Trying to connect Verizon wireless router to Airport Extreme but error says Ethernet unplugged.

Trying to connect Verizon wireless router to Airport Extreme and error says Ethernet Unplugged.

So, AirPort Utility running on the Windows Vista desktop can "see" the AirPort Extreme and displays its icon, but gives that error message at some point in the setup process? How far does it get?
Other questions that may help me (or somebody else) understand your problem better:
Which of the pieces were verified as working before the introduction of the AirPort Extreme?
Did you have the desktop computer attached to the Verizon GT704WGB with one of the Ethernet cables you are now trying to use? Which one? Have you tried the other one to be sure it also works?
Are you using the same port on the GT704WGB? Have you tried another one?
If the desktop has multiple ethernet ports, are you using the same one?
Had you done any special configuration of the ethernet port on the Verizon GT704WGB to get it to work with your desktop?
What category ethernet cable are you using? 3? 5? 5e? 6?

Similar Messages

Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except join not extend and I can not get a network on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Rout/

Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except "join a wireless network (which it does) not "extend a wireless network" (Led turns yellow and I can not get a network working on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Router.
Airport gets it address DHCP.

Funny how I can ping the Extreme but the Hard Ethernet ports dont seem to work correctly.
When the AirPort Extreme is configured to "Join" a wireless network, the Ethernet ports are not enabled.
Oddly, the AirPort Express has a special feature that will allow it to to "Join" virtually any wireless network.....and the Ethernet port can be enabled. So, an Express would work for your purpose to provide an Ethernet connection to the media player. This assumes that the Express is located where it can receive a strong wireless signal from your main router.
Note that the Express will not provide any additional wireless coverage when it "Joins".

I'm trying to setup a printer go wireless through my airport extreme, but every time I try to print the printing file gets paused. I'm in loop. PLEASE HELP! (The printer is a Brother 7020 monochrome)

I'm trying to setup a printer go wireless through my airport extreme, but every time I try to print the printing file gets paused. I'm in loop. PLEASE HELP! (The printer is a Brother 7020 monochrome)

I had the exact same problem
It turns out I was using a 20 foot USB cable between the printer and the Airport Extreme and the signal had become to weak to work. Try using nothing more than a 6 foot cable or try a new cable

I own an imac 2011 running osx 10.6.8. I want to the new airport extreme. but it says in the system requirements that it needs osx lion 1.7.5 or later. would it work with my older osx 10.6.8?

i own an imac 2011 running osx 10.6.8. I want to buy the new airport extreme but it says in the system requirements that it needs osx lion 10.7.5 or later. would it work with my older osx 10.6.8?

In order to set up and install the new AirPort Extreme:
Setup and Administration
iPhone, iPad, or iPod touch with iOS 5 or later and AirPort Utility 1.3
Mac with OS X Lion v10.7.5 or later and AirPort Utility 6.3
would it work with my older osx 10.6.8?
Yes, if you set up the new AirPort Extreme using the guidelines above. The 10.6.8 Mac will be able to connect to the AirPort Extreme, but it will not be able to make any configuration changes.
Only the devices listed above can be used to set up and make any changes to the new AirPort.

Trying to connect a wireless router to a switch

We have an 8 port router in the closet(linksys) with the cable connection and in our main room we have a five port 10/100 (By linksys) switch that connects to the system just fine all hardwired, and we have internet already working off of that.
We tried to connect the WRT54G wireless router to the switch because we asked at the store and they said if we had a switch already that's what we'd want. I changed the ip address on the new router to the 192.168.2.1, saved the settings and then tried to plug it into the switch. As soon as we plugged into the switch, anything else connected to the switch stopped getting internet. I also tried to just leave it at the default and same problem. I tried the 'change the IP address to 192.168.1.2 and disable DHCP server and then going into advanced and changing gateway to router and again, same problem. Regardless of what I do anytime I plug that wireless into the switch everything on the switch stops working.
How would we get both the switch and the router to work?

I assume that you want your wireless and your wired computers to all share the same network, and all connect to the Internet through your 8 port router in the closet. And the 8 port router uses the 192.168.1.x address space. --- is that all correct?
If so, disconnect the WRT54G from the rest of your network, then using a computer wired to the WRT54G, do the following:
a) set the "Local IP address" (not the "Internet Connection Type" address) to 192.168.1.2 I am assuming that you are not using this fixed adddress elsewhere in your network.
b) Leave the DHCP server set to "disabled".
c) Wire any port from your 8 port router or switch, to any numbered port on the WRT54G. Do not connect anything to the "Internet" port on the WRT54G.
Note that with this setup, your 8 port router will control your router settings (port forwarding, DHCP server, firewall, etc.). Your WRT54G will only contol your wireless settings.
If you need more help, please state the model of your 8 port router and switch.
Message Edited by toomanydonuts on 08-04-2007 01:39 AM

How to connect a ADSL router to AirPort Extreme?

Hallo,
my local internet service provider forces all costumers to use their modem/router to connect to the Internet using a DSL connection.
I have one external public IP (v4) and the router has an editable IP for the LAN set to 192.168.1.1 .
The ISP router can act as DHCP server and NAT; I can disable the DHCP.
What I would like to do is connect it to the Airport Extreme WAN port and give all the control to the Airport extreme: I want to use his DHCP server, NAT, port forwarding etc.
My problem is that I am able to have Internet connection only if the ISP router has DHCP control and Airport Extreme is set to Bridge mode.
In this configuration, in the Airport Internet configuration panel, the connection is set to Ethernet, IPv4 is using DHCP, Airport IP is 192.168.1.133 and the ISP router has 192.168.1.1 . I also have the DNS IPs set to the ones suggested by the ISP and Bridge mode.
In this way it works: all computers can share Internet connection.
What I am trying to do is:
- disable DHCP in the ISP router;
- in the Airport extreme Internet panel I choose to manually setup IPv4 and I type the same vales it is getting when set to DHCP mode: 192.168.1.133 for the Base and 192.168.1.1 for the router using the ISP dns and I select Share pubblic IP. In the DHCP panel I choose 10.0.1 class.
I save changes and... I got that Internet is no working anymore and I cannot access the ISP router control panel.
Does anybody have suggestion about things to try to not use ISP router DHCP or configuration changes I could try?
Thanks in advance for any help about it!

Thanks for the reply,
at the end it seems that my airport extreme works too BUT with an error message saying "double NAT" and the front led turned to yellow. I have ignored such error because things seems to work and so the led color goes to green.
What I had to do here is:
- set previous router to IP 192.168.1.1
- turn off DHCP on my previous router;
- leave on the NAPT (NAT) service on previous router and set it with start and stop address to the same IP I am using for the Airport Extreme (192.168.1.100);
- open all ports and services on previous router by faking the mac address of the Computer's NIC I was using to configure router. I say faking because previous router wants to know for which computer the ports have to be open, so I had to use the same mac address of the Airport extreme. I cannot type it, previous router will get it automatically when configuring it.
- on the Airport Extreme, Internet side, I had to manually configure Internet options using Ethernet mode: I set the IP 192.168.1.100 for the Airport base. Then I have enabled DHCP on class 10.0.1.x .
Airport extreme seems to work with all features now, I hope that "double NAT" warning will not create any trouble. Anybody knows about that?

Loosing internet connecti when removing router from airport extreme network

Hello. I have an older airport extreme: the alien one. For years I have had the following setup:
Modem --> Belkin Router --> Airport Extreme --> wireless signal to macbook and hardwire line to mac pro. There is also an airport express downstairs acting as a relay to boost my wireless signal. At the time i did it I had other computers so i needed the router to distribute the internet signal. I no longer need the extra capacity as I now only have a wireless macbook and a wired mac pro. Unfortunately when I disconnect the Router and connect the modem directly to the airport I no longer get internet service at either computer. I can't figure it out. The Airport Extreme is already sending all the signals to the two computers...the router is just sitting in the middle doing ostensibly nothing at all. Why, when I take it out of the loop does everything stop working? Thank you!!

Welcome to the discussion area!
Your AirPort Extreme was configured in "Bridge Mode" when it was used with the Belkin router.
Since the Extreme is now the main router, you must configure the Connection Sharing setting for "Share a public IP address".
If you are still using Tiger 10.4.x as your profile indicates, you may still have the application that came with this operating system...AirPort Admin Utility. I cannot remember back 4-5 years to tell you much about this.
If you have upgraded to Leopard or Snow Leopard, you'll use AirPort Utility.
I can help you if you have AirPort Utility. Post back if you need help.

Lost connection to Westell router after Airport Extreme Update

I've looked through the discussions and have seem similar issues but haven't found one that I could say "that's it!"
I use the airport card in my MacBook OS X 10.4.11 to wirelessly connect to my Westell versalink router and have done so for over a year. I don't have an AEB. During updates, I left the airport extreme update checked. Why? I probably wasn't paying enough attention.
So now I cannot connect at all - at home. It's stating that my password is incorrect. I can connect at work; no password is required.
I went to the Westell website and changed my Network (SSID) name and password. Now, I'm picking up this new network but I'm still being told the password is incorrect.
Can I uninstall the Airport Exteme Update (and pray that it works) or is that too easy an answer?

You are not alone, have a look at this thread:
http://discussions.apple.com/forum.jspa?forumID=1015&start=0
Unfortunately, it appears that the 2007-02 update has broken Airport running on Macbooks and Macbook Pros that attempt to access wireless routers using WPA. I've spent a lot of time looking for a solution, and at this point there appears to be no reasonable fix until Apple corrects this serious flaw. If you have AppleCare, perhaps a phone call to them would help them become more aware of the situation. Until they do, many of us are without the use of Airport, particularly where it is not possible to switch off WPA in a shared environment (such as my office).

Linksys Wireless Router to Airport Extreme

Equipment:
- Linksys Wireless router connected via ethernet to iMac in Living room.
- G4 Powermac in sons bedroom
I have an Airport Extreme also. Can I connect this via ethernet to the G4 and broadcast wifi to the G4 from the Linksys router in the living room?

Welcome to the discussions!
What you are asking is if the Linksys can broadcast a wireless signal to the AirPort Extreme and then have the AirPort Extreme connect to the G4 using ethernet.
The short answer is "no". For more details, please read on.
This is not possible because the ethernet ports are not active on the AirPort Extreme in this type of configuration. The ethernet ports on the AirPort Extreme would only be active if the device were configured to "extend a wireless network".
But, the AirPort Extreme can only "extend a wireless network" from another Apple device as it is not compatible with the products of other manufacturers for this purpose.

Trouble connecting to wireless from installed Airport Extreme

I just installed an Airport Extreme card into my dual 1.8mhz G5. I followed the steps on installing and everything seems to work. It is recognized in the network preferences as an Airport option. I have been unsucessful in connecting to the wireless connection. I do have a laptop G4 and I am able to connect without trouble. But I am not able to figure out why I can not configure the G5 to see the same wireless network. I have typed in the same wireless name as the laptop into "other" on the G5 but it does not recoginize it. Please advise.

As I'm typing, I'm connected wirelessly. Don't ask me how it happened. I had installed Airport utility and it couldn't find the network. I opened up Network Connections through the control panel, immediately found the network, clicked on Change Settings of this Connection, clicked Configure, didn't change anything, then clicked on View Status of this Connection, and lo and behold, I'm suddenly connected. Tell me I'm not crazy!

HT4262 How can I connect 6 computers simultaneously to Airport extreme?

I have tried troubleshooting several ways and the some computers work and others don't. How can I connect 6 wireless computers to Airport Extreme?

Matt
Is it possible to speak on the phone? The situation is so convoluted it might be easier to help me get back on track in person. When I first had this issue I got on an apple site that had a chat room in which I typed in my problem. After several missives back and forth, the apple technician asked for my number and we spoke on the phone. The technician walked me through rebooting the actual airport plug (as opposed to the router box) and got me up and running. Do you know how I can relocate that chat site for technical support?
Thanks
David

Using time capsule model A1409 and trying to use it as only backup. Already have Verizon wireless router. Do not know which cable port to use in back of time capsule. And also it is asking for password. Have tried all of mine and it will not work.

Want to us my time capsule model A1409 as only backup. 2 TB hard drive.
Already have Verizon wireless router. Do not want to use Time capsule as router, only back up for iMac.
Do not know which cable port to use in back of time capsule to Ethernet port back of my iMac.
And also it is asking for password for the server John Garland's Time Capsule so Time machine can access it..
Have tried all of passwords can think of and none work.
Held the reset button for one second on back of capsule and do not see if anything happened.
What a conundrum.
Appreciate any help to get this working.
Thanks,
John R

I have a 2TB Timecapsule and really only use it for Time Machine backups. But the Wi-Fi side is used to sync my iPad at times.
Mine is wiredup thus;
Eth cable from iMac to modem (not the WAN port should you have one), then eth cable from modem to T/Cap in the WAN port (bottom port with an O sign above it)
I believe when its connected up you may have to set up a wireless network. Follow the instructions to set up Wi-Fi and Network
and then give it a password. The WiFi icon should appear in the menu bar where you can switch it on or off.
Its been sometime since I set it with the help of Apple Techs so I might be a bit rusty.
Alan

My Ipad and itouch cannot be connected ti wireless router tried changing setting still cannot connect

my Ipad and itouch cannot be connected ti wireless router tried changing setting still cannot connect

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Should I disable the wireless capabilities of my Bigpond modem/router when Airport Extreme is connected?

Should I disable the wireless capabilities of my Bigpond modem/router when Airport Extreme is connected? I'm told that it's better to only use the WiFi capabilities of the Extreme and leave the Bigpond to feed to the extreme.

No, bridge mode would not be the correct setting for this.
Instead, look for a "wireless settings" tab or page that will provide the option to turn off or disable the wireless radio of the BigPond router.
If you are still having difficulty, it would be a good idea to post your question on a BigPond support forum or contact your Internet Service Provider.
Contact Technical Support - BigPond

Trying to connect my wireless g router

Hi,
I am trying to connect my wireless g router (WRT54G) to my cisco router from my company. My cisco router was configured by my company so that I can use the office phone. I need wireless access in my house (I work from home), and so I am trying to connect the WRT54G to the cisco router.
I followed the instructions on the setup CD, and it got to the point where it checks the configuration, and then it crashes, and wants to send an error report to microsoft (which I don't understand, but is another question for another time!)
I am completely at a loss here, and don't know what to do. I barely understand this whole internet/router/W.A.P./network thing as it is, and am frusterated.
Any suggestions?
Thanks!
Shelley

Don't use the CD. You are running behind a router already and you don't want to set up two chained routers. Instead set up the WRT as access points like this. Be sure to pick a valid and free LAN IP address in your current LAN for the WRT.
To secure the wireless you also have to do the following:
* Change the wireless network name (SSID) from "linksys" to something unique (Wireless tab).
* Enable wireless security. Use WPA2 Personal or WPA Personal. Use AES+TKIP for WPA2 or TKIP for WPA. Enter a strong passphrase.
* Change the default password of the router ("admin") on the Administration tab.

Trying to connect Verizon wireless router to Airport Extreme but error says Ethernet unplugged.

Similar Messages

Maybe you are looking for