Troubles with kernel_task

Hello ,
I was running Mountain Lion , some days ago , and i got THE problem , kernel_task eats 300% of CPU and the system it too slow !
After reading all what i found on internet and tested all the tricks without result , i upgraded to Maverick , same problem ... so i done a clean install of maverick today , same problem ! i done a complete Hardware test using AHT , nothing wrong !
What can be the problem ?!!
Thank you for helping.

The kernel is using excessive processor cycles. Below are some possible causes for the condition.
Throttling
When it gets high temperature readings from the hardware, or a low-voltage reading from the battery, the kernel may try to compensate by interrupting the processor(s) to slow them down and reduce power consumption. This condition can be due to
a buildup of dust on the logic board
high ambient temperature
a worn-out or faulty battery in a portable
the malfunction of a cooling fan or sensor
Note that if the problem is caused by a sensor, there may be no actual overheating or undervoltage.
If the computer is portable, test with and without the AC adapter connected. If kernel_task hogs the processor only on battery power, the fault is in the battery or the logic board. If it happens only on AC power, charging is causing the machine to heat up. That may be normal on some models. CPU usage should drop when charging is complete.
Apple Diagnostics or the Apple Hardware Test, though not very reliable, is sometimes able to detect a bad fan or sensor.
If nothing is wrong with the hardware, then whatever you can do to improve cooling may help.
Installed software
User-installed software that includes a device driver or other kernel code may thrash the kernel. That category includes virtualization software, such as Parallels and VMware, as well as most commercial "anti-virus" products. Some system-monitoring applications, such as "iStat," can also contribute to the problem. You can test for this possibility by completely disabling or removing the software according to the developer's instructions, or booting in safe mode. Note, however, that disabling a system modification without removing it or booting in safe mode may not be as easy as you think it is.
Corrupt NVRAM or SMC data
Sometimes the problem is cleared up by resetting the NVRAM or the SMC.
External display
Connecting an external LCD display to some MacBook Pro models may cause this issue. If applicable, test by disconnecting the display. You might get better results with a newer LED display.

Similar Messages

I have been having a lot of trouble with the latest itunes update and my ipod classic 80Gb i.e. being unable to sync songs, but now i have no files at all on my ipod, it is completely blank when i view it from my computer. I need help, please, anybody.

As it says above, i have been having a lot f trouble with my ipod classic and the latest itunes update, i was unable to sync songs or anything to it and have tried every conceivable 'fix' i could find. i have run an itunes diagnostic and the results are posted below. a major problem is that when i try and view my ipod through my computer it displays nothing at all on the ipod, no files or anything, this may be the problem but i have no idea how it has happened or how i could resolve it.
This ipod holds huge sentimental value and i am loathe to buy a new one! If anybody can help it is greatly appreciated, than kyou in advanced.
Microsoft Windows 7 x64 Home Premium Edition Service Pack 1 (Build 7601)
ASUSTeK Computer Inc. K50IJ
iTunes 11.1.5.5
QuickTime not available
FairPlay 2.5.16
Apple Application Support 3.0.1
iPod Updater Library 11.1f5
CD Driver 2.2.3.0
CD Driver DLL 2.1.3.1
Apple Mobile Device 7.1.1.3
Apple Mobile Device Driver 1.64.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 0038B8600B98D1E0
Current user is not an administrator.
The current local date and time is 2014-03-21 16:52:39.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is supported.
Video Display Information
Intel Corporation, Mobile Intel(R) 4 Series Express Chipset Family
Intel Corporation, Mobile Intel(R) 4 Series Express Chipset Family
**** External Plug-ins Information ****
No external plug-ins installed.
Genius ID: 2fd81a1f13cf3ff25a8b4f0e8e725116
**** Device Connectivity Tests ****
iPodService 11.1.5.5 (x64) is currently running.
iTunesHelper 11.1.5.5 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Intel(R) ICH9 Family USB Universal Host Controller - 2934. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2935. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2936. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2937. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2938. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2939. Device is working properly.
Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293A. Device is working properly.
Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293C. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.

Here is what worked for me:
My usb hub, being usb2, was too fast. I moved the wire to a usb port directory on my pc. That is a usb1 port which is slow enough to run your snyc.

Trouble with Toshiba built-in webcam: "unable to enumerate USB device"

I am running archlinux on a Toshiba Satellite L70-B-12H laptop, and having troubles with the Webcam. *Once in a while*, everything goes well and I get
# lsusb
Bus 004 Device 002: ID 8087:8000 Intel Corp.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 004: ID 04f2:b448 Chicony Electronics Co., Ltd
Bus 003 Device 003: ID 8087:07dc Intel Corp.
Bus 003 Device 002: ID 8087:8008 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
# dmesg
[ 3433.456115] usb 3-1.3: new high-speed USB device number 4 using ehci-pci
[ 3433.781119] media: Linux media interface: v0.10
[ 3433.809842] Linux video capture interface: v2.00
[ 3433.826889] uvcvideo: Found UVC 1.00 device TOSHIBA Web Camera - HD (04f2:b448)
[ 3433.835893] input: TOSHIBA Web Camera - HD as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.3/3-1.3:1.0/input/input15
[ 3433.835976] usbcore: registered new interface driver uvcvideo
[ 3433.835977] USB Video Class driver (1.1.1)
Unfortunately, *most of the time* the camera seems invisible to my system, and I get
# lsusb
Bus 004 Device 002: ID 8087:8000 Intel Corp.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 8087:07dc Intel Corp.
Bus 003 Device 002: ID 8087:8008 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
(note the missing "04f2:b448 Chicony Electronics Co., Ltd" device), and
# dmesg
[ 480.104252] usb 3-1.3: new full-speed USB device number 4 using ehci-pci
[ 480.171097] usb 3-1.3: device descriptor read/64, error -32
[ 480.341235] usb 3-1.3: device descriptor read/64, error -32
[ 480.511375] usb 3-1.3: new full-speed USB device number 5 using ehci-pci
[ 480.578007] usb 3-1.3: device descriptor read/64, error -32
[ 480.748151] usb 3-1.3: device descriptor read/64, error -32
[ 480.918282] usb 3-1.3: new full-speed USB device number 6 using ehci-pci
[ 481.325196] usb 3-1.3: device not accepting address 6, error -32
[ 481.392091] usb 3-1.3: new full-speed USB device number 7 using ehci-pci
[ 481.798926] usb 3-1.3: device not accepting address 7, error -32
[ 481.799166] hub 3-1:1.0: unable to enumerate USB device on port 3
Searching on the web, most results I found lead to this page, where it is said that the problem is due to badly tuned overcurrent protection, and advocated that unplugging and switching off the computer for a little while gets things back into normal. This does not really work for me; the problem seems to occur more randomly, unfortunately with high probability (my camera is available after less than one boot out of ten).
I tried to ensure that the ehci-hcd module is loaded at boot with the ignore-oc option (with a file in /etc/module-load.d/), to no avail.
I also wrote a script which alternatively removes and reloads the ehci-pci driver until my device is found in lsusb. It is sometimes helpful, but usually not. And even when my device is found that way, it can only be used for a while before disappearing again.
Anyway, such a hack is unacceptable... So, my questions are:
is it indeed related to overcurrent protection ?
is there anything else I can try ?
should I file somewhere an other of the numerous bug reports about "unable to enumerate USB device" already existing ?
If of any importance, I am running linux 3.15.7, because at the time I installed my system, I couldn't get the hybrid graphic card Intel/AMD working under 3.16.
Last edited by $nake (2014-10-18 16:29:06)

uname -a
Linux libra 3.9.4-1-ARCH #1 SMP PREEMPT Sat May 25 16:14:55 CEST 2013 x86_64 GNU/Linux
pacman -Qi linux
Name : linux
Version : 3.9.4-1
Description : The linux kernel and modules
Architecture : x86_64
URL : http://www.kernel.org/
Licences : GPL2
Groups : base
Provides : kernel26=3.9.4
Depends On : coreutils linux-firmware kmod mkinitcpio>=0.7
Optional Deps : crda: to set the correct wireless channels of your country
Required By : nvidia
Optional For : None
Conflicts With : kernel26
Replaces : kernel26
Installed Size : 65562.00 KiB
Packager : Tobias Powalowski <[email protected]>
Build Date : Sat 25 May 2013 16:28:17 CEST
Install Date : Sun 02 Jun 2013 15:30:35 CEST
Install Reason : Explicitly installed
Install Script : Yes
Validated By : Signature

Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

Hello Sue,
I have an iPad 3, iPad Mini and iPhone 5S and they are all sluggish on capitalisation using shift keys. I hope that Apple will solve the problem because it is driving me crazy.
I find using a Microsoft Surface and Windows 8 phone, which I also have, work as well as all the ios devices before the ios 7 upgrade.
It has something to do with the length of time that you need to hold the shift key down. The shift key needs to be held longer than the letter key for the capitalisation to work. For some reason, this is a major change in the way we have learnt to touch type on computers. I am having to relearn how to type!
Michael

Trouble with OR in where clause

Hello,
I'm having trouble with execution speed. The problem seems to be with using OR in my where clause.
Here's the meat of the function where i_pledge_number is an input parm:
BEGIN
SELECT /*+ INDEX (pp) */ SUM(pp.prim_pledge_amount)
INTO return_amount
FROM
primary_pledge pp
WHERE
-- Get total if multiple allocations
pp.prim_pledge_number IN
(SELECT pc.pledge_number
FROM pledge_codes pc
WHERE pc.pledge_code_type = 'M'
AND pc.pledge_code = 'AC'
AND lpad(pc.pledge_comment,10,'0') = i_pledge_number)
-- Get total if single allocation
OR pp.prim_pledge_number = i_pledge_number;
RETURN return_amount;
END;
If I comment out either half of the OR statement (either the subquery or the pp.prim_pledge_number = i_pledge_number half) the function returns a value in .02 seconds. If I leave the OR in, it takes 2.764 seconds to execute?? Can someone please show me a better way (faster) to do this? I tried using nvl() around the subquery but couldn't get it to compile.
Thanks

These things are difficult to diagnose remotely, but here is something you can try....
SELECT */ SUM(pp.prim_pledge_amount)
INTO return_amount
FROM   primary_pledge pp
WHERE pp.prim_pledge_number IN (SELECT pc.pledge_number
                                 FROM pledge_codes pc
                                 WHERE pc.pledge_code_type = 'M'
                                 AND pc.pledge_code = 'AC'
                                 AND lpad(pc.pledge_comment,10,'0') = i_pledge_number
UNION ALL
SELECT i_pledge_number FROM dual)
   RETURN return_amount;
END;If that doesn't do anything (and it might well not) there are a large number of different ways we can recast this query. To save us further guessing please give us more details: execution plans, database version number, volumetrics.
Cheers, APC

A trouble with "LIKE" in a select statement

Hi!
I'm having trouble with "LIKE" in a select statement...
With Access I can make the following and everything works well:
SELECT name, birthday
FROM client
WHERE birthday LIKE '*/02/*';
but if try to do it in my application (it uses Access), it doesn't work - I just can't understand that!!!
In my application the "month" is always the currently month taken from the "System". Look what I'm doing...
String query1 = "SELECT name, birthday " +
          "FROM client " +
          "WHERE birthday " +
          "LIKE '*/" +
          pMonth +
          "/*' " +
          "ORDER BY birthday ASC ";
ResultSet rs = statement1.executeQuery(consulta1);
boolean moreRecords = rs.next();
The variable "moreRecords" is always "false", the query returns nothing although the table "client" has records that attend the query.
Please, anyone can help me?! It's a little bit urgent.
Thanks,
Katia.

Hi Katia,
I'll bet the problem lies with the characters you're using to escape the LIKE clause. You're using the ones that Access likes to see, but that's not necessarily what's built into the JDBC-ODBC driver class.
You can find out what the correct escape wildcard characters are from the java.sql.DatabaseMetaData.getSearchStringEscape() method. It'll tell you what to use in the LIKE clause.
I'm not 100% sure about your code. It doesn't use query1 anywhere. I'd do this:
String query = "SELECT name, birthday FROM client WHERE birthday LIKE ? ORDER BY birthday ASC";
PreparedStatement statement = connection.createStatement(query);
String escape = connection.getMetaData().getSearchStringEscape();
String test = escape + '/' + pMonth + '/' + escape;
statement.setString(1, test);
ResultSet rs = statement.executeQuery();
while (rs.hasNext())
// load your data into a data structure to pass back.
rs.close();
statement.close();Let me know if that works. - MOD

(Trouble printing) Trouble with connection between Macbook Pro and Hp Deskjet 1510.

Trouble with connection between Macbook Pro and Hp Deskjet 1510. (Nothing Prints).
I have a Macbook Pro and am having difficulty printing documents from ‘Pages' from my Hp Deskjet 1510. I have installed the necessary software for the printer and it is connected via USB. Every time I try to print the printer icon comes up as it should, 'printing' and then 'job completed' and then the icon disappears. (Nothing is printed.) I thought it might be something to do with Pages compatibility with the printer but exporting the document to Word or making it a PDF doesn’t change anything. I don’t have Microsoft Word on my computer. The scanner does work and when I printed a ‘Test Page’ that worked too.
Let me know if you know why this is happening.

With these settings the network now works flawlessly, however, when i have my ethernet cable plugged in, my internet access via my airport card(on the macbook pro) is no longer available. Hoping you can tell me why this would be with this info i've provided.
Educated guess. The networking devices have priorities as to which are used. The standard order is that Ethernet has a higher priority than Airport.
While your Ethernet is unplugged it is inactive and the Mac ignores it. Once you plug it in, the Mac sees that it is active and switches traffic to that interface.
I actually take advantage of this feature at home, but configuring my Airport and Ethernet with identical fixed IP addresses. Normally I'll use Airport, but if I'm copying a huge file and I want faster performance, I'll just walk my MacBook (previously iBook, previously Powerbook) over to my Ethernet switch and plug in my MacBook. Magically, the Mac detects that the Ethernet is active and continues the file transfer uninterrupted over the faster 100baseT Ethernet connection. When the transfer is finished, or if I really need to move back to the Comfy Chair, I unplug the Ethernet cable, and all activity reverts back to the Airport, all without disrupting any existing networking connections.
You on the other hand have totally different settings for your Ethernet and your Airport, so when you switch to Ethernet, you basically loose your Airport connections.
Something you can try:
System Preferences -> Network
Gear icon on the bottom left, next to the [+] [-] icons.
Select *Set Service Order...*
Now Drag the network interfaces into the perfer priority order you want. In this case put Airport above Ethernet.
NOTE: You may want to create a new Network Location for this, instead of messing with your normal home Location (which is most likely the default Automatic. That way you have your original you can always fall back to.

Edge Animation having troubles with iOS devices within Muse Site

Hi All! I've been creating a mobile version of my website www.rinkdesigns.com and have it all complete. I created an animation/navigation bar within Adobe Edge Animate and imported it into Muse. It functions AMAZINGLY on my Nexus 4 (Android) in Chrome but on a buddies iPhone 5 Chrome only loads about 3/4 of the animation/nav bar, in Safari the animation does not load at all and half of the page background does not load either. Please check out the preview site here http://rinkdesignsmobile.businesscatalyst.com/phone
Has anyone else been having animation/mobile troubles with iOS devices? Any hints as to how you fixed your errors would be extremely helpful! I also posted this question in the Muse forum and haven't gotten a response...
Thanks,
John

Or, how about this:
Does anyone know how to have Edge Animate objects that utilize "_top" in an open url trigger make the Muse site that they are a part of open a new window/tab with that action (as opposed to having it open the url in the current page, or using "_blank" in the trigger)?

Trouble with 3rd party VST installs for Garageband, can't find instruments

Hi,
I am having trouble with Audio Units for Garageband when installing 3rd party software, VSTs, loops, instruments. I have more issues with Logic Pro. I am hoping that it is the same underlying issue and that I am just missing something. I have the manuals (not great for troubleshooting). I am confused with some installs use User Library and others use the Computer Library. I do go to the mfgs sites for updates. The installs sometimes work as standalones but I don't see ALL of the components of the software in say Garageband or Logic. Mostly, I am missing the "instruments" and "loops" that I want to access within the DAW. Some examples:
• Here is some of the software I am talking about: East West sample libraries (Play and Native Instruments); Vienna Symphonic librarires; Sylenth1 (just last night); Sample Tank 2 and Total Workstation 2 from IK Multimedia and others.
• In GB I see the Audio Units for Vienna, Play, Sylenth, some of the IK Multimedia but NOT any instruments when I go to the "Sound Generator" -- I seem to be missing the instruments and loops. I see less AUs in Logic Pro. Some of these are VST instruments.
• Can I just drag-drop samples to the library folders to fix this?
• The plug-ins do not seem to work (though Sylenth1 worked for a single sound). When there is a standalone app (as in Sample Tank), I finally got the "sounds" to be reinstalled and loaded, those sounds/samples don't show up in any DAW.
• When and if the sounds/loops/samples show up in GB's "Instruments" section will I be able to tell that they belong to that particular software or library?
Thanks in advance.
John

Found the answer myself, it was simple:
• Select the Track
• Show the Instrument (info area)
• Click on Edit
• Click on the "Sound Generator" pop up field.
• At the bottom of the pop-up list, select from the Audio Units that you have installed. This is where you see "Sample Tank 2, Vienna Instruments..."
• NEXT -- IMPORTANT: CLICK ON THE PICTURE next to the Sound Generator pop-up field.The AU unit loads up, the interface pops up, you load up the instruments in this AU Unit. You do NOT see the sounds from the AU unit in the normal Apple instrument list.
This was not intuitive but once you know it, fairly simple.
Still, the devil is in the details -- more questions on the way.

I'm having trouble with something that redirects Google search results when I use Firefox on my PC. It's called the 'going on earth' virus. Do you have a fix that could rectify the vulnerability in your software?

I'm having trouble with a virus or something which affects Google search results when I use Firefox on my PC ...
When I search a topic gives me pages of links as normal, but when I click on a link, the page is hijacked to a site called 'www.goingonearth.com' ...
I've done a separate search and found that other users are affected, but there doesn't seem to be a clear-cut solution ... (Norton, McAfee and Kaspersky don't seem to be able to detect/fix it).
I'd like to continue using the Firefox/Google combination (nb: the hijack virus also affects IE but not Safari) - do you have a patch/fix that could rectify the vulnerability in your software?
thanks

''' "... vulnerability in your software?" ''' 
And it affects IE, too? Ya probably picked up some malware and you blame it on Firefox.
Install, update, and run these programs in this order. They are listed in order of efficacy. '''''(Not all programs detect the same Malware, so you may need to run them all to solve your problem.)''''' These programs are all free for personal use, but some have limited functionality in the "free mode" - but those are features you really don't need to find and remove the problem that you have. 
''Note: If your Malware infection is bad enough and you are mis-directed to URL's other than what is posted, you may have to use a different PC to download these programs and use a USB stick to transfer them to the afflicted PC.''
Malwarebytes' Anti-Malware - [http://www.malwarebytes.org/mbam.php] 
SuperAntispyware - [http://www.superantispyware.com/] 
AdAware - [http://www.lavasoftusa.com/software/adaware/] 
Spybot Search & Destroy - [http://www.safer-networking.org/en/index.html] 
Windows Defender: Home Page - [http://www.microsoft.com/windows/products/winfamily/defender/default.mspx] 
Also, if you have a search engine re-direct problem, see this: 
http://deletemalware.blogspot.com/2010/02/remove-google-redirect-virus.html
If these don't find it or can't clear it, post in one of these forums for specialized malware removal help: 
[http://www.spywarewarrior.com/index.php] 
[http://forum.aumha.org/] 
[http://www.spywareinfoforum.com/] 
[http://bleepingcomputer.com]

TS3274 my ipad is having trouble with my music... i had recently gotten a new one when i signed into my icloud the music that i had on the original one was not there.... some songs were in fact there but not clickable ( it was there only gray)..anyone kno

my ipad is having trouble with my music... i had recently gotten a new one when i signed into my icloud the music that i had on the orignal one was not there.... some songs were in fact there but not clickable ( it was there only gray)... i was looking for help on how to get the music on the ipad

my ipad is having trouble with my music... i had recently gotten a new one when i signed into my icloud the music that i had on the orignal one was not there.... some songs were in fact there but not clickable ( it was there only gray)... i was looking for help on how to get the music on the ipad

I am having trouble with my Mac Mini's ethernet connection. Defining a new network interface shows no ethernet adaptor. Reloading SL from DVD repaired. But SL update lost ethernet again. Will Lion Fix?

I am having trouble with my mac mini ethernet. It had been working for weeks after an update to SL 10.6.8.
Once it went out and i repaired it by defining a new connection from System Preferences ->Network->(left panel service, +).
But yesterday, after a power up. my ethernet was not working again. I tried this old trick to repair it, but the interface choices
listed for '+' a new service did not include Ethernet any more. And the Utilities->System Profiler->Ethernet Cards shows
no ethernet available.
As a last ditch effort i reloaded my original SL from DVD. (I think it was version 10.6.4 but i could be mistaken on the version).
The ethernet worked! But KeyNote wasn't going to work because apparently the version i purchased depends on 10.6.8.
So I upgraded again to SL 10.6.8 (Plus some other updates like AirPort which i don't use).
Now the Ethernet is not working again. I see the same symptoms as before with the Ethernet seeming not installed.
Is this a problem seen by others?
Would going to Lion fix the problem?
Could AirPort actually be the culprit and not SL?
If i stay with my original SL, would i need to repurchase a version of KeyNote for the older version of SL?

Have you reset the SMC?
Shut down the computer.
Unplug the computer's power cord.
Wait fifteen seconds.
Attach the computer's power cord.
Wait five seconds, then press the power button to turn on the computer.
While you're at it, resetting the PRAM won't hurt anything and 'might' help is SMC reset didn't work (PRAM does some port control):
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
Something else you might try .... you don't say how you're updating to 10.6.8, however, if you're using Software Update, you might try downloading the 10.6.8 combo update, which contains all updates to 10.6. Sometimes, Software Update doesn't work quite right, and installing the combo update fixes that. Download the update from Apple's download site at http://support.apple.com/downloads/ , using Disk Utility repair permissions, apply the combo update, then repair permissions again.

I am having trouble with some of my links having images. For example, Foxfire has a picture that looks like a small world. The links in question are blank.

I am having trouble with my links/websites having images attached to them. The place where the image should be is blank. For example, AARP has an A for its image. My storage website has a blank broken box where the image should be. I forgot I had trouble and had to reset Foxfire, this problem occurred after that reset.

cor-el,
Mixed content normally gives the world globe image, unless you are using a theme that uses a broken padlock instead. Maybe the gray triangle means invalid? I came across that in a few themes (what is invalid was not made clear), but those were not using triangle shapes to indicate that.
I came across that mention in one of the pages you posted:
* https://support.mozilla.org/kb/Site+Identity+Button
I cannot attach a screenshot because I have not seen a triangle of any kind in my address bar.

I have an Ipod Touch (4th Gen) and I am having troubles with my downloads from purchasing music from the Ipod. On my downloads icon in the Itunes Store (on Ipod) there is a symbol of how many songs I still have waiting to download, but they wont download.

I have been having troubles with this for months and am extremly tired of not being able to download my songs. I bought these songs off of Itunes as well, so I really hope i can retrieve them. I do not know where to find a personal apple support person yet, does anyone know where to find one on the website?

See these previous discussions:
Waiting applications: Apple Support Communities
Downloading apps stuck on waiting...: Apple Support Communities

I am having trouble with iMessage being activated. It has worked up until yesterday and now won't activate and is saying no address in the send and receive section. My number is there but not ticked. Any suggestions on how to fix this?

I am having trouble with iMessage being activated. It has worked up until yesterday and now won't activate and is saying no address in the send and receive section. My number is there but not ticked. Any suggestions on how to fix this? I have shut down my phone, but still no luck!

iMessage and FaceTime went down yesterday for some people. Mine is still down. My iMessage is saying the same thing about being activated. Sounds like you are still down too. Ignore the status page that says everything is fine - it lies.

Troubles with kernel_task

Similar Messages

Maybe you are looking for