Trouble with setting up ethernet on G3 MT

Greetings.
I am able to get good connectivity with my G4 PB (OS 10.4), but not with my G3 MT (OS 9.1). No router being used for either.
Are there any tricks or common mistakes in making this work?
Patch cable or straight-through cable?
I am receiving internet from a wireless provider; the signal is being brought into the house from the antenna via a powerline bridge.
Thanks for your time!

As Don mentioned in passing on your other thread, but did not drive home, the PowerBook G4 is among the Macs that does not care crossover/straight Ethernet cable -- it adapts. Your G3 does NOT adapt, and so the choice of correct cable is essential.
42717- Apple products that require an Ethernet crossover cable
You do you get your Ethernet Address in the G4? PPPoE? DHCP? Manually?
Look in System Preferences > Network > Show: Network Status ; then double click your Ethernet interface and look on the TCP/IP pane.

Similar Messages

  • Im having trouble with setting up my imessage activation do I need credit

    im having trouble with setting up my imessage activation do I need credit

    Please don't post the same question multiple times.

  • Trouble with setting up the network connection

    I am having trouble with setting up my network connection on my new laptop, we use a telecom xtra broadband connection for our windows computers in the house. But when i try to put what i think is the right information in the set up it comes up with "network connection could not be configured"

    Hi,
    you can not connected to sap on 127.0.0.1 ip address it is loopback address for local host.
    instead of give the ip address where sap is running.
    if you running SAP on your standalone PC/laptop then you need to assign one ip address to that host
    use this ip address to connect.
    regards,
    kaushal

  • Trouble with setting up my router...

    I've set up plenty of routers in my life, i've built plenty of computers as well, my knowledge of computers and networking isn't that bad you can say. I was setting up my girlfriends router and was having trouble getting an internet connection. When the modem was hooked up to her computer it was fine, and a website could be accessed. When it is plugged in through the router, you can't access a website. The computer is detecting the connection (Local Area Connection 2 is plugged in) but the interent connection is not being detected. Any suggestions. To avoid this: all wires are assembled correctly! Thanks =)

    I have the same problem here as described above...my router is the linksys wrt150N and my service provider is cox cable...my wireless adapter is intel WiFi link 4965AGN, while the regular connection is through realtek RTL8101E Family PCI-E Fast Ethernet NIC (NDIS 6.0).
    thanks for any solution you can provide...
    DC

  • HT2731 Having trouble with setting billing account

    I'm having trouble setting my billing account with my debit card telling invild security code

    Hi,
    As I understand, you would like to add custom refiner to refinement panel in search.
    From the screenshot, you intended to add vendor name property to search refiner. I cannot find the crawled property in my environment, is it an crawled property converted from custom site column?
    Here is an good article for
    adding refiner in SharePoint search 2013, and it seems there is not much difference from your process. However, here are the things you could check:
    RefinableString00 is in TEXT type, please make sure it matches your vendor name column.
    Please try mapping all crawled properties related to vendor name to RefinableString00 and test the issue again.
    Please try make managed property searchable as well.
    You could also try your process on other default managed property and see if it works.
    Regards,
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected] .
    Rebecca Tu
    TechNet Community Support

  • Trouble with setting Static IP in order to port forward thru 2 routers

    I currently have cable internet connected to one router (Linksys E2000 w/ firmware v1.0.03). That router is connected to another router, a Linksys E3200 w/ firmware v1.0.02. In order to properly forward ports through the E3200, I understand that I need to set up a static IP on that router.
    I've basically followed the steps outlined in this video, but when I enter all the IP addresses for Static IP settings, it won't allow me to access the router's setup page. I try entering the new IP that I've given it (which it tries to direct itself to automatically after I save the settings) and the connection times out. I am able to access the internet otherwise, however. From here I'm forced to do a factory reset on the router and start from square one.
    Anybody have any ideas? I'm getting pretty frustrated and would love to get the ports forwarded so I can get my server properly set up. 
    Solved!
    Go to Solution.

    I apologize, I should have been more specific. I have an ethernet cable connected from a standard port on the E2000 to a standard port on the E3200, which gives it internet access. On a hunch, last night I tried switching the cable to the Internet port on the E3200, but that gave no internet access.
    The two routers are chained because I'm living in a friend's house and he has his own router (the E2000) set up with his own devices. Thus, I have 3 devices of my own connected to the E3200, including a Synology DiskStation NAS, which I would like to forward some ports to. I don't need two LAN subnets-- honestly whatever it takes to forward the ports through the two routers to my NAS would be enough for me. 

  • Trouble with setting up Linux fileserver

    I've done one month of research on the web for this and still no solution, so I have little hope someone in here could help me out.
    I have a linux box with 1TB capacity running perfectly Kubuntu. There are two laptops that need access to this box. I have a samba server on the linux box, and everyone can connect to straight from the Finder without troubles.
    The problem starts when I try to copy files or folders with a " / etc in. The two pseudo solutions I found so far were a filerenamer utility and using dmg files on the server with some kind of a clone app. I didn't try them out myself, because I really need to be able to use the linux box as an external shared harddrive. (push & pull files, and having a share ready for the upcoming TimeMachine space of the several laptops at our company)
    As far as I'm informed it makes no sense to format the linux box drives to HFS (HFS+ is still not supported in the current linux kernel) using AFS instead of samba doesn't solve it either. The problem would be in the samba (or whatever other filetransfer protocol you like). Is that correct?
    On the internet there are no real solutions to this problem, while this might seem a quite important thing to most Apple based companies that want to save money on the X-Serve stuff by setting up a linux server. If there is really no solution available at the moment, then I which to be informed on who might be responsible for solving this problem or who I'd have to address this issue to.
    If anyone might have the same issues or maybe a solution, feel free to post it here.
    Thank you very much in advance.

    Several points.
    First of all, a / is not a valid file name character in Mac OS X, or any Unix flavor that I'm aware of.
    What you're talking about is a fundamental underpinning of the Unix filesystem. That is not going to change any time soon no matter what you do or who you petition.
    That said, it shouldn't even be possible to have such a file on your system right now, so that begs a question right there.
    The problem starts when I try to copy files or folders with a " / etc in.
    While I don't think it's going to make any difference (see my point above), it would be useful to actually indicate what your problem is. Nowhere do you actually say what happens... does the file fail to copy? what about error messages? do the files corrupt when you copy them? does the client crash? or the server?
    it makes no sense to format the linux box drives to HFS
    There is definitely no reason to do this, under any circumstances.
    If anyone might have the same issues or maybe a solution
    Sure - stop trying to use / in filenames. If you have existing files (presumably from some pre-existing environment that didn't prevent their use, implement a renaming session to get rid of them (there are software tools that will do it for you). That is your only viable long-term solution.

  • Trouble with setting correct ACL for publication - EDIT_QUERY error

    *moved from BusinessObjects Integration Kits - SAP
    Hi All, I get an error:  EDIT_QUERY RWI00850 Scheduling document 'xxx' (Id:xxxxxxx) failed for the following users:
    The issue is related to this post http://www.google.dk/url?sa=t&source=web&cd=4&sqi=2&ved=0CDMQFjAD&url=http%3A%2F%2Fforums.sdn.sap.com%2Fthread.jspa%3FthreadID%3D1561142%26tstart%3D-3%26messageID%3D8549187&ei=gq2ATcWNJc3Nsgagraz3Bg&usg=AFQjCNHAFv_8mRsLdK-INp9w_JiuCqS3xA
    We run xi 3.1 fp 3.3
    The publication runs fine, when I add the user to the Admin group, however can't get it to work when I use my custom group with full access ACL assigned at top level to folder, universes, connections and full access ACL to Web Intelligence, infoview, designer appllications.
    Furthermore, when I use my custom ACL I can publicate a wbei report based on efashion. However, if I use the same publication - just switching the content to a webi based on a bex universe, I get the EDIT_QUERY error. Adding my test user to the admin makes it run - so what am I missing???
    Is there a difference in where and how bex based universes are publicated and the efashion universe???
    I've even tried to enable edit objects and edit query in the temporary storage folder, that didn't help either.
    please help!
    BR
    Jess

    Does any one know whether it is a potential bug or it is something I overlooked??
    BR
    Jess

  • Trouble with setting SLD connection of Preview J2EE + ABAP NW04s

    Hi,
    I am trying to connect both J2E and NSP to SLD. J2E has connected correctly.
    In visual admin, I created new entries in Jco RFC provider, (SLDAPI_J2E) the gateway/host = abap system.
    In Sm59 I created new connection to with the program name = SLDAPI_J2E and the connection  looks good.
    But RZ70 will dump regardless of any entry I try. "Could not open rfc connection"
    Any idea?
    Thanks

    Good morning,
    We have exactly the same problem.
    Have you find solution ?
    Regards, Emmanuel

  • HT2731 Trouble with setting up payment info on iTunes iPad

    iTunes won't accept my credit card bank account address details so won't let me purchase - WHY. The address is exactly how the account is set up. Why won't it accept my details. It's so frustrating. I've had the device for about a month but can't buy anything.

    same problem mate have u fixed it yet

  • TROUBLE WITH SETTING CS6

    I installed CS6, deactivated CS4, no icon appears on the desk top.  When I click on the icon in the system tray CS4 loads.  From where is that CS4 coming?

    I was running CS4 under WinXP  and I did erase the serial number, however I
    went into my programs listing and removed CS4 plus ancillary stuff and I
    pinned CS6 & Bridge to my Task Bar.  Everything seems to be working fine.
    I ain't stupid, just slower than most.  :o)

  • Trouble with DNS set up

    Hello !
    I've got a real trouble with my dns configuration... and i can't understand! so, i need some help....
    well, qutie newbie in mac os server, i run in on a G4, and i had not noticed any trouble until i've decided to run open directory as a master with LDAP, wanting to have a kerberos protection for the users.
    Kerberos doesn't want to play with me !
    I've been in console mode to have a look, and, actually i've seen this :
    "Oct 17 11:31:08 wakan servermgrd: servermgr_dns: no name available via DNS for 192.168.0.109
    Oct 17 11:31:08 wakan servermgrd: servermgr_dns: no reverse DNS entry for server, various services may not function properly"
    Ok... my DNS has a trouble... but i don't know how to fix it ! Is there anybody in this world who can help me?
    I don't want to have a real DNS for my little server... but i understand that my config is not good. I can understand that having a caching DNS can improve the quality of my config, and, in other hand that it is necessary for having the services of OSX server in an effeciant way, but i don't know the way and the parameters i've to put in my config to fix it.
    Now, just some words on my config...
    First, i've got an adress provided by my FAI (the frenchy workd for ISP, i think) is "193.252.209.135". This adress is set on a d-link modem router via PPOE. The DNS of my provider (wanadoo.fr) are 80.10.246.1 and 80.10.246.132.
    After this there is my G4 With mac osX server.
    • en0, the "extenal gate" and the internal ethernet on the computer is plug on the modem with the adress "192.168.0.109". the router is set on "192.168.0.1". the dns are 80.10.246.1 and 80.10.246.132.
    • en1, the "internal gate" for the network, an PCI card in the computer, has the parameters : adress "192.168.3.1", subnet "255.255.255.0", router "192.168.3.1". no dns records. (no VPN service for the moment). After this, i've a switch for the macs behind the server. (without any link agregation)
    All those parameters have been set by the gateaway assistant.
    And now the parameters inside the admin server :
    DHCP : en1 - adress from 192.168.3.2 to 192.168.3.254, name 192.168.3. no static card. Router 192.168.3.1. No name for domaine by defaut, name servers 80.10.246.1 and 80.10.246.132 No LDAP, no WINS.
    DNS : No zone transfert, recursivity is ON. No zone records.
    NAT : set on full, Transfert and Network Address Translation.
    When i've been on the terminal, i had those information:
    "wakan:~ st$ sudo changeip -checkhostname
    Password:
    Primary address = 192.168.0.109
    Current HostName = wakan.local
    The DNS hostname is not available, please repair DNS and re-run this tool."
    All my "main" services are working fine (AFP, Firewall, DHCP, DNS, Update) Open Directory is running without Kerberos. By the way, all the macs after the G4server can have a corect access to internet, and share information via LDAP of Open Directory, but i've to say that, a couple of days later, a friend of mine, who has a PC computer, can't have a DHCP dynamic address when he plug on my little network. I think that it is an other trouble, and i've decided to have e look to this later... but if someone knows how to resolve it...
    So here begins the nightmare for me... so if anybody can help me... i realy need some help to fix this mystery!!!
    Special thanks!

    As the router modem is already doing NAT why use NAT in the server?
    If you want to use OpenDirectory and other services you should/need to set up the DNS correctly using the server's private IP (and others in the same range the server is setup with). The domainname used internally can be different than your public one.
    And then use the server as the only DNS for you LAN clients and the server itself. Forwarders (your ISP DNSes) in /etc/named.conf usually speeds up lookups of external addresses (also turning off IPv6 can help that too).

  • Having trouble with the ethernet cable

    Hello-
    All of the sudden the ethernet cable I have been using for my MacBook Pro seems to be causing trouble with my streaming, especially when watching live online streams like from CBS New.com, MSNBC, etc. I had not had any trouble until recently but when I push the ethernet cable in a little bit the stream seems to pick up. This also did happen the last time I installed the latest Flash update. When I do the Software Update, it goes OK, it just seems to be the live video streams.
    I thought I would get a new ethernet cable since I do not know how to hook up my Airport Extreme with the odd set up where I am staying.
    Is there a better kind of ethernet cable or does it matter what kind I get? any recommendations on a good ethernet cable (brand) I should try?
    I would uninstall the latest Flash update, but every time I mess around with Flash it causes trouble, but not the kind of trouble I am having now.

    CanaDuke wrote:
    Moved the AEBS (g) downstairs
    That's probably what caused your problems.
    Here are my questions:
    1) Would replacing the AEBS (g) with an Express (n) solve the problem?
    No.
    The weakness is in the connection between the main base station and the remote (in this case the AEBS (g).
    If you got an Airport Express 802.11n, it would improve the connectivity if it operated in 802.11n mode. However as you have none-802.11n devices which use wireless (ie the iPhones) then you would need to operate in 802.11g mode and therefore the weakness would still be there.
    2) Would ADDING an Express (n) be better?
    See above.
    If everything was 802.11n then yes, otherwise no.
    3) Would we be better off buying the wireless adapter for the xbox, rather than plugging it in with ethernet?
    If you moved the AEBS back to its original location then I expect yes it would.
    iFelix

  • I am having trouble with my Mac Mini's ethernet connection.   Defining a new network interface shows no ethernet adaptor.  Reloading SL from DVD repaired.  But SL update lost ethernet again.  Will Lion Fix?

    I am having trouble with my mac mini ethernet.  It had been working for weeks after an update to SL 10.6.8.
    Once it went out and i repaired it by defining a new connection from System Preferences ->Network->(left panel service, +).
    But yesterday, after a power up.  my ethernet was not working again. I tried this old trick to repair it, but the interface choices
    listed for '+' a new service did not include Ethernet any more.  And the Utilities->System Profiler->Ethernet Cards shows
    no ethernet available.
    As a last ditch effort i reloaded my original SL from DVD.  (I think it was version 10.6.4 but i could be mistaken on the version).
    The ethernet worked!  But KeyNote wasn't going to work because apparently the version i purchased depends on 10.6.8.
    So I upgraded again to SL 10.6.8 (Plus some other updates like AirPort which i don't use).
    Now the Ethernet is not working again.  I see the same symptoms as before with the Ethernet seeming not installed.
    Is this a problem seen by others?
    Would going to Lion fix the problem?
    Could AirPort actually be the culprit and not SL?
    If i stay with my original SL, would i need to repurchase a version of KeyNote for the older version of SL?

    Have you reset the SMC?
    Shut down the computer.
    Unplug the computer's power cord.
    Wait fifteen seconds.
    Attach the computer's power cord.
    Wait five seconds, then press the power button to turn on the computer.
    While you're at it, resetting the PRAM won't hurt anything and 'might' help is SMC reset didn't work (PRAM does some port control):
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.
    Something else you might try .... you don't say how you're updating to 10.6.8, however, if you're using Software Update, you might try downloading the 10.6.8 combo update, which contains all updates to 10.6. Sometimes, Software Update doesn't work quite right, and installing the combo update fixes that. Download the update from Apple's download site at http://support.apple.com/downloads/ , using Disk Utility repair permissions, apply the combo update, then repair permissions again.

  • I am an iPad novice and whilst I have managed to set up my personal email, I have having trouble with my business email in that I can receive emails, but am unable to send and the message says 'this email address has been rejected by server'

    I am an iPad novice and whilst I have managed to set up my hotmail account on the iPad - I ham having trouble with my business email (I can receive emails, but cannot send and it says' email rejected by server'

    That sounds like a settings issue to me. Check with your IT depatment to make sure you have it configured properly.

Maybe you are looking for

  • Removing white border around applet in browser?

    Greetings All, My applets are surrounded by a white border in Netscape and IE. Can I get rid of it so that the applet goes from edge to edge in the browser control? (Looks like default 5 pixel Hgap is in force, is this the case, and if so can it be o

  • E 71 screen or software problem

    E 71 screen is doing intermitant colour saturation, the screen can brighten up and lose it homescreen colour . at times the screen becomes unuseable.then will revert to everthing is fine. have reinstalled lastest updates. was wondering if this was a

  • Dynamic coloring of rows using FM (Reuse_alv_grid_display.)

    I need to color the rows depending on the condition dynamically . I am using FM Reuse_alv_grid_display for ALV . I have the code using Oops Concept, But i need to know how can we do using the Function Module. Please Clarify

  • Syncing starts, then after a minute or two stops...

    Apple TV software version 1.1. iTunes 7.6 on a Vista Home Premium PC. Wireless connection to a Linksys WRT54G router. Apple TV shows up in iTunes no problem. Able to view YouTube movies on Apple TV. All seems to be ok, but... I begin syncing, see pro

  • Is this possible? 2 iTunes library 1 on HDD 1 on a NAS?

    At the moment I have all my library video, music, TV shows together and it's becoming too big for my internal iMac HDD. What I was thinking was having the video and TV shows in a seperate library on my NAS to save storage space. Is this possible? The