Trouble with Mobo running on single channel
I bought a pair of identical 1GB DDR2 PC2-5300 (667mhz) chips for my P4M890/900M2 motherboard and Windows 7 and my bios are only registering 1gb. CPU-Z is showing that I'm running on a single channel only, from what I've looked into, this problem seems to occur only if the chips aren't identical, but mine are; what gives? Anyone have an idea as to whats wrong?
There is no mention of dual channel for this Via chipset:
http://global.msi.eu/index.php?func=proddesc&maincat_no=1&prod_no=1082
http://www.via.com.tw/en/products/chipsets/p4-series/p4m890/
Similar Messages
-
Updated with Yosemite and think that's when my problems started with my IMac being very slow. The color wheel keeps popping up and spinning not allowing me to move forward on typing or moving between websites etc. Extremely slow and never had this problem before Yosemite. Any real answers to this out there? I was on the phone with apple support for two and a half hours the other day and it's not made any difference in what the tech had me do to resolve this issue.
1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
The test works on OS X 10.7 ("Lion") and later. I don't recommend running it on older versions of OS X. It will do no harm, but it won't do much good either.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message. See, for example, this discussion.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. Try to test under conditions that reproduce the problem, as far as possible. For example, if the computer is sometimes, but not always, slow, run the test during a slowdown.
You may have started up in "safe" mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(1266 ' 0.5 0.25 10 1000 15 5120 1000 25000 1 1 0 100 ' 51 25600 4 10 25 5120 102400 1000 25 1 250 40 500 300 85 25 20480 262144 20 2000 524288 604800 5 1024 );k=({Soft,Hard}ware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Extensions Applications Frameworks PrefPane Fonts Displays PCI UniversalAccess InstallHistory ConfigurationProfile AirPort 'com\.apple\.' -\\t N\\/A 'AES|atr|udit|msa|dnse|ax|ensh|fami|FileS|fing|ft[pw]|gedC|kdu|etS|is\.|alk|ODSA|otp|htt|pace|pcas|ps-lp|rexe|rlo|rsh|smb|snm|teln|upd-[aw]|uuc|vix|webf' OSBundle{Require,AllowUserLoa}d 'Mb/s:Mb/s:ms/s:KiB/s:%:total:MB:total:per sec' 'Net in:Net out:I/O wait time:I/O requests:CPU usage:Open files:Memory:Mach ports:File opens:Forks:Failed forks:System errors' 'tsA|[ST]M[HL]' PlistBuddy{,' 2>&1'}' -c Print' 'Info\.plist' CFBundleIdentifier );f=('\n%s'{': ','\n\n'}'%s\n' '\nRAM details\n%s\n' %s{' ','\n'{"${k[22]}",}}'%s\n' '%.1f GiB: %s\n' '\n ...and %s more line(s)\n' '\nContents of %s\n '"${k[22]}"'mod date: %s\n '"${k[22]}"'checksum: %s\n%s\n' );c=(879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 2636415542 3694147963 1233118628 2456546649 2806998573 2778718105 842973933 1383871077 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 3374894509 1051159591 892310726 1707497389 523110921 2883943871 3873345487 );s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[4]} ' s/:$//;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[9]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' BEGIN { FS="\f";if(system("A1 42 83 114")) d="^'"${k[21]}"'launch(d\.peruser\.[0-9]+|ctl\.(Aqua|Background|System))$";} { if($2~/[1-9]/) { $2="status: "$2;printf("'"${f[4]}"'",$1,$2);} else if(!d||$1!~d) print $1;} ' ' $1>1{$NF=$NF" x"$1} /\*/{if(!f)f="\n\t* Code injection"} {$1=""} 1;END{print f} ' ' NR==2&&$4<='${p[7]}'{print $4} ' ' BEGIN{FS=":"} ($1~"wir"&&$2>'${p[22]}') {printf("wired %.1f\n",$2/2^18)} ($1~/P.+ts/&&$2>'${p[19]}') {printf("paged %.1f\n",$2/2^18)} ' '/YLD/s/=/ /p' ' { q=$1;$1="";u=$NF;$NF="";gsub(/ +$/,"");print q"\f"$0"\f"u;} ' ' /^ {6}[^ ]/d;s/:$//;/([^ey]|[^n]e):/d;/e: Y/d;s/: Y.+//g;H;${ g;s/ \n (\n)/\1/g;s/\n +(M[^ ]+)[ -~]+/ (\1)/;s/\n$//;/( {8}[^ ].*){2,}/p;} ' 's:^:/:p;' ' !/, .+:/{print};END{if(NR<'{${p[12]},${p[13]}}')printf("^'"${k[21]}"'.+")} ' '|uniq' ' 1;END { print "/L.+/Scr.+/Templ.+\.app$";print "/L.+/Pri.+\.plugin$";if(NR<'{${p[14]},${p[21]}}') print "^/[Sp].+|'${k[21]}'";} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p;' '&&echo On' '/\.(bundle|component|framework|kext|mdimporter|plugin|qlgenerator|saver|wdgt)$/p' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".","");print $0"$";} END { split("'"${c[*]}"'",c);for(i in c) print "\t"c[i]"$";} ' ' /^\/(Ap|Dev|Inc|Prev)/d;/((iTu|ok).+dle|\.(component|mailbundle|mdimporter|plugin|qlgenerator|saver|wdgt))$/p;' ' BEGIN{ FS="= "} $2 { gsub(/[()"]/,"",$2);print $2;} ' ' /^\//!d;s/^.{5}//;s/ [^/]+\//: \//p;' '>&-||echo No' '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[2]}'{$2=$2-1;print}' ' BEGIN { M1='${p[16]}';M2='${p[18]}';M3='${p[8]}';M4='${p[3]}';} !/^A/{next};/%/ { getline;if($5<M1) o["CPU"]="CPU: user "$2"%, system "$4"%";next;} $2~/^disk/&&$4>M2 { o[$2]=$2": "$3" ops/s, "$4" blocks/s";next;} $2~/^(en[0-9]|bridg)/ { if(o[$2]) { e=$3+$4+$5+$6;if(e) o[$2]=o[$2]"; errors "e"/s";next;};if($4>M3||$6>M4) o[$2]=$2": in "int($4/1024)", out "int($6/1024)" (KiB/s)";} END { for(i in o) print o[i];} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' BEGIN{FS=": "} /^ {10}O/ {exit} /^ {0,12}[^ ]/ {next} $1~"Ne"&&$2!~/^In/{print} $1~"Si" { split($2,a," ");if(a[1]-a[4]<'${p[5]}') print;};$1~"T"&&$2<'${p[20]}'{print};$1~"Se"&&$2!~"2"{print};' ' BEGIN { FS="\f";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1;} ' ' BEGIN { split("'"${p[1]}"'",m);FS="\f";} $2<=m[$1]{next} $1<9 { o[$1]=o[$1]"\n "$3" (UID "$4"): "$2;} $1==9&&$5!~"^/dev" { o[$1]=o[$1]"\n "$3" (UID "$4") => "$5" (status "$6"): "$2;} $1==10&&$5 { p="ps -c -ocomm -p"$5"|sed 1d";p|getline n;close(p);if(n) $5=n;o[$1]=o[$1]"\n "$5" => "$3" (UID "$4"): "$2;} $1~/1[12]/ { o[$1]=o[$1]"\n "$3" (UID "$4", error "$5"): "$2;} END { n=split("'"${k[27]}"'",u,":");for(i=n+1;i<n+4;i++)u[i]=u[n];split("'"${k[28]}"'",l,":");for(i=1;i<13;i++) if(o[i])print "\n"l[i]" ("u[i]")\n"o[i];} ' ' /^ {8}[^ ]/{print} ' ' BEGIN { L='${p[17]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"cksum "F|getline C;split(C, A);C=A[1];"stat -f%Sm "F|getline D;"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("'"${k[30]}"' "F|getline g) { l++;if(l<=L) f=f"\n "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F"\n '"${k[22]}"'"T;printf("'"${f[8]}"'",F,D,C,f);if(l>L) printf("'"${f[7]}"'",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' 's/^.{52}(.+) <.+/\1/p' ' /id: N|te: Y/{i++} END{print i} ' ' /kext:/ { split($0,a,":");p=a[1];k[S]='${k[25]}';k[U]='${k[26]}';v[S]="Safe";v[U]="true";for(i in k) { s=system("'"${k[30]}"'\\ :"k[i]" \""p"\"/*/I*|grep -qw "v[i]);if(!s) a[1]=a[1]" "i;};if(!a[2]) a[2]="'"${k[23]}"'";printf("'"${f[4]}"'",a[1],a[2]);next;} !/^ *$/ { p="'"${k[31]}"'\\ :'"${k[33]}"' \""$0"\"/*/'${k[32]}'";p|getline b;close(p);if(b~/, .+:/||b=="") b="'"${k[23]}"'";printf("'"${f[4]}"'",$0,b);} ' '/ en/!s/\.//p' ' NR>=13 { gsub(/[^0-9]/,"",$1);print;} ' ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?'${k[32]}'$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ / [VY]/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' '/^find: /!p;' ' /^p/{ s/.//g;x;s/\nu/'$'\f''/;s/(\n)c/\1'$'\f''/;s/\n\n//;p;};H;' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;p;' ' s/^.+ |\(.+\)$//g;p;' '1;END{if(NR<'${p[15]}')printf("^/(S|usr/(X|li))")}' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END{ if(i>1)print n} ' s/{'\.|jnl: ','P.+:'}'//;s/ +([0-9]+)(.+)/\2 \1/p' ' /es: ./{ s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/\n.+//p;' ' 1d;/:$/b0'$'\n'' $b0'$'\n'' /(D|^ *Loc.+): /{ s/^.+: //;H;};/(B2|[my]): /H;d;:0'$'\n'' x;/[my]: [AM]|m: I.+p$|^\/Vo/d;s/(^|\n) [ -~]+//g;s/(.+)\n(.+)/\2:\1/;s/\n//g;/[ -~]/p;' 's/$/'$'\f''(0|-(4[34])?)$/p' '|sort'{'|uniq'{,\ -c},\ -nr} ' s/^/'{5,6,7,8}$'\f''/;s/ *'$'\f'' */'$'\f''/g;p;' '/e:/{print $2}' ' /^[(]/{ s/....//;s/$/:/;N;/: [)]$/d;s/\n.+ ([^ ]+).$/\1/;H;};${ g;p;} ' 's/:.+$//p' '|wc -l' /{\\.{kext,xpc,'(appex|pluginkit)'}'\/(Contents\/)?'Info,'Launch[AD].+'}'\.plist$/p' 's/([-+.?])/\\\1/g;p' 's/, /\'$'\n/g;p' ' BEGIN{FS="\f"} { printf("'"${f[6]}"'",$1/2^30,$2);} ' ' /= D/&&$1!~/'{${k[24]},${k[29]}}'/ { getline d;if(d~"t") print $1;} ' ' BEGIN{FS="\t"} NR>1&&$NF!~/0x|\.([0-9]{3,}|[-0-9A-F]{36})$/ { print $NF"\f"a[split($(NF-1),a," ")];} ' '|tail -n'{${p[6]},${p[10]}} ' s/.+bus /Bus: /;s/,.+[(]/ /;s/,.+//p;' ' { $NF=$NF" Errors: "$1;$1="";} 1 ' ' 1s/^/\'$'\n''/;/^ +(([MNPRSV]|De|Li).+|Bus): .|d: Y/d;s/:$//;$d;p;' ' BEGIN { RS=",";FS=":";} $1~"name" { gsub("\"","",$2);print $2;} ' '|grep -q e:/' '/[^ .]/p' '{ print $1}' ' /^ +N.+: [1-9]/ { i++;} END { if(i) print "system: "i;} ' ' NF { print "'{admin,user}' "$NF;exit;} ' ' /se.+ =/,/[\}]/!d;/[=\}]/!p ' ' 3,4d;/^ +D|Of|Fu| [0B]/d;s/^ |:$//g;$!H;${ x;/:/p;} ' ' BEGIN { FS=": ";} NR==1 { sub(":","");h="\n"$1"\n";} /:$/ { l=$1;next;} $1~"S"&&$2!~3 { getline;next;} /^ {6}I/ { i++;L[i]=l" "$2;if(i=='${p[24]}') nextfile;} END { if(i) print h;for(j=0;j<i;j++) print L[i-j];} ' ' /./H;${ x;s/\n//;s/\n/, /g;/,/p;} ' ' {if(int($6)>'${p[25]}')printf("swap used %.1f\n",$6/1024)} ' ' BEGIN{FS="\""} $3~/ t/&&$2!~/'{${k[24]},${k[29]}}'/{print $2} ' ' int($1)>13 ' p ' BEGIN{FS="DB="} { sub(/\.db.*/,".db",$2);print $2;} ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab kextfind top pkgutil "${k[30]}\\" echo cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin' env pluginkit scutil 'dtrace -q -x aggsortrev -n' security sed\ -En awk 'dscl . -read' networksetup mdutil lsof test osascript\ -e netstat mdls route cat uname );c2=(${k[21]}loginwindow\ LoginHook ' /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'" 'L*/Ca*/'${k[21]}'Saf*/E* -d 2 -name '${k[32]} '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' -i '-nl -print' '-F \$Sender -k Level Nle 3 -k Facility Req "'${k[21]}'('{'bird|.*i?clou','lsu|sha'}')"' "-f'%N: %l' Desktop {/,}L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message CRne '0xdc008012|(allow|call)ing|Goog|(mplet|nabl)ed|ry HD|safe b|xpm' -k Message CReq 'bad |Can.t l|corru|dead|fail|GPU |hfs: Ru|inval|Limiti|v_c|NVDA[(]|pagin|Purg(ed|in)|error|Refus|TCON|tim(ed? ?|ing )o|trig|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o%cpu,comm,ruid' "' syscall::recvfrom:return {@a[execname,uid]=sum(arg0)} syscall::sendto:return {@b[execname,uid]=sum(arg0)} syscall::open*:entry {@c[execname,uid,copyinstr(arg0),errno]=count()} syscall::execve:return, syscall::posix_spawn:return {@d[execname,uid,ppid]=count()} syscall::fork:return, syscall::vfork:return, syscall::posix_spawn:return /arg0<0/ {@e[execname,uid,arg0]=count()} syscall:::return /errno!=0/ {@f[execname,uid,errno]=count()} io:::wait-start {self->t=timestamp} io:::wait-done /self->t/ { this->T=timestamp - self->t;@g[execname,uid]=sum(this->T);self->t=0;} io:::start {@h[execname,uid]=sum(args[0]->b_bcount)} tick-10sec { normalize(@a,2560000);normalize(@b,2560000);normalize(@c,10);normalize(@d,10);normalize(@e,10);normalize(@f,10);normalize(@g,10000000);normalize(@h,10240);printa(\"1\f%@d\f%s\f%d\n\",@a);printa(\"2\f%@d\f%s\f%d\n\",@b);printa(\"9\f%@d\f%s\f%d\f%s\f%d\n\",@c);printa(\"10\f%@d\f%s\f%d\f%d\n\",@d);printa(\"11\f%@d\f%s\f%d\f%d\n\",@e);printa(\"12\f%@d\f%s\f%d\f%d\n\",@f);printa(\"3\f%@d\f%s\f%d\n\",@g);printa(\"4\f%@d\f%s\f%d\n\",@h);exit(0);} '" '-f -pfc /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f'$'\f''%Sc'$'\f''%N -t%F {} \;' '/S*/*/Ca*/*xpc*' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' /\ kMDItemContentTypeTree=${k[21]}{bundle,mach-o-dylib} :Label "/p*/e*/{auto*,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {/p*,/usr/local}/e*/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list '-F "" -k Sender hidd -k Level Nle 3' /Library/Preferences/${k[21]}alf\ globalstate --proxy '-n get default' vm.swapusage --dns -get{dnsservers,info} dump-trust-settings\ {-s,-d,} -n1 '-R -ce -l1 -n5 -o'{'prt -stats prt','mem -stats mem'}',command,uid' -kl -l -s\ / '--regexp --files '${k[21]}'pkg.*' '+c0 -i4TCP:0-1023' ${k[21]}dashboard\ layer-gadgets '-d /L*/Mana*/$USER' '-app Safari WebKitDNSPrefetchingEnabled' '-Fcu +c0 -l' -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' '-F \$Message -k Sender kernel -k Message CReq "'{'n Cause: -','(a und|I/O |jnl_io.+)err','USBF:.+bus'}'"' -name\ kMDItem${k[33]} -T\ hfs '-n get default' -listnetworkserviceorder :${k[33]} :CFBundleDisplayName $EUID {'$TMPDIR../C ','/{S*/,}'}'L*/{,Co*/*/*/L*/}{Cache,Log}s -type f -size +'${p[11]}'G -exec stat -f%z'$'\f''%N {} \;' \ /v*/d*/*/*l*d{,.*.$UID}/* '-app Safari UserStyleSheetEnabled' 'L*/A*/Fi*/P*/*/a*.json' users/$USER\ HomeDirectory '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' ' -F "\$Time \$(Sender): \$Message" -k Sender Rne "launchd|nsurls" -k Level Nle 3 -k Facility R'{'ne "user|','eq "'}'console" -k Message CRne "[{}<>]|asser|commit - no t|deprec|done |fmfd|Goog|ksho|ndum|obso|realp|rned f|sandbox ex|/root" ' getenv '/ "kMDItemDateAdded>=\$time.now(-'${p[23]}')&&kMDItem'${k[33]}'=*"' -m\ / '' ' -F "\$Time \$(RefProc): \$Message" -k Sender Req launchd -k Level Nle 3 -k Message Rne "asse|bug|File ex|hij|Ig|Jet|key is|lid t|Plea|ship" ' print{,-disabled}\ {system,user/$UID} -r ' -F "\$Message" -k Sender nsurlstoraged -k Time ge -1h -k Level Nle 4 -k Message Req "^(ER|IN)" ' );N1=${#c2[@]};for j in {0..20};do c2[N1+j]=SP${k[j]}DataType;done;l=({Restricted\ ,Lock,Pro}files POST Battery {Safari,App,{Bad,Loaded}\ kernel,Firefox}\ extensions System\ load boot\ args FileVault\ {2,1} {Kernel,System,Console,launchd}\ log SMC Login\ hook 'I/O per process' 'High file counts' UID {Daemons,Agents}\ {load,disabl}ed {Admin,Root}\ access Stylesheet Library\ paths{,' ('{shell,launchd}\)} Font\ issues Firewall Proxies DNS TCP/IP Wi-Fi 'Elapsed time (sec)' {Root,User}\ crontab {Global,User}' login items' Spotlight Memory\ pressure Listeners Widgets Parental\ Controls Prefetching Nets Volumes {Continuity,I/O,iCloud,HID,HCI}\ errors {User,System}\ caches/logs XPC\ cache Startup\ items Shutdown\ codes Heat Diagnostic\ reports Bad\ {plist,cache}s 'VM (GiB)' Bundles{,' (new)'} Trust\ settings Activity Free\ space );N3=${#l[@]};for i in {0..8};do l[N3+i]=${k[5+i]};done;F() { local x="${s[$1]}";[[ "$x" =~ ^([\&\|\<\>]|$) ]]&&{ printf "$x";return;};:|${c1[30]} "$x" 2>&-;printf "%s \'%s\'" "|${c1[30+$?]}" "$x";};A0() { Q=6;v[2]=1;id -G|grep -qw 80;v[1]=$?;((v[1]))||{ Q=7;sudo -v;v[2]=$?;((v[2]))||Q=8;};v[3]=`date +%s`;date '+Start time: %T %D%n';printf '\n[Process started]\n\n'>&4;printf 'Revision: %s\n\n' ${p[0]};};A1() { local c="${c1[$1]} ${c2[$2]}";shift 2;c="$c ` while [[ "$1" ]];do F $1;shift;done`";((P2))&&{ c="sudo $c";P2=;};v=`eval "$c"`;[[ "$v" ]];};A2() { local c="${c1[$1]}";[[ "$c" =~ ^(awk|sed ) ]]&&c="$c '${s[$2]}'"||c="$c ${c2[$2]}";shift 2;local d=` while [[ "$1" ]];do F $1;shift;done`;((P2))&&{ c="sudo $c";P2=;};local a;v=` while read a;do eval "$c '$a' $d";done<<<"$v";`;[[ "$v" ]];};A3(){ v=$((`date +%s`-v[3]));};export -f A1 A2;B1() { v=No;! ((v[1]))&&{ v=;P1=1;};};eval "`type -a B1|sed '1d;s/1/2/'`";B3(){ v[$1]="$v";};B4() { local i=$1;local j=$2;shift 2;local c="cat` while [[ "$1" ]];do F $1;shift;done`";v[j]=`eval "{ $c;}"<<<"${v[i]}"`;};B5(){ v="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d$'\e' <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F$'\e' ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`egrep -v "${v[$1]}"<<<"$v"|sort`;};eval "`type -a B7|sed '1d;s/7/8/;s/-v //'`";C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { B4 0 0 63&&C1 1 $1;};C4() { echo $'\t'"Part $((++P)) of $Q done at $((`date +%s`-v[3])) sec">&4;};C5() { sudo -k;pbcopy<<<"$o";printf '\n\tThe test results are on the Clipboard.\n\n\tPlease close this window.\n';exit 2>&-;};for i in 1 2;do eval D$((i-1))'() { A'$i' $@;C0;};';for j in 2 3;do eval D$((i+2*j-3))'() { local x=$1;shift;A'$i' $@;C'$j' $x;};';done;done;trap C5 2;o=$({ A0;D0 0 N1+1 2;D0 0 $N1 1;B1;C2 27;B1&&! B2&&C2 28;D2 22 15 63;D0 0 N1+2 3;D0 0 N1+15 17;D4 3 0 N1+3 4;D4 4 0 N1+4 5;D4 N3+4 0 N1+9 59;D0 0 N1+16 99;for i in 0 1 2;do D4 N3+i 0 N1+5+i 6;done;D4 N3+3 0 N1+8 71;D4 62 1 10 7;D4 10 1 11 8;B2&&D4 18 19 53 67;D2 11 2 12 9;D2 12 3 13 10;D2 13 32 70 101 25;D2 71 6 76 13;D2 45 20 52 66;A1 7 77 14;B3 28;A1 20 31 111;B6 0 28 5;B4 0 0 110;C2 66;D4 70 8 15 38;D0 9 16 16 77 45;C4;B2&&D0 35 49 61 75 76 78 45;B2&&{ D0 28 17 45;C4;};D0 12 40 54 16 79 45;D0 12 39 54 16 80 45;D4 31 25 77 15&&{ B4 0 8 103;B4 8 0;A2 18 74;B6 8 0 3;C3 32;};B2&&D4 19 21 0;B2&&D4 40 10 42;D2 2 0 N1+19 46 84;D2 44 34 43 53;D2 59 22 20 32;D2 33 0 N1+14 51;for i in {0..2};do A1 29 35+i 104+i;B3 25+i;done;B6 25 27 5;B6 0 26 5;B4 0 0 110;C2 69;D2 34 21 28 35;D4 35 27 29 36;A1 40 59 81;B3 18;A1 33 60 82;B8 18;B4 0 19 83;A1 27 32 39&&{ B3 20;B4 19 0;A2 33 33 40;B3 21;B6 20 21 3;};C2 36;D4 50 38 5 68;B4 19 0;D5 37 33 34 42;B2&&D4 46 35 45 55;D4 38 0 N1+20 43;B2&&D4 58 4 65 76 91;D4 63 4 19 44 75 95 12;B1&&{ D4 53 5 55 75 69&&D4 51 6 58 31;D4 56 5 56 97 75 98&&D0 0 N1+7 99;D2 55 5 27 84;D4 61 5 54 75 70;D4 14 5 14 96;D4 15 5 72 96;D4 17 5 78 96;C4;};D4 16 5 73 96;A1 13 44 74 18;C4;B3 4;B4 4 0 85;A2 14 61 89;B4 0 5 19 102;A1 17 41 50;B7 5;C3 8;B4 4 0 88;A2 14 24 89;C4;B4 0 6 19 102;B4 4 0 86;A2 14 61 89;B4 0 7 19 102;B5 6 7;B4 0 11 73 102;A1 42 83 114;j=$?;for i in 0 1;do ((! j))||((i))||B2&&A1 18 $((79+i-(i+53)*j)) 107+8*j 94 74;B7 11;B4 0 0 11;C3 23+2*i;D4 24+2*i 14 66+i 92+i;done;D4 60 4 21 24;D4 42 14 1 62;D4 43 37 2 90 48;D4 41 10 42;D2 48 36 47 25;A1 4 3 60&&{ B3 9;A2 14 61;B4 0 10 21;B4 9 0;A2 14 62;B4 0 0 21;B6 0 10 4;C3 5;};D4 9 41 69 100;D2 29 21 68 35;D2 49 21 48 49;B4 4 22 57 102;A1 21 46 56 74;B7 22;B4 0 0 58;C3 47;D4 54 5 7 75 76 69;D4 52 5 8 75 76 69;D4 57 4 64 76 91;D2 0 4 4 84;D2 1 4 51 84;D4 21 22 9 37;D0 0 N1+17 108;A1 23 18 28 89;B4 0 16 22 102;A1 16 25 33;B7 16;B4 0 0 34;D1 31 47;D4 64 4 71 41;D4 65 5 84 116 74;C4;B4 4 12 26 89 23 102;for i in {0..3};do A1 0 N1+10+i 72 74;B7 12;B4 0 0 52;C3 N3+5+i;((i))||C4;done;A1 24 22 29;B7 12;B3 14;A2 39 57 30;B3 15;B6 14 15 4;C3 67;A1 24 75 74;B3 23;A2 39 57 30;B3 24;B6 23 24 4;C3 68;B4 4 13 27 89 65;A1 24 23;B7 13;C3 30;B4 4 0 87;A2 14 61 89 20;B4 0 17;A1 26 50 64;B7 17;C3 6;D0 0 N1+18 109;D4 7 11 6;A3;C2 39;C4;} 4>&2 2>/dev/null;);C5
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, a series of lines will appear in the Terminal window like this:
[Process started]
Part 1 of 8 done at … sec
Part 8 of 8 done at … sec
The test results are on the Clipboard.
Please close this window.
[Process completed]
The intervals between parts won't be exactly equal, but they give a rough indication of progress. The total number of parts may be different from what's shown here.
Wait for the final message "Process completed" to appear. If you don't see it within about ten minutes, the test probably won't complete in a reasonable time. In that case, press the key combination control-C or command-period to stop it and go to the next step. You'll have incomplete results, but still something.
12. When the test is complete, or if you stopped it because it was taking too long, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I may not agree with them.
Copyright © 2014, 2015 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
Running 1Gb Single Channel on Neo2?
Has anyone ran their ram in Single channel dimms 1&3?
With auto setting in the bios, the ram was booting at ddr333, i changed the setting in the bios to ddr400 (200Mhz) and it booted fine but in 2T. Ok as the option in the bios was 'auto', i selected 1T and it wouldnt boot?
The power was on and it seemed to be working but the monitor didnt respond, the light on the monitor was yellow (idle).
Is that normal that 1Gb of ram in Single Channel running DDR400 (200Mhz in bios) at 2T?Slots 1 & 2 - That's the one green and one purple closest to the cpu. The manual is a little confusing when it talks about filling green first, etc.
-
Troubles with timeout using java.nio.channels and non-blocking sockets
Hello.
I have a server application that employs java.nio.channels with non-blocking sockets.
The server waits for connections. The client should connect and be first in sending data.
Timeouts are significant! If client exceeds the allowed time to send data, the server should break the connection.
The huge trouble I've discovered that I cannot control the timeout when client connects but remains silent.
My code looks as follows:
<pre>
Selector oSel;
SocketChannel oSockChan;
Socket oSock;
SelectionKey oSelKey;
Iterator<SelectionKey> oItSelKeys;
int iCurrState, iMask, iCount;
iCurrState = INT_SERVER_WORKING;
iMask = SelectionKey.OP_ACCEPT | SelectionKey.OP_CONNECT | SelectionKey.OP_READ | SelectionKey.OP_WRITE;
while ( iCurrState == INT_SERVER_WORKING )
try
*// retrieving next action*
iCount = oSel.select();
if ( iCount > 0 )
oItSelKeys = oSel.selectedKeys().iterator();
while ( oItSelKeys.hasNext() )
oSelKey = oItSelKeys.next();
oItSelKeys.remove();
if ( oSelKey.isValid() )
switch ( oSelKey.readyOps() & iMask ) {
case SelectionKey.OP_ACCEPT :
oSockChan = oSSockChan.accept();
oSockChan.configureBlocking(false);
oSock = oSockChan.socket();
oSock.setKeepAlive(true);
oSockChan.register(oSel,SelectionKey.OP_READ,new MyPacket(oSock.getInetAddress(),oSock.getPort()));
break;
case SelectionKey.OP_READ :
oSelKey.interestOps(0);
((MyPacket) oSelKey.attachment()).inRequest(); *// preparing request*
this.getReader().add(oSelKey); *// sending key to reading thread*
break;
case SelectionKey.OP_WRITE :
oSelKey.interestOps(0);
((MyRequest) oSelKey.attachment()).inResponse(); *// preparing response*
this.getWriter().add(oSelKey); *// sending key to writing thread*
break;
case SelectionKey.OP_CONNECT :
default :
*// nothing to do*
catch ( IOException oExcept )
*// do some actions*
</pre>
Timeouts are easily controlled by reading and writing threads (see OP_READ and OP_WRITE ).
But when a client just connects without consequent data send, the state of this connection remains as OP_ACCEPT. The connection remains open for arbitrarily large time and I cannot control it!
Please help with idea how can I terminate such connections!How can I process the keys that weren't selected at the bottom of the loop? Should I use the method keys() ?Yes. Form a new set from keys() and removeAll(selectedKeys()). Do that before you process selectedKeys().
And the second moment: as I understood a single key may contain several operations simultaneously? Thus I should use several if's (but not if/else 'cause it's the equivalent of switch ... case ).If there is anything unclear about 'your switch statement is invalid. You need an if/else chain' I fail to see what it is. Try reading it again. And if several ifs were really the equivalent of "switch ... case", there wouldn't be a problem in the first place. They're not, and there is. -
Trouble with TestStand running VB DLLs compiles in separate threads
I have an application that uses DLLs written in VB 6 to manipulate hardware. The hardware is Stepper Motors controlled via the NI CAN bus card, and two instruments controlled via the GPIB PCI card. I have written the two DLLs to use the same NI PCI GPIB and the same NI CAN BUS card. (One instrument per DLL and One Motor per DLL)
Test stand is then creating the DLLs and running them in separate threads. I have the one DLL Call in a subsequence running as a separate thread, and the other DLL is in the main sequence. I have a GOTO step with preconditions set so that the main sequence only continues after the separate thread in the subsequence is finished.
The problem I am having is that these D
LLs work OK when I run them both in the VB debugger. The program even works when I run the main thread in the debugger, and the subsequence is run compiled.
The problem is, that if I try to run both of these DLLs compiled It seems as if the subsequence DLL never executes.To Tuxamation -
Nothing comes to mind as to why this would happen. VB 6 automation DLLs are used all the time for code modules.
Note that when MSVB debugs a DLL, it is actually running the DLL as an EXE server within the MSVB process and not in TestStand's process that is using it. I typically found that there is typically a subtle difference in behavior between running the server as an EXE or DLL server.
A simple way to determine if the TestStand call is reaching your DLL is to place a MsgBox function call in the DLL entry point and immediately return, ie. bybassing your existing code.
So, if the call is being made to your DLL, you could then enable the Visual Basic project option on the Compile tab, "Create Symbol Debug Info" and recreate your VB DLL.
You can then attach Microsoft Visual Studio (C++ debugger) to the TestStand process, open the file that contains the entry point in to DLL that TestStand calls, set a breakpoint, and see if the breakpoint is reached.
Scott Richardson
Scott Richardson
National Instruments -
Single access point with multiple ssids and single channel possible?
Hi everybody.
I have this silly question.
Let say we have three vlans, vlan1,2,3 and they are mapped to wlans as follows:
Vlan 1 ssid1
Vlan 2 ssid2
Vlan3 ssid 3
AP --------trunk------Switchted network.
Our Ap has mobile devices in three wlans, i.e ssid1ssid2 and ssid3
Since AP uses half duplex mode, mobile devices need positive ack from ap before they can send data, therefore once channel let say channel 3( assuming 802.11b is used) can be shared by all mobile devices in three wlans.
Is my understanding correct?
Thanks and have a great weekend.Hii ,
Yes ,that is pretty much possible as suggested by other experts on board. Depending on your access point you will have 1 (2.4 GHz) or both 2.4 & 5GHz radios.
You can configure multiple SSIDs (up to 16 ) known as MBSSID mode in autonomous environment. In Controller based architecture you can configure up to 512 WLAN (SSID) and transmit any 16 of them per AP (using AP group feature). However , it is recommended to keep multiple SSID count below 8 as for each SSID separate beacon will be sent on air which consumes more air time.
Hope this helps
Thanks
Vinay -
TS3276 Trouble with mail running slow
My mail is running very slowly and it looks as if I have more messages saved and coming in that I believe I actually have. I also have a message that reads "connection logging enabled" at the top that seemed to appear about a month ago and I don't know what it means. Any reason for mail running slow, mail messages duplicating multiple times and for trash not emptying as it should?
From the Mail menu bar, select
Window ▹ Connection Doctor
In the window that opens, uncheck the box marked
Log Connection Activity -
Is anyone having trouble with itunes running on Windows server 2008?
We use to have iTunes running on a Dell desktop box that was acting as our file server for years. I upgraded both our hardware to a Dell Pwoeredge server running Windows Server 2008 RS and now I'm finding that iTunes will only stay running for about 3 days. It stops running and has to be force quit and then restarted to get songs playing again. Does anyone know why this is happening and how I can stop it for happening in the future? We use iTunes based music for our on-hold music for our phone system and for in-store ambiance music.
KirkWe use to have iTunes running on a Dell desktop box that was acting as our file server for years. I upgraded both our hardware to a Dell Pwoeredge server running Windows Server 2008 RS and now I'm finding that iTunes will only stay running for about 3 days. It stops running and has to be force quit and then restarted to get songs playing again. Does anyone know why this is happening and how I can stop it for happening in the future? We use iTunes based music for our on-hold music for our phone system and for in-store ambiance music.
Kirk -
I am having trouble with PS running extremely slow any ideas?
My PS is running extremely slow and I have no idea why!
Please read these and proceed accordingly:
http://helpx.adobe.com/photoshop/kb/optimize-performance-photoshop-cs4-cs5.html
http://blogs.adobe.com/crawlspace/2012/07/photoshop-basic-troubleshooting-steps-to-fix-mos t-issues.html
http://forums.adobe.com/docs/DOC-2325 -
DDR2 is seen as single channel???
Thanks in advance for all of your help!
I have a K9N Neo-F MB AM2 socket with a GB of OCZ DDR2 667MHz that is seen by the bios as single channel. Is there a jumper that I need to have connected or is there a bios setting that I need to change? If it is a jumper which one is it?
Thanks,
elitt2Quote from: Fenix on 21-September-06, 22:15:43
Do you have 1 stick or 2?
If it is just one stick then it will only operate at single channel. If you have 2 sticks then make sure that they are in the first 2 slots closest to your CPU (the slots should be colored differently) and then you will have dual channel.
If this does not help then you will need to give us more info about your comp. Like BIOS version, PSU ratings, etc.
I agree unless the RAM is a single then it run's in single channel or IF you have both it could be that you put the wrong dimms which is also another possibility to run in single channel but not in dual channel...Refer to the mobo manual about the RAM setting. (Should be Dimm 1/3 or Dimm 2/4). Gd luck -
Memory trouble with 790FX-GD70
Hi,
Last Saturday, I bought everything located in my signature. There seems to be a problem with the mainboard and the memory, though.
I couldn't install Windows 7, without removing some of the memory, XP went fine.
When running windows, either 7 or XP, with the 8 GB in the pc, it freezes, gives BSOD's, reboots..
I've done a memtest, with all for memory modules, I get errors. If I only have 3 modules in the board, the memtest runs fine. Every memory module in itself works fine. Every slot on the mainboard in itself works fine..
I don't know what might be causing the problem. The mainboard should be able to work with 16GB of memory, why would it fail with 8?Quote from: Hans on 13-August-09, 01:13:52
When you install 3 dimms, the memory runs in single-channel mode which is less demanding on the memory controller which is inside the CPU.
Installing 4 dimms will make all run in dual channel mode which the memory controller cannot handle with 4 dual sided memory dimms. Four single sided dimms can be done. That's why there are 4 dimm slots. And, on top of that, some people seem lucky and can make it work, but they often need to lower clock speed and loosen timings manually.
Reason for all this: it's simply the limitation of the memory controller in the cpu.
Thanks for the information, you've taught me quite a bit.
Quote from: Stu on 13-August-09, 01:46:10
Both are 32bit? In which case you're wasting your time with 8gb of RAM, as you can only use over 4gb with a 64bit OS and 64bit software. There is no point having more than 4gb if you're only using 32bit OS and software, as the rest is unuseable.
No, Win7 RC is 64bit. -
I'm having trouble with a multi channel acquisition and download with PXI-5922
I am having trouble with getting data out from both channels of a PXI-5922. My software seems to be working, but when I do the fetch there is no data for the second channel. I am using the same format for all of the channelList inputs (0,1). I've checked the instrument handles and anything else I can think of, but this is my first time trying to collect data on 2 channels of a digitizer. Any help would be appreciated.
Hi schliepe,
Try checking your code against an existing example. The
Developer Zone Example: Independent
Channel Configuration with NI-SCOPE is a good VI to reference. Also note
that there are several examples that come with the NI-SCOPE driver. They can be
found in Windows by going to Start »
Programs » National Instruments » NI SCOPE » Examples. Additionally, if you find that the examples are not working either, verify that both channels are functioning by running the
NI-SCOPE Soft Front Panel.
Please post back if you have any questions. Have a great
day!
Ryan D.
District Sales Manager for Boston & Northern New England
National Instruments -
K9n2 sli platinum will only boot/post when running single channel
Hey
I am having problems with the rig when i want memory to run Dual channel.
I have tried all bios settings (or at least i think so) and all memory slot combination (or at least i think so) without any luck.
When i put 2 sticks in dimm 1+2 I get nothing but a black screen.
When I then turn my pc off, putting 1 stick in dimm 1 it will boot and I get the message: DQS training failed on previous boot.
Mainboard: MSI K9N2 Sli platinum
CPU: AMD 5600X2 Windsor 2x1mb cache
HD: have tried with WD 250gb and hitachi 160gb sata2
Psu: Have tried with OCZ 500W and corsair 620W
Memory: Have tried with kingston pc5400 and Adata pc6400 both 1gb sticks
GFX: Have tried with GF8800GTS, ATI 1800XT and GF8500GT
CPU cooler: CM Gemini2
Motherboard have BIOS 3.1 ( so there should be no problem with running the cpu)
everything except for mainboard have been testet with other gear and is working 100%
Memory passed memtest with no errors.
Some facts
1 stick in dimm 1 = boot/post single channel
1 stick in dimm 2 = black screen.
1 stick in dimm 3 = boot/post single channel
1 stick in dimm 4 = black screen
1 stick in dimm 1 + 2 = black screen.
1 stick in dimm 1 + 3 = boot/post single channel
1 stck in dimm 2 + 4 black screen
1 stckk in dimm 3 + 4 black screen.
1 stick in 1 + 4 = Boot/postor black screen..cant remember but for sure not dual.
1 stick in 2 + 3 = boot/post or black screen..cant remember but for sure not dual
I have tried:
manual timming settings, both recommended and lower timmings.
Auto timmings
More volt to memory
More volt to cpu
Tried 800, 667, 553 and 400mhz
Tried sli memory disabled and enabled
Changing cpu ratio
Tried T2 and T1
Have tried load default settings
load optimized settings
everything on auto
well, that’s just about it and don’t know what to try next.
So if anybody have some input I would really appreciate it.
Regards
JesperHave you done that?:
Quote from: Stu on 13-September-09, 02:54:40
Have you tried taking the board out of the case and setting up outside on a flat anti-static surface? Maybe there is something shorting the back of the board where the DIMM slot is.
If no change:
Leave just one memory stick in 1st DIMM close to CPU socket,
ensure that system is stable the flash to the latest BIOS ==>
http://eu.msi.com/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=1443
You can >>Use the MSI HQ Forum USB flasher<<
Once done re-test. -
Problem with Set/Get volume of input device with single channel
from Symadept <[email protected]>
to Cocoa Developers <[email protected]>,
coreaudio-api <[email protected]>
date Thu, Dec 10, 2009 at 2:45 PM
subject Problem with Set/Get volume of input device with single channel
mailed-by gmail.com
hide details 2:45 PM (2 hours ago)
Hi,
I am trying to Set/Get Volume level of Input device which has only single channel but no master channel, then it fails to retrieve the kAudioDevicePropertyPreferredChannelsForStereo and intermittently kAudioDevicePropertyVolumeScalar for each channel. But this works well for Output device.
So is there any difference in setting/getting the volume of input channels?
I am pasting the downloadable link to sample.
http://www.4shared.com/file/169494513/f53ed27/VolumeManagerTest.html
Thanks in advance.
Regards
Mustafa
Tags: MacOSX, CoreAudio, Objective C.That works but the the game will not be in full screen, it will have an empty strip at the bottom.
I actually found out what's the problem. I traced the stageWidth and stageHeight during resizing event. I found out that when it first resized, the stage width and height were the size with the notification bar. So when I pass the stage into startling, myStarling = new Starling(Game,stage), the stage is in the wrong size. For some reason, I can only get the correct stage width and height after the third resizing event.
So now I need to restart Starling everytime a resizing event happened. It gives me the right result but I am not sure it is a good idea to do that.
And thanks a lot for your time kglad~I really appriciate your help. -
How to do a single channel DAQ using NI-DAQ driver software with a PCI-MIO-16XE-10 card
Hi,
I would like to find out how I could do a simple one channel Data Acquisition from a signal generator using the NI-DAQ driver software with a PCI-MIO-16XE-10 card.
I have written some test problem but even when the signal generator is turned on/off I get back some weird values.
Here is my code.
CString sFunctionName("");
double volt[OUTPUT_POINTS*2];
double out[OUTPUT_POINTS*2];
short timebase, ready, code, stopped;
unsigned short sampleInterval;
int i, status, count=0;
unsigned long update, points;
short* ai_buffer;
short output_ch_vector[16];
int local_ITERATIONS = 2;
SAFEARRAYBOUND bound[1];
double dataItem = 9.9;
long j;
long k;
double* pTheValues;
LPTSTR lpsz_ErrMsg;
// Initialise device
status = Init_DA_Brds (deviceNumber, deviceNumberCode)
Initializes the hardware and software states of a National Instruments
DAQ device to its default state and returns a numeric device code that
corresponds to the type of device initialized
Init_DA_Brds(DEVICE, &code);
// Check return code from Init_DA_Brds
Code return should be 204: PCI-MIO-16XE-10.
if (code < 0)
CString sError;
sError.Format("Code error: %d", code);
if (code == -1)
sError = sError + ": No device found";
LPTSTR lpsz = new TCHAR[sError.GetLength()+1];
_tcscpy(lpsz, sError);
AfxMessageBox(lpsz);
delete lpsz;
return S_FALSE;
// Allocate memory for analog output and input arrays
//ao_buffer = new short[OUTPUT_POINTS*2];
ai_buffer = new short[OUTPUT_POINTS];
// Set double-buffering
status = DAQ_DB_Config (deviceNumber, DBmode)
Enables or disables double-buffered DAQ operations.
status = DAQ_DB_Config(DEVICE, 1);
if (status < 0 )
sFunctionName = "DAQ_DB_Config";
goto TidyUp;
// Get the rate parameters
status = DAQ_Rate (rate, units, timebase, sampleInterval)
Converts a DAQ rate into the timebase and sample-interval
values needed to produce the rate you want.
status = DAQ_Rate(RATE, 0, &timebase, &sampleInterval);
if (status < 0 )
sFunctionName = "DAQ_Rate";
goto TidyUp;
// Setup scan
status = SCAN_Setup (deviceNumber, numChans, chanVector, gainVector)
Initializes circuitry for a scanned data acquisition operation.
Initialization includes storing a table of the channel sequence
and gain setting for each channel to be digitized
status = SCAN_Setup(DEVICE, 1, ai_channels, gain);
if (status < 0 )
sFunctionName = "SCAN_Setup";
goto TidyUp;
status = SCAN_Start (deviceNumber, buffer, count, sampTimebase,
sampInterval, scanTimebase, scanInterval)
Initiates a multiple-channel scanned data acquisition operation,
with or without interval scanning, and stores its input in an array
status = SCAN_Start(DEVICE, ai_buffer, OUTPUT_POINTS, timebase, sampleInterval, timebase, 1000);
if (status < 0 )
sFunctionName = "SCAN_Start";
goto TidyUp;
while(count < local_ITERATIONS)
// Check whether we are ready to input another half-buffer
status = DAQ_DB_HalfReady(DEVICE, &ready, &stopped);
if (status < 0 )
sFunctionName = "DAQ_DB_HalfReady";
goto TidyUp;
if (ready == 1)
status = DAQ_DB_Transfer(DEVICE, ai_buffer, &points, &stopped);
if (status < 0 )
sFunctionName = "DAQ_DB_Transfer";
goto TidyUp;
count++;
// Clear the analog input
status = DAQ_Clear (deviceNumber)
Cancels the current DAQ operation
(both single-channel and multiple-channel scanned) and reinitializes the DAQ circuitry.
status = DAQ_Clear(DEVICE);
if (status < 0 )
sFunctionName = "DAQ_Clear";
goto TidyUp;
status = SCAN_Demux (buffer, count, numChans, numMuxBrds)
Rearranges, or demultiplexes, data acquired by a SCAN operation
into row-major order, that is, each row of the array holding the
data corresponds to a scanned channel
status = SCAN_Demux(ai_buffer, OUTPUT_POINTS * 2, 2, 0);
if (status < 0 )
sFunctionName = "SCAN_Demux";
goto TidyUp;
//Convert binary values to voltages (Doesn't actually take a reading from board)
status = DAQ_VScale (deviceNumber, chan, gain, gainAdjust, offset, count, binArray, voltArray)
Converts the values of an array of acquired binary data and the gain setting for that data
to actual input voltages measured.
status = DAQ_VScale (1, 0, 1, 1.0, 0.0, OUTPUT_POINTS , ai_buffer, volt);
if (status < 0 )
sFunctionName = "DAQ_VScale";
goto TidyUp;Hello,
Please take a look at lots of examples available at :
1. www.ni.com >> NI Developer Zone >> Development Library >> Measurement Hardware
2. C:\program files\national instruments\ni-daq\examples\visualc
Sincerely,
Sastry V.
Applications Engineer
National Instruments
Maybe you are looking for
-
Is it possible to join a view to a table
Hi all, I need to create a datasource in R3, the basis of the datasource lies in sql statement. In the statement there are lots of "and" and "(+). Within the "and" statement there is also a filter. For example (the sql coding): where rs.docnumber = r
-
Is there any process I can use to allow me to type into my iPad my password. When I open up the device it sets itself up for me to type in my password. The cursor is blinking, the key pad comes up but it does not recognize that I am typing in the pas
-
On unix is it possible to pipe the data to be loaded in to SQL*Loader instead of reading it from file? I have a program that generates data that is to be loaded, and it is a bit waste of time to first save it to file, just to read it back in.
-
HTMLEditorKit: Inserting Custom Tags?
How do you insert a custom tag into a HTML document? I've tried both: HTMLEditorKit.InsertHTMLTextAction( "merge", "<merge name=\"date\">DATE</merge>", HTML.Tag.BODY, new HTML.UnknownTag( "merge" ) )and kit.insertHTML( doc, offset, "<merge name=\"dat
-
Help with creating an action - anto fit an image in a specific pixel size
I am trying to create an action that takes the image in question and fits it with a specific pixel dimension. Some of the images are more horizontal in orientaion (like a school bus) and some are more on the vertical end (Like a tall building) They a