Trouble with PYRO a/v link capture device & Tiger

Hi, all.
I am new to Tiger.
I was told that this PYRO A/V link was a good product and I bought it. Just ignored that there isn't written TIGER on it!
What can I do now?
Mac just doesn't see it!
Help, please!

On the box it reads: os9 osX ... panther
By the way, I had a chance to make some tests, and I discovered that the Firewire port works (Phew!), I connected an Ipod to it, and it's OK.
I have been to the shop and they changed the PYRO, just to be sure, but the effect is the same.
Also, a previous poster said that he is OK with PYRO and Tiger...
Maybe he upgraded from Panther so he has got the 'old' firewire drivers...

Similar Messages

Switched from a PC to a MBP, having trouble with iTunes syncing iPhones, iPods. Devices are still linked to the PC ?

Switched from a PC to a MBP, having trouble with iTunes syncing iPhones, iPods. Devices are still linked to the PC. How do I undo the PC link without a restore / reformat?

Post in the iTunes forum:
https://discussions.apple.com/community/itunes
Read:
http://www.apple.com/support/switch101/
http://www.macworld.com/article/1153952/superguide_switchingtoamac.html

I am having trouble with some of my links having images. For example, Foxfire has a picture that looks like a small world. The links in question are blank.

I am having trouble with my links/websites having images attached to them. The place where the image should be is blank. For example, AARP has an A for its image. My storage website has a blank broken box where the image should be. I forgot I had trouble and had to reset Foxfire, this problem occurred after that reset.

cor-el,
Mixed content normally gives the world globe image, unless you are using a theme that uses a broken padlock instead. Maybe the gray triangle means invalid? I came across that in a few themes (what is invalid was not made clear), but those were not using triangle shapes to indicate that.
I came across that mention in one of the pages you posted:
* https://support.mozilla.org/kb/Site+Identity+Button
I cannot attach a screenshot because I have not seen a triangle of any kind in my address bar.

Trouble with my Apple ID on multiple devices

I am having trouble with my Apple ID when downloading app updates. I go to update my Apps, but the Apple ID for a seperate iPod, that I also sync with this computer, is what appears when the password is requested. I checked the account in Settings > Store and it is the correct one. But everytime I attempt to update my Apps, it has the iPod's Apple ID, which is my father's Apple ID.
In short, when I try to update an app on my iPhone, my Apple ID is not displayed, but my father's iPod Apple ID is displayed with a request for the password. I am not sure what I am doing wrong, but I would appreciate your assistance.

Ok, so you want to remove data (contacts, bookmarks, calendar etc) from other users from your iCloud/Apple ID?
If you want to use your ID for your family because it is the account everybody uses to buy stuff then you only need to ensure that your apple ID is set up in the store (settings-store) and then the users of each device and put their own apple ID in icloud/message/facetime/etc.
To set up your device, in my opinion, it is best to back up to itunes, and then plug your new device into itunes and "set up as ..." and select the backup from your device. This will import all your data/settings and your new device will be set up just like your old one.
I am not certain about using the same payment method for more than one account.

Trouble with getting final cut to capture since new install

I updated my fcp 4.5 to 5.1 and now it doesn't recognize anything I try to firewire my camera jvcgy500 does great on my other mac with 4.5 but doesnt capture at all on my fcp with tiger any suggestions

You'd be much better off asking this question in the Final Cut support forum.

Trouble with flash and image links

Hi
I have been using Dreamweaver for a while, but only for simple websites.
I have now started on a new site, using a template based on css, with two sidebars. I am new to using css, and are "learning by doing"
I wanted to use flash to make navigation buttons in the sidebar to the left, but when I put the flash into the box on the template it does not appear on the page in my browser, or it shows as a white field. So I moved the flash-file to the main part of the page, and it appears there. I have also attached links to the single buttons in the flash,when I made the flash-file, but they do not seem to work at all when I publish the site.
I gave up the project of using flash buttons as navigation and tried to use images instead in the sidebar. The problem then was that I get the blue borders around the linked images. I have found the solution to that of this forum, but as being new to the whole css thing I do understand how I can apply a rule, and where to do it.
My site is here: www.zookjempen.no/test
Here you can see my flash buttons in the middle of the page, but nothing happens when they are clicked. Originally I wanted these buttons on the left, where the white rectangle is, which is the same flashfile.
Could someone please try to explain to me why I get the white field instead of the buttons, and what I need to do to get the buttons to work when clicked?
As I said I am pretty new to css, so plain english would be great.
Thank you.

Thanks. I was thinking of doing screen captures and showing those. But, I fixed the problem.
Maybe it was my particular case, but it was sure screwed up. By recreating the Home page with the links at the top, checking to make sure it was OK, and then duplicating that page for remaining pages, I solved the problem.
Interesting though, even though my "Gallery" page was long ago deleted, if I change the name of a current page back to "Gallery", it gets screwed up again. (This, even though the page is working fine prior to the name change.) That's either my defective site or an iWeb bug.

Trouble with mkinitrd (All of your loopback devices are ...)

Hi all,
I'm trying to rebuild the kernel, and have been somewhat succesful. The only step missing is building the "initrd-image". This I can however not do, as mkinitrd is failing (ERROR: All of your loopback devices are in use!). A bit of googling turned up these postings
http://lists.us.dell.com/pipermail/linu … 07473.html
that I believe is an accurate description of my troubles (lsmod | grep loop returns nothing, and I can not find loop.[o|ko] in /lib/modules/`uname -r`).
The abovementioned postings recommend booting from a live-cd with a stock kernel, mounting whatever neccesary and then doing mkinitrd. I however do not have a live-cd (or arch install cd) available, so I was wondering whether it would be possible to just compile loop.o for the running kernel and the modprob'ing it? Any suggestions would be welcomed.
Thanks,
Mads
PS. I'm also a bit curious as to why loopback support is not compiled as a module in the stock kernel (I believe it was recently updated with pacman). Has something gone wrong in this update, or is this an error of some sort?

Try resetting your router. Unplug it for about 30 seconds, then plug it in again. Turn WiFi off on your iPad, reboot the iPad, turn WiFi on again.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
If that doesn't work, reset network settings. Settings>General>Reset>Reset Network Settings.

Having trouble with downloading apps onto my iOS device(s)

i have been having trouble for the last month id say with downloading and updating apps i have purchased onto my ipad 3 iphone 4s and its really annoying i have contaced apple but inorder for them to help me i would have to pay for each device ttechincal fee which is outragous any help....?

Apple wants you to set your security questions. Select a question from the list and then give an answer. Do not forget the answer(s). You only need to set two, that's why it kicks you out and to the Terms and Conditions page before you get to the third. If you cannot Accept the Terms and Conditions on the device go here > Apple - My Apple ID Manage your Apple ID and set the security questions there. I suggest that you set up a recovery email while you're there. After go back to the device and try again. You may need to answer the security questions to proceed with downloads.

Trouble with Windows7 and Gigabit link on Cisco 3560X switch

Hello,
In my company, we are using Cisco IP Phones 7945G (with 2 gigabit network ports) and Cisco 3560X-48P (1GB ports) switches for our users.
Our client computers are running on Windows 7 SP1 (64bit - Enterprise edition) and are connected behind the IP Phone. We use a "Boradcom
Xtreme Gigabit" onboard network card on the computers. All ports (on the switch site and IP Phone side) and on the network card of the computer are configured in "auto negotiation". Duplex and speed are set to "auto".
We tried now to deploy a new engineering software and we are facing a very strange problem. This means that the engineer software fails to download some files from the server. We are using a flat network, all the servers and computers are on the same network segment with no firewall inbetween.
The firewall and Anti-virus on the computers are configured to allow all incoming/outing connections.
To troubleshoot, I tried to change all the network cables but I still get same result --> download fails.
I connected the client computer directly to the Cisco 3560X switch, without the IP Phone and I get the same result.
I installed a separate network card from INTEL (Intel PRO1000 PT) but I get the same result.
As last test, I have connected to same client computer directly to a Cisco 2960-8TC switch (100Mbit; auto negotiate) and here is working fine. The software successfully downloads all the files from the server.
If I connect the computer behind the Cisco 7945 IP Phone, set the speed and duplex of the PC-Port on the Cisco IP Phone 7945G to "100MBit/full duplex" is also working fine.
Is there any know issue with Windows7 and Gigabit network connections?
Do I need to set any Registry key on my Windows 7?
The firmware version of my Cisco 3560X-48P switch is 12.2(53)SE2; do I need to update it?
The firmware version of the IP Phone 7945G is 9.2.1.
Thanks in advanced for your help.
Marc Hoffmann

Hello, Thanks for your answers. First of all, I have updated the firmware of my Cisco Catalyst 3560X-48P switch to the version 12.2(55)SE5. Unfortunately, this did not solve my problem. As second step, I ran an TDR test on my 3560X switch but I do not get any result. The "Pair status" always says "not completed". Even if I wait for 5 minutes, the status remains at "Not completed". Am I doing something wrong ? To do the TDR test, I use the commande "test cable-diagnostics tdr interface gigabitEthernet 0/XY". For your information, the port gigabitEthernet 0/XY is in a "Connected" status when I run the "show int status" command. Jeff, I think there is no issue on the server side, because if I connect my workstation on a 100MB switch (example Cisco Catalyst 2960-8TC-L) the application works absolutely fine. Also, if I run the application locally on the server, it works fine. As next step, I will connect the workstation directly on our backbone switch and try the same test. Is there perhaps any Registry key in our Windows7 which could cause this trouble? If you have any other ideas or options, please let me know. Thanks a lot, Marc Hoffmann

I'm having trouble with iCloud email on my iOS devices

I'm having trouble accessing all of my e-mail on my iOS devices. On the web, and on the desktop computers, all the mail is there. On my iPhone and iPad, large chunks of mail is missing. I'm have deleted the accounts on the iOS devices and re-enabled them without joy. Any other bright ideas? This just started today.

try this...
go to settings > Mail contacts and calendars> look below accounts you see a section called MAIL
Show: "50 most recent messages" you can change this to be more.
dont know if this will fix it or not so just try iton one of your devices first. if it works, do it on the rest.

I just uploaded the latest IPad software to my IPad and am now having loads of trouble with the device recognizing "online buttons", that is, links, etc.

I just uploaded the latest IPad software to my IPad and am now having loads of trouble with the device recognizing "online buttons", that is, links, etc. what can I do?

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

Trouble with detectin IDS Eagle capture device with JMF

Hi
I'm having trouble detecting my capture card (IDS Eagle model). Is anyone else having the same problem? I tried using the JMStudio tool but the only capture devices detected are the audio ones.
I have installed the WDM driver for this card but jmf doesn't detect it.
Any help will be appreciated. Thank yoU!

Hello Tania,
I think if you look at the source code for AVTransmit2.java, which can be downloaded, this will help you. Make sure you use javasound://8000 as one of the parameters when creating the AVTransmit2 object.
Regards,
James

Unable to capture video using FNC 5.1.1 Quicktime 7.1.2 using Pyro A/V link

Pyro A/V link is the capture device. They say if it works in iMovie HD then it works and they can't help me. It works in iMovie HD but not using Final Cut. I don't know what to do. Do I need quicktime pro? Is there some other driver I need? When I do log and capture it just does the beach ball and then nothing.

I use my camcorder it works with passthru.

Capture devices that work with Final Cut Express

Would any one out there be able to recomend a reasonably priced video capture device that works with FCE other than a video camera? I want to input video and audio from VHS and DVD. I also want to input Audio from cassette and CD.
imac G5 Mac OS X (10.4.4)

I am in a similar situation. All I can say is that the ADS Pyro AV Link works well with iMovie but not with Final Cut Express or Pro so I returned it.
I am waiting for a DataVideo DAC 100, Their web site gives specific instructions as how to use the DAC with FCP so I am hopefull that it will work with FCE.
http://www.datavideo.us/products/dac100_mainpage.htm
The Canopus ADVC 110 has also been recommended on this forum.
http://www.canopus.com/products/ADVC110/index.php

Trouble with Toshiba built-in webcam: "unable to enumerate USB device"

I am running archlinux on a Toshiba Satellite L70-B-12H laptop, and having troubles with the Webcam. *Once in a while*, everything goes well and I get
# lsusb
Bus 004 Device 002: ID 8087:8000 Intel Corp.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 004: ID 04f2:b448 Chicony Electronics Co., Ltd
Bus 003 Device 003: ID 8087:07dc Intel Corp.
Bus 003 Device 002: ID 8087:8008 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
# dmesg
[ 3433.456115] usb 3-1.3: new high-speed USB device number 4 using ehci-pci
[ 3433.781119] media: Linux media interface: v0.10
[ 3433.809842] Linux video capture interface: v2.00
[ 3433.826889] uvcvideo: Found UVC 1.00 device TOSHIBA Web Camera - HD (04f2:b448)
[ 3433.835893] input: TOSHIBA Web Camera - HD as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.3/3-1.3:1.0/input/input15
[ 3433.835976] usbcore: registered new interface driver uvcvideo
[ 3433.835977] USB Video Class driver (1.1.1)
Unfortunately, *most of the time* the camera seems invisible to my system, and I get
# lsusb
Bus 004 Device 002: ID 8087:8000 Intel Corp.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 8087:07dc Intel Corp.
Bus 003 Device 002: ID 8087:8008 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
(note the missing "04f2:b448 Chicony Electronics Co., Ltd" device), and
# dmesg
[ 480.104252] usb 3-1.3: new full-speed USB device number 4 using ehci-pci
[ 480.171097] usb 3-1.3: device descriptor read/64, error -32
[ 480.341235] usb 3-1.3: device descriptor read/64, error -32
[ 480.511375] usb 3-1.3: new full-speed USB device number 5 using ehci-pci
[ 480.578007] usb 3-1.3: device descriptor read/64, error -32
[ 480.748151] usb 3-1.3: device descriptor read/64, error -32
[ 480.918282] usb 3-1.3: new full-speed USB device number 6 using ehci-pci
[ 481.325196] usb 3-1.3: device not accepting address 6, error -32
[ 481.392091] usb 3-1.3: new full-speed USB device number 7 using ehci-pci
[ 481.798926] usb 3-1.3: device not accepting address 7, error -32
[ 481.799166] hub 3-1:1.0: unable to enumerate USB device on port 3
Searching on the web, most results I found lead to this page, where it is said that the problem is due to badly tuned overcurrent protection, and advocated that unplugging and switching off the computer for a little while gets things back into normal. This does not really work for me; the problem seems to occur more randomly, unfortunately with high probability (my camera is available after less than one boot out of ten).
I tried to ensure that the ehci-hcd module is loaded at boot with the ignore-oc option (with a file in /etc/module-load.d/), to no avail.
I also wrote a script which alternatively removes and reloads the ehci-pci driver until my device is found in lsusb. It is sometimes helpful, but usually not. And even when my device is found that way, it can only be used for a while before disappearing again.
Anyway, such a hack is unacceptable... So, my questions are:
is it indeed related to overcurrent protection ?
is there anything else I can try ?
should I file somewhere an other of the numerous bug reports about "unable to enumerate USB device" already existing ?
If of any importance, I am running linux 3.15.7, because at the time I installed my system, I couldn't get the hybrid graphic card Intel/AMD working under 3.16.
Last edited by $nake (2014-10-18 16:29:06)

uname -a
Linux libra 3.9.4-1-ARCH #1 SMP PREEMPT Sat May 25 16:14:55 CEST 2013 x86_64 GNU/Linux
pacman -Qi linux
Name : linux
Version : 3.9.4-1
Description : The linux kernel and modules
Architecture : x86_64
URL : http://www.kernel.org/
Licences : GPL2
Groups : base
Provides : kernel26=3.9.4
Depends On : coreutils linux-firmware kmod mkinitcpio>=0.7
Optional Deps : crda: to set the correct wireless channels of your country
Required By : nvidia
Optional For : None
Conflicts With : kernel26
Replaces : kernel26
Installed Size : 65562.00 KiB
Packager : Tobias Powalowski <[email protected]>
Build Date : Sat 25 May 2013 16:28:17 CEST
Install Date : Sun 02 Jun 2013 15:30:35 CEST
Install Reason : Explicitly installed
Install Script : Yes
Validated By : Signature

Trouble with PYRO a/v link capture device & Tiger

Similar Messages

Maybe you are looking for