Trunked connections to ACS appliance

We are replacing our Cisco ACS 4x server with a new ACS appliance. It is a Cisco UCS C220.
We went with the hardened Linux option for the underlying OS.
Our old server had multiple network adapters on different subnets so that it could authenticate devices on different VRFs (rings basically).
I see the new appliance has only 2 network adapters in it. Is it possible to configure these as a 802.1q trunk in order to have the device service requests on 4-5 subnets? I haven't seen documentation on how to do this.

Hi,
ACS v4.1.1.23 patch 5 is available so go for this new patch.
You should have a pc which can access ACS through web interface. Keep the patch file on the PC.
Follow the steps below on the PC:
[1] Extract zipped file
[2] Look for ?autorun.exe? file and double click on it
[3] It will start a tomcat server on your desktop and you?ll see a web page asking for ACS
SE ip address :
Provide in the ACS SE ip address and press ?Install?
[4] It will prompt for ACS admin username and password as shown below :
Provide in the username and password and login.
[5] Then it bring up ACS GUI, then go to
System Configuration > Appliance Upgrade Status > Download,
Then we?ll get a screen where it will ask for ip address of Install Server :
Provide in ip address of system from where we are applying this patch, in our case our
desktop ip address, then click connect.
[6] It will show us following screen :
Click on ?Download Now?
Then it?ll show us this screen :
Press ?Refresh? Till we see following screen :
[7] Now press ?Apply Upgrade?. Then it?ll ask for confirmation :
Press ?Upgrade?, then we?ll get information regarding the patch.
Click ?Yes?.
It?ll take few minutes to apply that patch on appliance.
Then it?ll show us a confirmation message :
Press ?Done?, then system will reboot.
To confirm that patch has been applied successfully, goto
System Configuration > Appliance Upgrade Status
After everything is fine stop the tomcat server by clicking on ?stop distribution server? or
if you want to apply this patch on some more appliance click on ?Install Next?
Hope this helps.
~Rohit

Similar Messages

  • No access to serial console in ACS appliance 111

    We have 2 Cisco ACS appliances running version ...
    Cisco Secure ACS 3.2.2.5
    Appliance Management Software 3.2.2.5
    Appliance Base Image 3.2.2.1
    The fact is that after initial setup, we have never used the console mainly because in a production environment we manage them through the Web Admin application. Now we have decided to upgrade both appliances to the latest version (3.3.3) and when we tried to connect to the serial console (115200,N,8,1, no flow control) we don't get any response from none of both ACS. It's quiet strange but we have found no way to make them work. We have tried several things I expose to you in case you can give us any hint:
    1. We have rebooted the appliance and we can see through the console all the start-up process but when it finally finishes the start-up, we see no login prompt.
    2. We have also shutdown the appliance properly and power it off and on again. Same results. The appliances boot normal but still we don't have console access.
    3. We have tried boot the appliance with the recovery CD-ROM and the console works fine. I can reset the Admin password, but when it restart from its own system ( I mean without the recovery CD_ROM), I can see all the starting messages but when it finish the start-up process ... no console access.
    4. Finally I have connected a monitor and a keyboard to the appliance ( I know Cisco dosn not recommned it but when in trouble....) and I see the full start-up process and it includes the base Windows 2000 server operating system startup. When Windows finishes loading, we get a lock screen in which the appliance informs you that it have started correctly and that we could access it for management through the serial console port or through the web console. 10 seconds later I see a pop up window stating that on or more services have not started correctly and that we shoulkd check the Event viewer, something we wished we could do but as you you, this is a secured system and I don't know if there is a back door method to verify windows services in this appliance.
    Any help would be appreciated, as the problem is identical in both the appliances and upgrading them without access to the admin console is difficult and risky.
    Kind regards.

    Hi
    I had similair problem being locked out of console after initial configuration wizard.
    I think there is a bug within the console session in that if you input a hostname of more than 15 characters, it locks up the ACS service when the server reboots. If you keep your hostname to less than 15 characters, the server reboots and you get console access. If you then access the GUI, you will see that 15 characters is the maximum, and you cannot enetr any more than this. This is not the case with the console, where you can enter more than 15 without getting an error message.
    I rescued the server by doing F8 and rebooting server with last known good configuration. from there, you can reset the hostname to something valid. You can check to see which CS services are running through console session, and start any services that may not be running..
    deliverance1> start CSAgent
    Starting service: CSAgent..
    CSAgent is starting
    CSAgent is running
    Regards
    Ian

  • Apply patch to acs Appliance

    I was wondering if someone can help me to upgrade my ACS Appliance with patch 4.1.1.23.4-SW. It was simple to apply this one in a normal server 2000. The ACS appliance I think is different because that we can access by normal terminal, keyboard and mouse.
    Some were I read that is necessary a tomcat server?
    Please help
    adi

    Hi,
    ACS v4.1.1.23 patch 5 is available so go for this new patch.
    You should have a pc which can access ACS through web interface. Keep the patch file on the PC.
    Follow the steps below on the PC:
    [1] Extract zipped file
    [2] Look for ?autorun.exe? file and double click on it
    [3] It will start a tomcat server on your desktop and you?ll see a web page asking for ACS
    SE ip address :
    Provide in the ACS SE ip address and press ?Install?
    [4] It will prompt for ACS admin username and password as shown below :
    Provide in the username and password and login.
    [5] Then it bring up ACS GUI, then go to
    System Configuration > Appliance Upgrade Status > Download,
    Then we?ll get a screen where it will ask for ip address of Install Server :
    Provide in ip address of system from where we are applying this patch, in our case our
    desktop ip address, then click connect.
    [6] It will show us following screen :
    Click on ?Download Now?
    Then it?ll show us this screen :
    Press ?Refresh? Till we see following screen :
    [7] Now press ?Apply Upgrade?. Then it?ll ask for confirmation :
    Press ?Upgrade?, then we?ll get information regarding the patch.
    Click ?Yes?.
    It?ll take few minutes to apply that patch on appliance.
    Then it?ll show us a confirmation message :
    Press ?Done?, then system will reboot.
    To confirm that patch has been applied successfully, goto
    System Configuration > Appliance Upgrade Status
    After everything is fine stop the tomcat server by clicking on ?stop distribution server? or
    if you want to apply this patch on some more appliance click on ?Install Next?
    Hope this helps.
    ~Rohit

  • ACS Appliance configuration issue.

    When I attempt to configure the ACS IP address I am getting the following error:
    "Error; Failed to get NIC configuration: <null> <FFFFFFFF>"
    The device is connected to a working ethernet port and the the physical layers have been eliminated. Aside from starting from scratch, can anyone suggest a way out of this problem?

    you need to reimage the ACS appliance.

  • ACS Appliance Upgrade

    I obtained the 3.3 release from Cisco. I'm currently running v3.2. When I go to System Configuration -> Appliance Upgrade Status -> Download -> Connect -> Download Now, it returns "No Distribution in Appliance". I can see the 3.3.3.11 in the software install table. but it returns the error above when trying to transfer the file. I'm running Apache / Windows XP SP2. Anyone seen this before?

    Hi,
    Without Distribution server, normally you need to load the new image into the current ACS appliance itself before execute the upgrade process. The new image can be transferred via serial or ACS web-based 'system upgrade' option.
    If I am not mistaken, the error you're getting was due to unavailability of distribution server.
    If you stuck with the image transfer, try to use CLI/console mode.
    Typicall upgrade method has 3 steps:
    1. Load new image (download from Cisco or using CD) onto a distribution server.
    2. Load the upgrade image onto the Cisco Secure ACS Appliance from the distribution server. Do it either from within the HTML interface, or from the serial console. The Cisco Secure ACS Appliance will verify the transferred files to ensure that they have not been corrupted.
    3. Apply the Cisco Secure ACS Appliance system upgrade. You can do this either from within the HTML interface, or from the serial console.
    Refer to the following url for complete upgrade processes & options:
    http://www.cisco.com/en/US/partner/products/sw/secursw/ps5338/products_installation_guide_chapter09186a0080203004.html#wp1044616
    Rgds,
    AK

  • ACS Appliance Hardware functionality

    Just received a new ACS Appliance and in testing out the functionality I've encountered a couple of curious issues...
    Shutdown -- Have tried doing shutdown from both HTTP and Serial connections. Command is accepted and the hard drive light flashes for a bit and then nothing. It does not power off, don't get a message on the serial console saying it is OK to power off. Waited 20 minutes then used the power button. Seems to conflict with the doco.
    Can we/How do we use the second Ethernet port? Don't see anything about how to configure it in the doco but when I plug a cable in I do get lights indicating it is active.
    I have been able to complete basic configuration and do have connectivity and authentication against Internal User, still fiddling with getting communication with our LDAP User database, So the unit does function.

    For the 2nd ethernet connection, the doco here (http://www.cisco.com/univercd/cc/td/doc/product/access/acs_soft/csacsapp/csapp33/install/ovrvuap.htm#wp1040777) gives the answer:
    Ethernet Connectors
    Your system has two integrated 10/100/1000-megabit-per-second (Mbps) Ethernet connectors. Cisco Secure ACS Solution Engine supports the operation of either Ethernet connector, but not both connectors. Each Ethernet connector provides all the functions of a network expansion card and supports the 10BASE-T, 100BASE-TX, and 1000BASE-TX Ethernet standards.
    Each NIC is configured to automatically detect the speed and duplex mode of the network.
    Note The Cisco Secure ACS Solution Engine supports the operation of only one Ethernet connector at a time. Concurrent operation of both Ethernet connectors is not supported.
    For the shutdown issue, not sure, haven't seen that before.

  • Syslog on ACS Appliance

    is it possible to configure syslog on ACS appliance running ver 3.3?

    Please take a look at extraxi csvsync. Its our http(s) client that can download logs from ACS v2 or later (software or appliance).
    You simply create an Administrator account on the ACS with access rights to the "reports & activity" page plus each log types you want to download. On a PC somewhere you can schedule csvsync to connect and download all new logs (csvsync keeps a history of what its previously downloaded) over http.
    By doing a once (perhaps twice) a day bulk download you reduce the inefficient "drip drip" of syslog traffic that can be a problem over WAN. Also, you're guarunteed to get the log data - remember syslog is a non-acknowledged "fire and forget" protocol... ACS can be firing but the other end might be forgetting!
    csvsync also supports filename postfixing - so you dont get name clashes when downloading from multiple ACS servers.
    Used on its own csvsync is a great way to bulk archive the valuable ACS log data, however used in conjunction with extraxi aaa-reports! and you have a full log collection and reporting application.
    For more on csvsync or aaa-reports! please visit http://www.extraxi.com - free 60 day eval versions available.

  • ACS Appliance 3.3 Integration with Envision

    How to install the ftp agent on the ACS appliance 3.3 to integrate it with the envision for centralized logging.

    To the best of my knowledge you cannot install anything on the appliance. period.
    So any solution requiring agents doesnt work.
    You might want to look at our CSVSync utility (part of the aaa-reports! product family) that connects to ANY type of ACS Server via its HTTP interface.
    http://www.extraxi.com
    Darran

  • ACS appliance setup help

    Network environment:
    - Windows 2003 with enterprise CA
    - Cisco ACS appliance 4.1.1.23
    - Cisco 1240 AG series APs
    Wireless clients:
    - Windows XP SP2
    Brief steps taken:
    - Installed Enterprise CA
    - Created copy of web server certificate with option “Mark keys as exportable” enabled. Certificate published.
    - Created global group in AD that contains test user and a single laptop that is a member of domain - for auto enrolment.
    - Generated certificate request from ACS (1024 key length).
    - Submitted server request from ftp server - Submit a certificate request using base 64…
    - Submitted CA certificate request from ftp server - Retrieve CA certificate or revocation list /base 64 encoded.
    - CA & server certificates installed in to ACS appliance (Domain certificate authority approved within ACS)
    Brief cofig of ACS appliance
    Global config
    - PEAP -Selected “Allow EAP-MSCHAPv2”.
    - LEAP - Allow LEAP (For Aironet only)
    - Selected “Allow MS-CHAP Version 1 & 2 authentication
    - Added AAA client (AP) with shared secret with authentication using “Radius (Cisco Aironet)
    - Under External user DB//DB config/windows database, “Enable PEAP machine authentication” selected.
    1240 series AP config
    - Under Server Manager, ACS IP with shared secret entered as a Radius server.
    - Selected EAP authentication.
    - Under SSID Manager selected open Authentication with EAP & selected network EAP.
    - Under Encryption Manager selected WEP Encryption & mandatory.
    - Selected key 1 and entered 128 bit key
    Client (windows XP SP2 domain member) config
    - Connected to Enterprise CA web site, base64 encoding/download CA certificate
    and installed it in local computer store.
    - Under Network authentication selected open with WEP EAP type “protected EAP (PEAP)
    - Authenticate as a computer selected
    - Selected my CA under “Trusted Certification Authorities
    - Authentication method (EAP-MSCHAP V2)
    Errors:
    Automatic certificate enrollment to local system failed to contact the AD. The specified domain does not exist or cannot be contacted.
    Or
    Computer doesn't have correct certificate
    Used 43486, 64067, 71929
    Any suggestions very much apretiated.

    ACS Agent is installed on two DC's as well and they are detected by ACS.
    Thanks

  • ACS Appliance Backup

    I am trying to backup my ACS appliance. I am able to connect to my ftp server, Im using Filezilla on my laptop, but it fails to connect to the folder.  In the appliance, under the Backup Setup, Directory - I have used c:/backup and /backup, and it fails to both.

    Hi,
    It will back up your certificates as well.
    The link below gives the details of the components backed up.
    http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/SCBasic.html#wp289217
    Regards,
    Anisha
    P.S.: please rate the post if you find it has answered the query.

  • Old ACS appliance access

    Hello everybody,
    I have an ACS appliance 1111 installed on HP server. It's installed and I have to CD to make a recovery.
    The server starts until arrive at the page where say that ACS i running and you can access via Serial or Browser.
    I havn't the IP address to access and the Serial with standard parameters didn't show anything.
    Please, anyone can help me how I access to manage this ACS ? I worked on it only on software version

    Without assigning the ip address it is not possible to Login into the ACS from remote.
    To log on to the Cisco Secure ACS Appliance via a serial console, follow these steps:
    Step 1 Establish a serial console connection to the Cisco Secure ACS Appliance. For details, see Establishing a Serial Console Connection.
    Step 2 At the login: prompt, enter the Cisco Secure ACS Appliance administrator name.
    Step 3 At the password: prompt, enter the Cisco Secure ACS Appliance password.
    Result: The system prompt appears in the following form:
    Cisco Secure ACS Appliance name

  • Adding a Custom VSA to a Group - ACS Appliance

    Hi,
    Using a secure ACS Appliance 4.0
    I want to add a new RADIUS Vendor and its associated VSA to the ACS configuration. This will then be returned during Authorization.
    I have already added the new Vendor and the required VSA through RDBMS. I can now see the new vendor as RADIUS (vendor) in NAP Profile etc
    However I cannot seem to find a way that how would i set the Value of the Added VSA ? And assign it to a particular group ? I cannot seem to find that VSA anywhere.

    Add a AAA client with "Authenticate using" Radius(vendor)
    then go to Interface Configuration and enable VSA for Group/User
    ~Rohit

  • ACS appliance External Auth to NT 4.0

    Hi
    I am installing the ACS appliance to do external database authentication to NT 4.0 PDC. It appears with the appliance you have to install a remote agent to make this work. It is my understanding this agent must run on a win2k box. Does the agent have to be installed on the PDC or can it go on any windows server box?
    Is there a work around if you do not have a win2k server. This network is still NT4 with now win2k boxes
    Thanks

    The remote agent was not tested on NT4 and probably wouldn't even install properly. Even if it did work, you would be very limited in the support you'd get if you had strange problems because it is an unsupported configuration.
    It doesn't have to go on a PDC, but things just seem to work better if it is on a DC of some sort. At the very least it needs to be on a member server, but as I said, I'd recommend putting it on a BDC from experience.
    The release notes/install guide for it is here:
    http://www.cisco.com/univercd/cc/td/doc/product/access/acs_soft/csacsapp/raig/index.htm

  • New ACS appliance not showing FQDN hostname in GUI

    I've installed two new ACS appliances in our environment running 5.3.  I've just configured the basics to get it on the network (ie DNS, default GW, IP address).  Looking at both running configs, they are identical with exception to the IP addresses.  On one appliance in the GUI next to the user name in the top right hand corner, the hostname is "acs01".  In the GUI on the other appliance, it shows "acs02.corp.mycompany.com".  This is a minor issue but its bugging me.  Anyone have an idea what is going on?
    In both appliances, this statement is identical in the show run:
    ip domain-name corp.mycompany.com

    Hi,
    So you are using a hardware RAID5 in storage pool as a hard disk. Now you added one more hard disk to the RAID5 with the tool "Dell Server Administrator" but it is not recognized in storage pool.
    I think it will not work as hard disk size cannot be changed after storage pool is created. It is by default.
    However why you use the hardware RAID in a storage pool? A hardware RAID seems enough for your storage requirement.
    If you have any feedback on our support, please send to [email protected]

  • RDBMS Synchronization problem in ACS Appliance 3.3

    Hi,
    I was adding multiple AAA Clients on ACS Appliance using RDBMS Synchronization option I followed the complete steps but failed to synchronize accountActions.csv file on ACS my ftp server is working fine and returned the logs saying "accountActions.csv file read recieved file successfully size 0 bytes 0.00 kbps" and RDBMS synchronization logs ACS reported as "No import CSV file on ftp server - nothing to process" I have attached related screen shots. Any help on this issue will be highly appreciated.
    Thanks in advance
    Best Regards,
    Ahmed

    The format of the accountsaction.csv file is incorrect as a result of which the RDBMS Synchronization is not executed correctly.
    I have attached a sample accountsAction.csv file for you.
    (i) The AAA Client C7609-X with the ip address 10.10.10.10 has been added with the shared secret key as mikey and is is registered with TACACS+
    (ii) The NDG michasisX has been added.
    (iii) The device C7609-X has been added to the NDG michasisX
    Place the file in the FTP and try performing an RDBMS synchronization. Restart the ACS services.
    Then you can add the devices as per the sample file attached.
    Also check if the file name is exactly the same in the RDBMS Synchronization page in the ACS
    Hope this helps,
    Soumya

Maybe you are looking for