Trouble with wireless n and smb shares

I have a bit of a per-plexer here.
I have a personal mac that up until a little while ago, ran 1.5.8 flawlessly for six months since i had it.
This included a lot of mounting my windows 7 file server and watching movies or listening to music over wireless G. Every night in fact I would fall asleep to a movie, then wake up and play some music from my music folder on the same server.
The battery would die nightly of course. Morning, charge it up with some music on.
I picked up a copy of snow leopard upgrade for 30 bucks when it was released or there about and installed it. Went fine and I continued happily using the machine for about 2 months.
Then I bought a belkin wireless N gigabit router, to replace my wrt54g. It worked alright and I continued my daily/nightly routine, watch a movie, sleep, listen to music.
However the first morning, and every morning subsequently there after I have run in to a pain-in-the-butt problem.
I awoke to find, like always, my server shares still mounted (or at least they appeared to be). But opening any of them would present a blank finder window, like no files were available.
Unmounting and re-mounting the shares would fail, with a message saying unable to connect to the PC.
So, what do you do next? I reboot. My programs close, the dock, finder, my background turns to the blue solid.
System stops re-booting... it sits here, with a plain cursor and I am unable to do anything but hard-power it off.
After a hard-reboot,everything functions normally until it hibernates or sleeps with the samba shares.
I took the router back and got a dlink n/gigabit router instead, cussing out belkin on my way to the store. No change!
So I reinstalled (I didn't even archive, i just blew it away) - installed 10.5.8 again, upgraded to SL, and connected to my wireless. I can still reproduce the issue.
So, i'm bummed, i've tried a lot of things I wont bother listing here but one more important detail i wanted to add is:
I work at a company that has blanket wireless b/g coverage using multiple access points and a controller to do load balancing and access point switching.
Recently, we got a few N access points from the provider and I set them up around the office in a new, isolated SSID on the subnet i do my work on. Using WPA2 Psk, like at home.
So, now to be fair I've got a slightly-newer mac at the office, same unibody but late 2009 instead of early 2009 (sd slot instead of express slot). I threw SL on it, and connected to the new SSID i setup and finally connected to our netapp and left for the night.
Come in in the morning and I can reproduce the issue on the work mac.
So, two different macs, 2 very different N wireless networks and 2 different file server platforms. But same prob, **** thing chokes overnight.
I have been able to reproduce this issue with a slough of late 2009 macs at the office now, as I handed out the SSID key to those with SL as my unwitting test subjects. Everyone's coming up with the same problem.
Has anyone out there run in to this? It's such a huge issue i'm surprised i can't find anymore information about it!
Thanks,
Josh

I took a look at the logs and copy and pasted a lot, these are a few before and many from AFTER the hibernation last night.
10-04-15 12:23:59 AM kernel hibernate image path: /var/vm/sleepimage
10-04-15 12:23:59 AM kernel sizeof(IOHibernateImageHeader) == 512
10-04-15 12:23:59 AM kernel Opened file /var/vm/sleepimage, size 2147483648, partition base 0xc805000, maxio 400000
10-04-15 12:23:59 AM kernel hibernate image major 14, minor 2, blocksize 512, pollers 5
10-04-15 12:23:59 AM kernel hibernateallocpages flags 00000000, gobbling 0 pages
10-04-15 12:23:59 AM kernel NVEthernet::setLinkStatus - Valid but not Active
10-04-15 12:23:59 AM kernel AirPort: Link Down on en1. Reason 8 (Disassociated because station leaving).
10-04-15 12:23:59 AM kernel System SafeSleep
10-04-15 6:52:18 AM kernel hibernatepage_listsetall start
10-04-15 6:52:18 AM kernel hibernatepage_listsetall time: 101 ms
10-04-15 6:52:18 AM kernel pages 270008, wire 57222, act 56136, inact 190, spec 78, zf 0, throt 0, could discard act 30534 inact 16602 purgeable 6519 spec 102727
10-04-15 6:52:18 AM kernel hibernatepage_listsetall found pageCount 113626
10-04-15 6:52:18 AM kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
10-04-15 6:52:18 AM kernel IOHibernatePollerOpen(0)
10-04-15 6:52:18 AM kernel writing 111988 pages
10-04-15 6:52:18 AM kernel image1Size 126571008
10-04-15 6:52:18 AM kernel PMStats: Hibernate write took 3775 ms
10-04-15 6:52:18 AM kernel all time: 3775 ms, comp time: 767 ms, deco time: 0 ms,
10-04-15 6:52:18 AM kernel image 226658304, uncompressed 458993664 (112059), compressed 223746576 (48%), sum1 44b2f2dc, sum2 b54e1f71
10-04-15 6:52:18 AM kernel hibernatewriteimage done(0)
10-04-15 6:52:18 AM kernel sleep
10-04-15 6:52:18 AM kernel Wake reason = PWRB
10-04-15 6:52:18 AM kernel System Wake
10-04-15 6:52:18 AM kernel Previous Sleep Cause: 5
10-04-15 6:52:18 AM kernel en1: 802.11d country code set to 'X0'.
10-04-15 6:52:18 AM kernel en1: Supported channels 1 2 3 4 5 6 7 8 9 10 11 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
10-04-15 6:52:18 AM configd[14] network configuration changed.
10-04-15 6:52:18 AM configd[14] setting hostname to "hostname.local"
10-04-15 6:52:19 AM kernel NVEthernet::setLinkStatus - Valid but not Active
10-04-15 6:52:19 AM kernel en1: 802.11d country code set to 'US'.
10-04-15 6:52:19 AM kernel en1: Supported channels 1 2 3 4 5 6 7 8 9 10 11 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
10-04-15 6:52:20 AM kernel Auth result for: 00:24:01:f3:01:5a MAC AUTH succeeded
10-04-15 6:52:20 AM kernel AirPort: Link Up on en1
10-04-15 6:52:20 AM kernel AirPort: RSN handshake complete on en1
10-04-15 6:52:22 AM configd[14] network configuration changed.
10-04-15 6:52:22 AM configd[14] setting hostname to "hostname.domain"
10-04-15 6:52:27 AM Firewall[407] krb5kdc is listening from :::88 proto=6
10-04-15 6:52:27 AM Firewall[407] krb5kdc is listening from 0.0.0.0:88 proto=6
10-04-15 6:52:40 AM ntpd[310] time reset +0.219956 s
10-04-15 6:53:36 AM [0x0-0x25025].org.mozilla.thunderbird[839] Warning: unrecognized command line flag -foreground
10-04-15 6:53:38 AM WindowServer[423] kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
10-04-15 6:53:38 AM com.apple.WindowServer[423] Thu Apr 15 06:53:38 pluto.sunlab WindowServer[423] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
10-04-15 6:55:34 AM kernel smbfssmblookup: smbfssmbqpathinfo error = 60
10-04-15 6:55:34 AM kernel smbfssmblookup: smbfssmbqpathinfo error = 60
10-04-15 6:55:34 AM kernel smbfssmblookup: smbfssmbqpathinfo error = 60
10-04-15 6:55:34 AM kernel smbfssmblookup: smbfssmbqpathinfo error = 60
10-04-15 6:55:34 AM kernel smbfssmblookup: smbfssmbqpathinfo error = 60
10-04-15 6:55:34 AM kernel smbfssmblookup: smbfssmbqpathinfo error = 60

Similar Messages

  • Troubles with wireless keyboard and iMac

    My iMac won't recognize most of the keys on my wireless keyboard. Only several of the function keys seem to work. I've even tried replacing it with a new wireless keyboard, which worked to type in the pairing codes but also wouldn't enter any text into the password field. Since I'm stuck at the login screen and can't enter my password, I can't access any of the software troubleshooting programs that apple support recommends. I just ran an update several days ago. Could that have caused troubles?

    1) You need to go into more detail as to the trouble with the wireless keyboard
    2) Why can't you get a USB one? You can't order one online? Borrow one from someone?
    Without some kind of text entry to enter the password this is going to be difficult.

  • Mac mini first start up trouble with wireless keyboard and magic mouse

    Do you need to use a USB keyboard and mouse for your first mac mini start up? I've just fired it up for the first time and got a strange start up screen. The icon looks like a battery compartment with a green switch with an arrow pointing up. I've read all of my manuals and can not find anything to help me. Any ideas??

    Yes you need to use a wired keyboard.

  • Trouble With Opening InDesign and now Photoshop and Illustrator

    First off I apologize if this isn't in the correct section. I couldn't find a section specific to my problem since it involves multiple aspects of Adobe products. I was having trouble with InDesign, it kept crashing. So I followed all of the advice I could find on the forums about deleting the preferences and cache information in the Library folder, and that didn't seem to make a difference. So then I thought maybe it needed an update, so I logged into Adobe Application Manager and sure enough, it did. So I clicked on "download" and it stalled there too. Then the manager became unresponsive. I couldn't cancel the update or log out or anything. So then I saw in the forum someone suggested the Adobe Creative Cloud Cleaner Tool if your manager becomes unresponsive. I ran that and then shut my computer off. When I turned it back on, InDesign started working BUT my Photoshop is completely gone from my system (I never messed with it in the first place since I wasn't having any trouble with it.) And the when I tried to click on Illustrator it said "Do you want to begin your trial?" Huh?
    I have had a subscription since 2012, why on earth would it suddenly think that I no longer should have access to these programs? If I log on to my Adobe account it shows my subscription and that it's up to date (last payment was April 5, 2015). The versions I was using were the CS versions that I had downloaded directly from Adobe and when I used to have any trouble or when I got a different computer I could just log into my account and then redownload them. They are no longer showing under my products, so I can't figure out what on earth is going on. The website has changed since the last time I downloaded them, so that partly could be me, but I thought they would at least be showing up under products. I contacted Adobe support and the first person I talked to on chat said "this is clearly a technical issue I am transferring you to someone better suited for this," but that's all he said. And I haven't heard from anyone since so I thought I'd make a topic and see if anyone else out there has had a similar problem.

    The versions I am using are the CS6 versions.*

  • Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T

    Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
    I am having trouble making outgoing call or answering incoming call.
    When I try to call out from my IP 7961 phone, it fails with the message "unknown number".
    For incoming call, it rings but when I pick up the call nothing happens,
    Put the receiver back on hook, the phone carries on ringing. I am in UK
    and just trying to set up test system with one analogue line. Any help will
    be most appreciated. My config of the 2811 router is posted below. All calls ineternally works fine.
    Thank you for your help.
    hostname Test-CME
    ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 10.10.10.1 10.10.10.10
    ip dhcp excluded-address 10.139.139.1 10.139.139.10
    ip dhcp pool host
    network 10.10.10.0 255.255.255.0
    default-router 10.10.10.1
    option 150 ip 10.10.10.1
    ip dhcp pool data
    network 10.139.139.0 255.255.255.0
    default-router 10.139.139.1
    dns-server 10.139.139.5
    voice-card 0
    no dspfarm
    voice service voip
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    h323
    sip
    header-passing
    registrar server expires max 3600 min 3600
    interface FastEthernet0/1
    no ip address
    no ip mroute-cache
    duplex auto
    speed auto
    no shut
    interface FastEthernet0/1.2
    description ** Data VLAN **
    encapsulation dot1Q 2
    ip address 10.139.139.1 255.255.255.0
    interface FastEthernet0/1.3
    description ** Voice VLAN **
    encapsulation dot1Q 3
    ip address 10.10.10.1 255.255.255.0
    ip http server
    ip http authentication local
    no ip http secure-server
    ip http path flash:
    tftp-server flash:S00104000100.sbn
    tftp-server flash:TERM41.7-0-3-0S.loads
    tftp-server flash:term61.default.loads
    tftp-server flash:term41.default.loads
    tftp-server flash:CVM41.2-0-2-26.sbn
    tftp-server flash:cnu41.2-7-6-26.sbn
    tftp-server flash:Jar41.2-9-2-26.sbn
    tftp-server flash:term70.default.loads
    tftp-server flash:term71.default.loads
    tftp-server flash:cnu70.2-7-6-26.sbn
    tftp-server flash:Jar70.2-9-2-26.sbn
    tftp-server flash:TERM70.7-0-3-0S.loads
    tftp-server flash:CVM70.2-0-2-26.sbn
    control-plane
    voice-port 0/3/0
    connection plar opx 202
    caller-id enable
    dial-peer voice 1 pots
    incoming called-number .
    destination-pattern 9T
    port 0/3/0
    telephony-service
    load 7914 S00104000100
    load 7941 TERM41.7-0-3-0S
    load 7961 TERM41.7-0-3-0S
    load 7970 TERM70.7-0-3-0S
    max-ephones 20
    max-dn 40
    ip source-address 10.10.10.1 port 2000
    calling-number initiator
    service phone videoCapability 1
    system message MKC CME
    url services http://10.10.10.1/voiceview/common/login.do
    url authentication
    http://10.10.10.1/voiceview/authentication/authenticate.do
    time-zone 21
    date-format dd-mm-yy
    voicemail 600
    max-conferences 8 gain -6
    call-forward pattern .T
    call-forward system redirecting-expanded
    moh music-on-hold.au
    web admin system name admin secret 0 test
    dn-webedit
    time-webedit
    transfer-system full-consult dss
    transfer-pattern 9.T
    secondary-dialtone 9
    create cnf-files
    ephone-dn 1 dual-line
    number 201
    label 201
    description Sarah
    name Sarah
    ephone-dn 2 dual-line
    number 202
    label 202
    description Vitthal
    name User2 Vitthal
    ephone-dn 3 dual-line
    number 203 secondary
    label 203
    description Neil
    name User3 Neil
    ephone 1
    video
    username "user1" password 201
    mac-address 0018.18EE.947F
    type 7961 addon 1 7914
    button 1:1
    ephone 2
    video
    username "user2" password 202
    mac-address 0018.18BB.B973
    type 7941
    button 1:2
    ephone 3
    video
    username "user3" password 203
    mac-address 0018.1885.6BA2
    type 7970
    button 1:3

    Hi
    Please find enclosed debug attachment for voice ccapi and ephone. First, I called from outside. Extension 202 rings but when I answered on extension 202 nothing happens. Replace the rceiever and the pone starts ringing again.Second step. I tried to call out by dialing 9 and then number but after a while phone displays unknown number.
    Thank you for your help.
    Vitthal

  • Did intel core 2 duo imacs come with wireless mouse and keyboard

    did intel core 2 duo imacs come with wireless mouse and keyboard

    raffdog! wrote:
    i would also like to know if it came with a remote
    Same answer the earlier ones did the later ones did not.

  • HT1657 I rented Trouble with the Curve and haven't it yet and I when I went to watch the movie it tells me the file can not be found -  please help

    I rented Trouble with the Curve and haven't it yet and I when I went to watch the movie it tells me the file can not be found -  please help

    Yes, thank you.  My apologies, I was typing one handed and did not add that. 
    Anyway, I have tried deleting the cache, deleting my pics and then re-syncing, etc. and nothing is working This is very frustrating, as I had no problems up until about 2 weeks ago, and now all of a sudden, I have this issue......UGH!

  • Having trouble with wav files and sample rates

    Hi ,I am having trouble with wav files and sample rates .I have been sent multiple projects on wav as the main instrumental ; I wish to record in 48.000kHz .Now comes the problem.When I try to change the project to 48k It seems to pitch up the track.I can't have them send the logic/project file as most have outboard synths,different plug ins etc.This particular case the producer has recorded the synth task in 41.000 kHz .My successful outcome would be to be able t create a project file in 48 kHz .And NOT pitch up whne I add the instrumenta wav file .Any help would be gratefully recieved,this is my first post so any mistakes I may have made go easy 

    You'll have to convert the actual synth audio file file that the producer gave you to 48kHz. You can do this in the audio Bin in Logic.

  • I'm having trouble with iTunes synching and accessing the iTunes store.

    I'm having trouble with iTunes synching and accessing the iTunes store.   When synching, the process tops at the back up stage, freezes and I can't close the iTunes window, need to ctrl alt del.   When trying to access the store, the progress bar stops halfway.   I've googled heaps and tried most of the standard answers - unistall, reinstall, etc, now looking for some help please.
    This has only started a few weeks back, after working smoothly for the 2 years of owning the iPhone 3gs.
    Any suggestions will be appreciated, it's getting realy frustrating.
    Cheers for now,
    Marty

    http://support.apple.com/kb/HT1923?viewlocale=en_US
    this worked perfectly for me, with no loss of library! BUT was warned about uninstalling things in the order listed...FYI.

  • Trouble with internal keyboard and touchpad

    Hi,
    Yesterday I just out of nowhere started having some trouble with my keyboard and touchpad on my MacBook Air.
    The problem displayed itself on various ways. One thing was that I couldn't press regulary with the touchpad. When I was pressing one time, it acted like a pressed with two fingers. When I tried to type in my password on the administrator page, some of the keys didn't work at all and some started to act weird. For example when I was pressing the letter B, the "bar" which displayes where you are in the text (don't know the word in English) went backwards, and when I pressed the letter F it went forward. This seemes so weird and also gives me a hope that it might be some setting failure though B stands for backwards and F stands for forward.
    I could log in to the guestpage where I tried to write in "notes". In notes, no letters at all was working, only numbers. When I tried to shut the computer down from the apple symbol I was asked to write administrator name and password. When I tried to mark the name to write it, there wasn't a "bar" but a cross, but on the other hand did it work to write in the password field. But of course not B and F..
    Usualy I'd just press the on/off botton until the computer lockdown, unfortunately the botton doesn't work. So the only thing I could do was to let the battery die and hope that it would start when I recharged it and pressed start, this didn't go as well as I hoped, so now I'm stuck with a dead macbook air.
    Any ideas of what could be the problem or/and any solutions what might do the trick?
    Extremly greatful for any answers

    Yes you need to use a wired keyboard.

  • Trouble with LaCie disk and time machine

    HI everyone,
    I've been having trouble with using time machine to back-up to my 1 TB LaCie drive (purchased 5/12, unfornuately I was dumb and didn't register the drive and no longer have the box with the serial number and there is no serial number on my drive. The only problem I had up until the end of August was that every so often the LaCie drive (using my FW 800 port) would unmount after waking up from sleep.
    The end of August the drive unmounted for no reason while I was on the computer doing a task. Could not get the LaCie drive remounted (rebooting, etc. etc.) To make a long story short, ended up calling apple care who took me through resetting my SMC and PRAM to no avail. Was booted to higher level of support who walked me through trying to repair my drive using the disk utiltiy. When that didn't work, she walked me through erasing and reformatting the LaCie drive and starting a new time machine back-up. Every thing ok until about ten days ago.
    Last week, when I woke my iMac up from sleep, I got an error saying that the disk was not ejected properly and I could not mount the drive. Restarting did nothing, the disk did not  mount. Shutting down and rebooting seemed to solve the problem and the disk was mounted. Every so often I've had the problem with the disk unmounting after waking up from sleep before. So, I changed my energy sleep preferences. At the end of the day when I am done, I'd unmount the LaCie drive before putting the Mac to sleep using the apple menu.
    Today I came in to start my day, plugged the drive in and it would not mount. Tried rebooting nothing. Went into the disk utility, at first the LaCie drive passed the disk verify (6:26:25 and 6:26:38). Then I went into repair disk on the indented drive at 6:27:13, I wasn't sure what it is was doing, thinking that it had hung, I stopped the repair at 6:27:24. Exited disk utility, and the LaCie drive mounted. But I was getting a read only error when I tried to back-up using time machine. So, I went back into disk utility at 6:27:35, when I verified the disk (indented disk), I got an error saying the disk need to be repaired. After several minutes the disk could not be repaired. So, I erased and reformatted the drive. Ran a time machine back-up and it seemed to back-up everything on my hard drive. Just ran another verify disk and it passed.
    Is the drive failing? Have some other back-ups of my documents, my address book, iCal and am going to make a backup of some of my pref files and important e-mail files and am going to do some more back-ups after I am done.
    Have reached out to the women at apple care whom I talked to last August, but don't expect to hear back from her for at least 24 hours.
    Here is my disk utility log
    2013-11-07 06:26:25 -0500: Verifying partition map for “LaCie”
    2013-11-07 06:26:25 -0500: Starting verification tool:
    2013-11-07 06:26:25 -0500: Checking prerequisites
    2013-11-07 06:26:25 -0500: Checking the partition list
    2013-11-07 06:26:25 -0500: Checking for an EFI system partition
    2013-11-07 06:26:25 -0500: Checking the EFI system partition’s size
    2013-11-07 06:26:25 -0500: Checking the EFI system partition’s file system
    2013-11-07 06:26:25 -0500: Checking all HFS data partition loader spaces
    2013-11-07 06:26:25 -0500: Checking Core Storage Physical Volume partitions
    2013-11-07 06:26:25 -0500: The partition map appears to be OK
    2013-11-07 06:26:25 -0500:
    2013-11-07 06:26:25 -0500:
    2013-11-07 06:26:38 -0500: Verifying partition map for “LaCie”
    2013-11-07 06:26:38 -0500: Starting verification tool:
    2013-11-07 06:26:38 -0500: Checking prerequisites
    2013-11-07 06:26:38 -0500: Checking the partition list
    2013-11-07 06:26:38 -0500: Checking for an EFI system partition
    2013-11-07 06:26:38 -0500: Checking the EFI system partition’s size
    2013-11-07 06:26:38 -0500: Checking the EFI system partition’s file system
    2013-11-07 06:26:38 -0500: Checking all HFS data partition loader spaces
    2013-11-07 06:26:38 -0500: Checking Core Storage Physical Volume partitions
    2013-11-07 06:26:38 -0500: The partition map appears to be OK
    2013-11-07 06:26:38 -0500:
    2013-11-07 06:26:38 -0500:
    2013-11-07 06:27:13 -0500: Disk Utility started.
    2013-11-07 06:27:21 -0500: Verifying and repairing partition map for “LaCie”
    2013-11-07 06:27:21 -0500: Starting repair tool:
    2013-11-07 06:27:21 -0500: Checking prerequisites
    2013-11-07 06:27:21 -0500: Checking the partition list
    2013-11-07 06:27:21 -0500: Checking for an EFI system partition
    2013-11-07 06:27:21 -0500: Checking the EFI system partition’s size
    2013-11-07 06:27:21 -0500: Checking the EFI system partition’s file system
    2013-11-07 06:27:23 -0500: Checking all HFS data partition loader spaces
    2013-11-07 06:27:24 -0500: Reviewing boot support loaders
    2013-11-07 06:27:24 -0500: Checking Core Storage Physical Volume partitions
    2013-11-07 06:27:24 -0500: Updating Windows boot.ini files as required
    2013-11-07 06:27:24 -0500: The partition map appears to be OK
    2013-11-07 06:27:24 -0500:
    2013-11-07 06:27:24 -0500:
    2013-11-07 06:27:35 -0500: Verifying volume “LaCie”
    2013-11-07 06:27:35 -0500: Starting verification tool:
    2013-11-07 06:27:35 -0500: Checking file system2013-11-07 06:27:35 -0500: Error: This disk needs to be repaired. Click Repair Disk.2013-11-07 06:27:35 -0500:
    2013-11-07 06:27:35 -0500: Disk Utility stopped verifying “LaCie”: This disk needs to be repaired. Click Repair Disk.
    2013-11-07 06:28:05 -0500:
    2013-11-07 06:28:13 -0500: Verify and Repair volume “LaCie”
    2013-11-07 06:28:13 -0500: Starting repair tool:
    2013-11-07 06:28:13 -0500: Checking file system2013-11-07 06:28:13 -0500: Volume repair complete.2013-11-07 06:28:13 -0500: Updating boot support partitions for the volume as required.2013-11-07 06:35:05 -0500: Stopped by user
    2013-11-07 06:44:56 -0500: Disk Utility started.
    2013-11-07 06:45:20 -0500: Verifying volume “LaCie”
    2013-11-07 06:45:20 -0500: Starting verification tool:
    2013-11-07 06:45:20 -0500: Checking file system2013-11-07 06:45:20 -0500: Checking Journaled HFS Plus volume.
    2013-11-07 06:45:20 -0500: Checking extents overflow file.
    2013-11-07 06:45:20 -0500: Checking catalog file.
    2013-11-07 06:45:59 -0500: Missing thread record (id = 5057741)
    2013-11-07 06:46:06 -0500: Checking multi-linked files.
    2013-11-07 06:46:19 -0500: Checking catalog hierarchy.
    2013-11-07 06:46:38 -0500: Invalid directory item count
    2013-11-07 06:46:38 -0500: (It should be 0 instead of 4)
    2013-11-07 06:46:38 -0500: Invalid volume directory count
    2013-11-07 06:46:38 -0500: (It should be 166840 instead of 166841)
    2013-11-07 06:46:38 -0500: Checking extended attributes file.
    2013-11-07 06:47:05 -0500: Checking multi-linked directories.
    2013-11-07 06:48:10 -0500: Checking volume bitmap.
    2013-11-07 06:48:12 -0500: Checking volume information.
    2013-11-07 06:48:12 -0500: The volume LaCie was found corrupt and needs to be repaired.
    2013-11-07 06:48:12 -0500: Error: This disk needs to be repaired. Click Repair Disk.2013-11-07 06:48:12 -0500:
    2013-11-07 06:48:12 -0500: Disk Utility stopped verifying “LaCie”: This disk needs to be repaired. Click Repair Disk.
    2013-11-07 06:48:12 -0500:
    2013-11-07 06:50:02 -0500: Verify and Repair volume “LaCie”
    2013-11-07 06:50:02 -0500: Starting repair tool:
    2013-11-07 06:50:02 -0500: Checking file system2013-11-07 06:50:02 -0500: Checking Journaled HFS Plus volume.
    2013-11-07 06:50:02 -0500: Checking extents overflow file.
    2013-11-07 06:50:02 -0500: Checking catalog file.
    2013-11-07 06:50:41 -0500: Missing thread record (id = 5057741)
    2013-11-07 06:50:48 -0500: Checking multi-linked files.
    2013-11-07 06:51:02 -0500: Checking catalog hierarchy.
    2013-11-07 06:51:20 -0500: Invalid directory item count
    2013-11-07 06:51:20 -0500: (It should be 0 instead of 4)
    2013-11-07 06:51:20 -0500: Invalid volume directory count
    2013-11-07 06:51:20 -0500: (It should be 166840 instead of 166841)
    2013-11-07 06:51:20 -0500: Checking extended attributes file.
    2013-11-07 06:51:47 -0500: Checking multi-linked directories.
    2013-11-07 06:52:55 -0500: Checking volume bitmap.
    2013-11-07 06:52:56 -0500: Checking volume information.
    2013-11-07 06:52:56 -0500: Repairing volume.
    2013-11-07 06:52:56 -0500: Missing directory record (id = 5057741)
    2013-11-07 06:52:56 -0500: Look for missing items in lost+found directory.
    2013-11-07 06:53:10 -0500: Rechecking volume.
    2013-11-07 06:53:10 -0500: Checking Journaled HFS Plus volume.
    2013-11-07 06:53:10 -0500: Checking extents overflow file.
    2013-11-07 06:53:10 -0500: Checking catalog file.
    2013-11-07 06:53:16 -0500: Incorrect number of thread records
    2013-11-07 06:53:22 -0500: Checking multi-linked files.
    2013-11-07 06:53:35 -0500: Checking catalog hierarchy.
    2013-11-07 06:53:53 -0500: Invalid directory item count
    2013-11-07 06:53:54 -0500: (It should be 5 instead of 6)
    2013-11-07 06:53:54 -0500: Invalid volume directory count
    2013-11-07 06:53:54 -0500: (It should be 166844 instead of 166842)
    2013-11-07 06:53:54 -0500: Invalid volume file count
    2013-11-07 06:53:54 -0500: (It should be 1056326 instead of 1056321)
    2013-11-07 06:53:54 -0500: Checking extended attributes file.
    2013-11-07 06:54:20 -0500: Checking multi-linked directories.
    2013-11-07 06:55:25 -0500: Checking volume bitmap.
    2013-11-07 06:55:26 -0500: Checking volume information.
    2013-11-07 06:55:26 -0500: Repairing volume.
    2013-11-07 06:58:06 -0500: Rechecking volume.
    2013-11-07 06:58:06 -0500: Checking Journaled HFS Plus volume.
    2013-11-07 06:58:06 -0500: Checking extents overflow file.
    2013-11-07 06:58:07 -0500: Checking catalog file.
    2013-11-07 06:58:12 -0500: Incorrect number of thread records
    2013-11-07 06:58:18 -0500: Checking multi-linked files.
    2013-11-07 06:58:31 -0500: Checking catalog hierarchy.
    2013-11-07 06:58:50 -0500: Invalid volume directory count
    2013-11-07 06:58:50 -0500: (It should be 166844 instead of 166842)
    2013-11-07 06:58:50 -0500: Invalid volume file count
    2013-11-07 06:58:50 -0500: (It should be 1056326 instead of 1056321)
    2013-11-07 06:58:50 -0500: Checking extended attributes file.
    2013-11-07 06:59:17 -0500: Checking multi-linked directories.
    2013-11-07 07:00:22 -0500: Checking volume bitmap.
    2013-11-07 07:00:24 -0500: Checking volume information.
    2013-11-07 07:00:24 -0500: Repairing volume.
    2013-11-07 07:03:03 -0500: Rechecking volume.
    2013-11-07 07:03:03 -0500: Checking Journaled HFS Plus volume.
    2013-11-07 07:03:03 -0500: Checking extents overflow file.
    2013-11-07 07:03:04 -0500: Checking catalog file.
    2013-11-07 07:03:09 -0500: Incorrect number of thread records
    2013-11-07 07:03:15 -0500: Checking multi-linked files.
    2013-11-07 07:03:29 -0500: Checking catalog hierarchy.
    2013-11-07 07:03:47 -0500: Invalid volume directory count
    2013-11-07 07:03:47 -0500: (It should be 166844 instead of 166842)
    2013-11-07 07:03:47 -0500: Invalid volume file count
    2013-11-07 07:03:47 -0500: (It should be 1056326 instead of 1056321)
    2013-11-07 07:03:47 -0500: Checking extended attributes file.
    2013-11-07 07:04:14 -0500: Checking multi-linked directories.
    2013-11-07 07:05:19 -0500: Checking volume bitmap.
    2013-11-07 07:05:20 -0500: Checking volume information.
    2013-11-07 07:05:20 -0500: The volume LaCie could not be repaired after 3 attempts.
    2013-11-07 07:05:21 -0500: Volume repair complete.2013-11-07 07:05:21 -0500: Updating boot support partitions for the volume as required.2013-11-07 07:05:21 -0500: Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.2013-11-07 07:05:21 -0500:
    2013-11-07 07:05:21 -0500: Disk Utility stopped repairing “LaCie”: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.
    2013-11-07 07:05:21 -0500:
    2013-11-07 07:09:45 -0500: Disk Utility started.
    2013-11-07 07:11:45 -0500: Preparing to erase : “LaCie”
    2013-11-07 07:11:45 -0500:     Partition Scheme: GUID Partition Table
    2013-11-07 07:11:45 -0500:     1 volume will be erased
    2013-11-07 07:11:45 -0500:         Name        : “LaCie”
    2013-11-07 07:11:45 -0500:         Size        : 999.86 GB
    2013-11-07 07:11:45 -0500:         File system    : Mac OS Extended (Journaled)
    2013-11-07 07:11:45 -0500: Unmounting disk
    2013-11-07 07:11:45 -0500: Erasing
    2013-11-07 07:11:54 -0500: Initialized /dev/rdisk1s2 as a 931 GB HFS Plus volume with a 81920k journal
    2013-11-07 07:11:54 -0500: Mounting disk
    2013-11-07 07:11:54 -0500: Erase complete.
    2013-11-07 07:11:54 -0500:
    2013-11-07 10:38:00 -0500: Disk Utility started.
    2013-11-07 10:38:12 -0500: Verifying volume “LaCie”
    2013-11-07 10:38:12 -0500: Starting verification tool:
    2013-11-07 10:38:14 -0500: Checking file system2013-11-07 10:38:14 -0500: Checking Journaled HFS Plus volume.
    2013-11-07 10:38:14 -0500: Checking extents overflow file.
    2013-11-07 10:38:14 -0500: Checking catalog file.
    2013-11-07 10:38:29 -0500: Checking multi-linked files.
    2013-11-07 10:38:29 -0500: Checking catalog hierarchy.
    2013-11-07 10:38:41 -0500: Checking extended attributes file.
    2013-11-07 10:39:04 -0500: Checking multi-linked directories.
    2013-11-07 10:39:31 -0500: Checking volume bitmap.
    2013-11-07 10:39:32 -0500: Checking volume information.
    2013-11-07 10:39:32 -0500: The volume LaCie appears to be OK.
    2013-11-07 10:39:32 -0500: Repair tool completed:
    2013-11-07 10:39:32 -0500:
    2013-11-07 10:39:32 -0500:

    I just got a call back from the upper level support person at apple care who had been advising me on my trouble with time machine and my LaCie 1 TB FWD. I had sent her much of the same verbiage as I posted here. As some of you have probably figured out, the verdict is that the drive is probably failing. She says this because I have had to do two erase and reformats. She thought that the intermitant problem that I have had with the drive unmounting when my iMac wakes from sleep could be related to the drive failing.
    In the meantime I have a secondary back-up (not using time machine) and the LaCie  1 TB FWD is working for the moment.
    Thanks to all who read all my verbiage.
    And in the meantime, I've learned something. I marked this question as solved. But I'm open to other things to try.
    Message was edited by: njtreehugger minor edits and update

  • TS3999 Help! Trouble with my calendar and icloud.

    I am having trouble with my calendar and icloud.
    Customers send me meeting invites and I can accept them no problem. But if they subsequently change the date or time I get an error message:
    Access to “appointment name” in “Home” in account “iCloud” is not permitted.
    The server responded:
    “403”
    to operation CalDAVWriteEntityQueueableOperation
    sometimes the time changes in my calendar, sometimes it doesn't, and my customers keep getting messages back from icloud 'accepting' the original date, not the changed date!!
    It is driving me an my clients crazy!  any help would be appreciated.

    I had a problem specific to the Calendar on web-based Firefox (PC) Was asked for a separate sign-in I'd never seen before which didn't work. I resolved this by signing out, signing in again.

  • Mac mini setup with wireless mouse and keyboard

    Bought a new mini with wireless keyboard and mouse. Turns on, picks up the mouse and as soon as the registration setup window starts the connection is lost. It never picked up the keyboard. Apple support said it is not possible to set up a new mini with the wireless accessories so go buy wired ones. Is this really true? Is there a way to skip the registration window, install the wireless keyboard and mouse? Has anyone else had this problem?
    If what the phone support guy said is true then I am a very unhappy new Mac purchaser. Nowhere on the Mac mini site or even in the instruction booklet does it say that you have to have the wired accessories and now apparently I'll have to buy two of everything. Total garbage.

    Can you beg/borrow or steal any ("Windows") USB keyboard and mouse?  They should get you going.  You'll only need them for a few minutes when starting up, once.
    "Garbage" doesn't endear yourself when asking for help on an Apple board though!

  • Initial set up with wireless keyboard and mouse!!

    My gods, I set up a mac mini with wireless keyboard and mouse. It stead fastly refused to find the brand new apple wireless mouse. I had to plug a wacom in, in the end to get anywhere. Then it would not find the keyboard, again apple wireless. It did find the keyboard but when it started the pairing just came up with no keyboards were found.
    I struggled in the end and after around 10 minutes blagged the keyboard, I don't know how it just suddenly worked.
    Thinking about this I had the self same problem on a wireless keyboard and mouse for an iMac as well I installed for a friend, it took ages and ages for the computer to discover the two apple devices.
    Am I just unlucky or is there voodoo involved? Luckily I am a seasoned apple user so got there in the end, but if I were a switcher and the very first experience of my new mac was it could not find its own mouse, I would not be impressed.

    I've been using the Apple wireless mouse and keyboard with my Mac mini for about a year.
    I've noticed that whenever the batteries for the two devices are running very low, they may not be recognize by the mini. Other than that, they are fine.

  • OSX 10.8 and SMB Shares with Access Based Enumeration.

    Hello,
    I've been working on a bit of a problem related to some SMB Shares on Windows Server 2012 with Access Based Enumeration with Mac OSX 10.8 & 10.9.
    Basically, we have one network share that mounts for all of our Students & Faculty on campus. Then, based on which security group the user is inside of in Active Directory, they gain access and visibility to different folders. (Basically, if they are members of the graphic design department, they get access to the Graphic Design's folder). All of that is working fine, no problems. From there we have 3 folders that branch off. We have a Distribution, an Open, and a Dropbox folder.
    Distribution is setup as a spot for instructors to have full access, students have read access, They're able to drop files into this locations, to distribute them to their students. This folder is working fine, no problems.
    Open is setup with everyone read/write access across the board. This folder is setup for students to share data to each other, work on projects, etc. This folder is working as intended, no problems.
    Dropbox is the only folder we're having trouble with, i'm assuming because it's settings are the most complex out of the three. The purpose of the drop box is for students to have read/write control over their own content, but not others, and instructors to have read/write over this entire folder.
    Now that I've laid out our Setup, the problem we've encountered, is ONLY occurring inside of the Dropbox folder. When I try to Drag/Drop OR Copy/Paste from another location on the computer into the Dropbox folder, I get a permission error. HOWEVER, if I have a file open, and I click "save as" browse to the dropbox folder, I can save the file into that location without any trouble. Also, on our windows computers, with the same exact users, drag/drop & Copy/Paste work normally.
    Things I've Tried:
    Disabling the .DS_Store - I figured in the drop box, the .DS_Store would be created by the first user who copied a file in, then subsequent users would not have access to the .DS_Store.
    CIFS/SMB1 - I've read that SMB2 can cause some trouble while connecting to SMB Shares, so I tried both connecting via CIFS, and also by forcing back to SMB1, with no fix.
    Am I missing something with this? I've read a lot about people having trouble connecting to SMB Shares, but for us it had not been a problem up until this point. Does anyone know what a possible fix might be for this? I'm sifting through internet searches right now, trying to find a solution, however MOST of the responses I see are regarding the two things I've already tried.
    Any suggestions would be greatly appreciated.
    Thanks!
    iMac, OS X Mountain Lion (10.8.5)

    Just thought I'd post this in case it helps someone. This could be the same problem we have (had) here so try this:
    When it asks for name and password put this in the name field: sharename\name
    So if the share is called "WWW" and your login name is "Bob" you'd put "www\Bob" in the name field and then normal password in the password field.
    Works perfectly for us. I cant remember when it started 10.7 or 10.8 but this was the only solution. Hope it helps someone else!

Maybe you are looking for

  • In Report Painter, need to find out how a field is defined.

    I'm trying to find out how a field used in a current report is defined.  For example, columns 2-13 are monthly columns.  Double clicking on the column name (April), for example, brings up the box "Element Definition: April;$Year.  The Value Field is

  • How do I move my movies from iCloud to my iPad and close iCloud I hate it!,

    How do I move my movies from iCloud to my iPad  i hate iCloud! I Can never watch a movie on the plane unless I move it first!

  • How do I get snow leopard to install on my MBA 1.1

    I seem to have lost my retail snow leopard disc (I have the box, but no disc inside) so I've been trying all my discs from other macs bought from that era with other versions of Snow Leopard (10.6.3, 10.6.6, 10.6.4, etc.).  None of these will install

  • Report Supplier Lead Time - Days

    Hi All, Can anybody give me the characters, key figures, CKF's, RKF's and other fields that are usually used in Supplier Lead Time - Days Report in general irrespective of the requirement.....come up what ever you remember from your side. Thanks All,

  • Multicam clip displays as missing

    I duplicated my event/project to an external drive, but when I work from the external drive my multicam clip lists as missing.  I fixed this once, but I can't remember how. Help please