Troubles with WiFi setup
Hi there, I am new in the Arch-world, and I am having some troubles in installing this OS.
I have read every documentation file I found in the web, unfortunately I can't connect the pc to my wifi network.
First, I used LiLi to create a bootable iso on my IoMega HD.
I followed (mainly, but not only because I read other resources on the web) the Wiki wireless setup guide, but with no success.
I have a broadcom wifi card (BCM4313) and according to Ubuntu doc I should not have any troubles.
Using the "wifi-menu" command, I get this error message:
Job for netctl@wlp10s0\x2dTNCAPD1D28F.service failed. See 'systemctl status netctl@wlps0\x2dTNCAPD1D28F.service' and 'journalctl -xn' for details.
Thank you very much!
cris9288 wrote:
if those modules aren't loaded then you can proceed to the next steps. For broadcom-wl to work, the other modules (brcmsmac) have to be removed. If you install broadcom-wl from the aur, it will create a file which automatically blackulists those modules. You then have to make sure you load wl, and it's deps (may be loaded automatically) at boot.
Also, keep in mind that the interface names might be different from the brcmsmac names under the wl module. Always check iwconfig/ip link. The numbers that appear in front of your prompt are the return values from the previous operation, I believe.
what modules do you have loaded right now? You can check with lsmod.
When I write # modprobe wl, I get another error message:
modprobe: FATAL: Module wl not found
Right now I am unable to take a photo, so this is the list of the modules (note that the list fills the display, so probably there are more mods up):
lis3lv02d
mei
ac
input_polldev
battery
processor
evdev
lpc_ich
nfs
lockd
sunrpc
fscache
ext4
crc16
mbcache
jbd2
dm_snapshot
dm_mod
squashfs
loop
nls_cp437
vfat
fat
usb_storage
sr_mod
cdrom
sd_mod
rtsx_pci_sdmmc
mmc_core
ahci
libahci
i915
libata
intel_agp
intel_gtt
crc32c_intel
nouveau
i2c_algo_bit
mxm_wmi
ttm
scsi_mod
drm_kms_helper
ehci_pci
xhci_hcd
rtsx_pci
ehci_hcd
r8169
mii
drm
usbcore
usb_common
i2c_core
wmi
video
button
Similar Messages
-
Having trouble with wifi since upgrading to ios7
Having trouble with wifi since downloading ios7
I have had this problem on my iPad and iPhone 5 since the update in September. I called apple support numerous times, did all the troubleshooting, and went to the apple store and had both devices replaced under warranty. Nothing fixed the problem.
Then as a last ditch effort I called my internet service provider. Turns out that the ios7 doesn't seem to work on a wpa2 network and needs to be changed to a wep network. The tech did this over the phone and now both devices work normally connecting to my wifi! I am still nervous I'm going to run into more issues but so far so good. -
Trouble with wifi after IOS 6 upgrade
I have an iPhone 4 and successfully installed iOS 6 today. I am having trouble getting on my home wifi. When asked to join my network, I click on it and type in my password. Shortly after typing in my correct password an apple.com login page loads from the bottom of the iPhone but says "hmm, the page you're looking for cant be found". The only option I have is to push cancel and then it ends my wifi connection with my own home network. Help please.
burhansheikh replied to Trouble with wifi after IOS 6 upgrade
"guys i have 100% solution copy Wi-FI address from about(general)(setting) & paste to Client ID in your network (Wi-FI) (setting)"
in Using iPhone • 8 replies
1 -
Dear All
Anybody a idea how to solve the following problem. Since upgrade to IOS 6 having problems with WIFI tried everything reset network settings changed the Itunes password, then all of a suden this Saturday WIFI was on line again, I thought yes all problems solved.
Wish it was, Sunday morning no more WIFI, now if I go to settings I am not even aible to turn WIFI on, it seems the screen is blocked and I am not able to switch from OFF to ON.
I already tried to a resset to factory settings via Itunes no luck.
Did anybody have this problem already or anybody any idea to solve this problem?
Kind Regards
JurgenWas the "full" restore a restoe to factory defaults/new iPod?
Try powering off and then back on your router
Reset network settings: Settings>General>Reset>Reset Network Settings
iOS: Troubleshooting Wi-Fi networks and connections -
Downloaded new OS and having trouble with wifi, bluetooth Facebook and Skype performance
Dowloaded 10.2.1.537
When I first loaded this it had a lot of trouble finding my Wifi again and would disengage. Problem went away after a few hours but it recurred this am. Also affected Facebook.
Skype is loading more slowly and jumps to a black screen for 10-20 seconds. Then it will load and function but only for a few seconds to a minute and then shuts off completely.
Launching Skype also resultd in my bluetooth headset being disengaged sometimes.
Reinstalled Skype to see if that fixed anything.
Tried turning off bluetooth to see if that fixed the skype problem - nope still disengaged.
Cycled my router and cable and still no fix...
Running Z30
Would love to get a fix on this.Hello,
Given all of your issues, I'd guess that something did not go well with the update, and a clean reload would be in order. You accomplish that either through the LINK software or by obtaining an AutoLoader.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
i have a mac osx that i have for 4~5 years
so the wifi i was able to connect everytime suddenly had an exclamtion mark on it so i clicked on it and a system app popped up with an option wheither my wifi is D something or P something (i forgot the names im so sorry) and i clicked the D selection ( because it said if my wifi needs an username and a password you have to choose the D selection and if my wifi doesnt need a username or a password you choose the P selection) i typed in my wifi name and the wifi password then clicked continue, my wifi completely doesnt work anymore.
the wifi was connected to all the devices at home but for my laptop it says that the airport cannot be connected.
Please help. what happened? what should i do??Sorry I am a bit lost..
So apparently i made a new service on my wifi and my wifi connected!
If you setup a new wireless name on the Airport Extreme or airport express. Please tell us explicitly what wireless router you have.. is this what you setup the new service on?? And if your wifi on the laptop then connected then everything is fine.
But the thing is my AirPort service (the one i have connected ever since i got the laptop) is still not connected.
You just said you setup a new service and it worked.. why didn't you reset your airport router?? That is the one you should create the new connection on.
the AirPort is still not connected to my wifi.
Reset the airport router to factory and start again.
What OS exactly are running on the computer that fails??
If the Airport is more than 4 years old it might be faulty.. did you test it with other clients.. is it only the one computer that is failing??
Have you run hardware or wireless diagnostics on the computer to make sure it is not hardware on the computer? -
Iphone4 Hotspot trouble with WIFI
When I turn on my iphone4 hotspot to broadcast WIFI I have no trouble connecting my laptop to the WIFI signal and everything works great. After about maybe 15 minutes or so, my laptop loses the connection and no longer "sees" the WIFI (phone and laptop sitting 3 ft away). When I look at the phone it still says "Personal Hotspot - 1 Connection" but the phone is no longer sending the WIFI signal. Anyone else having this trouble? I tried it again and again but see the same result.
Hello Othello1 and welcome to the BlackBerry® Support Community Forums.
Sorry to hear you are having Wi-Fi® issues with your BlackBerry® Curve™ 8520 smartphone.
Have you tried rebooting your router and modem? If you connect to another Wi-Fi network does this same thing happen?
Have a look at KB13299 "Use the Wi-Fi Diagnostics tool" when these apps seem to stop running.
Let me know how you make out.
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)! -
I am having trouble publishing my web to an FTP server using my wifi connection. It did work once but now will not through my wifi connection. I hooked up to the ethernet port of the wifi router and it published quickly. Is there a setting to change on sharing or on the firewall to allow the wifi publishing?
The Nokia Xpress browser (and all other apps) work here with Mobile Data = Off in my Nokia 210 Firmware V 06.09. Sounds like your Nokia has choosen the wrong configuration settings. Please, go to
Nokia 210 » Menu » Settings » Configuration » Personal » (Options ») Add » not Web but Access-Point » Access-Point Settings » Bearer Settings » Mobile-Data Access-Point » payandgo
Nokia 210 » Menu » Settings » Configuration » Personal » (Options ») Add » not Access-Point but this time Web (just create it, nothing to change)
Nokia 210 » Menu » Settings » Configuration » Activate » (SIM1 ») Web = My web and Access-Point = My access-point
This should enable Wi-Fi for HTTP traffic (and HTTPs traffic). Nokia Xpress uses HTTPs as connection mehtod. Because of that, the Nokia Xpress browser should use Wi-Fi as (first) preferred connection now. And because of that, the Mobile-Data settings should not matter anymore, except when you are on the go (leaving your home and your Wi-Fi). Did that help? -
I'm trying to set up my wifi and my sound. I searched the arch wiki and arch linux forums for the past few days and couldn't find a solution.
When I input #dhcpcd wlan0 I receive
wlan0: waiting for carrier
timed out
My output for $lspci | grep -i net
02:00,0 Network Controller: Realtek Semiconductor Co., Ltd. device 8723
03:00,2 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 0a)
I had to install the drivers manually with an ethernet connection from http://askubuntu.com/questions/139632/wireless-card-realtek-rtl8723ae-bt-is-not-recognized. I followed their instructions and managed to install the drivers.
#netcfg Brandon
Brandon [BUSY]
WPA Authentication/Association Failed [FAIL]
even though I have an open network.
When I tried the Arch Wiki manual wireless setup, the timed out message appeared. I tried Mode: Managed and Mode: Ad-Hoc, but was unable to change the Mode into auto with "#iwconfig wlan0 channel auto" for some reason.
#iwconfig
eth0 no wireless extensions
lo no wireless extenstions
wlan0 IEEE 802.11bgn ESSID off/any Mode: Managed Access Point: Not-Associated Tx-Powe=20 dBm
Retry long limit:7 RTS thr=2347 B Fragment thr: off
Encryption key: off
Power Management: off
I can associated the wlan0 with #iwconfig wlan0 essid Brandon but it still gives the timed out message when waiting for carrier.
Last edited by kenshin421 (2012-08-07 03:06:51)wlan0 IEEE 802.11bgn ESSID:"Brandon"
Mode:Managed Frequency:2.452 GHz Access Point: 00:22:6B:54:E8:E8
Bit Rate=7.2 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr=2347 B Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=56/70 Signal level=-54 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
That is a successful association !
I still received a timed out message when attempting dhcpcd wlan0.
With the iwconfig output above ? It should not do that.
What happens (when you are associated) with dhcpcd -B -d wlan0 ?? edit As root
Last edited by ewaller (2012-08-07 05:17:32) -
Trouble with LAMP setup on Linode...
Hey everyone,
So I followed this guide : https://www.linode.com/docs/websites/la … arch-linux
But for some reason, every time I try to naviage to the IP address in my browser, I keep getting a 403 error, that either there is no index.html or there is a read protection.
Here's my /etc/httpd/conf/httpd.conf
# This is the main Apache HTTP server configuration file. It contains the
# configuration directives that give the server its instructions.
# See <URL:http://httpd.apache.org/docs/2.4/> for detailed information.
# In particular, see
# <URL:http://httpd.apache.org/docs/2.4/mod/directives.html>
# for a discussion of each configuration directive.
# Do NOT simply read the instructions in here without understanding
# what they do. They're here only as hints or reminders. If you are unsure
# consult the online docs. You have been warned.
# Configuration and logfile names: If the filenames you specify for many
# of the server's control files begin with "/" (or "drive:/" for Win32), the
# server will use that explicit path. If the filenames do *not* begin
# with "/", the value of ServerRoot is prepended -- so "logs/access_log"
# with ServerRoot set to "/usr/local/apache2" will be interpreted by the
# server as "/usr/local/apache2/logs/access_log", whereas "/logs/access_log"
# will be interpreted as '/logs/access_log'.
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
# Do not add a slash at the end of the directory path. If you point
# ServerRoot at a non-local disk, be sure to specify a local disk on the
# Mutex directive, if file-based mutexes are used. If you wish to share the
# same ServerRoot for multiple httpd daemons, you will need to change at
# least PidFile.
ServerRoot "/etc/httpd"
# Mutex: Allows you to set the mutex mechanism and mutex file directory
# for individual mutexes, or change the global defaults
# Uncomment and change the directory if mutexes are file-based and the default
# mutex file directory is not on a local disk or is not appropriate for some
# other reason.
# Mutex default:/run/httpd
# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses.
#Listen 12.34.56.78:80
Listen 80
# Dynamic Shared Object (DSO) Support
# To be able to use the functionality of a module which was built as a DSO you
# have to place corresponding `LoadModule' lines at this location so the
# directives contained in it are actually available _before_ they are used.
# Statically compiled modules (those listed by `httpd -l') do not need
# to be loaded here.
# Example:
# LoadModule foo_module modules/mod_foo.so
LoadModule authn_file_module modules/mod_authn_file.so
#LoadModule authn_dbm_module modules/mod_authn_dbm.so
#LoadModule authn_anon_module modules/mod_authn_anon.so
#LoadModule authn_dbd_module modules/mod_authn_dbd.so
#LoadModule authn_socache_module modules/mod_authn_socache.so
LoadModule authn_core_module modules/mod_authn_core.so
LoadModule authz_host_module modules/mod_authz_host.so
LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
LoadModule authz_user_module modules/mod_authz_user.so
#LoadModule authz_dbm_module modules/mod_authz_dbm.so
#LoadModule authz_owner_module modules/mod_authz_owner.so
#LoadModule authz_dbd_module modules/mod_authz_dbd.so
LoadModule authz_core_module modules/mod_authz_core.so
#LoadModule authnz_ldap_module modules/mod_authnz_ldap.so
LoadModule access_compat_module modules/mod_access_compat.so
LoadModule auth_basic_module modules/mod_auth_basic.so
#LoadModule auth_form_module modules/mod_auth_form.so
#LoadModule auth_digest_module modules/mod_auth_digest.so
#LoadModule allowmethods_module modules/mod_allowmethods.so
#LoadModule file_cache_module modules/mod_file_cache.so
#LoadModule cache_module modules/mod_cache.so
#LoadModule cache_disk_module modules/mod_cache_disk.so
#LoadModule cache_socache_module modules/mod_cache_socache.so
#LoadModule socache_shmcb_module modules/mod_socache_shmcb.so
#LoadModule socache_dbm_module modules/mod_socache_dbm.so
#LoadModule socache_memcache_module modules/mod_socache_memcache.so
#LoadModule watchdog_module modules/mod_watchdog.so
#LoadModule macro_module modules/mod_macro.so
#LoadModule dbd_module modules/mod_dbd.so
#LoadModule dumpio_module modules/mod_dumpio.so
#LoadModule echo_module modules/mod_echo.so
#LoadModule buffer_module modules/mod_buffer.so
#LoadModule data_module modules/mod_data.so
#LoadModule ratelimit_module modules/mod_ratelimit.so
LoadModule reqtimeout_module modules/mod_reqtimeout.so
#LoadModule ext_filter_module modules/mod_ext_filter.so
#LoadModule request_module modules/mod_request.so
LoadModule include_module modules/mod_include.so
LoadModule filter_module modules/mod_filter.so
#LoadModule reflector_module modules/mod_reflector.so
#LoadModule substitute_module modules/mod_substitute.so
#LoadModule sed_module modules/mod_sed.so
#LoadModule charset_lite_module modules/mod_charset_lite.so
#LoadModule deflate_module modules/mod_deflate.so
#LoadModule xml2enc_module modules/mod_xml2enc.so
#LoadModule proxy_html_module modules/mod_proxy_html.so
LoadModule mime_module modules/mod_mime.so
#LoadModule ldap_module modules/mod_ldap.so
LoadModule log_config_module modules/mod_log_config.so
#LoadModule log_debug_module modules/mod_log_debug.so
#LoadModule log_forensic_module modules/mod_log_forensic.so
#LoadModule logio_module modules/mod_logio.so
#LoadModule lua_module modules/mod_lua.so
LoadModule env_module modules/mod_env.so
#LoadModule mime_magic_module modules/mod_mime_magic.so
#LoadModule cern_meta_module modules/mod_cern_meta.so
#LoadModule expires_module modules/mod_expires.so
LoadModule headers_module modules/mod_headers.so
#LoadModule ident_module modules/mod_ident.so
#LoadModule usertrack_module modules/mod_usertrack.so
#LoadModule unique_id_module modules/mod_unique_id.so
LoadModule setenvif_module modules/mod_setenvif.so
LoadModule version_module modules/mod_version.so
#LoadModule remoteip_module modules/mod_remoteip.so
LoadModule php5_module modules/libphp5.so
LoadModule proxy_module modules/mod_proxy.so
LoadModule proxy_connect_module modules/mod_proxy_connect.so
LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
LoadModule proxy_http_module modules/mod_proxy_http.so
LoadModule proxy_fcgi_module modules/mod_proxy_fcgi.so
LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
#LoadModule proxy_fdpass_module modules/mod_proxy_fdpass.so
LoadModule proxy_wstunnel_module modules/mod_proxy_wstunnel.so
LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
LoadModule proxy_express_module modules/mod_proxy_express.so
#LoadModule session_module modules/mod_session.so
#LoadModule session_cookie_module modules/mod_session_cookie.so
#LoadModule session_crypto_module modules/mod_session_crypto.so
#LoadModule session_dbd_module modules/mod_session_dbd.so
LoadModule slotmem_shm_module modules/mod_slotmem_shm.so
#LoadModule slotmem_plain_module modules/mod_slotmem_plain.so
#LoadModule ssl_module modules/mod_ssl.so
#LoadModule dialup_module modules/mod_dialup.so
LoadModule lbmethod_byrequests_module modules/mod_lbmethod_byrequests.so
LoadModule lbmethod_bytraffic_module modules/mod_lbmethod_bytraffic.so
LoadModule lbmethod_bybusyness_module modules/mod_lbmethod_bybusyness.so
LoadModule lbmethod_heartbeat_module modules/mod_lbmethod_heartbeat.so
#LoadModule mpm_event_module modules/mod_mpm_event.so
LoadModule mpm_prefork_module modules/mod_mpm_prefork.so
#LoadModule mpm_worker_module modules/mod_mpm_worker.so
LoadModule unixd_module modules/mod_unixd.so
#LoadModule heartbeat_module modules/mod_heartbeat.so
#LoadModule heartmonitor_module modules/mod_heartmonitor.so
#LoadModule dav_module modules/mod_dav.so
LoadModule status_module modules/mod_status.so
LoadModule autoindex_module modules/mod_autoindex.so
#LoadModule asis_module modules/mod_asis.so
#LoadModule info_module modules/mod_info.so
#LoadModule suexec_module modules/mod_suexec.so
#LoadModule cgid_module modules/mod_cgid.so
#LoadModule cgi_module modules/mod_cgi.so
#LoadModule dav_fs_module modules/mod_dav_fs.so
#LoadModule dav_lock_module modules/mod_dav_lock.so
#LoadModule vhost_alias_module modules/mod_vhost_alias.so
LoadModule negotiation_module modules/mod_negotiation.so
LoadModule dir_module modules/mod_dir.so
#LoadModule imagemap_module modules/mod_imagemap.so
#LoadModule actions_module modules/mod_actions.so
#LoadModule speling_module modules/mod_speling.so
LoadModule userdir_module modules/mod_userdir.so
LoadModule alias_module modules/mod_alias.so
#LoadModule rewrite_module modules/mod_rewrite.so
<IfModule unixd_module>
# If you wish httpd to run as a different user or group, you must run
# httpd as root initially and it will switch.
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
User http
Group http
</IfModule>
# 'Main' server configuration
# The directives in this section set up the values used by the 'main'
# server, which responds to any requests that aren't handled by a
# <VirtualHost> definition. These values also provide defaults for
# any <VirtualHost> containers you may define later in the file.
# All of these directives may appear inside <VirtualHost> containers,
# in which case these default settings will be overridden for the
# virtual host being defined.
# ServerAdmin: Your address, where problems with the server should be
# e-mailed. This address appears on some server-generated pages, such
# as error documents. e.g. [email protected]
ServerAdmin [email protected]
# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
# If your host doesn't have a registered DNS name, enter its IP address here.
#ServerName www.example.com:80
# Deny access to the entirety of your server's filesystem. You must
# explicitly permit access to web content directories in other
# <Directory> blocks below.
<Directory />
AllowOverride none
Require all denied
</Directory>
# Note that from this point forward you must specifically allow
# particular features to be enabled - so if something's not working as
# you might expect, make sure that you have specifically enabled it
# below.
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
DocumentRoot "/srv/http/default"
<Directory "/srv/http/default">
# Possible values for the Options directive are "None", "All",
# or any combination of:
# Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
# Note that "MultiViews" must be named *explicitly* --- "Options All"
# doesn't give it to you.
# The Options directive is both complicated and important. Please see
# http://httpd.apache.org/docs/2.4/mod/core.html#options
# for more information.
Options Indexes FollowSymLinks
# AllowOverride controls what directives may be placed in .htaccess files.
# It can be "All", "None", or any combination of the keywords:
# AllowOverride FileInfo AuthConfig Limit
AllowOverride None
# Controls who can get stuff from this server.
Require all granted
</Directory>
# DirectoryIndex: sets the file that Apache will serve if a directory
# is requested.
<IfModule dir_module>
DirectoryIndex index.html
</IfModule>
# The following lines prevent .htaccess and .htpasswd files from being
# viewed by Web clients.
<Files ".ht*">
Require all denied
</Files>
# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here. If you *do* define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
ErrorLog "/var/log/httpd/error_log"
# LogLevel: Control the number of messages logged to the error_log.
# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
LogLevel warn
<IfModule log_config_module>
# The following directives define some format nicknames for use with
# a CustomLog directive (see below).
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
LogFormat "%h %l %u %t \"%r\" %>s %b" common
<IfModule logio_module>
# You need to enable mod_logio.c to use %I and %O
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
</IfModule>
# The location and format of the access logfile (Common Logfile Format).
# If you do not define any access logfiles within a <VirtualHost>
# container, they will be logged here. Contrariwise, if you *do*
# define per-<VirtualHost> access logfiles, transactions will be
# logged therein and *not* in this file.
CustomLog "/var/log/httpd/access_log" common
# If you prefer a logfile with access, agent, and referer information
# (Combined Logfile Format) you can use the following directive.
#CustomLog "/var/log/httpd/access_log" combined
</IfModule>
<IfModule alias_module>
# Redirect: Allows you to tell clients about documents that used to
# exist in your server's namespace, but do not anymore. The client
# will make a new request for the document at its new location.
# Example:
# Redirect permanent /foo http://www.example.com/bar
# Alias: Maps web paths into filesystem paths and is used to
# access content that does not live under the DocumentRoot.
# Example:
# Alias /webpath /full/filesystem/path
# If you include a trailing / on /webpath then the server will
# require it to be present in the URL. You will also likely
# need to provide a <Directory> section to allow access to
# the filesystem path.
# ScriptAlias: This controls which directories contain server scripts.
# ScriptAliases are essentially the same as Aliases, except that
# documents in the target directory are treated as applications and
# run by the server when requested rather than as documents sent to the
# client. The same rules about trailing "/" apply to ScriptAlias
# directives as to Alias.
ScriptAlias /cgi-bin/ "/srv/http/cgi-bin/"
</IfModule>
<IfModule cgid_module>
# ScriptSock: On threaded servers, designate the path to the UNIX
# socket used to communicate with the CGI daemon of mod_cgid.
#Scriptsock cgisock
</IfModule>
# "/srv/http/cgi-bin" should be changed to whatever your ScriptAliased
# CGI directory exists, if you have that configured.
<Directory "/srv/http/cgi-bin">
AllowOverride None
Options None
Require all granted
</Directory>
<IfModule mime_module>
# TypesConfig points to the file containing the list of mappings from
# filename extension to MIME-type.
TypesConfig conf/mime.types
# AddType allows you to add to or override the MIME configuration
# file specified in TypesConfig for specific file types.
#AddType application/x-gzip .tgz
# AddEncoding allows you to have certain browsers uncompress
# information on the fly. Note: Not all browsers support this.
#AddEncoding x-compress .Z
#AddEncoding x-gzip .gz .tgz
# If the AddEncoding directives above are commented-out, then you
# probably should define those extensions to indicate media types:
AddType application/x-compress .Z
AddType application/x-gzip .gz .tgz
AddType application/x-httpd-php .php
AddType application/x-httpd-php-source .phps
# AddHandler allows you to map certain file extensions to "handlers":
# actions unrelated to filetype. These can be either built into the server
# or added with the Action directive (see below)
# To use CGI scripts outside of ScriptAliased directories:
# (You will also need to add "ExecCGI" to the "Options" directive.)
#AddHandler cgi-script .cgi
# For type maps (negotiated resources):
#AddHandler type-map var
# Filters allow you to process content before it is sent to the client.
# To parse .shtml files for server-side includes (SSI):
# (You will also need to add "Includes" to the "Options" directive.)
#AddType text/html .shtml
#AddOutputFilter INCLUDES .shtml
</IfModule>
# The mod_mime_magic module allows the server to use various hints from the
# contents of the file itself to determine its type. The MIMEMagicFile
# directive tells the module where the hint definitions are located.
#MIMEMagicFile conf/magic
# Customizable error responses come in three flavors:
# 1) plain text 2) local redirects 3) external redirects
# Some examples:
#ErrorDocument 500 "The server made a boo boo."
#ErrorDocument 404 /missing.html
#ErrorDocument 404 "/cgi-bin/missing_handler.pl"
#ErrorDocument 402 http://www.example.com/subscription_info.html
# MaxRanges: Maximum number of Ranges in a request before
# returning the entire resource, or one of the special
# values 'default', 'none' or 'unlimited'.
# Default setting is to accept 200 Ranges.
#MaxRanges unlimited
# EnableMMAP and EnableSendfile: On systems that support it,
# memory-mapping or the sendfile syscall may be used to deliver
# files. This usually improves server performance, but must
# be turned off when serving from networked-mounted
# filesystems or if support for these functions is otherwise
# broken on your system.
# Defaults: EnableMMAP On, EnableSendfile Off
#EnableMMAP off
#EnableSendfile on
# Supplemental configuration
# The configuration files in the conf/extra/ directory can be
# included to add extra features or to modify the default configuration of
# the server, or you may simply copy their contents here and change as
# necessary.
# Server-pool management (MPM specific)
Include conf/extra/httpd-mpm.conf
# Multi-language error messages
Include conf/extra/httpd-multilang-errordoc.conf
# Fancy directory listings
Include conf/extra/httpd-autoindex.conf
# Language settings
Include conf/extra/httpd-languages.conf
# User home directories
#Include conf/extra/httpd-userdir.conf
# Real-time info on requests and configuration
#Include conf/extra/httpd-info.conf
# Virtual hosts
Include conf/extra/httpd-vhosts.conf
# Local access to the Apache HTTP Server Manual
#Include conf/extra/httpd-manual.conf
# Distributed authoring and versioning (WebDAV)
#Include conf/extra/httpd-dav.conf
# Various default settings
Include conf/extra/httpd-default.conf
Include conf/extra/php5_module.conf
# Configure mod_proxy_html to understand HTML4/XHTML1
<IfModule proxy_html_module>
Include conf/extra/proxy-html.conf
</IfModule>
# Secure (SSL/TLS) connections
#Include conf/extra/httpd-ssl.conf
# Note: The following must must be present to support
# starting without SSL on platforms with no /dev/random equivalent
# but a statically compiled-in mod_ssl.
<IfModule ssl_module>
SSLRandomSeed startup builtin
SSLRandomSeed connect builtin
</IfModule>
# uncomment out the below to deal with user agents that deliberately
# violate open standards by misusing DNT (DNT *must* be a specific
# end-user choice)
#<IfModule setenvif_module>
#BrowserMatch "MSIE 10.0;" bad_DNT
#</IfModule>
#<IfModule headers_module>
#RequestHeader unset DNT env=bad_DNT
#</IfModule>
IncludeOptional conf/sites-enabled/*.conf
IncludeOptional conf/mods-enabled/*.conf
Here's my /etc/httpd/conf/extra/httpd-vhosts.conf
# Virtual Hosts
# Required modules: mod_log_config
# If you want to maintain multiple domains/hostnames on your
# machine you can setup VirtualHost containers for them. Most configurations
# use only name-based virtual hosts so the server doesn't need to worry about
# IP addresses. This is indicated by the asterisks in the directives below.
# Please see the documentation at
# <URL:http://httpd.apache.org/docs/2.4/vhosts/>
# for further details before you try to setup virtual hosts.
# You may use the command line option '-S' to verify your virtual host
# configuration.
# VirtualHost example:
# Almost any Apache directive may go into a VirtualHost container.
# The first VirtualHost section is used for all requests that do not
# match a ServerName or ServerAlias in any <VirtualHost> block.
<VirtualHost *:80>
ServerAdmin [email protected]
DocumentRoot "/etc/httpd/docs/dummy-host.example.com"
ServerName dummy-host.example.com
ServerAlias www.dummy-host.example.com
ErrorLog "/var/log/httpd/dummy-host.example.com-error_log"
CustomLog "/var/log/httpd/dummy-host.example.com-access_log" common
</VirtualHost>
<VirtualHost *:80>
ServerAdmin [email protected]
DocumentRoot "/etc/httpd/docs/dummy-host2.example.com"
ServerName dummy-host2.example.com
ErrorLog "/var/log/httpd/dummy-host2.example.com-error_log"
CustomLog "/var/log/httpd/dummy-host2.example.com-access_log" common
</VirtualHost>
<VirtualHost *:80>
ServerAdmin my_email_address
ServerName li165-35.members.linode.com
ServerAlias www.li165-35.members.linode.com
DocumentRoot /srv/http/li165-35.members.linode.com/public_html/
ErrorLog /srv/http/li165-35.members.linode.com/logs/error.log
CustomLog /srv/http/li165-35.members.linode.com/logs/access.log combined
<Directory />
Order deny,allow
Allow from all
Require all granted
</Directory>
</VirtualHost>
I used chown/chgrp -R http to make sure everything in /srv/http was managed by http.
What am I doing wrong? Also, that's my FQDN. I'm not sure if it's insecure or not to post that. I mean, I want people to visit the site.
I also put a index.html in my /srv/http/default and /srv/httpd/li.../public_html folders.
index.html :
<html>
<head />
<body>
<p>Hello, world!</p>
</body>
</html>
I will say this, I don't have any DNS type stuff set-up. I don't even know what that is (I know, I should read up).
But even if I type in just the IP, I still get the permission error.
Edit : I'm an idiot! The link actually works! The IP itself fails but the url I posted for the virtual host works! The FQDN actually works. Omg. Is this because I updated the /etc/hosts file on MY system to recognize the FQDN with the IP?
Last edited by MutantJohn (2015-01-21 19:03:43)after I downloaded the 10.8 Mac OS I could not open the Cisco Connect Software. I went to chat with the customer support people and they beat me around the bush and they knew that it was not compatible with 10.8 Spoke with two different people, asked a crazy amount of questions about the router and the connection but in the end of the hour plus convo with them they said it was not compatible when they know all along. I mean, come on I can not be the first person with this problem.
-
Trouble with wifi after upgrade to IOS 8
After upgrading my iPad 3 to Ios 8 yesterday I am having trouble of connecting to the internet using the wireless wifi modem on MacBook Pro. The Wifi appears to connect to the iPad but I get a message '"MacBook Pro" is Not Connected to the Internet" when I start the process of connecting to my MacBook. I join anyway but I don't see the WiFi icon on top of my iPad even though I have a tick next to the connection on the settings page. Does anyone have any idea how I get the Wifi working again?
My problem turned out to be that the Sharing app decided to make the newly discovered Thunderbolt Bridge the default device to be used for sharing rather than my USB modem. Changing back to the original setting and everything is working again.
-
Hello everyone, recently I have been having numerous issues with my WiFi connection. I am only noticing the issue when I am attempting to download a file via Firefox or using wget. What will happen is, during the middle of downloading the file my internet will suddenly quit working. I checked into the dmesg log and noticed a huge flood of " iwlwifi 5:00.0: fail to flush all tx fifo queues". I'm not entirely sure what this means but the only way to fix the issue is to reboot my entire system and cross my fingers hoping it wont happen again when I attempt to download something.
Can anyone provide a little bit of insight into the issue? Has anyone else had similar problems? I have attempted researching the issue on google but I have had no luck finding good results. If anyone needs a little more info, please let me know I will be more than helpful to assist those who are willing to help with my issue. Thanks in advance!
My network card is (taken from lspci): Network controller: Intel Corporation Ultimate N WiFi Link 5300
(I did not have to install any special drivers for this, it was working automatically.)
EDIT: Here is a picture of my log output from KSystemLog. http://imageshack.us/a/img805/3858/errorui.png
Last edited by dshelley (2012-10-17 16:04:05)WonderWoofy wrote:
Instead of rebooting, why not simple unload the module and then reload it again.
No idea how to solve it, but I think rebooting is unnecessary.
Thanks for the reply WonderWoofy. I have been able to unload the module's and reload them and this does appear to work as a temporary fix to the issue instead of completely rebooting! Although, I am still having problems.
I can have the WiFi work fine with normal web browsing and low latency activities, but the moment I start downloading a file (multiple files at once cause the issues to happen even faster) the iwlwifi module spits out a long dmesg log of: "iwlwifi 0000:05:00.0: fail to flush all tx fifo queues".
I am still looking into the issue and I want to see if I'm able to debug the module my self. Although, for now I have an alias script that will unload and reload the failed modules instead, just for a temporary fix. Again, if anyone needs more info please let me know I'll be happy to share! Thanks for the help! -
Hi I have a mac book pro OSX 10.8.4 iv connected to a wifi point where I am staying and iv selected network and put in password and over the wifi symbol a exclamation mark appears the wifi works perfectly on my iPhone but won't with my MacBook iv turned it off and on iv tried to forget/delete the network but it won't let me? Is there anything I can do I really need it cause I'm travelling and need to book things. Thanks
Information.
Wireless Connection Problems - Fix
Wireless Connection Problems - Fix (2)
Wireless Connection Problems - Fix (3)
Wireless Connection Problems - Fix (4)
Wireless Diagnostics - About -
Trouble with wifi and swtiching to 4g networks
I having problems with iphone 5 and network issues. While on wi-fi is constantly turning on adn off adn it is frustating.. when not in wi-fi.. it basically does not do nothing.... I dont get to see the 4G
The dns (domain name server) address is found by choosing settings -> wifi -> your network.
Then tap on the blue circle with the arrow on the right side.
Scroll down until you find router and dns.
If the dns is blank or showing the same as your router address, this could be causing the problem.
What you could do is contact your isp and ask them what there dns address should be, then enter that into the iphone and see if it works.
Hope this helps. -
Why have i trouble with wifi internet on my iphone 4 and sometimes on my ipad 3?
Internet conection are suddenly for some days now unvaivable. I have internets to choose from in the internetlist, but the iphone cant connect. And now my ipad also starting to do the same thing nd i hve to restart it. Im uing the 6.0.1 IOS. Iphone only show the E.
Just because some devices (particularly devices with constant power) continue to work does not mean your WiFi router is working properly. Powered devices almost never request new IP addresses via DHCP which may be where your problem lies.
Try restarting your router to see if that helps (this will restart the router DHCP deamon which may have crashed or hung).
To rule out iPhone problems test it on other networks. If it can't connect there then it may have a hardware problem.
Since in your original post you stated that you have been having problems with two mobile devices this makes your router very suspect.
Maybe you are looking for
-
I was tracking my stolen phone, then the phone must have been switched off, it says on icloud that the phone is offline, i have cancelled my sim card so i dont get any charges, my phone had a passcode on it, if someone whipes the phone and tries to u
-
Keywords on external Hard drive
I spent a good part of a day adding keywords to my entire library on my external hard drive using my desktop. When Im away and using the same hard drive connected to my laptop the keywords I imported from my desktop no longer match up to the photo's
-
Workitem is not removed from User Inbox
Hi, There is requirement, when the PR is created by user, first it has to go his department Head and then to Manager, AGM, GM, etc. There are different departments. I'm maintaining organizational structure and giving positions in Release Strategy. No
-
Vendor EDI invoice // More options in OBCD
Hi, SAP standard OBCD or table T07M does not have much option and new fields can also not be added for more options in determination of tax code from different ship-from-country . Like to know the possible ways to do it. With regards, Mrinal
-
ABAP dump when running an ALV report in a portal
Hi, I have an ABAP report created in SAP R/3 4.7. Am using the ALV function module REUSE_ALV_GRID_DISPLAY to display the output. The programs runs correctly when run in R/3 using the SAP GUI. When the report is run in the portal, I get a runtime