Troubles with dell vostro 1400

recently buy a dell vostro 1400 with vista, first install ubuntu and then with internet install arch, but something strange happen with arch, the processor fan work too much, ok, runung kde s normal, but with an base install(no X,kde) the fan work at full, use cpudyn/cpufreq to control the speed but happen, with ubuntu not troubles, and even with vista the fan doesn work to much, only when see movies, but with arch even with init3 the fan enouth for me, meybe do something wrong or miss ??
currently my installation use cpudyn.

Is your CPU overheating? I'd install lm_sensors and see how high the temperature is going. You should do this for all three (Ubuntu, Arch, Vista) if you can and compare what the temperatures are. My guess is that the arch install just has a more cautious approach to cooling. If the temperature is staying constantly above 65C then that would be the problem. Try scaling your CPU down further using cpufreq. Check that it's working by doing as root:
cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
This will tell you what your current CPU speed is. If it never goes below maximum then that is the problem.

Similar Messages

  • Dell Vostro 1400 laptop will not boot Zen imaging

    Got a new Dell Vostro 1400 laptop today to find it has problems with
    ZENworks imaging.
    I can pxe boot the laptop and it will attempt to install the imaging
    software from
    the server but fail and present me with the Linuxrc screen.
    Navigating through the options results in a DHCP configuration failed
    error.
    Can anyone point me in the right direction?
    Is there a hotfix available?
    thanks.
    zen_padawan

    zendude;2862314 Wrote:
    > Try to load the driver tg3.ko and see if it works with this driver and
    > you boot from the cd (pxe will not work because you can't get out of
    > linuxrc, actually you might be able to do it, but I found the menu to
    > be really confusing. Go It looks like is a broadcom 59xx series.>
    Code:
    > > # modprobe tg3
    > >
    > If the driver tg3 works then you need to add the newid option in the
    > append section of the isolinux.cfg or linuxrc.config. Check the
    > forums for more info about newid option.
    I have loaded this driver and added the newid=0x14e4 0x1713 but still
    no luck. Still can not ping the Zenworks server or do anything. The
    Network lights stay lit when it tries to obtain an IP address for eth0.
    I read on another site that you need to update the initrd with the new
    tg3.ko driver. I will try this later tonight and see what happens.
    Cheers
    Chadinsky

  • Dell Vostro 1400 problems

    Hello,
    I've recently bought new laptop Vostro 1400 and I have some problems.
    First one is bluetooth. I've installed bluez-utils, as it said here, but my message.log show's nothing, just that bluetooth demon started.
    lsmod
    bluetooth 50148 3 rfcomm,l2cap,hci_usb
    hcitool dev shows only
    Devices:
    That's nothing... How to configure this stuff ?
    Thank you

    zendude;2862314 Wrote:
    > Try to load the driver tg3.ko and see if it works with this driver and
    > you boot from the cd (pxe will not work because you can't get out of
    > linuxrc, actually you might be able to do it, but I found the menu to
    > be really confusing. Go It looks like is a broadcom 59xx series.>
    Code:
    > > # modprobe tg3
    > >
    > If the driver tg3 works then you need to add the newid option in the
    > append section of the isolinux.cfg or linuxrc.config. Check the
    > forums for more info about newid option.
    I have loaded this driver and added the newid=0x14e4 0x1713 but still
    no luck. Still can not ping the Zenworks server or do anything. The
    Network lights stay lit when it tries to obtain an IP address for eth0.
    I read on another site that you need to update the initrd with the new
    tg3.ko driver. I will try this later tonight and see what happens.
    Cheers
    Chadinsky

  • Trouble with Dell display

    I have a Dell LCD display which I have connected to my Macbook with a MiniDisplay Port to DVI converter, and then a DVI cable running to the display. My computer seems to acknowledge the display, but the display reads "Cannot display this video mode, change computer display input to 1360 x 768 @ 60Hz". When I go to System Preferences > Displays > Gather Windows, I can see the settings for the Dell display. They are the correct settings, the same as above.
    Is there anything I am doing wrong or need to change to get the display to work? I would not like to mirror the displays, I would like to have it as an extended desktop.
    Thanks,
    Collin

    Ok I solved it, and I'll post how because I see this issue everywhere on the net since I've been searching and there hasn't been a working solution. The problem is with the display, not the Mac. (Should have known).
    In the Dell's menu, I scrolled to Setup, DVI Settings, and changed "Source" from "Video" to "Auto"
    I now see my apple's background and can use the display as an extended desktop.

  • Having trouble with dell printer and bonjour

    Hi,
    We recently got iMac computers for our office, however we still have a windows computer we need to be able to use to print. I have the printer, a Dell 1320c, installed on my Mac, and it prints just fine.
    I also have Parallels and Windows 7 installed on my Mac. I can print just fine from within Windows (Bonjour was not needed) Curiously, when I print a Windows Test Page from within Parallels, it says that the printer name is the Dell Color Laser 1320c, however, the Printer Model says: HP Color LaserJet 2800 Series PS. I have no clue where that came from, but I wonder if that may be causing a problem.
    Within OS X 10.8.2, I have enabled Printer Sharing to everyone. I turned off sharing in Parallels, though that didn't make a difference.
    On the Windows 7 PC, I have tried to manually add the printer with TCP/IP, but it wouldn't recognize a printer. I installed Bonjour, and was able to install the Dell printer, however, when I print, I get a bunch of pages that starts like this:
    -12345X@PJL JOB MODE=PRINTER
    @PJL SET STRINGCODESET=UTF8
    @PJL COMMENT DATE=12/26/2012
    @PJL COMMENT TIME=17:02:04
    @PJL COMMENT DNAME=Test Page
    @PJL SET JOBATTR="@LUNA...........
    and so on...
    I've tried uninstalling and reinstalling. I saw several posts about disabling bi-directional support, but that didn't work.
    Does anyone have any ideas of what else I could try?? Thank you!

    Hi,
    No, you can't connect direcly from your computer to your printer using network cable. It has USB connection:
        http://www.cnet.com/products/hp-color-laserjet-cp1518/specs/
    I believe your Macbook Pro also hae USB port(s). Please use a cable which is similar to the follwing cable to connect them:
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Trouble with Dell Color 3110cn

    I am not sure if this has happened since I updated 10.6.2 or not, but I keep on getting a network host busy error for every print job I send. Anybody else having these issues?

    Same here. I cannot print to my 3110cn. This has been an issue for me since updating to Snow Leopard. I check Dell's website for OS X drivers for this printer and they haven't been updated since 2007.

  • Dell Vostro 1400 not resuming from pm-hibernate.

    For some reason my laptop won't resume after hibernating with pm-hibernate.
    I have added the resume hook to /etc/mkinitcpio.conf and the swap drive to /boot/grub/menu.lst.
    Is s2disk reports no error when creating image file and the hook is run on next boot but it doesn't work.
    dmesg output:
    PM: Checking image partition /dev/sda6
    PM: Resume from disk failed.
    PM: Starting manual resume from disk
    PM: Resume from partition 8:6
    PM: Checking hibernation image.
    PM: Error -22 checking image file
    PM: Resume from disk failed.
    Any ideas?

    gustaf@myhost:~$ free
    total used free shared buffers cached
    Mem: 2062312 550380 1511932 0 39912 218132
    -/+ buffers/cache: 292336 1769976
    Swap: 2048252 0 2048252
    gustaf@myhost:~$ df -h
    Filesystem Size Used Avail Use% Mounted on
    udev 10M 244K 9.8M 3% /dev
    /dev/disk/by-uuid/295976ce-2dec-40c7-a8ae-499184c1b9ef
    4.6G 1.3G 3.1G 30% /
    none 1007M 24K 1007M 1% /dev/shm
    /dev/sda1 487M 21M 441M 5% /boot
    /dev/sda7 22G 17G 3.9G 81% /home
    /dev/sda8 4.6G 3.6G 851M 81% /usr
    /dev/sda2 25G 13G 13G 49% /mnt/winsys
    /dev/sda5 54G 42G 12G 78% /mnt/windata

  • Dell Vostro 1400 - How to enable wifi?

    I ran this (my wifi chipset is Broadcom, anyway) :
    ifconfig wlan0 up
    And the output was:
    SIOCSIFFLAGS: No such file or directory
    So I followed the guide on this page, and stuck at this part:
    FATAL: Module wl not found
    Any idea?

    Did you download the broadcom driver module from http://aur.archlinux.org/packages.php?ID=19514 ?
    Perhaps this could help with that process: https://wiki.archlinux.org/index.php/AUR
    Last edited by 3]) (2010-11-25 22:32:01)

  • Dell Vostro 1400 fan speed

    I am not able to get lm_sensors to detect the fan speed, so I installed i8kmon and i8kutils and modprobe i8k force=1 to load the module.
    Now the sensor applet tells me that my fan speed for Fan1 is around 27000 RPM and for Fan2 it's around 10000 RPM, while both cores of the CPU are around 50 C.
    I've never thought of monitoring fan speed until today, but the figures just seem way too great...
    I guess I am not doing it the right way. Any suggestions?

    zendude;2862314 Wrote:
    > Try to load the driver tg3.ko and see if it works with this driver and
    > you boot from the cd (pxe will not work because you can't get out of
    > linuxrc, actually you might be able to do it, but I found the menu to
    > be really confusing. Go It looks like is a broadcom 59xx series.>
    Code:
    > > # modprobe tg3
    > >
    > If the driver tg3 works then you need to add the newid option in the
    > append section of the isolinux.cfg or linuxrc.config. Check the
    > forums for more info about newid option.
    I have loaded this driver and added the newid=0x14e4 0x1713 but still
    no luck. Still can not ping the Zenworks server or do anything. The
    Network lights stay lit when it tries to obtain an IP address for eth0.
    I read on another site that you need to update the initrd with the new
    tg3.ko driver. I will try this later tonight and see what happens.
    Cheers
    Chadinsky

  • Trouble with a Dell Printer on a network with PCs.

    I've searched the forum and found only trouble with people getting their files to print on a mac, but I can print, only it's terrible quality while the PCs are printing out high-quality. It's a Dell 5100cn, and I've installed the updated driver from the Dell website, and called them for help, but they said they couldn't help with a Mac problem. I'm connected through an IP address over a wireless connection.
    Has anyone help?
      Mac OS X (10.4.5)  

    It was a simple problem after all. Sadly my hard disc was about to snuff it. I changed disk, reinsalled Tiger and all is as smooth as ever.

  • DELL VOSTRO 3750 with Windows 7 64 bit BOSD

    Hello:
    I have been dealing with BSOD for the last 8 months, but my hardware appears fine.  I thought the problem was related to some wrong DELL drivers for my DELL VOSTRO 3750 with Windows 7 64 bit.  Tried for a few months to solve the problem with DELL
    customer service.  My warranty ran out May 31, 2014.  I had DELL come and replace the network card and the fan because I was having overheating issues and some of the indications from the bluescreen messages seemed to point at the network card.  A
    month after warranty ran out, I was still getting BSOD so I tried uninstalling and reinstalling original drivers from DELL.  Worked fine for a couple of months. Then the BSODs came back again everyday or 2.
    Is there anyone in the Microsoft world that can help? 
    https://www.dropbox.com/s/0ze9z2yduzdnh5u/MEMORY.DMP?dl=0
    Really appreciated,
    Tim

    Hi,
    I checked the link again and it still stay unavailable.
    Please recheck and upload the files again.
    For resolving Blue Screen Errors in Widnows 7, please first take a look at the following article:
    Resolving stop (blue screen) errors in Windows 7
    Best regards
    Michael Shao
    TechNet Community Support

  • Sound stops random on Dell Vostro 220 with Windows 7 Professional

    Can anyone help? This Dell Vostro 220 w Windows 7 Professional "HD" sound goes off randomly. And I have to reboot to recover the sound.

    Your question has nothing to do with Apple products so I'm not sure why you posted it on an Apple forum.  Try a Windows forum or contact Dell support.

  • MTRR allocation problem on Dell Vostro

    Hello good people,
    I am having MTRR messages from kernel and a warning that graphics performance may suffer. I know from the sparse mtrr documentation around that I can set them up as I want and everything should work  but after trying several changes, the only thing I have managed to do it get a horribly slow laptop.
    I am running 64bit Arch on Dell Vostro 3550. I have 6GB ram and a hybrid video card setup with an Intel card and an ATI one. I am using the proprietary Catalyst driver and I also have the intel driver installed.
    Here we go...
    Kernel message.
    $dmesg | grep -i mtrr
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] MTRR variable ranges enabled:
    [ 17.262434] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining
    [ 17.262437] [drm] MTRR allocation failed. Graphics performance may suffer.
    I noticed in /proc/config.gz that I don't have MTRR cleanup enabled by default so I tried adding enable_mtrr_cleanup to the boot line but I still don't get a good mtrr.
    $zgrep MTRR /proc/config.gz
    CONFIG_MTRR=y
    CONFIG_MTRR_SANITIZER=y
    CONFIG_MTRR_SANITIZER_ENABLE_DEFAULT=0
    CONFIG_MTRR_SANITIZER_SPARE_REG_NR_DEFAULT=1
    Now here is the mtrr I would like to repair. Notice that the memory range in reg 0 is 8192MB. Why? Reg 3 should be the range for the intel card since that's the address I get from lspci -vv as you will see. Similary, reg 4 is mapping for the ATI radeon card. According to what I have read, I want to have these as write-combining. The other ranges I have no idea why they are there which complicates my attempts at fixing the mtrr.
    $cat /proc/mtrr
    reg00: base=0x000000000 ( 0MB), size= 8192MB, count=1: write-back
    reg01: base=0x0cb800000 ( 3256MB), size= 8MB, count=1: uncachable
    reg02: base=0x0cc000000 ( 3264MB), size= 64MB, count=1: uncachable
    reg03: base=0x0d0000000 ( 3328MB), size= 256MB, count=1: uncachable
    reg04: base=0x0e0000000 ( 3584MB), size= 512MB, count=1: uncachable
    reg05: base=0x1afe00000 ( 6910MB), size= 2MB, count=1: uncachable
    reg06: base=0x1b0000000 ( 6912MB), size= 256MB, count=1: uncachable
    reg07: base=0x1c0000000 ( 7168MB), size= 1024MB, count=1: uncachable
    Here is the lspci output.
    $lspci -vv
    00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
    Subsystem: Dell Device 04b3
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
    Latency: 0
    Capabilities: <access denied>
    Kernel driver in use: agpgart-intel
    00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 0000e000-0000efff
    Memory behind bridge: f7b00000-f7bfffff
    Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: <access denied>
    Kernel driver in use: pcieport
    00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
    Subsystem: Dell Device 04cd
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 53
    Region 0: Memory at f6400000 (64-bit, non-prefetchable) [size=4M]
    Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
    Region 4: I/O ports at f000 [size=64]
    Expansion ROM at <unassigned> [disabled]
    Capabilities: <access denied>
    Kernel driver in use: i915
    00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
    Subsystem: Dell Device 04b3
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 52
    Region 0: Memory at f7c0a000 (64-bit, non-prefetchable) [size=16]
    Capabilities: <access denied>
    Kernel driver in use: mei
    00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])
    Subsystem: Dell Device 04b3
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at f7c08000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: <access denied>
    Kernel driver in use: ehci_hcd
    00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
    Subsystem: Dell Device 04b3
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 54
    Region 0: Memory at f7c00000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: <access denied>
    Kernel driver in use: snd_hda_intel
    00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: <access denied>
    Kernel driver in use: pcieport
    00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=05, subordinate=06, sec-latency=0
    I/O behind bridge: 0000d000-0000dfff
    Prefetchable memory behind bridge: 00000000f1100000-00000000f11fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: <access denied>
    Kernel driver in use: pcieport
    00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=09, subordinate=0a, sec-latency=0
    Memory behind bridge: f7a00000-f7afffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: <access denied>
    Kernel driver in use: pcieport
    00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=0b, subordinate=0c, sec-latency=0
    Memory behind bridge: f7900000-f79fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: <access denied>
    Kernel driver in use: pcieport
    00:1c.7 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 (rev b5) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=11, subordinate=16, sec-latency=0
    I/O behind bridge: 0000b000-0000cfff
    Memory behind bridge: f6800000-f78fffff
    Prefetchable memory behind bridge: 00000000f0000000-00000000f10fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: <access denied>
    Kernel driver in use: pcieport
    00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
    Subsystem: Dell Device 04b3
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 0: Memory at f7c07000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: <access denied>
    Kernel driver in use: ehci_hcd
    00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
    Subsystem: Dell Device 04b3
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Capabilities: <access denied>
    00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
    Subsystem: Dell Device 04b3
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin B routed to IRQ 49
    Region 0: I/O ports at f0b0 [size=8]
    Region 1: I/O ports at f0a0 [size=4]
    Region 2: I/O ports at f090 [size=8]
    Region 3: I/O ports at f080 [size=4]
    Region 4: I/O ports at f060 [size=32]
    Region 5: Memory at f7c06000 (32-bit, non-prefetchable) [size=2K]
    Capabilities: <access denied>
    Kernel driver in use: ahci
    00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
    Subsystem: Dell Device 04b3
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Interrupt: pin C routed to IRQ 18
    Region 0: Memory at f7c05000 (64-bit, non-prefetchable) [size=256]
    Region 4: I/O ports at f040 [size=32]
    01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler [AMD Radeon HD 6600M Series] (prog-if 00 [VGA controller])
    Subsystem: Dell Device 04cd
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 55
    Region 0: Memory at e0000000 (64-bit, prefetchable) [size=256M]
    Region 2: Memory at f7b20000 (64-bit, non-prefetchable) [size=128K]
    Region 4: I/O ports at e000 [size=256]
    Expansion ROM at f7b00000 [disabled] [size=128K]
    Capabilities: <access denied>
    Kernel driver in use: fglrx_pci
    05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
    Subsystem: Dell Device 04b3
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 50
    Region 0: I/O ports at d000 [size=256]
    Region 2: Memory at f1104000 (64-bit, prefetchable) [size=4K]
    Region 4: Memory at f1100000 (64-bit, prefetchable) [size=16K]
    Capabilities: <access denied>
    Kernel driver in use: r8169
    09:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 (rev 34)
    Subsystem: Intel Corporation Centrino Wireless-N 1030 BGN
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 51
    Region 0: Memory at f7a00000 (64-bit, non-prefetchable) [size=8K]
    Capabilities: <access denied>
    Kernel driver in use: iwlwifi
    0b:00.0 USB controller: Texas Instruments Device 8241 (rev 02) (prog-if 30 [XHCI])
    Subsystem: Dell Device 04b3
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at f7900000 (64-bit, non-prefetchable) [size=64K]
    Region 2: Memory at f7910000 (64-bit, non-prefetchable) [size=8K]
    Capabilities: <access denied>
    Kernel driver in use: xhci_hcd
    Finally, here is the Xorg log.
    $cat /var/log/Xorg.0.log
    [ 22.722]
    X.Org X Server 1.11.4
    Release Date: 2012-01-27
    [ 22.744] X Protocol Version 11, Revision 0
    [ 22.744] Build Operating System: Linux 3.2.2-1-ARCH x86_64
    [ 22.744] Current Operating System: Linux bitlab 3.3.6-1-ARCH #1 SMP PREEMPT Sun May 13 10:52:32 CEST 2012 x86_64
    [ 22.744] Kernel command line: root=/dev/mapper/arch--volume-lvroot ro
    [ 22.744] Build Date: 29 January 2012 03:38:00PM
    [ 22.744]
    [ 22.744] Current version of pixman: 0.24.4
    [ 22.744] Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
    [ 22.744] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    [ 22.744] (==) Log file: "/var/log/Xorg.0.log", Time: Sat May 19 10:29:00 2012
    [ 22.807] (==) Using config file: "/etc/X11/xorg.conf"
    [ 22.807] (==) Using config directory: "/etc/X11/xorg.conf.d"
    [ 22.828] (==) ServerLayout "aticonfig Layout"
    [ 22.828] (**) |-->Screen "aticonfig-Screen[0]-0" (0)
    [ 22.828] (**) | |-->Monitor "aticonfig-Monitor[0]-0"
    [ 22.829] (**) | |-->Device "aticonfig-Device[0]-0"
    [ 22.829] (==) Automatically adding devices
    [ 22.829] (==) Automatically enabling devices
    [ 22.881] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
    [ 22.881] Entry deleted from font path.
    [ 22.882] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
    [ 22.882] Entry deleted from font path.
    [ 22.882] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
    [ 22.882] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
    [ 22.882] Entry deleted from font path.
    [ 22.882] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
    [ 22.882] (==) FontPath set to:
    /usr/share/fonts/misc/,
    /usr/share/fonts/TTF/,
    /usr/share/fonts/Type1/
    [ 22.882] (==) ModulePath set to "/usr/lib/xorg/modules"
    [ 22.882] (II) The server relies on udev to provide the list of input devices.
    If no devices become available, reconfigure udev or disable AutoAddDevices.
    [ 22.882] (II) Loader magic: 0x7ccae0
    [ 22.882] (II) Module ABI versions:
    [ 22.882] X.Org ANSI C Emulation: 0.4
    [ 22.882] X.Org Video Driver: 11.0
    [ 22.882] X.Org XInput driver : 13.0
    [ 22.882] X.Org Server Extension : 6.0
    [ 22.883] (--) PCI:*(0:0:2:0) 8086:0126:1028:04cd rev 9, Mem @ 0xf6400000/4194304, 0xd0000000/268435456, I/O @ 0x0000f000/64
    [ 22.883] (--) PCI: (0:1:0:0) 1002:6741:1028:04cd rev 0, Mem @ 0xe0000000/268435456, 0xf7b20000/131072, I/O @ 0x0000e000/256, BIOS @ 0x????????/131072
    [ 22.883] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
    [ 22.883] (II) "extmod" will be loaded by default.
    [ 22.883] (II) "dbe" will be loaded by default.
    [ 22.883] (II) "glx" will be loaded by default.
    [ 22.883] (II) "record" will be loaded by default.
    [ 22.883] (II) "dri" will be loaded by default.
    [ 22.883] (II) "dri2" will be loaded by default.
    [ 22.883] (II) LoadModule: "extmod"
    [ 22.934] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
    [ 22.935] (II) Module extmod: vendor="X.Org Foundation"
    [ 22.935] compiled for 1.11.4, module version = 1.0.0
    [ 22.935] Module class: X.Org Server Extension
    [ 22.935] ABI class: X.Org Server Extension, version 6.0
    [ 22.935] (II) Loading extension MIT-SCREEN-SAVER
    [ 22.935] (II) Loading extension XFree86-VidModeExtension
    [ 22.935] (II) Loading extension XFree86-DGA
    [ 22.935] (II) Loading extension DPMS
    [ 22.935] (II) Loading extension XVideo
    [ 22.935] (II) Loading extension XVideo-MotionCompensation
    [ 22.935] (II) Loading extension X-Resource
    [ 22.935] (II) LoadModule: "dbe"
    [ 22.935] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
    [ 22.936] (II) Module dbe: vendor="X.Org Foundation"
    [ 22.936] compiled for 1.11.4, module version = 1.0.0
    [ 22.936] Module class: X.Org Server Extension
    [ 22.936] ABI class: X.Org Server Extension, version 6.0
    [ 22.936] (II) Loading extension DOUBLE-BUFFER
    [ 22.936] (II) LoadModule: "glx"
    [ 22.936] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    [ 22.951] (II) Module glx: vendor="Advanced Micro Devices, Inc."
    [ 22.951] compiled for 6.9.0, module version = 1.0.0
    [ 22.952] (II) Loading extension GLX
    [ 22.952] (II) LoadModule: "record"
    [ 22.952] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
    [ 22.957] (II) Module record: vendor="X.Org Foundation"
    [ 22.957] compiled for 1.11.4, module version = 1.13.0
    [ 22.957] Module class: X.Org Server Extension
    [ 22.957] ABI class: X.Org Server Extension, version 6.0
    [ 22.957] (II) Loading extension RECORD
    [ 22.957] (II) LoadModule: "dri"
    [ 22.958] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
    [ 22.965] (II) Module dri: vendor="X.Org Foundation"
    [ 22.965] compiled for 1.11.4, module version = 1.0.0
    [ 22.965] ABI class: X.Org Server Extension, version 6.0
    [ 22.965] (II) Loading extension XFree86-DRI
    [ 22.965] (II) LoadModule: "dri2"
    [ 22.965] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
    [ 22.966] (II) Module dri2: vendor="X.Org Foundation"
    [ 22.966] compiled for 1.11.4, module version = 1.2.0
    [ 22.966] ABI class: X.Org Server Extension, version 6.0
    [ 22.966] (II) Loading extension DRI2
    [ 22.966] (II) LoadModule: "fglrx"
    [ 22.966] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
    [ 23.148] (II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
    [ 23.154] compiled for 1.4.99.906, module version = 8.96.4
    [ 23.154] Module class: X.Org Video Driver
    [ 23.156] (II) Loading sub module "fglrxdrm"
    [ 23.156] (II) LoadModule: "fglrxdrm"
    [ 23.156] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
    [ 23.183] (II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
    [ 23.183] compiled for 1.4.99.906, module version = 8.96.4
    [ 23.192] (II) ATI Proprietary Linux Driver Version Identifier:8.96.4
    [ 23.192] (II) ATI Proprietary Linux Driver Release Identifier: 8.961
    [ 23.192] (II) ATI Proprietary Linux Driver Build Date: Apr 5 2012 23:06:21
    [ 23.192] (++) using VT number 7
    [ 23.195] (WW) Falling back to old probe method for fglrx
    [ 23.260] (II) Loading PCS database from /etc/ati/amdpcsdb
    [ 23.263] (--) Chipset Supported AMD Graphics Processor (0x6741) found
    [ 23.264] (II) fglrx: intel VGA device detected, load intel driver.
    [ 23.264] (II) LoadModule: "intel"
    [ 23.264] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
    [ 23.296] (II) Module intel: vendor="X.Org Foundation"
    [ 23.296] compiled for 1.11.2, module version = 2.17.0
    [ 23.296] Module class: X.Org Video Driver
    [ 23.296] ABI class: X.Org Video Driver, version 11.0
    [ 23.298] ukiDynamicMajor: found major device number 251
    [ 23.298] ukiDynamicMajor: found major device number 251
    [ 23.298] ukiOpenByBusid: Searching for BusID PCI:1:0:0
    [ 23.298] ukiOpenDevice: node name is /dev/ati/card0
    [ 23.298] ukiOpenDevice: open result is 7, (OK)
    [ 23.298] ukiOpenByBusid: ukiOpenMinor returns 7
    [ 23.298] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
    [ 23.300] (II) AMD Video driver is running on a device belonging to a group targeted for this release
    [ 23.301] (II) AMD Video driver is signed
    [ 23.301] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
    [ 23.301] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
    [ 23.301] (II) fglrx(0): pEnt->device->identifier=0x100a450
    [ 23.302] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
    [ 23.302] (II) intel(1): pEnt->device->identifier=(nil)
    [ 23.302] (EE) Screen 1 deleted because of no matching config section.
    [ 23.302] (II) UnloadModule: "intel"
    [ 23.302] (II) Unloading intel
    [ 23.302] (II) fglrx(0): === [xdl_xs111_atiddxPreInit] === begin
    [ 23.302] (II) fglrx(0): PowerXpress: Discrete GPU is selected.
    [ 23.798] (II) fglrx(0): PowerXpress: Diagnostic output from /usr/lib64/fglrx/switchlibGL:
    Switch to AMD
    [ 23.801] drmOpenDevice: node name is /dev/dri/card0
    [ 23.801] drmOpenDevice: open result is 12, (OK)
    [ 23.801] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
    [ 23.801] drmOpenDevice: node name is /dev/dri/card0
    [ 23.801] drmOpenDevice: open result is 12, (OK)
    [ 23.801] drmOpenByBusid: drmOpenMinor returns 12
    [ 23.801] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
    [ 23.801] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
    [ 23.801] (==) fglrx(0): RGB weight 888
    [ 23.801] (==) fglrx(0): Default visual is TrueColor
    [ 23.802] (**) fglrx(0): Option "Tiling" "off"
    [ 23.802] (**) fglrx(0): Option "LinearFramebuffer" "on"
    [ 23.802] (**) fglrx(0): Option "Shadow" "off"
    [ 23.802] (II) fglrx(0): Integrated Graphics Chipset: Intel(R) Sandybridge Mobile (GT2+)
    [ 23.802] (**) fglrx(0): ChipID override: 0x0126
    [ 23.802] (**) fglrx(0): ChipRev override: 9
    [ 23.802] (**) fglrx(0): Chipset: "Sandybridge Mobile (GT2+)"
    [ 23.802] (**) fglrx(0): Relaxed fencing enabled
    [ 23.802] (**) fglrx(0): Wait on SwapBuffers? enabled
    [ 23.802] (**) fglrx(0): Triple buffering? enabled
    [ 23.802] (**) fglrx(0): Framebuffer linear
    [ 23.802] (**) fglrx(0): Pixmaps linear
    [ 23.802] (**) fglrx(0): 3D buffers tiled
    [ 23.802] (**) fglrx(0): SwapBuffers wait enabled
    [ 23.802] (==) fglrx(0): video overlay key set to 0x101fe
    [ 23.802] (II) fglrx(0): Output LVDS1 using monitor section aticonfig-Monitor[0]-0
    [ 23.802] (II) fglrx(0): found backlight control interface /sys/class/backlight/acpi_video1
    [ 23.802] (II) fglrx(0): Output VGA1 has no monitor section
    [ 23.825] (II) fglrx(0): Output HDMI1 has no monitor section
    [ 23.863] (II) fglrx(0): Output DP1 has no monitor section
    [ 23.863] (II) fglrx(0): EDID for output LVDS1
    [ 23.863] (II) fglrx(0): Manufacturer: LGD Model: 2e3 Serial#: 0
    [ 23.863] (II) fglrx(0): Year: 2010 Week: 0
    [ 23.863] (II) fglrx(0): EDID Version: 1.4
    [ 23.863] (II) fglrx(0): Digital Display Input
    [ 23.863] (II) fglrx(0): 6 bits per channel
    [ 23.863] (II) fglrx(0): Digital interface is undefined
    [ 23.863] (II) fglrx(0): Max Image Size [cm]: horiz.: 34 vert.: 19
    [ 23.863] (II) fglrx(0): Gamma: 2.20
    [ 23.863] (II) fglrx(0): No DPMS capabilities specified
    [ 23.863] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
    [ 23.863] (II) fglrx(0): First detailed timing is preferred mode
    [ 23.863] (II) fglrx(0): Preferred mode is native pixel format and refresh rate
    [ 23.863] (II) fglrx(0): redX: 0.613 redY: 0.371 greenX: 0.350 greenY: 0.606
    [ 23.863] (II) fglrx(0): blueX: 0.152 blueY: 0.099 whiteX: 0.313 whiteY: 0.329
    [ 23.863] (II) fglrx(0): Manufacturer's mask: 0
    [ 23.863] (II) fglrx(0): Supported detailed timing:
    [ 23.863] (II) fglrx(0): clock: 76.0 MHz Image Size: 344 x 194 mm
    [ 23.863] (II) fglrx(0): h_active: 1366 h_sync: 1402 h_sync_end 1450 h_blank_end 1564 h_border: 0
    [ 23.863] (II) fglrx(0): v_active: 768 v_sync: 771 v_sync_end 776 v_blanking: 810 v_border: 0
    [ 23.863] (II) fglrx(0): Supported detailed timing:
    [ 23.863] (II) fglrx(0): clock: 51.0 MHz Image Size: 344 x 194 mm
    [ 23.863] (II) fglrx(0): h_active: 1366 h_sync: 1402 h_sync_end 1450 h_blank_end 1564 h_border: 0
    [ 23.863] (II) fglrx(0): v_active: 768 v_sync: 771 v_sync_end 776 v_blanking: 814 v_border: 0
    [ 23.863] (II) fglrx(0): PPCTF156WH4
    [ 23.863] (II) fglrx(0): Unknown vendor-specific block 0
    [ 23.863] (II) fglrx(0): EDID (in hex):
    [ 23.863] (II) fglrx(0): 00ffffffffffff0030e4e30200000000
    [ 23.863] (II) fglrx(0): 00140104902213780a09159d5f599b27
    [ 23.863] (II) fglrx(0): 19505400000001010101010101010101
    [ 23.863] (II) fglrx(0): 010101010101b01d56c650002a302430
    [ 23.863] (II) fglrx(0): 350058c210000019ec1356c650002e30
    [ 23.863] (II) fglrx(0): 2430350058c210000019000000fe0050
    [ 23.863] (II) fglrx(0): 50435446803135365748340a00000000
    [ 23.863] (II) fglrx(0): 00004131960000000001010a202000ef
    [ 23.863] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 23.863] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 23.863] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 23.863] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 23.863] (II) fglrx(0): Not using default mode "320x240" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "400x300" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "400x300" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "512x384" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "640x480" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "640x512" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "800x600" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "896x672" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "928x696" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "960x720" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "700x525" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Not using default mode "1024x768" (doublescan mode not supported)
    [ 23.863] (II) fglrx(0): Printing probed modes for output LVDS1
    [ 23.863] (II) fglrx(0): Modeline "1366x768"x60.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 23.863] (II) fglrx(0): Modeline "1366x768"x40.1 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 23.863] (II) fglrx(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
    [ 23.863] (II) fglrx(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
    [ 23.863] (II) fglrx(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
    [ 23.863] (II) fglrx(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
    [ 23.863] (II) fglrx(0): EDID for output VGA1
    [ 23.887] (II) fglrx(0): EDID for output HDMI1
    [ 23.926] (II) fglrx(0): EDID for output DP1
    [ 23.973] (II) fglrx(0): Output LVDS1 connected
    [ 23.973] (II) fglrx(0): Output VGA1 disconnected
    [ 23.973] (II) fglrx(0): Output HDMI1 disconnected
    [ 23.973] (II) fglrx(0): Output DP1 disconnected
    [ 23.973] (II) fglrx(0): Using exact sizes for initial modes
    [ 23.973] (II) fglrx(0): Output LVDS1 using initial mode 1366x768
    [ 23.973] (II) fglrx(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
    [ 23.973] (II) fglrx(0): Kernel page flipping support detected, enabling
    [ 23.973] (**) fglrx(0): Display dimensions: (340, 190) mm
    [ 23.973] (**) fglrx(0): DPI set to (102, 102)
    [ 23.973] (II) Loading sub module "fb"
    [ 23.973] (II) LoadModule: "fb"
    [ 23.984] (II) Loading /usr/lib/xorg/modules/libfb.so
    [ 24.133] (II) Module fb: vendor="X.Org Foundation"
    [ 24.133] compiled for 1.11.4, module version = 1.0.0
    [ 24.133] ABI class: X.Org ANSI C Emulation, version 0.4
    [ 24.133] (II) Loading sub module "dri2"
    [ 24.133] (II) LoadModule: "dri2"
    [ 24.133] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
    [ 24.133] (II) Module dri2: vendor="X.Org Foundation"
    [ 24.133] compiled for 1.11.4, module version = 1.2.0
    [ 24.133] ABI class: X.Org Server Extension, version 6.0
    [ 24.133] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
    [ 24.133] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
    [ 24.133] (==) fglrx(0): Default visual is TrueColor
    [ 24.133] (**) fglrx(0): Option "DPMS" "true"
    [ 24.133] (==) fglrx(0): RGB weight 888
    [ 24.133] (II) fglrx(0): Using 8 bits per RGB
    [ 24.133] (==) fglrx(0): Buffer Tiling is ON
    [ 24.133] (II) Loading sub module "fglrxdrm"
    [ 24.133] (II) LoadModule: "fglrxdrm"
    [ 24.133] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
    [ 24.133] (II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
    [ 24.133] compiled for 1.4.99.906, module version = 8.96.4
    [ 24.134] ukiDynamicMajor: found major device number 251
    [ 24.134] ukiDynamicMajor: found major device number 251
    [ 24.134] ukiOpenByBusid: Searching for BusID PCI:1:0:0
    [ 24.134] ukiOpenDevice: node name is /dev/ati/card0
    [ 24.134] ukiOpenDevice: open result is 13, (OK)
    [ 24.134] ukiOpenByBusid: ukiOpenMinor returns 13
    [ 24.134] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
    [ 24.135] (**) fglrx(0): NoAccel = NO
    [ 24.135] (**) fglrx(0): ATI 2D Acceleration Architecture enabled
    [ 24.135] (--) fglrx(0): Chipset: "AMD Radeon 6600M and 6700M Series" (Chipset = 0x6741)
    [ 24.135] (--) fglrx(0): (PciSubVendor = 0x1028, PciSubDevice = 0x04cd)
    [ 24.135] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original ATI
    [ 24.135] (--) fglrx(0): Linear framebuffer (phys) at 0xe0000000
    [ 24.135] (--) fglrx(0): MMIO registers at 0xf7b20000
    [ 24.135] (--) fglrx(0): I/O port at 0x0000e000
    [ 24.135] (==) fglrx(0): ROM-BIOS at 0x000c0000
    [ 24.157] (II) fglrx(0): AC Adapter is used
    [ 24.236] (II) fglrx(0): ATI Video BIOS revision 9 or later detected
    [ 24.236] (--) fglrx(0): Video RAM: 1048576 kByte, Type: DDR3
    [ 24.236] (II) fglrx(0): PCIE card detected
    [ 24.236] (--) fglrx(0): Using per-process page tables (PPPT) as GART.
    [ 24.236] (WW) fglrx(0): board is an unknown third party board, chipset is supported
    [ 24.241] (II) fglrx(0): Using adapter: 1:0.0.
    [ 24.248] (II) fglrx(0): [FB] MC range(MCFBBase = 0xf00000000, MCFBSize = 0x40000000)
    [ 24.274] (II) fglrx(0): Interrupt handler installed at IRQ 55.
    [ 24.274] (II) fglrx(0): RandR 1.2 support is enabled!
    [ 24.274] (II) fglrx(0): RandR 1.2 rotation support is enabled!
    [ 24.274] (==) fglrx(0): Center Mode is disabled
    [ 24.274] (II) Loading sub module "fb"
    [ 24.274] (II) LoadModule: "fb"
    [ 24.274] (II) Loading /usr/lib/xorg/modules/libfb.so
    [ 24.274] (II) Module fb: vendor="X.Org Foundation"
    [ 24.274] compiled for 1.11.4, module version = 1.0.0
    [ 24.274] ABI class: X.Org ANSI C Emulation, version 0.4
    [ 24.274] (II) Loading sub module "ddc"
    [ 24.274] (II) LoadModule: "ddc"
    [ 24.274] (II) Module "ddc" already built-in
    [ 24.388] (II) fglrx(0): Finished Initialize PPLIB!
    [ 24.396] (II) fglrx(0): Eyefinity capable adapter detected.
    [ 24.397] (II) fglrx(0): Adapter AMD Radeon 6600M and 6700M Series has 6 configurable heads and 0 displays connected.
    [ 24.397] (==) fglrx(0): PseudoColor visuals disabled
    [ 24.397] (II) Loading sub module "ramdac"
    [ 24.397] (II) LoadModule: "ramdac"
    [ 24.397] (II) Module "ramdac" already built-in
    [ 24.397] (==) fglrx(0): NoDRI = NO
    [ 24.397] (==) fglrx(0): Capabilities: 0x00000000
    [ 24.397] (==) fglrx(0): CapabilitiesEx: 0x00000000
    [ 24.397] (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
    [ 24.397] (==) fglrx(0): UseFastTLS=0
    [ 24.397] (--) Depth 24 pixmap format is 32 bpp
    [ 24.397] (II) LoadModule: "glesx"
    [ 24.458] (II) Loading /usr/lib/xorg/modules/glesx.so
    [ 24.594] (II) Module glesx: vendor="X.Org Foundation"
    [ 24.594] compiled for 1.4.99.906, module version = 1.0.0
    [ 24.594] (II) Loading extension GLESX
    [ 24.606] (II) fglrx(0): [DRI2] Setup complete
    [ 24.606] (II) fglrx(0): [DRI2] DRI driver: i965
    [ 24.606] (II) fglrx(0): Allocated new frame buffer 1408x768 stride 5632, untiled
    [ 24.610] (II) UXA(0): Driver registered support for the following operations:
    [ 24.610] (II) solid
    [ 24.610] (II) copy
    [ 24.610] (II) composite (RENDER acceleration)
    [ 24.610] (II) put_image
    [ 24.610] (II) get_image
    [ 24.610] (==) fglrx(0): Backing store disabled
    [ 24.610] (==) fglrx(0): Silken mouse enabled
    [ 24.610] (II) fglrx(0): Initializing HW Cursor
    [ 24.666] (II) fglrx(0): RandR 1.2 enabled, ignore the following RandR disabled message.
    [ 24.667] (**) fglrx(0): DPMS enabled
    [ 24.667] (==) fglrx(0): Intel XvMC decoder enabled
    [ 24.667] (II) fglrx(0): Set up textured video
    [ 24.667] (II) fglrx(0): [XvMC] xvmc_vld driver initialized.
    [ 24.667] (II) fglrx(0): direct rendering: DRI2 Enabled
    [ 24.667] (WW) fglrx(0): Option "VendorName" is not used
    [ 24.667] (WW) fglrx(0): Option "ModelName" is not used
    [ 24.667] (WW) fglrx(0): Option "Shadow" is not used
    [ 24.667] (WW) fglrx(0): Option "Tiling" is not used
    [ 24.667] (WW) fglrx(0): Option "LinearFramebuffer" is not used
    [ 24.667] (==) fglrx(0): hotplug detection: "enabled"
    [ 24.668] (II) Loading extension ATIFGLRXDRI
    [ 24.668] (II) fglrx(0): doing swlDriScreenInit
    [ 24.668] (II) fglrx(0): swlDriScreenInit for fglrx driver
    [ 24.668] ukiDynamicMajor: found major device number 251
    [ 24.668] ukiDynamicMajor: found major device number 251
    [ 24.668] ukiDynamicMajor: found major device number 251
    [ 24.668] ukiOpenByBusid: Searching for BusID PCI:1:0:0
    [ 24.668] ukiOpenDevice: node name is /dev/ati/card0
    [ 24.668] ukiOpenDevice: open result is 15, (OK)
    [ 24.668] ukiOpenByBusid: ukiOpenMinor returns 15
    [ 24.668] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
    [ 24.668] (II) fglrx(0): [uki] DRM interface version 1.0
    [ 24.668] (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:1:0:0"
    [ 24.668] (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000
    [ 24.668] (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0x7f9e27b95000
    [ 24.668] (II) fglrx(0): [uki] framebuffer handle = 0x3000
    [ 24.668] (II) fglrx(0): [uki] added 1 reserved context for kernel
    [ 24.668] (II) fglrx(0): swlDriScreenInit done
    [ 24.668] (II) fglrx(0): Kernel Module Version Information:
    [ 24.668] (II) fglrx(0): Name: fglrx
    [ 24.668] (II) fglrx(0): Version: 8.96.4
    [ 24.668] (II) fglrx(0): Date: Apr 5 2012
    [ 24.668] (II) fglrx(0): Desc: ATI FireGL DRM kernel module
    [ 24.668] (II) fglrx(0): Kernel Module version matches driver.
    [ 24.668] (II) fglrx(0): Kernel Module Build Time Information:
    [ 24.668] (II) fglrx(0): Build-Kernel UTS_RELEASE: 3.3.6-1-ARCH
    [ 24.668] (II) fglrx(0): Build-Kernel MODVERSIONS: no
    [ 24.668] (II) fglrx(0): Build-Kernel __SMP__: no
    [ 24.668] (II) fglrx(0): Build-Kernel PAGE_SIZE: 0x1000
    [ 24.668] (II) fglrx(0): [uki] register handle = 0x00004000
    [ 24.699] (II) fglrx(0): DRI initialization successfull
    [ 24.699] (II) fglrx(0): FBADPhys: 0xf00000000 FBMappedSize: 0x01028000
    [ 24.699] (II) fglrx(0): Intel display surface mc addr for AMD: 8fce0000
    [ 24.700] (==) fglrx(0): Backing store disabled
    [ 24.700] (II) Loading extension FGLRXEXTENSION
    [ 24.700] (**) fglrx(0): DPMS enabled
    [ 24.700] (II) fglrx(0): Initialized in-driver Xinerama extension
    [ 24.700] (**) fglrx(0): Textured Video is enabled.
    [ 24.700] (II) fglrx(0): GLESX enableFlags = 848
    [ 24.700] (II) fglrx(0): GLESX is enabled
    [ 24.700] (II) LoadModule: "amdxmm"
    [ 24.701] (II) Loading /usr/lib/xorg/modules/amdxmm.so
    [ 24.709] (II) Module amdxmm: vendor="X.Org Foundation"
    [ 24.709] compiled for 1.4.99.906, module version = 2.0.0
    [ 24.709] (II) Loading extension AMDXVOPL
    [ 24.709] (II) Loading extension AMDXVBA
    [ 24.709] XvScreenInit: screen devPrivates ptr non-NULL before init
    [ 24.721] (II) fglrx(0): UVD feature is enabled(II) fglrx(0):
    [ 24.723] (II) fglrx(0): Enable composite support successfully
    [ 24.723] (WW) fglrx(0): Option "VendorName" is not used
    [ 24.723] (WW) fglrx(0): Option "ModelName" is not used
    [ 24.723] (WW) fglrx(0): Option "Shadow" is not used
    [ 24.723] (WW) fglrx(0): Option "Tiling" is not used
    [ 24.723] (WW) fglrx(0): Option "LinearFramebuffer" is not used
    [ 24.723] (II) fglrx(0): X context handle = 0x1
    [ 24.723] (II) fglrx(0): [DRI] installation complete
    [ 24.736] (--) RandR disabled
    [ 24.736] (II) Initializing built-in extension Generic Event Extension
    [ 24.736] (II) Initializing built-in extension SHAPE
    [ 24.736] (II) Initializing built-in extension MIT-SHM
    [ 24.736] (II) Initializing built-in extension XInputExtension
    [ 24.736] (II) Initializing built-in extension XTEST
    [ 24.736] (II) Initializing built-in extension BIG-REQUESTS
    [ 24.736] (II) Initializing built-in extension SYNC
    [ 24.736] (II) Initializing built-in extension XKEYBOARD
    [ 24.736] (II) Initializing built-in extension XC-MISC
    [ 24.736] (II) Initializing built-in extension SECURITY
    [ 24.736] (II) Initializing built-in extension XINERAMA
    [ 24.736] (II) Initializing built-in extension XFIXES
    [ 24.736] (II) Initializing built-in extension RENDER
    [ 24.736] (II) Initializing built-in extension RANDR
    [ 24.736] (II) Initializing built-in extension COMPOSITE
    [ 24.736] (II) Initializing built-in extension DAMAGE
    [ 24.737] ukiDynamicMajor: found major device number 251
    [ 24.737] ukiDynamicMajor: found major device number 251
    [ 24.737] ukiOpenByBusid: Searching for BusID PCI:1:0:0
    [ 24.737] ukiOpenDevice: node name is /dev/ati/card0
    [ 24.737] ukiOpenDevice: open result is 16, (OK)
    [ 24.737] ukiOpenByBusid: ukiOpenMinor returns 16
    [ 24.737] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
    [ 25.513] (II) AIGLX: Loaded and initialized OpenGL driver(II) GLX: Initialized DRI GL provider for screen 0
    [ 25.597] (II) fglrx(0): Enable the clock gating!
    [ 25.597] (II) fglrx(0): Setting screen physical size to 361 x 203
    [ 25.834] (II) config/udev: Adding input device Power Button (/dev/input/event6)
    [ 25.834] (**) Power Button: Applying InputClass "evdev keyboard catchall"
    [ 25.834] (II) LoadModule: "evdev"
    [ 25.834] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.840] (II) Module evdev: vendor="X.Org Foundation"
    [ 25.840] compiled for 1.10.99.902, module version = 2.6.0
    [ 25.840] Module class: X.Org XInput Driver
    [ 25.840] ABI class: X.Org XInput driver, version 13.0
    [ 25.840] (II) Using input driver 'evdev' for 'Power Button'
    [ 25.840] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.840] (**) Power Button: always reports core events
    [ 25.840] (**) Power Button: Device: "/dev/input/event6"
    [ 25.840] (--) Power Button: Found keys
    [ 25.840] (II) Power Button: Configuring as keyboard
    [ 25.840] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input6/event6"
    [ 25.840] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
    [ 25.840] (**) Option "xkb_rules" "evdev"
    [ 25.840] (**) Option "xkb_model" "evdev"
    [ 25.840] (**) Option "xkb_layout" "us"
    [ 25.868] (II) config/udev: Adding input device Video Bus (/dev/input/event12)
    [ 25.868] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
    [ 25.868] (II) Using input driver 'evdev' for 'Video Bus'
    [ 25.868] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.869] (**) Video Bus: always reports core events
    [ 25.869] (**) Video Bus: Device: "/dev/input/event12"
    [ 25.869] (--) Video Bus: Found keys
    [ 25.869] (II) Video Bus: Configuring as keyboard
    [ 25.869] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input12/event12"
    [ 25.869] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
    [ 25.869] (**) Option "xkb_rules" "evdev"
    [ 25.869] (**) Option "xkb_model" "evdev"
    [ 25.869] (**) Option "xkb_layout" "us"
    [ 25.869] (II) config/udev: Adding input device Video Bus (/dev/input/event11)
    [ 25.869] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
    [ 25.869] (II) Using input driver 'evdev' for 'Video Bus'
    [ 25.869] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.869] (**) Video Bus: always reports core events
    [ 25.869] (**) Video Bus: Device: "/dev/input/event11"
    [ 25.869] (--) Video Bus: Found keys
    [ 25.869] (II) Video Bus: Configuring as keyboard
    [ 25.869] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:19/LNXVIDEO:00/input/input11/event11"
    [ 25.869] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)
    [ 25.869] (**) Option "xkb_rules" "evdev"
    [ 25.869] (**) Option "xkb_model" "evdev"
    [ 25.869] (**) Option "xkb_layout" "us"
    [ 25.869] (II) config/udev: Adding input device Power Button (/dev/input/event4)
    [ 25.869] (**) Power Button: Applying InputClass "evdev keyboard catchall"
    [ 25.869] (II) Using input driver 'evdev' for 'Power Button'
    [ 25.869] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.869] (**) Power Button: always reports core events
    [ 25.869] (**) Power Button: Device: "/dev/input/event4"
    [ 25.869] (--) Power Button: Found keys
    [ 25.869] (II) Power Button: Configuring as keyboard
    [ 25.869] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4/event4"
    [ 25.869] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 9)
    [ 25.869] (**) Option "xkb_rules" "evdev"
    [ 25.869] (**) Option "xkb_model" "evdev"
    [ 25.869] (**) Option "xkb_layout" "us"
    [ 25.870] (II) config/udev: Adding input device Lid Switch (/dev/input/event3)
    [ 25.870] (II) No input driver specified, ignoring this device.
    [ 25.870] (II) This device may have been added with another device file.
    [ 25.870] (II) config/udev: Adding input device Sleep Button (/dev/input/event5)
    [ 25.870] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
    [ 25.870] (II) Using input driver 'evdev' for 'Sleep Button'
    [ 25.870] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.870] (**) Sleep Button: always reports core events
    [ 25.870] (**) Sleep Button: Device: "/dev/input/event5"
    [ 25.870] (--) Sleep Button: Found keys
    [ 25.870] (II) Sleep Button: Configuring as keyboard
    [ 25.870] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5/event5"
    [ 25.870] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 10)
    [ 25.870] (**) Option "xkb_rules" "evdev"
    [ 25.870] (**) Option "xkb_model" "evdev"
    [ 25.870] (**) Option "xkb_layout" "us"
    [ 25.870] (II) config/udev: Adding input device Laptop_Integrated_Webcam_FHD (/dev/input/event8)
    [ 25.870] (**) Laptop_Integrated_Webcam_FHD: Applying InputClass "evdev keyboard catchall"
    [ 25.870] (II) Using input driver 'evdev' for 'Laptop_Integrated_Webcam_FHD'
    [ 25.870] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.870] (**) Laptop_Integrated_Webcam_FHD: always reports core events
    [ 25.870] (**) Laptop_Integrated_Webcam_FHD: Device: "/dev/input/event8"
    [ 25.870] (--) Laptop_Integrated_Webcam_FHD: Found keys
    [ 25.870] (II) Laptop_Integrated_Webcam_FHD: Configuring as keyboard
    [ 25.870] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.0/input/input8/event8"
    [ 25.870] (II) XINPUT: Adding extended input device "Laptop_Integrated_Webcam_FHD" (type: KEYBOARD, id 11)
    [ 25.870] (**) Option "xkb_rules" "evdev"
    [ 25.870] (**) Option "xkb_model" "evdev"
    [ 25.870] (**) Option "xkb_layout" "us"
    [ 25.871] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event13)
    [ 25.871] (II) No input driver specified, ignoring this device.
    [ 25.871] (II) This device may have been added with another device file.
    [ 25.871] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event14)
    [ 25.871] (II) No input driver specified, ignoring this device.
    [ 25.871] (II) This device may have been added with another device file.
    [ 25.871] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event15)
    [ 25.871] (II) No input driver specified, ignoring this device.
    [ 25.871] (II) This device may have been added with another device file.
    [ 25.871] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event16)
    [ 25.871] (II) No input driver specified, ignoring this device.
    [ 25.871] (II) This device may have been added with another device file.
    [ 25.871] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event1)
    [ 25.871] (**) Logitech USB Receiver: Applying InputClass "evdev pointer catchall"
    [ 25.871] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
    [ 25.871] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.871] (**) Logitech USB Receiver: always reports core events
    [ 25.871] (**) Logitech USB Receiver: Device: "/dev/input/event1"
    [ 25.871] (--) Logitech USB Receiver: Found 20 mouse buttons
    [ 25.871] (--) Logitech USB Receiver: Found scroll wheel(s)
    [ 25.871] (--) Logitech USB Receiver: Found relative axes
    [ 25.871] (--) Logitech USB Receiver: Found x and y relative axes
    [ 25.871] (II) Logitech USB Receiver: Configuring as mouse
    [ 25.871] (II) Logitech USB Receiver: Adding scrollwheel support
    [ 25.871] (**) Logitech USB Receiver: YAxisMapping: buttons 4 and 5
    [ 25.871] (**) Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    [ 25.871] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1c.4/0000:0b:00.0/usb2/2-1/2-1:1.0/input/input1/event1"
    [ 25.871] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: MOUSE, id 12)
    [ 25.871] (II) Logitech USB Receiver: initialized for relative axes.
    [ 25.871] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
    [ 25.871] (**) Logitech USB Receiver: (accel) acceleration profile 0
    [ 25.871] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
    [ 25.871] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
    [ 25.872] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/mouse0)
    [ 25.872] (II) No input driver specified, ignoring this device.
    [ 25.872] (II) This device may have been added with another device file.
    [ 25.872] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event2)
    [ 25.872] (**) Logitech USB Receiver: Applying InputClass "evdev keyboard catchall"
    [ 25.872] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
    [ 25.872] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.872] (**) Logitech USB Receiver: always reports core events
    [ 25.872] (**) Logitech USB Receiver: Device: "/dev/input/event2"
    [ 25.872] (--) Logitech USB Receiver: Found 1 mouse buttons
    [ 25.872] (--) Logitech USB Receiver: Found scroll wheel(s)
    [ 25.872] (--) Logitech USB Receiver: Found relative axes
    [ 25.872] (--) Logitech USB Receiver: Found absolute axes
    [ 25.872] (--) Logitech USB Receiver: Found keys
    [ 25.872] (II) Logitech USB Receiver: Configuring as mouse
    [ 25.872] (II) Logitech USB Receiver: Configuring as keyboard
    [ 25.872] (II) Logitech USB Receiver: Adding scrollwheel support
    [ 25.872] (**) Logitech USB Receiver: YAxisMapping: buttons 4 and 5
    [ 25.872] (**) Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    [ 25.872] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1c.4/0000:0b:00.0/usb2/2-1/2-1:1.1/input/input2/event2"
    [ 25.872] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD, id 13)
    [ 25.872] (**) Option "xkb_rules" "evdev"
    [ 25.872] (**) Option "xkb_model" "evdev"
    [ 25.872] (**) Option "xkb_layout" "us"
    [ 25.872] (EE) Logitech USB Receiver: failed to initialize for relative axes.
    [ 25.872] (II) Logitech USB Receiver: initialized for absolute axes.
    [ 25.872] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
    [ 25.872] (**) Logitech USB Receiver: (accel) acceleration profile 0
    [ 25.872] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
    [ 25.872] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
    [ 25.872] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
    [ 25.872] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
    [ 25.872] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
    [ 25.872] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.872] (**) AT Translated Set 2 keyboard: always reports core events
    [ 25.872] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event0"
    [ 25.872] (--) AT Translated Set 2 keyboard: Found keys
    [ 25.872] (II) AT Translated Set 2 keyboard: Configuring as keyboard
    [ 25.872] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
    [ 25.872] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 14)
    [ 25.873] (**) Option "xkb_rules" "evdev"
    [ 25.873] (**) Option "xkb_model" "evdev"
    [ 25.873] (**) Option "xkb_layout" "us"
    [ 25.873] (II) config/udev: Adding input device AlpsPS/2 ALPS DualPoint TouchPad (/dev/input/event10)
    [ 25.873] (**) AlpsPS/2 ALPS DualPoint TouchPad: Applying InputClass "evdev touchpad catchall"
    [ 25.873] (**) AlpsPS/2 ALPS DualPoint TouchPad: Applying InputClass "touchpad catchall"
    [ 25.873] (II) LoadModule: "synaptics"
    [ 25.873] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
    [ 25.883] (II) Module synaptics: vendor="X.Org Foundation"
    [ 25.884] compiled for 1.11.0, module version = 1.5.0
    [ 25.884] Module class: X.Org XInput Driver
    [ 25.884] ABI class: X.Org XInput driver, version 13.0
    [ 25.884] (II) Using input driver 'synaptics' for 'AlpsPS/2 ALPS DualPoint TouchPad'
    [ 25.884] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
    [ 25.884] (**) AlpsPS/2 ALPS DualPoint TouchPad: always reports core events
    [ 25.884] (**) Option "Device" "/dev/input/event10"
    [ 25.884] (--) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: x-axis range 0 - 2000
    [ 25.884] (--) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: y-axis range 0 - 1400
    [ 25.884] (--) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: pressure range 0 - 127
    [ 25.884] (II) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: device does not report finger width.
    [ 25.884] (--) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: buttons: left right middle double triple
    [ 25.884] (--) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: Vendor 0x2 Product 0x8
    [ 25.884] (--) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: invalid finger width range. defaulting to 0 - 15
    [ 25.884] (**) Option "TapButton1" "1"
    [ 25.884] (**) Option "TapButton2" "2"
    [ 25.884] (**) Option "TapButton3" "3"
    [ 25.884] (--) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: touchpad found
    [ 25.884] (**) AlpsPS/2 ALPS DualPoint TouchPad: always reports core events
    [ 25.884] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input10/event10"
    [ 25.884] (II) XINPUT: Adding extended input device "AlpsPS/2 ALPS DualPoint TouchPad" (type: TOUCHPAD, id 15)
    [ 25.884] (**) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: (accel) MinSpeed is now constant deceleration 2.5
    [ 25.884] (**) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: MaxSpeed is now 1.75
    [ 25.884] (**) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: AccelFactor is now 0.082
    [ 25.884] (**) AlpsPS/2 ALPS DualPoint TouchPad: (accel) keeping acceleration scheme 1
    [ 25.884] (**) AlpsPS/2 ALPS DualPoint TouchPad: (accel) acceleration profile 1
    [ 25.884] (**) AlpsPS/2 ALPS DualPoint TouchPad: (accel) acceleration factor: 2.000
    [ 25.884] (**) AlpsPS/2 ALPS DualPoint TouchPad: (accel) acceleration threshold: 4
    [ 25.884] (--) synaptics: AlpsPS/2 ALPS DualPoint TouchPad: touchpad found
    [ 25.885] (II) config/udev: Adding input device AlpsPS/2 ALPS DualPoint TouchPad (/dev/input/mouse2)
    [ 25.885] (II) No input driver specified, ignoring this device.
    [ 25.885] (II) This device may have been added with another device file.
    [ 25.885] (II) config/udev: Adding input device DualPoint Stick (/dev/input/event9)
    [ 25.885] (**) DualPoint Stick: Applying InputClass "evdev pointer catchall"
    [ 25.885] (II) Using input driver 'evdev' for 'DualPoint Stick'
    [ 25.885] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.885] (**) DualPoint Stick: always reports core events
    [ 25.885] (**) DualPoint Stick: Device: "/dev/input/event9"
    [ 25.885] (--) DualPoint Stick: Found 3 mouse buttons
    [ 25.885] (--) DualPoint Stick: Found relative axes
    [ 25.885] (--) DualPoint Stick: Found x and y relative axes
    [ 25.885] (II) DualPoint Stick: Configuring as mouse
    [ 25.885] (**) DualPoint Stick: YAxisMapping: buttons 4 and 5
    [ 25.885] (**) DualPoint Stick: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    [ 25.885] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input9/event9"
    [ 25.885] (II) XINPUT: Adding extended input device "DualPoint Stick" (type: MOUSE, id 16)
    [ 25.885] (II) DualPoint Stick: initialized for relative axes.
    [ 25.885] (**) DualPoint Stick: (accel) keeping acceleration scheme 1
    [ 25.885] (**) DualPoint Stick: (accel) acceleration profile 0
    [ 25.885] (**) DualPoint Stick: (accel) acceleration factor: 2.000
    [ 25.885] (**) DualPoint Stick: (accel) acceleration threshold: 4
    [ 25.885] (II) config/udev: Adding input device DualPoint Stick (/dev/input/mouse1)
    [ 25.885] (II) No input driver specified, ignoring this device.
    [ 25.885] (II) This device may have been added with another device file.
    [ 25.885] (II) config/udev: Adding input device Dell WMI hotkeys (/dev/input/event7)
    [ 25.885] (**) Dell WMI hotkeys: Applying InputClass "evdev keyboard catchall"
    [ 25.885] (II) Using input driver 'evdev' for 'Dell WMI hotkeys'
    [ 25.885] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 25.885] (**) Dell WMI hotkeys: always reports core events
    [ 25.885] (**) Dell WMI hotkeys: Device: "/dev/input/event7"
    [ 25.885] (--) Dell WMI hotkeys: Found keys
    [ 25.885] (II) Dell WMI hotkeys: Configuring as keyboard
    [ 25.885] (**) Option "config_info" "udev:/sys/devices/virtual/input/input7/event7"
    [ 25.885] (II) XINPUT: Adding extended input device "Dell WMI hotkeys" (type: KEYBOARD, id 17)
    [ 25.885] (**) Option "xkb_rules" "evdev"
    [ 25.886] (**) Option "xkb_model" "evdev"
    [ 25.886] (**) Option "xkb_layout" "us"
    [ 25.896] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments
    [ 39.128] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 39.128] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 39.128] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 39.128] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 52.382] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 52.382] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 52.382] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 52.382] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 53.649] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 53.649] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 53.649] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 53.649] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 54.483] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 54.483] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 54.483] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 54.483] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 54.551] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 54.551] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 54.551] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 54.551] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 54.619] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 54.619] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 54.619] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 54.619] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 54.686] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 54.686] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 54.686] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 54.686] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 54.751] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 54.751] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 54.751] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 54.751] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 54.816] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 54.816] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 54.816] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 54.816] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 54.900] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 54.900] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 54.900] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 54.900] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 55.376] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 55.377] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 55.377] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 55.377] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 55.459] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 55.459] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 55.459] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 55.460] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 55.547] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 55.547] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 55.547] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 55.547] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 55.625] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 55.625] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 55.625] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 55.625] (II) fglrx(0): Modeline "1366x768"x0.0 51.00 1366 1402 1450 1564 768 771 776 814 -hsync -vsync (32.6 kHz)
    [ 55.697] (II) fglrx(0): EDID vendor "LGD", prod id 739
    [ 55.697] (II) fglrx(0): Printing DDC gathered Modelines:
    [ 55.697] (II) fglrx(0): Modeline "1366x768"x0.0 76.00 1366 1402 1450 1564 768 771 776 810 -hsync -vsync (48.6 kHz)
    [ 55.697] (II) fglrx(0): Modeline "1366x768"x0.0

    Hello,
    i get the same messages without any problems for my intel card.
    You can read more about it in this thread:
    http://forums.gentoo.org/viewtopic-t-85 … ec66f93bf2
    There are a fair amount of people who have posted their /proc/mtrr there, you can compare yours to them.
    In the end they come to the conclusion, that uncachable entries are not a problem, for the most systems.
    However uncachable regions of 1024MB seem to be too large.
    On my mtrr the biggest uncachable entry is 64MB.
    So you might get improvement from solving this.

  • My Dell Vostro (running XP SP3) neither recognizes my iPad 2 nor my iPhone 4 correctly! I followed the troubleshooting guides and installed the latest iTunes. Both devices are recognised by my desktop PC running Vista using the exact same cable etc.

    Hello all,
    my Laptop (Dell Vostro - running XP SP3) neither recognizes my iPad 2 nor my iPhone 4! 
    Both devices are working correctly with my desktop PC running Vista with the same USB cable!  
    I followed trouble shooting guides, checked that the drivers are present, installed, removed and reinstalled the latest iTunes (in the correct order together with the other Apple software components) etc. but nothing works! The interesting thing is that when I plug the iPad or the iPhone in the laptop's usb-port for a second Windows correctly shows the devices either as iPad or iPhone in the "Device Manager" with an exclamation point !!!    But then after a split second Windows allways switches the devices to Digital Camera and the correct iPad or iPhone disappears !!!     =>    That is why I guess that this is a driver problem!
    Does anybody have any idea what else I can try?
    Is there a manual way to install the drivers for the iPad 2 or iPhone 4?
    Many thanks for your ideas and suggestions
    Edgar

    Yes I know that (I always google first and ask later ). Too bad I find this out when it was too late. I was already on 4.3.

  • Elantech Touchpad Detected As PS/2 Elantech Mouse (Dell Vostro 3560)

    Dear community,
    I am facing troubles with my Dell Vostro 3560's Elantech Touchpad. It gets detected as PS/2 Elantech mouse.
    [acs@einherij ~]$ xinput list
    ⎡ Virtual core pointer id=2 [master pointer (3)]
    ⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer (2)]
    ⎜ ↳ PS/2 Elantech Mouse id=12 [slave pointer (2)]
    ⎣ Virtual core keyboard id=3 [master keyboard (2)]
    ↳ Virtual core XTEST keyboard id=5 [slave keyboard (3)]
    ↳ Power Button id=6 [slave keyboard (3)]
    ↳ Video Bus id=7 [slave keyboard (3)]
    ↳ Power Button id=8 [slave keyboard (3)]
    ↳ Sleep Button id=9 [slave keyboard (3)]
    ↳ Laptop_Integrated_Webcam_E4HD id=10 [slave keyboard (3)]
    ↳ AT Translated Set 2 keyboard id=11 [slave keyboard (3)]
    ↳ Dell WMI hotkeys id=13 [slave keyboard (3)]
    Testwise. I installed from AUR the "psmouse-elantech" package (as mentioned in the Touchpad Synaptics article). After reboot, no effect at all, xinput gives the same output.
    Can somebody point me in the correct direction please?
    --- snip /var/log/Xorg.0.log ---
    [ 11.978] (II) config/udev: Adding input device PS/2 Elantech Mouse (/dev/input/event11)
    [ 11.978] (**) PS/2 Elantech Mouse: Applying InputClass "evdev pointer catchall"
    [ 11.978] (II) Using input driver 'evdev' for 'PS/2 Elantech Mouse'
    [ 11.978] (**) PS/2 Elantech Mouse: always reports core events
    [ 11.978] (**) evdev: PS/2 Elantech Mouse: Device: "/dev/input/event11"
    [ 11.978] (--) evdev: PS/2 Elantech Mouse: Vendor 0x2 Product 0x1
    [ 11.978] (--) evdev: PS/2 Elantech Mouse: Found 3 mouse buttons
    [ 11.978] (--) evdev: PS/2 Elantech Mouse: Found relative axes
    [ 11.978] (--) evdev: PS/2 Elantech Mouse: Found x and y relative axes
    [ 11.978] (II) evdev: PS/2 Elantech Mouse: Configuring as mouse
    [ 11.978] (**) evdev: PS/2 Elantech Mouse: YAxisMapping: buttons 4 and 5
    [ 11.978] (**) evdev: PS/2 Elantech Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    [ 11.978] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input11/event11"
    [ 11.978] (II) XINPUT: Adding extended input device "PS/2 Elantech Mouse" (type: MOUSE, id 12)
    [ 11.978] (II) evdev: PS/2 Elantech Mouse: initialized for relative axes.
    --- snap ---
    Last edited by sonnyka (2012-08-07 16:58:44)

    also see: https://bbs.archlinux.org/viewtopic.php?id=117109

Maybe you are looking for