Trouble with new airport- Blinking Amber light
Not sure if this has been answered- but I'm having mucho problems with my new airport express. I am running an powerbook g4 with the original airport- and I want to use the express to extend the range of the airport. However I followed the directions on the apple support- and the light is STILL blinking amber- what's the deal. Can someone help me- step by step (i'm kinda slow...even though it's still apple haha!)
Thanks!
I've had a lot of similar problems, and find the whole process quite frustrating, as the directions are very minimal.
The easiest way that I've come up with is as follows.
1. Perform a hard reset of the AirPort Express. (Use a pen, pencil, or paper clip to hold down the reset btton on the bottom of the unit. Hold the implement in place until the amber light begins to blink rapidly. Release the implement.)
2. Open up the AirPort Setup Assistant (Applications/Utilities/AirPort Setup Assistant).
3. Select the option to set up a new AirPort Base station and select the base station (it will have a weird-looking alphanumeric name).
4. Select the option to join the current network, and then select the option to extend the range of your current network.
The rest is pretty self-explanatory, provided that you know the password to and the name of your main base station as compared to other access points in your network. You want your AirPort Express to be a remote base station and the other to be the main base station, if I'm not mistaken. I hope this helps. Good Luck!
MacBook Pro 17" Mac OS X (10.4.6)
Similar Messages
-
Need help with the contstant blinking amber light
I tried to go into Airport Utility to setup some features on my Airport Extreme N and could not find the device in the list. I have tried to rescan a good number of times, the soft, hard and factory resets, tried reinstalling the software and I have tried to connect to through my desktop via Ethernet. Actually, this is the configuration that I am using to write this post. I can also connect to the Airport Extreme via my iPhone4, which is the sole purpose I bought this thing.
Thanks in advance for the help.Trippe wrote:
I tried to go into Airport Utility to setup some features on my Airport Extreme N and could not find the device in the list.
Welcome to Apple's discussion groups.
I have tried to connect to through my desktop via Ethernet.
If you have a Mac, connecting it to a LAN port on the Extreme with an Ethernet cable should allow AirPort Utility to see the Extreme, presuming that's what you mean you did. (If you have a non-Mac system, there's probably a way to do something similar, but I can't help with the details.) If that's not working -
Airport extreme blinking amber light error when connecting to new modem
I have just bought and installed a new modem gateway. It is an Arris TG852G DOC 3.0 model with a built in WiFi router.
After connecting it and activating it through Comcast, I reset, then reconnected my airport extreme MD0331LL/A Model No. A1408 to the new Arris
modem, I am getting blinking amber lights on the base station. I have internet connectivity, but I am still getting an amber light. My wireless devices (ipad and iphones) all see the old network name and id and seem to work just fine.
When I scanned for my airport base station in my airport utility (version 5.6.1) to try to resolve the error message I get
a message stating that the Airport Utility is not detecting any airport devices.
I cannot reset the default settings as these buttons do not work within the Airport Utility.
I suspect interference between the built in router in the Arris and I understand I need to operate it in bridge mode. Can you please help me fix this.
The COMCAST people are extremely unhelpful, and stated that this is not their problem but a problem with my router
as they have provifded me internet connectivity through the modem and the issue is my problem.Try connecting an Ethernet cable from your computer directly to one of the LAN <-> ports on the AirPort Extreme to see if AirPort Utility can detect the AirPort Extreme that way.
If yes, click on the AirPort Extreme and then click directly on the word Status (2nd line on the summary page)
A window will open to explain why the amber light is blinking
If the message indicates that you need to configure the AirPort in Bridge Mode......
Click the Internet icon at the top of the window
Click the Internet Connection tab just below
Change the setting for Connection Sharing to Off (Bridge Mode)
Click Update at the lower right of the window to save the new setting and restart the AirPort Extreme
You can disconnect the Ethernet cable that you were using to configure the AirPort Extreme now
It would be a good idea to power off both the Arris gateway and the AirPort Extreme now
Wait a minute
Start the Arris first, and let it run a full minute
Start the AirPort Extreme next the same way
You should be all set -
I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?
apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together. -
Airport Express 801.11b/g and the neverending, unconfigurable blinking amber light
Gather round and let me tell you a tale. Once upon a time I bought an airport express 801.11b/g and I was very happy to use it for airtunes, extending a wi-fi network and the wireless printing capabilities. One day, it beagn flashing a scaaaary amber light. The base station stopped showing up in my airport utility 5.6 as well. The only way to get it to show up, was to hard reset it, and lose all the configurations I once enjoyed happily. After the hard reset, It would show up in the utility, and I would reconfigure it to do all its cool things it once did, and it would restart. But sadly, after restarting the blinking amber light came on a again. It would also not show up in the utility unless I hard reset it again, and the same thing happened over and over and over until I felt like pulling my hair out.
I decided to get another airport express a few months later, ultimately deciding that the unit must have just been defective. Bad luck. But - the second unit literally went through the SAME EXACT THING. Worked for a while, then onto the blinking amber light- hard reset- reconfigure-blinking amber light thing. Over and over and over. Just like the first one. The end.
So - either Im missing something totally fundamental or I had the misfortune of getting two defective units in a row. Both were bought used from different places, and worked "fine" for previous owners. Am I corrupting these things or what?
I have spent literally hours trying all the resets, configuring "workarounds" and nothing works. For both of them.
What do I do with these two devices? I don't need two shiny white paperweights.
Please advise,
Thanks.Yes. It seems an integral part of the set up process though, you don't have to seperately configure the airport do you?
My wireless security is WPA/WPA2 Personal. When I go through the standard network set up, it automatically enters my wireless security settings. So it doesn't really seem to give an option to specifically set that option on the airport if that makes sense?
I did go through maunual mode to try that with the same result:
If I'm using the airports own network and connect to the wifi, no security, then I'm getting airtunes from my macbook. Of course this means it's plugged into my router via ethernet which isn't any use to me as I want it in my kitchen, and would rather not limit my apple devices to b/g when I have a decent N router, and would also mean running a huge ethernet cable across my house!
The seller has said it worked for him but he's not up to scratch on his tech, so if I'm sure it's malfunctioning he'll refund. Obviously this is great news and he seems like a very nice guy so I want to be certain it's not me malfunctioning before I send it back!
So in summary I have it functioning on it's OWN network:
Wireless mode: Create a wireless network
Wireless network name: Apple Network XXXXXX
etc
Once 'wireless mode' is switched from 'create a wireless network' to 'join a wireless network' I select my current WiFi, security and password, checked the TCP/IP settings all good. Select 'Update'. Get the warning that device and network will be temporarily unavailable am I sure I want to continue. Then it goes through the same as before, says it's succesful, restarts to flashing amber with no way of accessing it unless I hard reset.
Thanks for the help so far... -
Airport not "recognizing" network - blinking amber light
I just got a new Airport Express. I plugged it in hooked up the ethernet cable to it and all I get is the blinking amber light.
I thought it might need the Cable modem restarted so I did that. Nothing.
I thought it might be an issue with my Vonage adapter. I rebooted that. Nothing.
I bypassed the Vonage completely by directly going from cable modem to Airport Express. Nothing.
I've tried everything but it isn't working.
iBook G4 Mac OS X (10.4.7) 1.33mHz 14.1" 768ram 60gb HDAny time when you reset you have to do it in a specific order to make it work correctly.
The normal reset sequence is to Pull the power adapter from the ISP's Modem and then your Airport Express or Extreme and shut your computer clear off.and next you wait for everything to reset to default settings. (Normally 5 minutes). After your wait you have to plug in the Modem first, wait until it re acquires the signal and all the lights (normally 3) depending on the modem you have. Next Plug in your express or Extreme and again you have to wait a minute and then you can restart your computer.
Be sure before you start the sequence you have the correct setting in System preferences and Network to Airport. and drag it to the top of the list and it has to be highlighted with the little green dot,and be sure you go up to the icon next to your HELP for signal strength and make sure your Airport is ON.
And last welcome to the discussions
Cheers Don -
No Green Light with new AirPort Extreme 802.11n
Bought new AirPort Extreme 802.11n today. DSL works fine with LINKSYS router but only get blinking Amber light with new APE. I am using 10.3.9 so can not use Utility CD as it requires 10.4. Do I have to upgrade system to 10.4 to get APE to work.
Thanks for help. I upgraded to OS X as you all suggested and was able to use AirPort Extreme utility to access web and get the green light. I had to determine how I was connected to internet by DSL provider (PPOE) and needed to insert my mail ID (e-mail address) and my mail password. I was able to verify the PPOE connection by imputting the IP address of the Linksys connection on my browser and going to their web page.
It took me a while but Apple support was available as it was a new purchase and they talked me thru.
JDB -
Airport Utility cannot find Time Capsule and has a blinking amber light
I have a wireless router for my Wifi set up through AT&T (2WIRE). I am trying to add my TC to my existing network rather than establishing a new Wifi network with it. When I try to plug in my TC to set it up, Airport Utility cannot even find it. My TC has a blinking amber light also. I have tried reseting my TC, resetting my router, unplugging my router, unplugging my TC... I have the latest version of Air Port utility (6.2 (620.33)).
Connect the TC LAN port to the computer by ethernet.
If necessary do a reset of the TC so it shows up.
Put the TC into bridge mode.
Go to the wireless page, and set wireless to off.
Update the TC.. disconnect from the PC and plug WAN port to LAN port of the 2wire with ethernet.
The TC will now exist as a client in your network without creating a second wireless network.
You should also be able to access the TC via the airport utility.
I do think you should use the TC wireless since the 2wire does not provide a signal at 5ghz which is much faster than 2.4ghz.
So I do suggest you in fact do use the wireless but it is up to you.
It makes no difference having two wireless networks if they both connect back to the same router.
Do not use the "Join a wireless network" method.. ie no cable between the TC and 2wire.. that is poorest possible setup. -
trying to resolve a blinking amber light on my Time Capsule. The problem is i don't see the airport utilities under Apps/Utilities to try and reset..any ideas?
AirPort Utility should be here: Macintosh HD > Applications > Utilities > AirPort Utility
If it is not there, you can download it from here:
http://support.apple.com/downloads/#airport
Temporarily, connect an Etherent cable from your Mac to one of the LAN <-> ports on the back of the Time Capsule
Open AirPort Utility - Click Manual Setup
Click directly on the word Status (2nd line) and a window will open to explain why the Time Capsule is complaining along with suggested actions to remedy the issue -
Airport Express won't connect to network, blinking amber light, and "unexpected error occurred."
I have two aiport expresses - both have the problem. Both continue to have a blinking amber light, when I go through all the setup activities, after completing the factory reset multiple times, I simply get "An unexpected error occurred."
In fact after I do this, my laptop has issues connecting to the network. I have Verizon Fios, not sure if that means anything.
Haven't seen this covered in any of the troubleshooting materials; they just keep going to factory reset to solve all problems, which I've done several times with each device to the same end.
Any ideas?Hi - You can install 5.6 on Mountain Lion but it is tricky - here are instructions from a post by guru Bob Timmons -
The workaround is to use a utility like Pacifist to manually extract the application and then manually install it in the Utilities folder - see this link:
http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html
Another workaround....if you have Time Machine backups.....is to back in time to locate AirPort Utility 5.6 and restore it to the desktop. Then drag it into the Utilities folder. -
Airport extreme slow blinking amber light. Can't see through airport utility.
Unsuccesful trying to reset. On a hard reset, it still goes from steady amber to slow blinking amber. Never get a rapid blinking amber light. Have tried to connect directly to it via ethernet and airport utility doesn't see it. Any help?
I have this same issue. Internet works, I can connect to it, but i doesn't show in the Airport Utility. Also, it doesn't let me connect to other computers or my AirDIsk. I am using 10.5. Unplug and plugin style reset fixes it...for a while. Any ideas anyone?
-
I recently bought an Airport Express and connected it to my TimeWarner modem. Am able to surf the internet using my MacBook Air, iPad, and Apple TV, but the AirPort Express has a blinking amber light. How could I change it to a green light?
The following may help: Wi-Fi base station: Understanding and resolving a blinking amber status light
-
I have tried to set up airport extreme base stations but keep getting blinking amber lights. Have unplugged and reset. No base station prompt noted in the airport utility window. Internet connetion noted (Green light under globe icon)
Are you using 6.0 here?
What kind of AEXT are you using? -
A blinking amber light doesn't necessarily mean that something is wrong.
Yesterday I set up a new AEBSn in bridge mode so that an attached hard disk could be shared by two Mac computers connecting to the AEBSn wirelessly pending inauguration of a new DSL connection.
Although the configuration worked perfectly, the amber light continually blinked because the AEBSn sensed that an Ethernet cable was unplugged even though the configuration did not call for any Ethernet connections.
Interestingly, the blinking amber light turned to solid green as soon as I added two network printers via Ethernet cables.Just wanted to make sure you know that if the amber light is blinking, you can run the new Airport Utility and when the wireless devices appear on the left hand side of the page, anyone that is flasking amber will show up with a flashing amber light. If you double click on that device a new window will come up. On the summary page you'll see a line that says name of device and it will have a status light next to it that is the same as the status light on the equipment. In this case a flashing amber light. If you double click on the flashing symbol it will give you the reason for the flashing amber light.
In most cases at this point, the flashing amber light is usually because there was no security applied to the system.
If you opt, you can also turn off the amber light if you can live with the problem. -
Still have blinking amber light
I've followed the instructions. I've searched the support board, and I still can't get my airport express to work. I've reset it to factory settings, I've unplugged the cable modem and left it off for 15 minutes then replugged everything.
My Macbook "sees" the airport, it says the AX is working, but there's no Internet connection (blinking amber light). I have two AX's set up elsewhere just fine, but I'm trying to set this one up with no luck.
HELP!Hi Mary,
Welcome to the forum.
First question is: How old is the Express that is a problem? If it is two years or older it may have reached the end of its life cycle.
After you have reset it to factory settings, it should show up in the setup assistant or Airport Utility with its original Apple factory ID. When you join it to the system, do not name it the same name that you have named it before. What I usually do is add a word in front of the old name like "new" or add a number behind it. It may see the Airport but if the Airport is in actually not tied to your wireless system it won't connect.
Maybe you are looking for
-
Exchange Server 2010 Room Mailboxes Double Booking
We are have several room mailboxes setup on Exchange Server 2010 and are having an issue with rooms being double booked. I have "Allow Conflicting Meeting Requests" unchecked on the Resource Policy Tab but if a user try's to book a room that is alrea
-
If this error appears in IE,the error will resolved by registering the component. But not in FF 3.6.11
-
Setting NLS_LENGTH_SEMANTICS for a Module or session
Hi, We have a DW loading data from three source databases. One of the source databases has started using UTF-8, which entails NLS_LENGTH_SEMANTICS = CHAR. Another source database will follow later this year. The third one is Oracle Applications, whic
-
Hi All, Can anyone explain in detail How the goods movement types, transaction event keys, G/l accounts, valuation class are linked? thankyou in advance, Prasad.
-
Hi frends, Iam using the FM 'KCD_EXCEL_OLE_TO_INT_CONVERT' to upload the data of transcation code 'F-02' using session method and call transaction method. what feilds i have to use in progmme. I want the progmme codes. Plz help me, Thanks and regard