Trunking on a T2000 using the internal ipge interfaces.

We have a new T2000 with solaris 10 + sun trunking for solaris 10 installed.
Has anyone been able to setup trunking on a T2000 using the internal ipge interfaces
The T2000 has four of these interfaces and would be nice to run trunking over a pair for performance / redundancy reasons.
I did first look at link aggregation in solaris 10 but the ipge interface is recognised as a legacy device not supported by link aggregation.
Thanks for any help

From: http://www.sun.com/servers/coolthreads/tnb/parameters.jsp
Improving Network Performance by Transitioning from ipge to e1000g Network Drivers
Transitioning to the e1000g network driver provides significant enhancements to network performance as a result of:
* better handling of small network packet sizes
* lower processor utilization
* network port link aggregation (trunking)
To transition to the e1000g driver, please follow the steps below:
* Install patch 118833-24 or later
* Convert from ipge to e1000g by installing patch 123334-02 and running the script provided
* Update the /etc/system file so that is contains only the following command:
set pcie:pcie_aer_ce_mask=0x1
* reboot your system
No tuning is needed for e1000g

Similar Messages

When I try to use the internal hard drive as a scratch disk I get this error "unable to set scratch disk- the selected directory is on write protect or non-writable media. Any ideas on how to fix this. It only happens in fcp.

When I try to use the internal hard drive as a scratch disk I get this error "unable to set scratch disk- the selected directory is on write protect or non-writable media. Any ideas on how to fix this. It only happens in fcp.

By internal, I assume you're referring to your systems (boot) drive. Is it, by chance, a partitioned dive?
Also…although many people successfully use their systems drives as scratch disks, over time you'll have better results using a dedicated drive for your media.
Good luck.
Russ

Using the internal drive on a Macbook Pro or not?

I am having one external esata disk and two seperate FW800 disk. Where should i put my scratch files? On the internal disk? Should I avoid using the internal disk for a video stream and leave it to accessing the system and Final Cut Pro (6.06) only or can it come into other use as well?
The setup is a MBPro 2.4 Ghz with 4GB of ram.

On my 17" MacBook Pro I use the eSata port for Black X Duet Hard Drive Docking station where I put 2 1TB Hitachi internal drives. They are swappable and are about $80.00US. I use the USB port for my system backup and a G-force 500 MB bus powered portable drive on the FW800 port just for the heck of it. It works out really well for me.

Digital audio input via mini jack/toslink from ADA, monitored via USB audio output... is this do-able? I know digital audio input should be okay but how do I monitor it, apart from using the internal speakers?

Digital audio input via mini jack/toslink from ADA converter, monitored via USB audio output to amplifier... is this do-able? I know digital audio input should be okay but how do I monitor it, apart from using the internal speakers?

You can output audio thru HDMI, with appropriate adapter.
You can use additional cheap external usb audio for monitoring.

The last few times I've used headphones in my iPad, the audio has been all messed up to the extent where it's better to just use the internal speakers and not the headphones. I've tried multiple pairs of headphones to no avail. Help?

The last few times I've used headphones in my iPad, the audio has been all messed up to the extent where it's better to just use the internal speakers and not the headphones. I've tried multiple pairs of headphones to no avail.
The iPad was bought in mid-June, but I did not get extended Apple-Care warranty on it. Any idea of what's happenening?

Multiple means how many? If only 2 or 3, they could all be faulty. Try the headphones in some other device, to make sure they are OK. Or there could be something wrong with the headphone port.
Your iPad is still covered by the 1-year warranty so you should make a Genius appointment and have it looked at.
Another thing to try is to plug in the headphone jack a few times in succession to see if it frees up something inside the port.

Using The Internal Audio

Hello,
I've been experiencing problems with a third party audio interface, namely Mbox, working smoothly with Logic. It was suggested to me that I should try using the internal audio for working with Logic. I was laboring under the false assumption that the internal sound was only 16bit. I would like some feedback from someone who uses the internal audio in a home studio situation. Namely 1. If possible, how to connect the internal output to an external monitor system. 2. How to connect a preamp for recording through the internal sound. Can this even be done and can I expect results equal to the Mbox?
Thanks

Actually, it doesn't make a difference if it's a TRS or an XLR. The difference is in the Apogee's inputs. With the One, you have either a instrument quarter-inch input or a Mic XLR input. Neither works with a balanced +4 line signal, which is the signal coming from the Grace. With the Duet, you can switch internally the XLR inputs from Mic to +4db line signal.
Also, I know the Grace preamp is really good but another possibility is to stop using it and plugging your mic directly into the Apogee preamp. I know it can sound weird as a suggestion but you'd be surprised at how good the Apogee pres are. And if you only need one preamp, the One will work for you. One last thing: the Duet is Firewire, the One is USB. That means you should be able to have lower buffer settings with the Duet, hence less lantency.

Can I use the internal airport card of my Mac as a BRIDGE?

* My Mac is part of my home network.
* My wired Router provides NAT addressing for all wired computers and printers.
Question:
Can I use the internal airport card of my Mac as a BRIDGE?
I am able to create a second LAN where the internal airport card, creates it's own network, but then the wireless computers are not on the same network as the wired.
If using an Airport Express, there is an option you can uncheck "assign IP address" that turns it into a bridge.... Is there anything similar with os X 10.4.3

answered in another thread

Configuring the 3750G WLC to use the Internal DHCP Server

I want to use the Internal DHCP Server on a 3750G WLC to hand out IP's to gueat users. I'm having issues getting the DHCP server to hand out addresses for the guest network - any suggestions would be a great help.
Configuration Details are attached.

Configuring DHCP
http://www.cisco.com/en/US/docs/wireless/controller/5.2/configuration/guide/c52wlan.html#wp1293808

HT4628 I can not use the internal wireless card with my Mac pro 2012, I don't know if it is broken

I can not use the internal wireless card with my Mac pro 2012, I don't know if it is broken. The problem is happen recently, I have to use an independent wireless card now. Thanks!

When you enable Internet Sharing in OS X, you are creating a separate sub-net.
There is no option to allow this to be a simple pass-through from Ethernet to AirPort (or the other way).
The problem is easily solved by getting an inexpensive wireless router. You can replace your current router OR disable the DHCP server on the wireless router and allow the wireless clients to get an IP address from the current router.

Nasty feedback when trying to record using the internal mic

I get nasty feedback when trying to record using the internal mic on my macbook. I'm running Maverick. Why is this happening?

Note: there may be other issues involved, but without further details I can only suggest that using headphones is the best way to accurately hear what you're recording, adjust gain levels, and avoid feedback. So this should be the first thing to try as you troubleshoot.

After using the internal mic for the first time I am getting a buzzing feedback from my audio output

After using the internal mic for the first time I am getting a buzzing feedback from my audio output

Go to System Preferences Sound Input and adjust the volume level down by dragging the slider to the left. With an audio app like Logic there is an option for input monitoring when recording so there might be a feedback loop if the volume is set too high. Garage Band works in a similar way. Always be careful when using headphones as the noise can be frightful and cause hearing damage.

Using the internal camera in a 3G mobile phone.

It's possible to use the internal camera in a 3G mobile telephone or only the external?
thank you.

Hi,
i have an application that use the "external camera" (i don't know the exactly name) but i don't know how could i especify to the player that i want to use the "internal" camera (the camera what focus the face in 3g phones).
I supose that the url (capture://video) should be different in the below code.
mPlayer = Manager.createPlayer("capture://video");
Thanks for all,
Benji.

My macbook air doesn't let me use the internal microphone

My macbook air doesn't let me use the internal microphone while my headphones are plugged in. The reason I want to use the internal mic is that the person I talk to can hear me louder if I used the internal mic. Can someone help please ASAP? Thanks.

I assume you're using the 3 slot mini jack of the Apple earbuds/ mic. Use a 2 slot headphone jack that doesn't make contact with the the microphone contact in the headset jack on the AIr.
The Air has a HEADSET jack, in which either headphones or headsets can be used.
headset jack on left, for both MIC and headset...............headphone jack for earbuds/ speakers on right (listening only)

HT1948 Does the macbook use the internal harddrive when booting from usb and when fully booted?

I wonder if the Macbook Air uses the internal SSD drive when booting Mac OSX lion 10.8.2 from a bootable USB stick?
I am suspecting the internal harddrive is faulty because it gives me random system freeze ups during normal use, making me hold the power button to shut it down. So I'm wondering if I boot my macbook from a bootable USB, if the internal drive is used for caching or anything?

What i'm doing when it freezes is totally random. I am not having any programs open, but for example just clicking on the apple icon or starting up safari, there seems to be no specific program that crashes it. I'm still running without a freeze up after I fixed the drive permissions with Disk Utility. But here is Etrecheck;
Hardware Information:
MacBook Air - model: MacBookAir2,1
1 1.86 GHz Intel Core 2 Duo CPU: 2 cores
2 GB RAM
System Software:
OS X 10.8.2 (12C60) - Uptime: 0 days 0:9
Disk Information:
APPLE SSD SM128 disk0 : (121,33 GB)
disk0s1 (disk0s1) <not mounted>: 209,7 MB
MacBook Air (disk0s2) /: 120,47 GB (106,36 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
USB Information:
Apple Inc. Built-in iSight
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
FireWire Information:
Kernel Extensions:
Problem System Launch Daemons:
Problem System Launch Agents:
       [failed] com.apple.afpstat.plist
       [failed] com.apple.mrt.uiagent.plist
Launch Daemons:
   [not loaded] com.bjango.istatmenusdaemon.plist
Launch Agents:
       [loaded] com.bjango.istatmenusagent.plist
User Launch Agents:
User Login Items:
iTunesHelper
3rd Party Preference Panes:
None
Internet Plug-ins:
JavaAppletPlugin.plugin
QuickTime Plugin.plugin
User Internet Plug-ins:
Bad Fonts:
None
Top Processes:

How can I use the color adjustments interface that shows up for camera RAW on jpeg files?

How can I use the color adjustments interface that shows up for camera raw on other files types? The HLS controls had the secondary color adjustments (6 colors instead of the 3). Plus, it had same vibrancy and a better Curves interface. Yesterday was the first time I imported raw into Photoshop CS5 and I got that really cool interface. What is that? Can I use that on other file formats?

Actually I am using the Tradional Chinese Version, when I try to edit the jpg file with camera raw, the system shows that there is no camera raw plug-in. The cmaera raw never work.

Trunking on a T2000 using the internal ipge interfaces.

Similar Messages

Maybe you are looking for