Trying to connect airport extreme to comcast provided ubee modem. Light on airport green, but no internet access.

Attempting to connect ubee d3.0 comcast modem to airport extreme base station.
Light on airport will go green, but I cannot connect to the internet.
I'm sure it has something to do with DHCP/NAT - as the airport extreme is getting an IP address, but then assiging a 10.x.x.x IP to my computer
but attempts at putting it in bridge mode just causes the light to go yellow and give warning of "No DNS Server" and "No internet connection"
I am able to connect to the internet when I connected directly to the modem.
I'm running OS 10.8.5
previously had DSL modem and connected after a few easy tweaks of the NAT settings before. am unsure what the issue is on this on... have used up my rather limited tech knowledge.
any thoughts?
Thank you!

Attempting to connect ubee d3.0 comcast modem to airport extreme base station.
Light on airport will go green, but I cannot connect to the internet.
Ubee provides both cable modems and gateway devices. What is the model number of yours?
I'm sure it has something to do with DHCP/NAT - as the airport extreme is getting an IP address, but then assiging a 10.x.x.x IP to my computer
By default, the AirPort Extreme would performing as a router with both NAT & DHCP enabled. Also, it would act as a DHCP server for the local network and provide out Private IP addresses in the range of 10.0.1.2 - 10.1.1.200. The WAN-side IP address of the Extreme should be a Public one and provided to you by your ISP via the Ubee modem. Did you perform a "factory default" reset on the Extreme before attempting to connect it to the modem?

Similar Messages

  • Able to connect ipad 2 to iphone 4s personal hotspot via bluetooth or wifi, but no internet access when connected via wifi.

    I am able to connect my ipad 2 to an iphone 4s personal hotspot via bluetooth or wifi.  The problem is that I only have internet access with a bluetooth connection. Both are running ios 6.1.2 and I have tried to reset both to factory settings. Any suggestions would be reatly appreciated. 

    Please don't shout!   Using all uppercase means shouting on the internet.  If your keyboard is stuck please say so, otherwise people will think you are being obnoxious.
    Now the first question is, when you are saying connecting to personal hotspot, have you always been using the iPhone to connect to the internet?   Are you someplace where the only place to connect is available via tethering to the iPhone's celluar network?  Or do you have other options?

  • Just bought new AirPort Extreme did everything on manual and light still flashing amber , it is connected to an Arris TM822 from optimum cable company , help please

    Just bought new AirPort Extreme did everything on manual and light still flashing amber , it is connected to an Arris TM822 from optimum cable company , help please

    Any luck with the suggestions mentioned by Bob Timmons?
    I am having pretty much the same issue.
    Got a new modem Arris SB6141 and a new Airport Extreme ME918LL/A. Activated with my ISP (Comcast). Worked with a savy tech who knew the modem and Airport Extreme. Ensured all items were correct from the ISP side.
    I follow the instructions as indicated for Airport Extreme by it fails to detect the internet and dns servers. Comcast suggested I call apple. Reading posts above I will:
    -Reset the airport extreme
    -Unplug the modem for 30min
    Airport Utility 6.3.4 (634.17)
    Airport Extreme ME918LL/A Firmware Version 7.7.3
    MBP - Yosemite Mid 2012
    Appreciate the assistance folks.

  • Airport extreme and Comcast

    I can't seem to get my (new) airport extreme to work. I have internet access (via Comcast) when I go directly from the router to my Mac. When I plug it into the airport extreme unit, I get the green light, but my Mac can't seem to find the signal. Any ideas?

    That Comcast modem needs to be completely reset to be able to issue an IP address to the AirPort Extreme.
    Power off the modem completely by pulling the power cable from the back of the device or from the wall AC socket. Pull the battery as well if it is easily accessible.
    Let the modem rest for 30 minutes
    Power off the AirPort Extreme as well and leave it off
    After the power down period, reinstall the battery if it was pulled, start the modem first and let it run for 5 minutes by itself
    Then, start the AirPort Extreme the same way
    Check the network and report on your results.

  • Airport extreme wont work with dhcp modem

    Hello,
    my airport extreme quits to work with my adsl modem after several hours (one night), the internet connection is gone even when the light is still green, maybe after the internet provider changes ip?
    I am using wireless lan to get the connection.
    If I then take out the cable from my modem and put it directly into my computer via ethernet, internet signal is there and everything works fine. Sometimes, restarting the airport extreme station and putting out/in the ethernet cable, helps and the internet signal is there for a whole day, but next morning same procedure..
    Thanks
    Stefan

    Think you are suffering from the same problem that '000s of AEB 802.11n users have. I have tried every fix shown on Discussions and nothing has proved to be permanent.
    It is said that Apple is aware of the issue and a permanent fix is coming with 10.5.5 to be released soon. Hope this is right because it is driving me nuts.
    Are you really using 10.4.11 - if so, don't know what your fix is.

  • Have Pixus and 3rd gen Airport extreme. Unable to replace with 5th gen airport extreme

    I have Pixus and a 3rd generation Airport extreme . Unable to replace with 5th generation airport extreme. Problem?

    Ok, thanks for the clarification. I assume that Pixus has provided you with a modem that provided an Ethernet connection to your 3rd Gen AirPort Extreme Base Station (AEBSn) ... correct? If so, then anytime you change networking hardware, it is a good idea to completely recycle power on all of the networking components.
    Please try the following:
    Power-down the Pixus modem, AEBSn, and computer(s); leave them powered off for at least 10-15 minutes.
    Power-up the modem; wait at least 10-15 minutes to allow it sufficient time to initialize.
    Power-up the AEBSn; wait at least 5-10 minutes or until its status light is a solid green. (Note: It may continue to flash amber. This is ok, as it may just require some additional configuration settings, like wireless security to attend to.)
    Power-up the computer(s).
    Network clients connected to the AEBSn, either by wire or wireless, should now be able to access the Internet through the Pixus modem. Please post back your results.

  • Airport Extreme (n-version) as base for extending with Airport Express(old)

    I have a new Airport Extreme that I need to extend - meaning need an ethernet connection on the other side of the room, but I dont want to drag a wire across. I have an extra, and old, Express but I have spent the past couple of hours trying to get it to share/extend the network. Everything seems to configure properly (and I have tried all sorts of options - even setting up a WDS which doesnt seem to work), but when I plug in to the ethernet jack - and then this to my computer - it does not see anything. Help?

    You'll need to check a few settings on the AirPort Extreme because you'll need the information to configure the AirPort Express correctly.
    Open AirPort Utility and click Manual Setup for the AirPort Extreme
    Click the Wireless tab located just below the row of icons
    Jot down the exact name of your wireless network and the security setting that you have in place now. I assume that you already know your wireless network password.
    Close AirPort Utility
    "Hard reset" the AirPort Express (AX) by holding in the reset button on the AX until you see the amber light begin to flash more quickly, keep holding the reset button when this occurs for another 4-5 seconds and then release
    Connect the AX to one of the LAN <-> ports with the ethernet cable
    Open AirPort Utility and click Manual Setup for the AX. You'll be prompted to Switch networks so that you can configure the AX
    Click the Base Station tab (located under the row of icons) to name your AX, establish a device password and adjust Time Zone settings
    Click the Wireless tab
    Wireless Mode = Create a wireless network
    Wireless Network Name = Exact same name as your AirPort Extreme wireless network
    Radio Mode = 802.11 b/g
    Channel = Automatic
    Wireless Security = Exact same setting as your AirPort Extreme network
    Wireless Password = Same password as your AirPort Extreme network
    Confirm Password
    Click the Internet icon and check these main settings
    Connect Using = Ethernet
    Connection Sharing = Off (Bridge Mode0
    Update to save settings. Close AirPort Utility as soon as you see the message that the settings have been stored. The AX will restart in 30-40 seconds. Then restart your entire network by powering everything down. Wait a moment and start the modem first, then the AirPort Extreme, then the AirPort Express and your computers and devices.
    If you decide to use the powerline adapter to allow the AX to be located wherever you want, the AX is already configured to so so.
    Message was edited by: Bob Timmons

  • No Internet via Airport Extreme and Speedtouch Ethernet DSL modem

    I've recently purchased a McBook pro and wanted to create a wireless network. I have a new Airport Extreme Base Station and have successfully set that up, but with no internet connection!
    I can get a perfect connection by hardwiring either of my machines to the DSL Modem directly (via Ethernet cable), but when i connect the Airport Extreme to the DSL Modem via ethernet there is no internet.
    After a bit of research i'm wondering if there is a "bridge" issue... though i have no idea what that means or how to resolve it. Can anyone help?
    Details:
    Airport Extreme 802.11n
    Speedtouch DSL Modem (Thomson ST510 v6)
    G5 Power PC Tower (10.4.11) will connect to the Airport Extreme via ethernet, currently connects to the DSL modem via ethernet.
    MacBook Pro (10.6.4) will connect wirelessly. can currently connect to the internet through the DSL modem via ethernet.
    Dynamic IP via ISP connection via PPPoa

    Hi Steven, I know this question has been answered and is a couple of months old but I think you may be able to help with my set up? I have a Thomson speedtouch 510 v6 modem router provided by Karoo (UK). My other Belkin N modem router has just bust [again] so the Speedtouch is my old faithful backup device. Now, i've never been able to get on ichat with the Belkin as its a mimo n speed and this is apparently not compatible; So i'm now on ethernet with the st510 and have just set up ports for ichat thanks to a thread called http://discussions.apple.com/thread.jspa?messageID=2719419&#2719419.
    What I want to know from you (because I really need a wireless router to get me off this ethernet support system and back on airport) is how you're getting on with the st510 / airport extreme combo now and can you use ichat on it? If so does your connection doctor say full cone in network settings or something else? As I say, I really want to use ichat and have never been able to in 3 years of owning my Macbook Pro. Hope to hear back from you Steven. Regards Steph

  • Why does my airport extreme not recognize my cable modem anymore?

    Why does my airport extreme not recognize my cable modem anymore?

    Have you tried resetting the modem? Power it down and let it rest a moment, then power it back up again.
    Also, some ISPs require physically detaching their cable from the modem for it to be fully reset. Literally unscrew it from the modem. Try that, in conjunction with powering it down.
    Don't do anything with your Extreme, other than powering it down too, in the event the modem reset does not help. Reconfiguring it may be necessary but this is not justified quite yet.

  • I have a Airport Extreme that is dropping the wireless signal alot (several times a day). The green light will go amber but the internet service (ethernet cable) will still be fine. The wireless icon on devices with go away.

    I have a Airport Extreme that is dropping the wireless signal alot (several times a day) The green light will go amber, but the internet service is still ok if your using an ethernet cable directly plugged in. When the light goes amber all devices that is using wireless will lose there wireless icon. The only way to get the green light back is to unplug the Airport device and replug it back in. I tried the reset on the back but still no luck. What is the fix?

    Let's see if I can get this straight.
    You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
    Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
    Correct?
    See this Apple document:
    http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
    The wireless unit on the right of the diagram can be either of the newer Apple base stations.
    Extreme, Express, Time Capsule

  • My airport express is still providing a link to my wifi network but I can't find my airport express on my macbook and i can't link to my bose speakers through it ... any bright ideas?

    My airport express is still providing a link to my wifi network but I can't find my airport express on my macbook and i can't link to my bose speakers through it ... any bright ideas?

    I'm not sure what you mean. You can't find the express to set it up.. or you can't find the network created by the express?

  • HT4145 Does the new Airport Extreme allow "guest network" setup across all my Airports on my network? I have 1 Airport as a router and 6 others as WAP's (bridged)

    Does the new Airport Extreme allow "guest network" setup across all my Airports on my network? I have 1 Airport as a router and 6 others as WAP's (bridged)

    I assume that all of your WAPs are hard wired on the network.
    If.....all of your WAPs are simultaneous dual band Apple AirPort devices like an AirPort Extreme or new AirPort Express.....and.....you have firmware version 7.6.3 (now 7.6.4) installed on all the AirPorts.....and.....you use AirPort Utility 6.3.1 to configure the devices......in theory.....it should work.
    I don't have 6 WAPs, but I do have 3 and the network works perfectly allowing extension of both the "main" and "guest" network.

  • Does Airport extreme include a built in modem ??

    Does Airport Extreme include a built in modem??

    None of the current Apple AirPorts include a built in modem.

  • Does airport extreme or any of the modems work with tds?

    Does airport extreme or any of the modems work with tds?

    Sorry. What do you mean by "tds"?
    Also, Airport Extreme is not a "modem". It is a router.
    Please rephrase your question.

  • HT4600 Airport Express light is solid green but I can not get on the internet.  Any clues as to what is wrong?

    Airport Exopress light is solid green, but I can not get on the internet.  Does anyone have a suggestion how to fix this?

    Would you please provide some more information about your current network so that we can help you? For example, is your AirPort Express the only router in your current network configuration? That is, is it connected directly to a broadband modem or to another router upstream of it? Regardless, what is the make & model of this modem?
    When changing network equipment or when setting it up for the first time, it is always a good idea to perform a completer power recycle of your networking equipment. Please check out the following AirPort User Tip for the details.

Maybe you are looking for

  • Best practice for migrating data tables- please comment.

    I have 5 new tables seeded with data that need to be promoted from a development to a production environment. Instead of the DBAs just using a tool to migrate the data they are insistent that I save and provide scripts for every single commit, in pro

  • Excise invoice without delivery - Milestone and Progressive billing

    Hi all We have a scenario where we need to create excise invoice wihtout delivery We are using order based billing because we have PS(WBS) integration, milestone and progressive billing scenario. We dont  want to use J1is, we want to use J1iin only,

  • Transferring iweb site from 1 mobileme account to another

    i need to transfer my iweb site from one mobile me account to another, but i dont want to buy it in HOPES that i can do it. I want to make sure i actually can. anybody have experience in this?

  • How to run MIDlet in background in J2ME?

    Hi Friends, I am new guy to J2ME and MotoRazr. I just want to run application in background while other application as normal. I am targeting MotoRazr v3xx, MIDP-2.0 & CLDC-1.0. In some post I found that we can use "Backgrounf: True" in JAD file, I t

  • Question about Picture Icons

    We have a list of products on one side of the window. On the other side is one image of one of the products. I wanted to find out if there, I know there is, but..., way to have the picture change when a mouse rolls over another one of the Items? I ba