Trying to add a toshiba USB 3.0 drive to Airport Extreme---possible??

FIRST TIME TRYING TO ADD A HARD DRIVE TO MY AIRPORT EXTREME----PURCHASED A USB3.0 TOSHIBA.
CAN'T SEEM TO GET IT REGOGINISED WHEN PLUGGED INTO THE AIRPORT EXTEME
IS 3.0 THE PROBLEM???
ANY OTHER RECOMMENDATIONS
THANKS

In addition to Niel's comments, I assume that you understand that the USB3 speeds will drop to down to USB2 levels at the AirPort Extreme.
Actually, it will be worse than that, as the USB2 processor on the AirPort Extreme runs at about half the speed of a USB2 processor on a computer.
If you can get the drive formatted correctly, things are still going to be really SLOW.

Similar Messages

I am trying to add a toshiba commercial network printer to my air book , its no t working !

i am trying to add a toshiba commercial network printer to my air book , its no t working !

What format is the drive?

Can't add hard drive to Airport Extreme

I wanted to add an external hard drive to Airport Extreme and I can't get it to show up in my net work. If I go to the configuration program for Airport Extreme, I can see that the base station has identified that hard drive (a Lacie 750 mb drive). Any suggestions?
Message was edited by: Karlhan

I have the exact same problem with one twist I tried adding an 8gb memory stick instead of a spinning hard drive. Airport utility recognizes it but it does not show up on any of the computers.

File transfer speed in Shared USB Hard Drive via Airport Extreme

I' am planing to buy one of this, but first I need to know what kind of file transfer speed I can expect when sharing USB drive via Airport Extreme 1000Mbps Ethernet.
Thanks.
Message was edited by: Robert81

most likely 14m/sec but normally 10.5 this is ethernet wired and usb attached. wireless would be about 8M/sec
Wired is good enough I use it for Finder copy frequently.

Usb hard drive and AirPort Extreme

I have been using an external usb hard drive connected to my Airport Extreme to store music which is then picked up by a Sonos system to play music even when my iMac is switched off - has been working great. However I became aware recently (and I think this pre-dates upgrading my iMac to Mountain Lion) that my external hard drive no longer shows up as a shared drive within Finder. If I go into Airport Utility / Edit / Disks - 'enable file sharing' is checked. Disk Utility doesn't see the drive but I'm not sure that really means anything as a network drive rather than a drive connected directly to the iMac.
Has some recent upgrade disabled network drives on Airport Extreme's (ie assuming we are all now backing up to iCloud so don't need it)?
Thanks

OK, I feel silly on this one.
After looking for issues with the airport and not finding any and needing a file from my backup drive, I had to connect it up to my PC. That's when I found my solution.
The Drive I had connected had stopped responding. That's why the Airport was not showing it and not allowing connections. I had power cycled the drive a few times while testing, just not long enough. I unplugged the drive for 2 minutes, all cables, then reconnected. After about 5 minutes, the Airport was able to confirm the drive and turned the share back on.
Hope that helps.

Error when trying to add printer on USB Print Server

I'm attempting to connect to a Canon MP530 printer via a Netcomm NP3680 USB Print Server.
When attempting to add the printer via the Print & Scan process, the USB port is seen by the MacBook and listed - ie: mini_me-3-usb2, and the driver is selected automatically without any problem after gathering printer information, however the macbook is unable to connect and returns the error: "An error occurred while trying to add the selected printer."
If a manual configuration is attempted the message returned is: "An error occurred while trying to add the selected printer. Unable to communicate with the printer at this time." Further manual config via the IP address will allow the printer to be entered, however the printer is non-responsive.
I have setup this printer via the same Print Server on the same Macbook prior to this and it setup and worked correctly - the same setup is working correctly on my wife's macbook. However I had to remove the setup on my Macbook and can't get the printer functioning again on this particular Macbook, or my son's.
The direct connection setup via USB directly works without any problem at all.
I'm currently running OSX 10.8.1, however my son is running 10.7.x and has the same problem. My wife's macbook is also running 10.7.x and is working fine.
Can anyone throw any light on this issue - it is truely frustrating, especially when I know it has worked in the past.
thanks very much in advance
GDT

After 55 views and 0 replies, and a number of calls to Applecare (without success) , I decided to once again troubleshoot the problem.
Fixed!
Bearing in mind, I had no other printers already set up in the Print and Scan window....
I removed the following items from the /library/preferences directory:
"com.apple.print.makequeues.plist",
"jp.co.canon.ij.print.filter.raster2canonij.plist",
"jp.co.canon.ij.print.utility.command2canonij.plist",
"org.cups.printers.plist"
I also removed all items from the /library/printers directory (including Canon, PPDs, plist files and icons)
Then I retried to install the printer..... (holidng my breath) and the Console showed:
Repairing access permissions of "/Library/Printers/InstalledPrinters.plist"
All is fine now

Setting up shared usb drive on airport extreme

I just bought a new airport extreme a couple of weeks ago and setup a wireless network in my home. Now i was thinking of connecting a usb hard drive to the airport extreme to act as a place to backup and share files. Looking through the manual it looks like I have to recreate my network to make this happen or is there a way to just add the drive to an existing network?? Thanks.
David

Pretty much.
o Connecting a USB hard disk to your base station
o Sharing a USB hard disk on your network
o USB storage device supported formats and protocols

Incompatibility Issues with connecting USB Hard Drive to Airport Extreme

Over the last few days i have been fiddling around with my new Airport Extreme Base Station N router. I can connect a printer and use the internet through it seamlessly. I can even share two of my hard drives through a USB hub, however, my Maxtor 500 gb One Touch 4 HDD will not connect with my macbook through AEBS. It is only this drive that is not working with AEBS and it is the one i need to be connected and sharing. If i plug my 500gb Maxtor directly into my macbook it works fine, i can read all the files. This drive is formated as Mac OS Extended (journaled).
I am about to give up on this because i have tried everything:
1. Reformatted HDD
2. Downgraded Firmware
3. Searched Forums for advice
4. Reconfigured AEBS in, i think, every way possible
So, these are most of the things ive tried and so far there is no solution in sight. I have one hypothesis: my particular HDD (Maxtor 500gb One Touch 4) is incompatible with AEBS at this time, but it is possible that a future firmware update could fix this.
Does anyone have any advice? I'm lost and disappointed. Please help, thanks.
Message was edited by: benjaminwooda

Chances are pretty good that the power draw of your external drive is just at the "tipping point" for what the USB port on the Extreme can deliver. Powered USB hubs are inexpensive and should help in this situation.

USB flash drive and Airport Extreme

I got an Airport Extreme, and one of the reasons why is so that I can have a drive attached to the router so that I don't have to leave on a computer for file sharing or go in and boot up the computer when I needed some files. I am using a 16GB USB flash drive at the moment formatted with FAT32 (no mac in the house). I tried to backup some stuff on it, a bunch of smaller files in a folder totalling about 4.3 GB. The base station keeps rebooting itself in the middle of the transfer.
I saw some threads on here that are hinting that Airport Extreme doesn't work well with any type of external storage, whether an actual HDD or a flash drive. Those were somewhat dated. Is there a way to fix this? I'm using the latest firmware.

OK, I feel silly on this one.
After looking for issues with the airport and not finding any and needing a file from my backup drive, I had to connect it up to my PC. That's when I found my solution.
The Drive I had connected had stopped responding. That's why the Airport was not showing it and not allowing connections. I had power cycled the drive a few times while testing, just not long enough. I unplugged the drive for 2 minutes, all cables, then reconnected. After about 5 minutes, the Airport was able to confirm the drive and turned the share back on.
Hope that helps.

How can I access USB drive on AirPort Extreme with iPad

Good day. I recently purchased an AirPort Extreme, and am very pleased. I thought I would take advantage of the ability to store files and videos of my children on my USB drive on the router. Installation was flawless, however, i cannot access the USB drive with my IPad. I have seen several postings about this, am i correct in reading that this is not possible without a 3rd party app? If that is the case, could someone point me in the right direction?

Have you tried this? (And is the Airport new enough that you can call Apple?)
*Manually mounting Mac OS Extended (HFS+) volumes*
*From the Finder's Go menu choose Connect to Server.*
*Enter the AirPort Extreme Base Station's LAN IP address (by default 10.0.1.1).*
*Enter the username and password required to access the AirPort Disk(s).*
*Select the desired AirPort Disk(s) from the available Volumes.*
*Manually mounting FAT16/FAT32 volumes*
*From the Finder's Go menu choose Connect to Server.*
*Enter the AirPort Extreme Base Station's LAN IP address preceded by smb:// (for example, smb://10.0.1.1 )*
*Enter the username and password required to access the AirPort Disk(s). Leave the Workgroup field empty unless you have assigned one in AirPort Utility.*
*Select the desired AirPort Disk from the available CIFS (Common Internet File System) volumes*

Cant see External USB on network via Apple Airport Extreme (XP) - FIXED!!!

Hello,
I started this post many, many months ago that has now been archived
http://discussions.apple.com/thread.jspa?messageID=7796850#7796850
and finally I've solved the problem!!!
I tried everything to share my external USB HDD over my home network through my Apply Airport Extreme, but couldn't get it to work!!!
I have a mac and PC, with the PC being closest to the DSL modem so I installed the Airport utility on the PC to configure it.. that was my mistake!! ..I fixed the issue my installing the utility on my Mac and configuring it from there.. now it works great!! - I can Access my hdd from anwhere on the network - and as a bonus, I have managed to copy files direct from my mac to my shared files folder in windows!!
I hope this helps someone!!
Daz

"so you can't use ethernet or wireless to connect the printer?"
There is no Ethernet port on the HP printer, nor does it have a wireless card; it is not a "network ready" printer, just a USB printer. I connected the printer to the network via a USB cable from the printer to the Airport Extreme. All the systems on the network can see the printer, show it as the default printer, but they can't print to it. When I was using the Airport Express as a print server, the printer was connected to the Express via its USB port and the Express was connected to the Linksys router via an Ethernet cable. In this scenario, everything worked perfectly, I could print from my wireless and wired systems with no problems at all.
Your printer has wireless capablities so has an IP adress. Does a USB printer have an IP address? I don't think so, but if it does, please tell me how to find out what it is - maybe that is my problem; I didn't need this info when I was using the Express as a print server. (Maybe I just need to buy another Express and use it as a print server and forget about using the USB port on the Extreme...defeats the purpose of getting the Extreme in the first place, but at least I could stop wasting my time with all of this!)
Holly
Message was edited by: OakIris

HELP! Problem accessing usb hard drive on airport extreme

Hi all,
Hopefully someone can help me.
I have a Macbook Pro (2009). Recently put on Lion and have had no problems until now. Last night, the computer could not see the USB HD that is plugged into our Airport Extreme that it was using for the time machine backups. HOWEVER, our Macbook (white 2007) which is also running Lion has no problems accessing the HD! The Airport is working fine as we can still access email, the internet and my NAS drive (D-link 323).
So, I went into the Airport utility and clicked on the Drive section... the drive is shown on the airport and the settings are all set for sharing (etc. etc.)... but in finder I cannot access any of the drives on the airport... I just get a "Connection Failed" and then a pop-up saying that there was an error connecting to the airport, check the address and if the problem persists check with the admin.
This is what I have done so far....
1. Rebooted the airport (using Airport utility)... didn't work.
2. Turned off the USB HD and turned it back on.... didn't work.
3. Verified and fixed the permissions on the macbook pro... didn't work.
4. Turned everything off and then restarted everything again... didn't work.
5. Compared all the settings on our macbook for the Airport extreeme (using the airport utility) and the macbook pro... everything was identical nothing needed to be changed.
6. Tried to connect to our macbook using the macbook pro... came up with a "Connection Failed"... HOWEVER I was able to share the screen?!?!?!?!?
7. I pinged the airport... no problems pining...its only has problems connecting to the drives on the airport.
The airport is shown under the "shared" section of finder along with my NAS dirve (D-link 323) and the macbook... I can access the D-link with no issues but nothing else.
Please help... this is very frustrating and It dosnt make sence as to why it can see the drive but wont let me access it.
Thanks!

A little update... spoke to Apple Care... they said that this happens and then are aware that this happens, but had no answers how to fix.
Unfortunately not much help... anyone else have any information?
Please help!

Is there a difference between AirPrint and printing via usb printer plugged into an airport extreme?

My printer does not show up in the add a printer option on my iMac when plugged into the extreme. I have a HP officejet 5610 All-in-One. I want to be able to print wirelessly using my Airport Extreme. Thank you

Is there a difference between AirPrint and printing via usb printer plugged into an AirPort Exreme?
Big difference.
AirPrint for one will not work via USB, so you will not be able to print from an iOS device like an iPhone or iPad using this type of connection unless you look at additional software....that may or may not allow this option.
Assuming that you get the All-in-One setup using the USB port on the AirPort.......only printing is supported.
You will not be able to use any other advanced features like maintenance, scan, copy, fax, etc when the device is connected to the USB port on an AirPort.
If you plan to use the HP for other things, I would strongly recommend that you connect it to your computer.
My printer does not show up in the add a printer option on my iMac when plugged into the extreme.
This usually indicates that your printer model is not supported. Check with HP Support to see if they have any updated Macintosh drivers for the 5610 that you could download and install that might allow this.
HP Officejet 5610 All-in-One Printer Drivers - Hewlett Packard

Setting up USB External Drive to Airport Extreme Base Station

I've attached an External Hard Drive to my AEBS. My base computer is connected to the AEBS via Ethernet Cable and can see the external drive under Networked Drive however it shows up twice as Drive Y and Drive Z both showing the exact same capacity.
My desktop computer is running windows vista, and my laptop is also running vista. My Laptop connects to the AEBS wirelessly. The laptop does not see this External Hard Drive. How do I get my laptop to recognize this drive? Shoule my external hard drive display with two different drive letters, or should it only appear as one? I've not had much luck using this feature of the airport extreme and was the basic reason i purchased the AEBS

The USB port on the AirPort Extreme will support drive formats of Mac OS Extended (Journaled) and FAT32. NTFS is not supported, so that might explain some of your difficulties.
What feature did I invoke that automatically established a "third" drive? Where is it established on the physically formatted Mac drive? Does the format of Appleshare just indicate how the partition is accessed?
Not sure about this. When I format a drive as Mac OS or FAT 32, I see a single drive when accessed from the Finder.

Setup of USB Hard Drive on Airport Extreme for Time Machine

Hi all,
I upgraded to Mountain Lion a while back and am running the latest Airport Utility. Here's the problem: I can't get Time Machine to work anymore with my USB Hard Drive attached to my Airport Extreme. Is this setup no longer possible under Mountain Lion? Do I have to buy a Time Capsule? For the last couple of years I've had two MacBooks backing up with no problem to the USB drive connected to the Airport Extreme. Any advice would be appreciated!
Thanks,
Chris

While you can do this as Kappy points out, there a few details that you might want to consider before you make the move.
1) Time Machine backups to a drive at the USB port of the AirPort Extreme are not supported by Apple. While this does seem to work for some users, others (like me) have difficulty with corruption issues. The bottom line is that this is not a reliable method to back up your important data....and, no support or help from Apple if you do have difficulties.
Reference this Apple Support Document to confirm:
"Time Machine can’t back up to an external disk connected to an AirPort Extreme......"
http://docs.info.apple.com/article.html?path=Mac/10.6/en/15139.html
2) If you move the iPhoto library to the hard drive attached to the AirPort Extreme....your original or master library now resides on that disk.....and you have no backup for the library.....when, not if.....the drive has a problem.
3) You might want to post in the iPhoto forum to ask if it is still an iPhoto requirement that only one user at a time can have iPhoto open with the shared library arrangement.

Trying to add a toshiba USB 3.0 drive to Airport Extreme---possible??

Similar Messages

Maybe you are looking for