Trouble With Port Mirroring (SG200-08)

Trouble with port mirroring.
Even though both Tx and Rx is specified, only getting half the conversation.  Ping reply only for instance.  And when pinging from other locations no traffic at all.
Please help
SG200-008
FW Version: 1.0.2.0
Boot Version D.3.1
Thanks

I also have problem with the mirroring of port on my SG200-08.  The firmware is 1.0.6.2.
I mirror the port g1, to which my router to the Internet is connected, to the port g2 to be able to see the traffic with a Centos system running Bandwidthd connected to the port g2.  The problem is that I only see the traffic coming in (downloads from the Internet) and not the traffic comming out (uploads to the Internet).
When looking at the SG 200-08 on the web interface at "Status and Statistics/Interface" and looking at the port g2, I see values for the "Transmit Statistics", but all the values are at 0 for the "Received Statisticsc" (see the attached file)
I confirmed that in "Administration/Diagnostic/Port Mirroring" is set up both Tx and Rx (it does not work either if I have Tx or Rx alone: I do not see the uploda traffic to the Internet). See the attached file.
This is very annoying as I purchased this SG 200-08 especially for this and it does not do the job porperly.
Does anybody knows a solution to this?

Similar Messages

  • Trouble with port forwarding, DHCP, VUZE, and downloading speed.

    I am using Vuze to download things. I have a slow download speed and yellow smiley face, indicating a NAT problem. I think I need to implement a port forwarding, but that requires a static IP address. My router and security is set up such that I CANNOT connect to the internet using a manual configuration--DHCP only. However, I always have the same IP address. This is because the wireless router--a Motorola SB900--will only recognize approved computers designated by the IP address.
    Can anyone advise on what to do next?

    Enmnm wrote:
    I am using Vuze to download things. I have a slow download speed and yellow smiley face, indicating a NAT problem.
    Here are two links that will rate your connection.
    http://www.speedtest.net/
    http://www.pingtest.net/
    You can try downloading directly from the terminal to see how fast one file downloads.
    Macintosh-HD -> Applications -> Utilities -> Terminal
    mac $ mkdir test
    mac $ cd test
    mac $ curl "http://www.apple.com" >see
      % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                     Dload  Upload   Total   Spent    Left  Speed
    100 11292  100 11292    0     0  22628      0 --:--:-- --:--:-- --:--:-- 62623
    mac $ cat see
    <!DOCTYPE html>
    <html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en-us" lang="en-US">
    <head>
    ... clipped ...
    I think I need to implement a port forwarding, but that requires a static IP address. My router and security is set up such that I CANNOT connect to the internet using a manual configuration--DHCP only.
    you are dealing with two networks. There is a network between your computer and your router. There is a second network between your router and your ISP.
    Port-forwarding is from your router to your computer.
    http://www.portforward.com/english/routers/port_forwarding/Motorola/SBG900/Azure us.htm
    However, I always have the same IP address. This is because the wireless router--a Motorola SB900--will only recognize approved computers designated by the IP address.
    Can anyone advise on what to do next?
    You need to set Port-forwarding between your computer and your router. You will need a fixed IP address on a your Computer. There is to ways of doing this. You can set up a static IP address on your computer. A hack would be to add 10 or 20 to your IP address that your router gives out. For example if your router gives out 192.168.1.10 you of would add 10 to the ten giving 192.168.1.20. you need to make the addition to the right most number of which in the example is ten.
    The section way is . . . You can have your router a signed a fixed address based on your MAC address. ( Each Internet device has a fixed address that is called the MAC address. This is a different address than your IP address. the MAC address is assigned in the factory. )
    Another hack would be to Port-forward to the number your router assigned at random. If your Computer is the only computer on the router, the number should always be the same. It is a hack because this is not guaranteed.

  • Is anyone having trouble with airplay mirroring after the 5.2 update?

    I just updated my apple tv to 5.2 and now I experience freezing of the video after awhile. I can watch streaming content and then the video will stop but audio continues. I'm using an imac with mountain lion and i use a dual band n router.

    Hello there, T'Quananmy
    The following Knowledge Base article, although written for iPhone is applicable for troubleshooting issues with the speaker on your iPad as well:
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/ts5180
    Verify that the volume is set to a level you would normally be able to hear.
    Ensure that there is nothing plugged in to the headset jack or the dock connector.
    If the iPhone is in a protective case, make sure that the speaker port isn't blocked by the case.
    Make sure that the speaker and dock port aren't clogged with debris. If necessary, clean it with a clean, small, dry, soft-bristled brush. Carefully and gently brush away any debris.
    If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
    If the iPhone is paired with a Bluetooth headset or car kit:
    Try turning off Bluetooth.
    If you experience difficulties with the Bluetooth feature, follow these troubleshooting steps.
    Restart the iPhone.
    If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
    If the issue is not resolved, please  contact Apple Support.
    Learn more about troubleshooting iPhone hardware issues.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • Trouble with port fowarding

    I type the application name, the start and end port, the protocol and the ip address. When I hit 'Enable', I get this message: "You cannot use the router ip, network broadcast address." I've tried my private IP address and i've tried "192.168.1.0". What am I doing wrong?

    That would be because that is the routers address, more likely you are looking for a number in the list that says something like 192.168.1.100 192.168.1.101 192.168.1.102 192.168.1.103 that is the type of number you should be seeing at the top of the cmd prompt after entering that in scroll all the way back up too where you put in the command and look for something like that instead
    Vista Ultimate 32 Bit
    AMD 64 X2 6400+ Black Edition
    4BG RAM
    1.18 Terabytes Of Hard Drive Space
    Acer 22inch Widescreen LCD
    Nvidia 8600 GT PCI E 512 DDR3
    WRT54G Router
    Netgear Gigabit Switch
    Motorola 2210 Modem

  • SG300-28 Port Mirroring

    Hello,
    I am wondering if anyone else has issues with port mirrors? I have created a mirror to copy all packets from Interface gi1 to interface gi28. I don't see any port 80 traffic, or 443 or any revelant traffic. I see mostly broadcast from other devices. I have a security device that is logging all the copied packets from my firewall for malware/IPS, etc inspection.
    Right now I have it monitoring vlan 1 in the hope that it would resolve this issue but I see no change. The config is attached for viewing.
    Any thoughs?

    Hi Alan, try to monitor a specific port instead of the whole VLAN.
    -Tom
    Please mark answered for helpful posts

  • Port mirroring on SRW2048 kills Wireshark workstation IP

    I have a workstation on this switch that is running WireShark and I need to get packets to it.  However the moment I turn on port mirroring the station loses IP connectivity to the network.  I tried Rx only, Tx only and both and all three settings knock the workstation off the IP network.  Is there something I am missing?  Also, I noticed that I can only mirror 4 source ports to this one target port.  I would like to select pretty  much all the ports as source port.  Why can't I do this?  I was previously using an older DLink switch that allowed me to mirror all ports and I am pretty sure that other switches like the Cisco 2900 series let you select all ports as source ports.
    Thanks,
    Diego

    I fully understand what you are saying but that isn't consistent with previous experiences with port mirroring.  I have used Cisco Catalyst type switches and also DLink switches that allow you to mirror all ports on the switch to one destination port.  And even with all ports mirrored IP connectivity to the destination port is maintained. 
    This is not so surprising on the Catalyst stuff which is considered maybe a bit more "high end" than Linksys but the DLink which is a cheaper switch has the ability to do this just as the Catalyst.  It seems that the Linksys is inferior in this regard to the Catalyst and the DLink.
    Sorry to hear that and hopefully a future firmware version will change this behavior.
    Thank you very much for your help.
    Rgds,
    Diego

  • RV180 Port Mirroring

    Has anyone had any success with port mirroring on the RV180?
    The data sheet refers to port mirroring capability, but I can't find the configuration settings anywhere?

    Duplicate posts.  
    Go here:  http://supportforums.cisco.com/discussion/12156511/rv180-port-mirroring

  • Hyper-V WMI Provider - Searching and Setting Port Mirroring

    Is there any way to search for VMs with Port Mirroring disabled through WMI provider?? I'm working on a little application to set port mirroring to destination but I can't find anything in WMI Provider API. I know this can be achieved using PowerShell
    cmdlets but I would rather use WMI and C# if possible. Thanks.

    Hi PerlFanatic ,
    Please refer to following command :
    Get-WmiObject -Namespace root\virtualization\v2 -Class msvm_ethernetswitchportsecuritysetting
    data
    Best Regards
    Elton JI
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Trouble with bridge mode and port forwarding

    I have a Westell Model 6100F DSL modem in bridge mode into my network and I'm having trouble forwarding ports. Is there any general guidance available to do this. I have set many of my friends networks up to allow port forwarding but all have been on other service providers, mainly cable. (my experience) My network is the only one I have had trouble with.
    Basically, my question is, while in bridge mode, does the modem forward all incoming traffic to my NAT router or do I need to apply special port forwarding settings in the modem to allow this?
    If bridge mode is the reason I cannot forward the ports, can someone explain how to set the WEstell 6100F back to factory defaults so I can start over. 
    Any other suggestions?
    Thanks in advance.
    Paul

    If bridge mode is set up correctly, your router should be holding the Public IP address (basically not something that is a 192.168 address) as shown at http://www.whatismyip.com/ and compared against what IP your router has.
    If your router has the public IP, all problems lie with either your router or your PC's firewall and configuration. I'd check out portforward.com for some guides on forwarding ports for your router or poarticular application if you need some additional help.
    ========
    The first to bring me 1Gbps Fiber for $30/m wins!

  • PORT MIRRORING WITH SRW2048

    HI ALL,
    I am using  SRW2048. When I am doing port mirroring, my target port is not working. it is disconnecting from lan.
    Please suggest me how can I do port mirrioring with SRW2048.
    Thanks

    1. The source port is the one you want to mirror.
    2. The target port is the one to which you mirror, i.e. the target port receives the mirror copies of the source port traffic, i.e. it is the port to which you connect the network analyzer.
    3. On the SRW switches the target port does not allow LAN access. In mirror mode it ignores any traffic which you send from the device connected to the target port. If the network analyzer requires additional LAN access you'll need another LAN connection to another port, i.e. two LAN ports on the analyzer. There is no other way.

  • Port mirroring with ALOT of Drops Tx on a 5406zl

    Hi everybody.
    My first post here and I'm convinced that the questions I have will be easily answered by several of the true experts that reside here in the forum.
    Question #1.
    I've set up port mirroring this way on my HP procurve J8697A Switch 5406zl (Software revision K.15.12.0015)
    sw-dh-1(config)# show monitor 1
    Network Monitoring
       Session: 4    Session Name:
          Mirror Destination:  B13   (Port)
          Monitoring Sources  Direction Truncation Mirror Policy
          Port: F1            Both       No         -
          Port: F2            Both       No         -
          Port: F3            Both       No         -
          sw-dh-1# show monitor 2
    Network Monitoring
       Session: 3    Session Name:
          Mirror Destination:  A6    (Port)
          Monitoring Sources  Direction Truncation Mirror Policy
          Port: A7            Both       No         -
          Port: B6            Both       No         -
          Port: B10           Both       No         -
          Port: Trk5          Both       No         -
          Port: Trk9          Both       No         -
          Port: Trk11         Both       No         -
    See output of "show interface" below. I'm worried about "Drop Tx". What does that mean exactly? Are mirrored packets dropped or does this mean that the ordinary traffic on the monitoring ports are also affected? If yes, how? Data loss, resending packets, loss of speed, high CPU load on the switch?
    sw-dh-1# show interfaces B13
     Status and Counters - Port Counters for port B13
      Name  : <removed>
      MAC Address      : xxxxxx-xxxxx
      Link Status      : Up
      Totals (Since boot or last clear) :
       Bytes Rx        : 576                Bytes Tx        : 4,252,895,128
       Unicast Rx      : 0                  Unicast Tx      : 3,440,299,294
       Bcast/Mcast Rx  : 9                  Bcast/Mcast Tx  : 412,639,331
      Errors (Since boot or last clear) :
       FCS Rx          : 0                  Drops Tx        : 29,441,235
       Alignment Rx    : 0                  Collisions Tx   : 0
       Runts Rx        : 0                  Late Colln Tx   : 0
       Giants Rx       : 0                  Excessive Colln : 0
       Total Rx Errors : 0                  Deferred Tx     : 0
      Others (Since boot or last clear) :
       Discard Rx      : 0                  Out Queue Len   : 0
       Unknown Protos  : 0
      Rates (5 minute weighted average) :
       Total Rx  (bps) : 0                  Total Tx  (bps) : 5,002,088
       Unicast Rx (Pkts/sec) : 0            Unicast Tx (Pkts/sec) : 0
       B/Mcast Rx (Pkts/sec) : 0            B/Mcast Tx (Pkts/sec) : 6
       Utilization Rx  :     0 %            Utilization Tx  : 0.50 %
    sw-dh-1# show interfaces A6
     Status and Counters - Port Counters for port A6
      Name  : <removed>
      MAC Address      : xxxxx-xxxxx
      Link Status      : Up
      Totals (Since boot or last clear) :
       Bytes Rx        : 960                Bytes Tx        : 1,442,037,177
       Unicast Rx      : 0                  Unicast Tx      : 1,988,961,810
       Bcast/Mcast Rx  : 15                 Bcast/Mcast Tx  : 339,915,002
      Errors (Since boot or last clear) :
       FCS Rx          : 0                  Drops Tx        : 1,647,165,303
       Alignment Rx    : 0                  Collisions Tx   : 0
       Runts Rx        : 0                  Late Colln Tx   : 0
       Giants Rx       : 0                  Excessive Colln : 0
       Total Rx Errors : 0                  Deferred Tx     : 0
      Others (Since boot or last clear) :
       Discard Rx      : 0                  Out Queue Len   : 0
       Unknown Protos  : 0
      Rates (5 minute weighted average) :
       Total Rx  (bps) : 0                  Total Tx  (bps) : 5,000,000
       Unicast Rx (Pkts/sec) : 0            Unicast Tx (Pkts/sec) : 0
       B/Mcast Rx (Pkts/sec) : 0            B/Mcast Tx (Pkts/sec) : 0
       Utilization Rx  :     0 %            Utilization Tx  : 0.50 %
    Utilzation and total last 5 minutes is off since I turned the mirroring off when I saw the drops. Utilization when port mirroring was on was 20-35%.   
    Question #2:
    Is it better if I mirror out all traffic to the 10GB port instead? Assuming that it is possible to do port mirroring to the 10GB port?
    best regards,
    Dean Y

    You don;t indicate which router you have, but that doesn;t really matter.Neither the Actiontec MI424-WR or the Quantum G1100 have port mirroring.  You need qan old fashioned hub, or a managed switch that supports it. 

  • Trouble with Teamspeak & XFi

    on XP I had no problems, but in Vista I get "echos" , like a person say "hello" I get 4-5 of them. I use Vista 64-bit, XFi is the fatality card with the new WHQL drivers. any suggestions, I have tried to change the priority of teamspeak from the task manager, but it did not help?It normalt hapen when I has 2-3 sessions of eve-online(no sound)?running (on 32-bit XP, I could run 4 with no teamspeak issues). Sound is otherwise fine. Quick spec:?64 bit Vista PremiumE6600, 4Gb ram, 8800, Xfi, raptor?

    I also have problem with the mirroring of port on my SG200-08.  The firmware is 1.0.6.2.
    I mirror the port g1, to which my router to the Internet is connected, to the port g2 to be able to see the traffic with a Centos system running Bandwidthd connected to the port g2.  The problem is that I only see the traffic coming in (downloads from the Internet) and not the traffic comming out (uploads to the Internet).
    When looking at the SG 200-08 on the web interface at "Status and Statistics/Interface" and looking at the port g2, I see values for the "Transmit Statistics", but all the values are at 0 for the "Received Statisticsc" (see the attached file)
    I confirmed that in "Administration/Diagnostic/Port Mirroring" is set up both Tx and Rx (it does not work either if I have Tx or Rx alone: I do not see the uploda traffic to the Internet). See the attached file.
    This is very annoying as I purchased this SG 200-08 especially for this and it does not do the job porperly.
    Does anybody knows a solution to this?

  • Trouble with printjobmgr

    I have seen from posts here that printjobmgr gives some CPU usage issues. I wonder if anyone can help with this one?
    Activity monitor shows that printjobmgr is running at about 100 and the %user is at over 50. I tried to quit the process but it just comes straight back (even in force quit).
    Can anyone tell me how to get rid of this? Do I need to do a re-install?
    This is on a 2Gb MacBook running 10.5.5
    Many thanks

    I also have problem with the mirroring of port on my SG200-08.  The firmware is 1.0.6.2.
    I mirror the port g1, to which my router to the Internet is connected, to the port g2 to be able to see the traffic with a Centos system running Bandwidthd connected to the port g2.  The problem is that I only see the traffic coming in (downloads from the Internet) and not the traffic comming out (uploads to the Internet).
    When looking at the SG 200-08 on the web interface at "Status and Statistics/Interface" and looking at the port g2, I see values for the "Transmit Statistics", but all the values are at 0 for the "Received Statisticsc" (see the attached file)
    I confirmed that in "Administration/Diagnostic/Port Mirroring" is set up both Tx and Rx (it does not work either if I have Tx or Rx alone: I do not see the uploda traffic to the Internet). See the attached file.
    This is very annoying as I purchased this SG 200-08 especially for this and it does not do the job porperly.
    Does anybody knows a solution to this?

  • Trouble with inviting attendees

    I no longer am able to respond to invitations. i get a server error. also notifications don't show up in the notification box in ical.
    anyone have an idea what is going on?

    I also have problem with the mirroring of port on my SG200-08.  The firmware is 1.0.6.2.
    I mirror the port g1, to which my router to the Internet is connected, to the port g2 to be able to see the traffic with a Centos system running Bandwidthd connected to the port g2.  The problem is that I only see the traffic coming in (downloads from the Internet) and not the traffic comming out (uploads to the Internet).
    When looking at the SG 200-08 on the web interface at "Status and Statistics/Interface" and looking at the port g2, I see values for the "Transmit Statistics", but all the values are at 0 for the "Received Statisticsc" (see the attached file)
    I confirmed that in "Administration/Diagnostic/Port Mirroring" is set up both Tx and Rx (it does not work either if I have Tx or Rx alone: I do not see the uploda traffic to the Internet). See the attached file.
    This is very annoying as I purchased this SG 200-08 especially for this and it does not do the job porperly.
    Does anybody knows a solution to this?

  • Trouble with BBAlert

    I downloaded BlackBerry Alerts to my computer and when trying to interface with the Blackberry Desktop Manager I keep getting the error "please update your desktop software" but I have the latest desktop software.  Any ideas are greatly appreciated as the only thing I don't like about my Blackberry is not getting an audible reminder of a missed call or text.  Thanks

    I also have problem with the mirroring of port on my SG200-08.  The firmware is 1.0.6.2.
    I mirror the port g1, to which my router to the Internet is connected, to the port g2 to be able to see the traffic with a Centos system running Bandwidthd connected to the port g2.  The problem is that I only see the traffic coming in (downloads from the Internet) and not the traffic comming out (uploads to the Internet).
    When looking at the SG 200-08 on the web interface at "Status and Statistics/Interface" and looking at the port g2, I see values for the "Transmit Statistics", but all the values are at 0 for the "Received Statisticsc" (see the attached file)
    I confirmed that in "Administration/Diagnostic/Port Mirroring" is set up both Tx and Rx (it does not work either if I have Tx or Rx alone: I do not see the uploda traffic to the Internet). See the attached file.
    This is very annoying as I purchased this SG 200-08 especially for this and it does not do the job porperly.
    Does anybody knows a solution to this?

Maybe you are looking for

  • Apple TV iTunes Playback Glitch

    Sometimes when I am playing music from my iTunes on my MacBook, designated to playback on Apple TV, I don't hear anything.  To fix the problem, I have to (while playback is happening) change destination from Apple TV to Compute back to Apple TV.  The

  • Thunderbolt and DVI splitter

    I have two DVI/VGA monitors I use for work and looking to see if there is a splitter from a thunderbolt port that would let me use these with my Macbook Air.  My Air does support thunderbolt displays just been trying to google such an item and not su

  • Session (attribute) lost between JSPs

    Hi All I've seen many post about losing the session but all of them (the ones I've seen) are different. Anyway, I have 3 jsp's, the first only submits a form like <FORM METHOD=POST ACTION="SaveName.jsp"> What's your name? <INPUT TYPE=TEXT NAME=userna

  • Error starting the engine

    Hola acabo de agregar una nueva actividad interactiva con un flujo de pantalla de un jsp y a la hor de intentar encender el motor me saca una ventana de erroir diciendo "Error en la publicacion dle proyecto. Motivo se deben de cumplir todos los argum

  • Generating an HTML report from two tabs.

    Hi Guys, and sorry if the title is not clear. My situation is like this: I have two tabs for two different conditions. In the first tab, I want generate part of my HTML report regarding the first tab. Then, in the second tab, I want add more details