Trunk between 4500-X and 4507R not working

Hi all,
i have got a new switch (4500-X) which i would like to connect to our existing 4507R switch. So i configured trunk ports on each of them, like i do this with all of my other access switches. I tried so many things, but i cant reach vlans from the new switch and iam totaly out of ideas
Iam quite sure that i make a verry dump config issue, but i cant fine the fault in my config...hopyfully someone could please help me? I hope this is the right information you need.
Many many Thanks!
The "OLD" Switch (4507R):
OLD#sh ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(54)SG, RELEASE SOFTWARE (fc3)
OLD#sh run int gi3/6
Building configuration...
Current configuration : 149 bytes
interface GigabitEthernet3/6
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
end
OLD#sh int gi3/6 switch
Name: Gi3/6
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Off
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Administrative Native VLAN tagging: enabled
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk associations: none
Administrative private-vlan trunk mappings: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none
OLD#sh int gi3/6 trunk
Port        Mode             Encapsulation  Status        Native vlan
Gi3/6       on               802.1q         trunking      1
Port        Vlans allowed on trunk
Gi3/6       1-4094
Port        Vlans allowed and active in management domain
Gi3/6       1-3,9-10,20,23-24,26,32-40,66-68,95-101,110-111,120,200,500-501,510,995-999
Port        Vlans in spanning tree forwarding state and not pruned
Gi3/6       1
The "NEW" Switch (4500-X):
NEW#sh ver
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.04.00.SG RELEASE SOFTWARE (fc3)
NEW#sh run int te1/32
Building configuration...
Current configuration : 94 bytes
interface TenGigabitEthernet1/32
switchport mode trunk
end
NEW#sh int te1/32 switchport
Name: Te1/32
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Administrative Native VLAN tagging: enabled
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk associations: none
Administrative private-vlan trunk mappings: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none
NEW#sh int te1/32 trun
Port        Mode             Encapsulation  Status        Native vlan
Te1/32      on               802.1q         trunking      1
Port        Vlans allowed on trunk
Te1/32      1-4094
Port        Vlans allowed and active in management domain
Te1/32      1-3,9-10,20,23-24,26,32-40,66-68,95-101,110-111,120,200,500-501,510,995-999
Port        Vlans in spanning tree forwarding state and not pruned
Te1/32      1-3,9-10,20,23-24,26,32-40,66-68,95-101,110-111,120,200,500-501,510,995-999

Hi!
Yes, sure:
######### OLD ##########
OLD#sh spanning-tree vlan 3
VLAN0003
  Spanning tree enabled protocol ieee
  Root ID    Priority    32771
             Address     000c.30b1.7540
             This bridge is the root
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
  Bridge ID  Priority    32771  (priority 32768 sys-id-ext 3)
             Address     000c.30b1.7540
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
             Aging Time  300 sec
Interface           Role Sts Cost      Prio.Nbr Type
Gi3/5               Desg FWD 4         128.133  P2p
Gi3/6               Desg FWD 4         128.134  P2p
Gi4/2               Desg FWD 4         128.194  P2p
Gi4/3               Desg FWD 4         128.195  P2p
Gi5/1               Desg FWD 4         128.257  P2p
Gi5/3               Desg FWD 4         128.259  P2p
Gi5/4               Desg FWD 4         128.260  P2p
Gi5/5               Desg FWD 4         128.261  P2p
Gi5/6               Desg FWD 4         128.262  P2p
Gi6/1               Desg FWD 4         128.321  P2p
Gi6/2               Desg FWD 4         128.322  P2p
Gi6/3               Desg FWD 4         128.323  P2p
Gi6/5               Desg FWD 4         128.325  P2p
Gi6/6               Desg FWD 4         128.326  P2p
Gi7/1               Desg FWD 4         128.385  P2p
Gi7/2               Desg FWD 4         128.386  P2p
Gi7/4               Desg FWD 4         128.388  P2p
Gi7/5               Desg FWD 4         128.389  P2p
Gi7/6               Desg FWD 4         128.390  P2p
Po3                 Desg FWD 3         128.643  P2p
Po6                 Desg FWD 3         128.646  P2p
Po7                 Desg FWD 3         128.647  P2p
OLD#sh int gi3/6
GigabitEthernet3/6 is up, line protocol is up (connected)
  Hardware is Gigabit Ethernet Port, address is 0016.9dd4.1fe7 (bia 0016.9dd4.1fe7)
  Description: trunk core NEU
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 1000Mb/s, link type is auto, media type is 1000BaseSX
  Media-type configured as SFP connector
  input flow-control is on, output flow-control is off
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:04, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 9000 bits/sec, 16 packets/sec
     809802 packets input, 156747108 bytes, 0 no buffer
     Received 809180 broadcasts (809157 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     77368681 packets output, 5652973144 bytes, 0 underruns
     0 output errors, 0 collisions, 3 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
######### NEW ##########
NEW#sh spanning-tree vlan 3
VLAN0003
  Spanning tree enabled protocol ieee
  Root ID    Priority    32771
             Address     000c.30b1.7540
             Cost        4
             Port        32 (TenGigabitEthernet1/32)
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
  Bridge ID  Priority    32771  (priority 32768 sys-id-ext 3)
             Address     f872.ead8.4400
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
             Aging Time  300 sec
Interface           Role Sts Cost      Prio.Nbr Type
Te1/32              Root FWD 4         128.32   P2p
NEW#sh int ten 1/32
TenGigabitEthernet1/32 is up, line protocol is up (connected)
  Hardware is Ten Gigabit Ethernet Port, address is f872.ead8.441f (bia f872.ead8.441f)
  Description: trunk sw99rz1-1-1
  MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 1000Mb/s, link type is auto, media type is 1000BaseSX
  input flow-control is on, output flow-control is on
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 13000 bits/sec, 18 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     365663 packets input, 26752705 bytes, 0 no buffer
     Received 365496 broadcasts (363520 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     3843 packets output, 745065 bytes, 0 underruns
     0 output errors, 0 collisions, 3 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
Thanks a lot!
tobias

Similar Messages

  • UFT 11.53 - toggle between keyword view and editor not working

    Hello,
      I have installed the enterprise version of UFT 11.53.  I have patched it with Patch # 3 (00082) and Patch # 4 (00106) in order to get Chome v 37 support.  Now when I try to toggle between keyword View and editor, it is not working.  The editor is fine.  The Keyword just set frozen and will not allow me to do anything other than, change it back to the editor
    see when I click the toggle button...its frozen...see the toggle button is down.
    It's so annoying.  I'm going to have to uninstall it again.
    Please help, if you know what's going on

    Hello sfarren,
    The forum you want is the HP Enterprise Business Community.
    Right now you are in the consumer products forum.
    I am guessing this link is the area you will want to ask your question at.
    http://h30499.www3.hp.com/t5/Unified-Functional-Testing/bd-p/sws-Fun_TEST_SF
    Good luck and hope it helps.
    PS: You might have to register again to post on that forum.

  • Screen Sharing between Snow Leopard and Leopard not working

    I have Leopard on my old G5 Tower and just put Snow on my Intel Mini now Screen Sharing no longer works, file sharing works my network drives chatter back and forth with no problems I just can't get a Screen Share connection. On the G5 I put in the mini's location the "communicating" barber pole churns away for about 2mins then comes back with "Connection failed. Please make sure that Screen Sharing is enabled on the computer..... Also make sure your network connection is working properly. On the Mini Screen Sharing either crashes on launch or when it does launch does the same thing as the G5. Screen Sharing is on on both machines. I was using it just mins. before installing Snow on the Mini. I did install the remote desktop update from Apple on the Mini, it seems to be for Snow only as the update isn't mentioned on Software Update on the Leopard G5. So I'm thinking of going back to Leopard on the Mini, can I do it by just doing a "restore" from Time Machine or should I dig out the old install disk?
    Am I the only one out there with this problem?
    Netgear router on wired Gigabit Ethernet Network, several Firewire drives, and Network Storage drives.

    The G5 is running 10.5.8 with all the updates. Screen sharing on the Mini 9 times out of 10 crashes on launch when it does load the computer list shows but none on it can be selected and connected to as before. When I put the G5's name in and try to connect I get the same cannot connect make sure sharing is on message I get on the G5 trying to connect to the Mini. I have tried making new network settings and rebooting that didn't work. File sharing works works fine all network drives show up. This and Front Row being now slow jerky and audio being out of sync (I've seen this complaint else where on this forum) are the only problems I've found. But these two are just enough to send me back to Leopard on the Mini. It is my media server. I don't use iChat but I did check to see if Screen Sharing is on after it finally opened, crashed over and over, I see that it was enabled there as well. My network is wired not airport, I only use wifi for my iPod Touch.

  • Dynamic Link between Premire Pro and AE not working

    I've been having this issue where dynamic link is grayed out in the Premiere Pro menu, when i try to link a clip to AE. It's the same the other way round (i.e. AE to Premiere), and also the "Replace with After Effects Comp" is grayed out as well. Im using the CC version (Not CC 2014), so it should work?
    Thanks for your help!

    Hi Kevin,
    Thanks for your reply. I'm using CS6 (if that's what you mean by version - otherwise I think it's 7.0). I've never come across verifying the programs, how do I go about it?
    Thanks

  • Transfer of help between F4 Help and Application not working

    I need immediate help in determining why the F4 help for BP Search not returning the selected field to the calling application.
    After the user selects the F4 BP search help screen and performs a search the value selected is not returned and displayed in the calling application.
    What is the missing link?  Also, the field not populating was one that I added through PCUI.
    Thanks.
    Jason

    your probably best off phoning motorola because obviously theres something wrong with your phone which ony they can sort out there phone number is: 0870 9010 555
    hope you get your phone sorted and hope this is a help to you

  • Sharing Itunes library between windows desktop and macbook not working

    Hi, I just bought my laptop today. I've had it about 3 hours. I have 2147 songs on my windows itunes library, and i would love to be able to put them on the laptop too. Now, both of my computers are on the local area connection, but for some reason when i go to network places on my desktop the laptop doesnt show up. When i go to iTunes on my laptop and click import, i find my server, i find my computer, and then it asks me for a domain name, a username, and a password. I've tried multiple combinations, i'm not sure which username/pw combo its looking for but no matter what I do i get no error messages telling me i'm wrong, but absolutely nothing happens. Please help.

    This is a compleentary advice: MAKE SURE THAT WINDOWS AND MAC HAVE THE SAME GROUP NAME!
    In mac go to the preferences and activate Windows Sharing from the network.
    Then go with the finder to applications utility and Directory Access. SMB is the protocol that OS X uses to exchange with Windows. Go into its proprieties and choose the same name you have given to your windows group (USUALLY "WORKGROUP" but it may differ)
    To change the name in windows Xp is even easier. right click the m computer and choose properties and then the "Name" tag - change the group - You'll need to restart.
    Almost forgot: you have to share the Music Folder on XP to have it show up from the mac. Right click it and choose Properties - Share tab - Activate network sharing
    And remember, it is easier with a USB drive
    Message was edited by: eiapoce

  • RFC conn between SAP ERP and TREX not working

    Hi experts,
    we run a TREX instance on a Windows 2003 server and use it for our HCM portal.
    The solution is in operation since 2 years but actually we face the problem that objects which have been created within the last month will not be covered by the index.
    Without knowing about any changes in the setup I see the following error message when I perform the RFC connecten test in our ERP system:
    Logon     Connection Error
    Error Details     Error when opening an RFC connection
    Error Details     ERROR: program Trex_UKP_20071025104543 not registered
    Error Details     LOCATION: SAP-Gateway on host janos / sapgw00
    Error Details     DETAIL: TP Trex_UKP_20071025104543 not registered
    Error Details     COMPONENT: SAP-Gateway
    Error Details     COUNTER: 12906
    Error Details     MODULE: gwr3cpic.c
    Error Details     LINE: 1778
    Error Details     RETURN CODE: 679
    Error Details     SUBRC: 0
    Error Details     RELEASE: 700
    Error Details     TIME: Mon Jul 27 10:34:48 2009
    Error Details     VERSION: 2
    In the TREX admin tool on the Windows server I see the following log message:
    Source->Destination: Not set in TREX but TREX reachable -> ini file section missing?.
    After reading lots of notes I guess that I have to register the server program that's used in the RFC on the gateway.
    Unfortunately I have no idea how to do that.
    Has anybody experiences with such a problem case or can tell me how to continue?
    Is the problematic RFC realy the reason of my problem or just another side effect?
    Many thanks for your really appreciated help in advance and best regards
    Günter

    Hi again,
    the saprfc.ini on the TREX server look like follows:
    DEST=UKT
    TYPE=A
    ASHOST=medos
    SYSNR=00
    DEST=UKP
    TYPE=A
    ASHOST=janos
    SYSNR=00
    UKT is our test system which is connected to the same TREX server and everything is fine there.
    On the test system I can also see the registered server program in SMGW.
    UKP is our productive system where the configuration should be the same.
    Of course I do not see the registered server program in SMGW there.
    Is the way described in above link (RFCACCEPT) the only correct way to register my server program?
    I ask because I found information that the server program has to be developed according to this rfcaccept command and I have absolutely no idea wheather this is so.
    Thanks again for your help!
    Günter

  • Screen Sharing between Mountain Lion and Tiger not working

    rMBP running 10.8.2 ML and a G3 iMac running 10.4.11 Tiger.
    When I try and use Screen Sharing on the MBP to connect to the G3 it prompts for both a username and password. I enter a valid user and pw but it fails with
    Authenication failed to "Ruby".
    Please verify you have entered the correct name and password.
    Third-party VNC clients, e.g. JollysFastVNC on my MBP and Remoter on my iPhone, can connect fine, but they only request a password.
    Any ideas?

    I've been using Screen Share on my home network for a very long time.  My most used computer, MacBook Pro (2011) was just upgraded to ML, my desktop still has Lion on it - and can't be upgraded because it is an early MacPro.  I was having intermittant problems getting the MBPro to connect to the MPro screen, and resetting the PRAM was correcting it (but it could have been the rebooting process alone - I don't know).  Now I can share the MPro disks on my network but not the screen.  Now, to me, that's wierd.  I've tried doing all kinds of setting checks, preference removal, etc.  No luck.  I can, however (as someone above mentioned) connect from my MPro (Lion) to my MBPro (ML) screen.  I've checked my Intego VirusBarrier X6 settings, i.e. blocked addresses (in the past that has happened and blocked) and I've even entered my MBPro address into the approved address section.  I've checked/rechecked the Sharing Preferences, turned them on/off, etc.  All to no avail.
    Is this a Mountain Lion / Lion issue, a Mountain Lion issue, or something somewhere corrupt?  I used to have Remote Desktop on the MPro, but for my needs Screen Share & Disk Share suit my needs on my home network.  I have LogMeInIgnition, which when the last time I tried to connect to the MBPro it showed it offline - and it isn't.  I feel there's something in ML blocking things.
    I'm open to suggestions, and a fix if needed.  This is frustrating.  Not that I can't use the exercise to walk to the room where the MPro is - not the point. 
    Tom

  • Between dowloading issues and Java not working correctly, when the next version coming out? I'm a breath away from switching to IE

    I cannot use the Java pull down menus on USAA.com, and downloads cancel when I close Firefox and cannot be resumed. What happened to the old downloader? I have to use IE in order to use USAA.com (primary banking). I tried updating Java, I tried a reinstall on firefox, clearing my cache, everything. No dice. If a new version doesn't come out soon I'm switching to IE... I've been loyal for 10 years.

    To get the old downloader back follow the directions below.
    # In the [[Location bar autocomplete|Location bar]], type '''about:config''' and press '''Enter'''. The about:config "''This might void your warranty!''" warning page may appear.
    # Click '''I'll be careful, I promise!''', to continue to the about:config page.
    # Filter '''browser.download.useToolkitIT'''.
    # Double click and '''make sure it says true.'''
    # You now have the classic downloader back! Yay!
    Any issues or confused?
    * http://kb.mozillazine.org/About:config

  • Facetime between my Mac and MBPr not working

    I have 1 Apple ID account.  How do I facetime my iMac from my MBPr?  When I try it, it will say "Null" at the top of the Facetime screen.  Does this problem have to do with having 1 apple ID?  I tried separating my emails so one is associated with the mac and 1 with the MBP.  Any suggestions?

    http://www.apple.com/mac/facetime/
    http://support.apple.com/kb/ht4319

  • FireFox auto updated to 6.0 this weekend and has not worked properly since. I have uninstalled and reinstalled. Made sure all windows componets were up to date and still no joy. Any idea? Windows 7, 64 bit, normal configfuration. It is extreamly slow.

    FireFox auto updated to 6.0 this weekend and has not worked properly since. I have uninstalled and reinstalled. Made sure all windows componets were up to date and still no joy. Any idea? Windows 7, 64 bit, normal configfuration. It is extreamly slow and never finishes loading ANY page.

    I have had a similar problem with my system. I just recently (within a week of this post) built a brand new desktop. I installed Windows 7 64-bit Home and had a clean install, no problems. Using IE downloaded an anti-virus program, and then, because it was the latest version, downloaded and installed Firefox 4.0. As I began to search the internet for other programs to install after about maybe 10-15 minutes my computer crashes. Blank screen (yet monitor was still receiving a signal from computer) and completely frozen (couldn't even change the caps and num lock on keyboard). I thought I perhaps forgot to reboot after an update so I did a manual reboot and it started up fine.
    When ever I got on the internet (still using firefox) it would crash after anywhere between 5-15 minutes. Since I've had good experience with FF in the past I thought it must be either the drivers or a hardware problem. So in-between crashes I updated all the drivers. Still had the same problem. Took the computer to a friend who knows more about computers than I do, made sure all the drivers were updated, same problem. We thought that it might be a hardware problem (bad video card, chipset, overheating issues, etc.), but after my friend played around with my computer for a day he found that when he didn't start FF at all it worked fine, even after watching a movie, or going through a playlist on Youtube.
    At the time of this posting I'm going to try to uninstall FF 4.0 and download and install FF 3.6.16 which is currently on my laptop and works like a dream. Hopefully that will do the trick, because I love using FF and would hate to have to switch to another browser. Hopefully Mozilla will work out the kinks with FF 4 so I can continue to use it.
    I apologize for the lengthy post. Any feedback would be appreciated, but is not necessary. I will try and post back after I try FF 3.16.6.

  • Wireless network and bluetooth not working on touchsmart 600

    This has not worked since day 1 and I have been using wired internet.
    I really need to setup a home network and need to use wireless.
    Research on the net has led me to belive I should have HP WIRELESS ASSISTANT on my machine... is that correct?
    Everytime I try to download it is seem to be for a notepad... mine is a touchsmart desktop...
    Please advise  

    Hi coffee12345,
    Welcome to the HP Forums!
    I have read your post on your wireless keyboard and mouse not working with your desktop, and I would be happy to help you! To begin, I need to ask you a few introductory questions:
    What is the Product and Model Number of your desktop?
    What version of Windows are you using?
    Is this a recent issue, or has it been like this since day one?
    Are you using a USB hub to connect your peripherals or is it directly plugged into the computer?
    Please re-post with the necessary information, and I look forward to your reply!
    Regards
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • My Ipod touch 4th generation is not working, its frozen, ive tried everything and its not working, its just frozen on an app and i really really need HELP!!!

    My Ipod is frozen!!! Its a 4th generation and its frozen on an app, Ive tried everything like holding down the lock screen and stuff and its not showing the red thing to slid to shut it down....This is my only thing to use to contact my friends and its not working, i dont have a phone and i cant get one, so this is the onlything i have.....PLEASE HELP!!!

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • How can I get my itunes onto my new laptop? Do I need to download itunes again or can I just copy it? My ipod classic has since been soaked in water and does not work so I cannot copy from there. Can anyone help?

    How can I get my itunes onto my new laptop? Do I need to download itunes again or can I just copy it? My ipod classic has since been soaked in water and does not work so I cannot copy from there. Can anyone help?

    You should copy everything from your old comptuer to your new one.

  • Keyboard and Trackpad Not Working; Mac OSX Unexpectedly Quit?

    Hey everyone... I think I may need to stop by the Apple store to figure this one out, but I just wanted to make sure if there was anything I could do on my own first.
    So basically, on my MacBook Pro that I got nearly two years ago (late September of 2006) for the past month and a half has had problems. In the beginning, the mouse and keyboard would freeze up and just not work. Restarting the comp did nothing. Some times were worse than others (once it was frozen for 1.5 hours). Then it stopped, every now and then having a few freezes (sometimes when the keyboard froze but the trackpad was still good), but two days ago I had my comp not hooked up to an adapter. When the battery got low, the comp froze. I went to bed and closed the laptop, and the next day it was still frozen. I unfroze it, but then it happened again (I'm pretty sure the same situation... almost no battery)... and it is still frozen, even after multiple restarts.
    Also, during the time when freezes weren't as bad, sometimes the keyboard would get stuck on one key, usually the volume up button (very annoying)... then I was told to restart the comp. When I came back, I was told that Mac OS X had unexpectedly quit.
    Sorry that was a lot to read, but any help is really appreciated! Thanks!
    Not sure if this is also important, but I did spill some water on the keyboard a very long time ago (late December '06)... it wouldn't take this long for that to cause the problem, would it?

    Does booting up in [Safe Mode|http://support.apple.com/kb/HT1455?viewlocale=en_US] help at all? This boot mode checks the disk on startup and disables non-apple start up items and certain kernel extensions.
    Steve

Maybe you are looking for