attachments:
Modified)Portwrite2.vi ‏37 KB

Similar Messages

Trouble with SF 300-24P 24-Port 10/100 PoE

Good day.
I connect to switch Access Point, configure port on switch which vlan work on this port. But after reboot AP my config for this port delete and have other config where vlan 1 untagged, and allow all other vlan. But in my cinfig allow 3vlan: untagged 100, and tagged 113, 999.
How to solve this problem?

hi Igor, you need to save the running config to the start up config, otherwise a reboot will drop any changes made to the switch.
When you make a change to the switch, on the top right of your browser there is a blinking button to save, click this and save the run config to start up.
-Tom
Please mark answered for helpful posts

Trouble With Port Mirroring (SG200-08)

Trouble with port mirroring.
Even though both Tx and Rx is specified, only getting half the conversation. Ping reply only for instance. And when pinging from other locations no traffic at all.
Please help
SG200-008
FW Version: 1.0.2.0
Boot Version D.3.1
Thanks

I also have problem with the mirroring of port on my SG200-08. The firmware is 1.0.6.2.
I mirror the port g1, to which my router to the Internet is connected, to the port g2 to be able to see the traffic with a Centos system running Bandwidthd connected to the port g2. The problem is that I only see the traffic coming in (downloads from the Internet) and not the traffic comming out (uploads to the Internet).
When looking at the SG 200-08 on the web interface at "Status and Statistics/Interface" and looking at the port g2, I see values for the "Transmit Statistics", but all the values are at 0 for the "Received Statisticsc" (see the attached file)
I confirmed that in "Administration/Diagnostic/Port Mirroring" is set up both Tx and Rx (it does not work either if I have Tx or Rx alone: I do not see the uploda traffic to the Internet). See the attached file.
This is very annoying as I purchased this SG 200-08 especially for this and it does not do the job porperly.
Does anybody knows a solution to this?

Trouble with bridge mode and port forwarding

I have a Westell Model 6100F DSL modem in bridge mode into my network and I'm having trouble forwarding ports. Is there any general guidance available to do this. I have set many of my friends networks up to allow port forwarding but all have been on other service providers, mainly cable. (my experience) My network is the only one I have had trouble with.
Basically, my question is, while in bridge mode, does the modem forward all incoming traffic to my NAT router or do I need to apply special port forwarding settings in the modem to allow this?
If bridge mode is the reason I cannot forward the ports, can someone explain how to set the WEstell 6100F back to factory defaults so I can start over.
Any other suggestions?
Thanks in advance.
Paul

If bridge mode is set up correctly, your router should be holding the Public IP address (basically not something that is a 192.168 address) as shown at http://www.whatismyip.com/ and compared against what IP your router has.
If your router has the public IP, all problems lie with either your router or your PC's firewall and configuration. I'd check out portforward.com for some guides on forwarding ports for your router or poarticular application if you need some additional help.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Trouble with all 3 USB Ports: HP Pavilion 14-v062us Notebook PC

I was recently playing a game on my computer with a mouse controlled by a USB drive. A little bit into the game, the mouse disconnected for no known reason. I have been playing this game about six months now, and have never had this problem in the past. I relocated the drive to the other two ports, but the device was not recognized in any of the ports. I plugged in another device controlled by a USB drive and got the same results. I have uninstalled the USB Composite Device and USB Root Hubs then restarted my computer to no success. Any help towards identifying and solving the problem is greatly appreciated!

Hi there @D3rr1ck,
Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel.
I understand that you are having problems with all of the USB ports on your notebook. I am happy to help with this.
Take a look through the following and try the sections that are applicable.
HP PCs - Troubleshooting USB connections (Windows 8)
Normally the USB driver is a part of the chipset drivers for a board, so you can also try updating that, which you can find on this page: HP Pavilion 14-v062us Notebook PC (ENERGY STAR) - Software and Drivers
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Trouble with 3 ATV to connect to iTunes in one WiFi / LAN

Hi community,
I've trouble with my ATVs in my network. I have 1 3Gen. ATV connected via LAN to iTunes on iMac and 2 2Gen. ATVs via WiFi. The problem I am facing is, if I am connected with two of them to my iTunes Library the third can't even the others ( which have been conneted) are off. If I restart iTunes, I can connect again two of them and the third (doesn't matter which one) cannot. So I can circle arround which one gets connected but it is not very satisfying.
My network is setup on two Airport express and a TC 2Gen to cover the whole house. As I stated above, the ATV 3Gen is connected via Lan, and the other two via WLAN?
Any idea what I've made wrong, or what to do to find the problem?
Thanks in advance

Until the MacBook Air was released and supported in 10.5, the Mac did not consider USB to be a valid Networking Protocol. So set the Mac with USB solutions aside.
To connect computer-to-computer, you typically need to be using an Ethernet crossover cable. Assigning the same address to two Ethernet devices is never the solution -- it gives a Network Conflict, just as you said.
If your Windows box has some mechanism for Sharing its WiFi connection over Ethernet, you would have to follow its rules. Whether that means Manually assigning an Ethernet Address in the same range or the PC will provide the Address, I do not know.
Best success may be running an Ethernet cable to your Wired/Wireless Base Station, or using a "gaming adapter" (Ethernet-to-Wireless no drivers required) connected to the Mac's Ethernet port to give it WiFi access. What is your Base Station {Cable, DSL, FIOS, Other} ? Ethernet cables can be up to 100 meters (an American Football Field). Often the Base Station can be moved closer for more convenience.

I have been having a lot of trouble with the latest itunes update and my ipod classic 80Gb i.e. being unable to sync songs, but now i have no files at all on my ipod, it is completely blank when i view it from my computer. I need help, please, anybody.

As it says above, i have been having a lot f trouble with my ipod classic and the latest itunes update, i was unable to sync songs or anything to it and have tried every conceivable 'fix' i could find. i have run an itunes diagnostic and the results are posted below. a major problem is that when i try and view my ipod through my computer it displays nothing at all on the ipod, no files or anything, this may be the problem but i have no idea how it has happened or how i could resolve it.
This ipod holds huge sentimental value and i am loathe to buy a new one! If anybody can help it is greatly appreciated, than kyou in advanced.
Microsoft Windows 7 x64 Home Premium Edition Service Pack 1 (Build 7601)
ASUSTeK Computer Inc. K50IJ
iTunes 11.1.5.5
QuickTime not available
FairPlay 2.5.16
Apple Application Support 3.0.1
iPod Updater Library 11.1f5
CD Driver 2.2.3.0
CD Driver DLL 2.1.3.1
Apple Mobile Device 7.1.1.3
Apple Mobile Device Driver 1.64.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 0038B8600B98D1E0
Current user is not an administrator.
The current local date and time is 2014-03-21 16:52:39.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is supported.
Video Display Information
Intel Corporation, Mobile Intel(R) 4 Series Express Chipset Family
Intel Corporation, Mobile Intel(R) 4 Series Express Chipset Family
**** External Plug-ins Information ****
No external plug-ins installed.
Genius ID: 2fd81a1f13cf3ff25a8b4f0e8e725116
**** Device Connectivity Tests ****
iPodService 11.1.5.5 (x64) is currently running.
iTunesHelper 11.1.5.5 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Intel(R) ICH9 Family USB Universal Host Controller - 2934. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2935. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2936. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2937. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2938. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2939. Device is working properly.
Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293A. Device is working properly.
Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293C. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.

Here is what worked for me:
My usb hub, being usb2, was too fast. I moved the wire to a usb port directory on my pc. That is a usb1 port which is slow enough to run your snyc.

Trouble with Toshiba built-in webcam: "unable to enumerate USB device"

I am running archlinux on a Toshiba Satellite L70-B-12H laptop, and having troubles with the Webcam. *Once in a while*, everything goes well and I get
# lsusb
Bus 004 Device 002: ID 8087:8000 Intel Corp.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 004: ID 04f2:b448 Chicony Electronics Co., Ltd
Bus 003 Device 003: ID 8087:07dc Intel Corp.
Bus 003 Device 002: ID 8087:8008 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
# dmesg
[ 3433.456115] usb 3-1.3: new high-speed USB device number 4 using ehci-pci
[ 3433.781119] media: Linux media interface: v0.10
[ 3433.809842] Linux video capture interface: v2.00
[ 3433.826889] uvcvideo: Found UVC 1.00 device TOSHIBA Web Camera - HD (04f2:b448)
[ 3433.835893] input: TOSHIBA Web Camera - HD as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.3/3-1.3:1.0/input/input15
[ 3433.835976] usbcore: registered new interface driver uvcvideo
[ 3433.835977] USB Video Class driver (1.1.1)
Unfortunately, *most of the time* the camera seems invisible to my system, and I get
# lsusb
Bus 004 Device 002: ID 8087:8000 Intel Corp.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 8087:07dc Intel Corp.
Bus 003 Device 002: ID 8087:8008 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
(note the missing "04f2:b448 Chicony Electronics Co., Ltd" device), and
# dmesg
[ 480.104252] usb 3-1.3: new full-speed USB device number 4 using ehci-pci
[ 480.171097] usb 3-1.3: device descriptor read/64, error -32
[ 480.341235] usb 3-1.3: device descriptor read/64, error -32
[ 480.511375] usb 3-1.3: new full-speed USB device number 5 using ehci-pci
[ 480.578007] usb 3-1.3: device descriptor read/64, error -32
[ 480.748151] usb 3-1.3: device descriptor read/64, error -32
[ 480.918282] usb 3-1.3: new full-speed USB device number 6 using ehci-pci
[ 481.325196] usb 3-1.3: device not accepting address 6, error -32
[ 481.392091] usb 3-1.3: new full-speed USB device number 7 using ehci-pci
[ 481.798926] usb 3-1.3: device not accepting address 7, error -32
[ 481.799166] hub 3-1:1.0: unable to enumerate USB device on port 3
Searching on the web, most results I found lead to this page, where it is said that the problem is due to badly tuned overcurrent protection, and advocated that unplugging and switching off the computer for a little while gets things back into normal. This does not really work for me; the problem seems to occur more randomly, unfortunately with high probability (my camera is available after less than one boot out of ten).
I tried to ensure that the ehci-hcd module is loaded at boot with the ignore-oc option (with a file in /etc/module-load.d/), to no avail.
I also wrote a script which alternatively removes and reloads the ehci-pci driver until my device is found in lsusb. It is sometimes helpful, but usually not. And even when my device is found that way, it can only be used for a while before disappearing again.
Anyway, such a hack is unacceptable... So, my questions are:
is it indeed related to overcurrent protection ?
is there anything else I can try ?
should I file somewhere an other of the numerous bug reports about "unable to enumerate USB device" already existing ?
If of any importance, I am running linux 3.15.7, because at the time I installed my system, I couldn't get the hybrid graphic card Intel/AMD working under 3.16.
Last edited by $nake (2014-10-18 16:29:06)

uname -a
Linux libra 3.9.4-1-ARCH #1 SMP PREEMPT Sat May 25 16:14:55 CEST 2013 x86_64 GNU/Linux
pacman -Qi linux
Name : linux
Version : 3.9.4-1
Description : The linux kernel and modules
Architecture : x86_64
URL : http://www.kernel.org/
Licences : GPL2
Groups : base
Provides : kernel26=3.9.4
Depends On : coreutils linux-firmware kmod mkinitcpio>=0.7
Optional Deps : crda: to set the correct wireless channels of your country
Required By : nvidia
Optional For : None
Conflicts With : kernel26
Replaces : kernel26
Installed Size : 65562.00 KiB
Packager : Tobias Powalowski <[email protected]>
Build Date : Sat 25 May 2013 16:28:17 CEST
Install Date : Sun 02 Jun 2013 15:30:35 CEST
Install Reason : Explicitly installed
Install Script : Yes
Validated By : Signature

I am having trouble with my Mac Mini's ethernet connection. Defining a new network interface shows no ethernet adaptor. Reloading SL from DVD repaired. But SL update lost ethernet again. Will Lion Fix?

I am having trouble with my mac mini ethernet. It had been working for weeks after an update to SL 10.6.8.
Once it went out and i repaired it by defining a new connection from System Preferences ->Network->(left panel service, +).
But yesterday, after a power up. my ethernet was not working again. I tried this old trick to repair it, but the interface choices
listed for '+' a new service did not include Ethernet any more. And the Utilities->System Profiler->Ethernet Cards shows
no ethernet available.
As a last ditch effort i reloaded my original SL from DVD. (I think it was version 10.6.4 but i could be mistaken on the version).
The ethernet worked! But KeyNote wasn't going to work because apparently the version i purchased depends on 10.6.8.
So I upgraded again to SL 10.6.8 (Plus some other updates like AirPort which i don't use).
Now the Ethernet is not working again. I see the same symptoms as before with the Ethernet seeming not installed.
Is this a problem seen by others?
Would going to Lion fix the problem?
Could AirPort actually be the culprit and not SL?
If i stay with my original SL, would i need to repurchase a version of KeyNote for the older version of SL?

Have you reset the SMC?
Shut down the computer.
Unplug the computer's power cord.
Wait fifteen seconds.
Attach the computer's power cord.
Wait five seconds, then press the power button to turn on the computer.
While you're at it, resetting the PRAM won't hurt anything and 'might' help is SMC reset didn't work (PRAM does some port control):
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
Something else you might try .... you don't say how you're updating to 10.6.8, however, if you're using Software Update, you might try downloading the 10.6.8 combo update, which contains all updates to 10.6. Sometimes, Software Update doesn't work quite right, and installing the combo update fixes that. Download the update from Apple's download site at http://support.apple.com/downloads/ , using Disk Utility repair permissions, apply the combo update, then repair permissions again.

Iphone 5 trouble with charging, please help?

     Haven't had my iPhone for long (around November for my birthday) and for about the last couple of weeks recently I have had major trouble with the battery charge.
     At first I thought it was the cables, so I got new one after new one and they'd work but then stop working. Until the last one I just purchased, it pretty much stopped charging the phone straight away. No lightening or sound response, no connection via computer etc. So, when my charge ran out I still had it plugged into my computer and now my phone only chargers when it's off when it's plugged into a USB port (bear in mind, it doesn't connect to iTunes-it says USB is unrecognized although it still chargers the phone when off). However, it charges fairly quickly when off but when in use the charge diminishes just as quick as it takes to charge. Not only that but now whenever I wish to turn my iPhone off, it turns itself back on.
      I have recently sent off my phone to the Apple store to have it checked over and it came back to me saying they couldn't reproduce the symptons I had mentioned so there was me thinking everything was fine but nope, still faulty. So a bit disappointed with paying £7.00 for delivery to have nothing been done about it (not only that, but the phone as also out of charge when returned so it just seemed like my phone wasn't looked over one bit). Also a bit disappointed and annoyed at the fact I'm still paying for my monthly contract for the phone when I am unable to use it!!!
     I haven't damaged the phone (it basically looks brand new) and haven't exposed it to any liquids. The USB port on my phone where I charge it seems clear too.
      The annoyance of having to send it back to Apple costing me more money is offputting so does anyone have any other suggestions? I'm going to my local 3 store to see if they can help me out but I'm just a bit fed up now. Can see this is a popular problem amongst other iPhone users too.
Many thanks!
(Oh and need to add I HAVE updated everything on my phone, restored everything, restarted etc.)

Yeah I went to the 3 store and they said that it costs if they find it's a software issue (which I believe isn't fair). However, after sending mine off and having it back exactly the same I headed off to the 3 store and asked to see what they could do for me. Of course, they can't touch Apple phones so they kindly phoned Apple again for me to only say that Apple have NO record of me even sending my phone off even though I have written and e-mail proof. They then said that they replaced my phone in which they didn't. So I spoke to the senior supervisor who said for me to send it off again (yawn) but to be replaced and if it doesn't then I have to e-mail her directly. It's such an annoying issue because I'm still paying for my phone when I can't even use it.
My advice is, definitely go to the store. Even-though they can't actually replace it there and then or send it off themselves to be repaired but they (should) phone up Apple and help you further. Apple shouldn't be asking you for such an upfront cost without even looking at your phone as it could be another issue.
That's me up to date. Sending it off tomorrow, hopefully receive a replaced working phone now.

Trouble with e-mail

I've noticed that I'm having trouble with my .mac/.me account in that I can't seem to send messages anymore. We haven't changed service providers or modems or routers...and it's a problem on the imac and the ibook (4 year differential in age). I've checked all my ports, etc., and I can receive mail but can't send it. Any ideas?
Thanks!

Hi, Amy, and welcome to the Discussions.
This forum is for old, pre-G3 Apple hardware and so probably not the best place for you question. I'd suggest you ask in the MobileMe forums. You'll be more likely to get help there. When you repost, make sure to include information about what you're using to get and send your mail; the Mail application that comes with Mac OS X, a web browser, or something else (and if so, what).
Regards.

Trouble with reauthenticating NAC users after laptop is out of hibernation

Hi,
Have trouble with users logging back on to laptops that comes out of hibernate mode. NAC agent pops up saying " Client Access Server not available on the network"
The current solution I have now is to run Kerbtray.exe too clear the kerberos tkts. which i believe is expired.User logs in fine after clearing.
Is there any alternate permanent soln. in 4.7.2 ver
Thanks in advance
Satish

One more point i forgot to mention
Laptops have full disk encryption installed and encrypts the drive when it goes into hibernation .At the same time the sw port is set to move it to auth vlan after the link down trap is received by the sw.
thanks again
Satish

Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T

Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
I am having trouble making outgoing call or answering incoming call.
When I try to call out from my IP 7961 phone, it fails with the message "unknown number".
For incoming call, it rings but when I pick up the call nothing happens,
Put the receiver back on hook, the phone carries on ringing. I am in UK
and just trying to set up test system with one analogue line. Any help will
be most appreciated. My config of the 2811 router is posted below. All calls ineternally works fine.
Thank you for your help.
hostname Test-CME
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1 10.10.10.10
ip dhcp excluded-address 10.139.139.1 10.139.139.10
ip dhcp pool host
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
option 150 ip 10.10.10.1
ip dhcp pool data
network 10.139.139.0 255.255.255.0
default-router 10.139.139.1
dns-server 10.139.139.5
voice-card 0
no dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
sip
header-passing
registrar server expires max 3600 min 3600
interface FastEthernet0/1
no ip address
no ip mroute-cache
duplex auto
speed auto
no shut
interface FastEthernet0/1.2
description ** Data VLAN **
encapsulation dot1Q 2
ip address 10.139.139.1 255.255.255.0
interface FastEthernet0/1.3
description ** Voice VLAN **
encapsulation dot1Q 3
ip address 10.10.10.1 255.255.255.0
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
tftp-server flash:S00104000100.sbn
tftp-server flash:TERM41.7-0-3-0S.loads
tftp-server flash:term61.default.loads
tftp-server flash:term41.default.loads
tftp-server flash:CVM41.2-0-2-26.sbn
tftp-server flash:cnu41.2-7-6-26.sbn
tftp-server flash:Jar41.2-9-2-26.sbn
tftp-server flash:term70.default.loads
tftp-server flash:term71.default.loads
tftp-server flash:cnu70.2-7-6-26.sbn
tftp-server flash:Jar70.2-9-2-26.sbn
tftp-server flash:TERM70.7-0-3-0S.loads
tftp-server flash:CVM70.2-0-2-26.sbn
control-plane
voice-port 0/3/0
connection plar opx 202
caller-id enable
dial-peer voice 1 pots
incoming called-number .
destination-pattern 9T
port 0/3/0
telephony-service
load 7914 S00104000100
load 7941 TERM41.7-0-3-0S
load 7961 TERM41.7-0-3-0S
load 7970 TERM70.7-0-3-0S
max-ephones 20
max-dn 40
ip source-address 10.10.10.1 port 2000
calling-number initiator
service phone videoCapability 1
system message MKC CME
url services http://10.10.10.1/voiceview/common/login.do
url authentication
http://10.10.10.1/voiceview/authentication/authenticate.do
time-zone 21
date-format dd-mm-yy
voicemail 600
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
moh music-on-hold.au
web admin system name admin secret 0 test
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
secondary-dialtone 9
create cnf-files
ephone-dn 1 dual-line
number 201
label 201
description Sarah
name Sarah
ephone-dn 2 dual-line
number 202
label 202
description Vitthal
name User2 Vitthal
ephone-dn 3 dual-line
number 203 secondary
label 203
description Neil
name User3 Neil
ephone 1
video
username "user1" password 201
mac-address 0018.18EE.947F
type 7961 addon 1 7914
button 1:1
ephone 2
video
username "user2" password 202
mac-address 0018.18BB.B973
type 7941
button 1:2
ephone 3
video
username "user3" password 203
mac-address 0018.1885.6BA2
type 7970
button 1:3

Hi
Please find enclosed debug attachment for voice ccapi and ephone. First, I called from outside. Extension 202 rings but when I answered on extension 202 nothing happens. Replace the rceiever and the pone starts ringing again.Second step. I tried to call out by dialing 9 and then number but after a while phone displays unknown number.
Thank you for your help.
Vitthal

Having Trouble With Formula

i am doing an assignment and im having a lot of trouble with it.
here is what it is asking for
read a value representing a number of seconds, then print the equivalent amount of time as a combination of hours, minutes, and seconds. (For example, 9999 seconds is equivalent to 2 hours, 46 minutes, and 39 seconds).
and so far i have this
package Convert;
import java.util.Scanner;
public class nSeconds {
public static void main(String[] args)
long Seconds = 0;
long Hours = 0;
long Minutes = 0;
Scanner scan = new Scanner(System.in);
System.out.println("Please enter the hours: ");
Hours = scan.nextInt();
System.out.println("Please enter the minutes: ");
Minutes = scan.nextInt();
System.out.println("Please enter the seconds: ");
Seconds = scan.nextInt();
Seconds = (Hours*3600) + (Minutes*60) + (Seconds + 0);
System.out.println("The total number of seconds is: " + Seconds);
please help me with the formula
thanks

sorry that was the wrong app.
this is the code i need help with
package Convert;
import java.util.Scanner;
public class reverseSeconds {
     public static void main(String[] args)
          long Hours = 0;
long Minutes = 0;
long Second = 0;
          Scanner scan = new Scanner (System.in);
          System.out.println ("Please enter in the seconds:");
     Second = scan.nextInt();
     Hours = (Second / 3600);
     Minutes = (Second / 60) + Minutes;
     Second = Second / 60;
     System.out.println ("Hours:" + Hours);
     System.out.println ("Minutes:" + Minutes);
     System.out.println ("Seconds:" + Second);
     System.out.println(Hours + " Hours :" + Minutes + " Minutes:" + Second + " Seconds");
}

Had trouble with iPhone 2.0 upgrade? CHECK YOUR FILESYSTEM!!

I can't find my original post (deleted?), but when I tried to do the first 2.0 iPhone upgrade the day it came out (BIG MISTAKE), I had a lot of trouble. Thanks to an Apple support person who was kind enough to call me, I deleted a file per his suggestion, which made the backup finish to completion and I was happy.
Or so I thought...
Now, several weeks later, I (or rather our IT guy) has discovered that some of my iPhone backup files were corrupted, which has made a mess out of my Macbook Pro (10.4.11)'s file system. It was not fixable with Disk Utility (in the Utilities Folder of the Application Folder) and only partially fixable with Disk Warrior. Nothing appears to be wrong with the hardware (except that my video port was malfunctioning although that problem had started way before the upgrade.)
If you had trouble with the iPhone 2.0 upgrade, I strongly recommend you verify the integrity of your Mac Filesystem. If there's something wrong, you may need expert help in repairing your file system.

Wingstat,
It should still work fine. I have the original iPhone and Apple BT Headset purchased about a year ago. I upgraded to the new 2.0 software 2 weeks ago. BT Headset works fine.
There has always been the occasional incident when I couldn't get the 2 to pair. This was always solved by un-pairing then re-pairing the two manually. To do this:
With your BT Headset:
Press and hold the headset's button until you here the 4, rapid descending tones
Your headset is now off.
On iPhone:
Open SETTINGS, then GENERAL, then BLUETOOTH
Under DEVICES, tap on the iPhone Bluetooth Headset link and select UNPAIR.
Note: If your headset doesn't show up here... keep going...
Tap on the DEVICES link again to put iPhone in DISCOVERABLE MODE
Back to your Headset:
Click and hold the button again... when you hear 4 ascending tones, keep holding
Keep holding the button until you hear 5 rapid, short beeps
Release the button: you're in DISCOVERABLE MODE here too.
Back to your iPhone:
You should see the Headset appear on your DEVICES list.
It should pop up and ask for Pairing Code
Enter 0000 on the iPhone.
You should be all paired up for good now.
Jim

Trouble with linemask-DIO assigning on Port WriteVi

Similar Messages

Maybe you are looking for