Trying to console into air-lap1252ag-a-k9 v01

I have just recently purchased this device on ebay as a used product from a bankrupt company, which was selling off old equipments. I am trying to attempt to console into the ap, but am not able to do so, sucessfully. I am using a usb type console to blue rollover cable on com3. I have the power injector plugged in. However, the status light is blinking only. I have tried to use putty to get into the ap, but nothing happens as I tried to use serial, com3, 9600 baud, 8 data bits, 1 stop bits, none pairty, and flow controle none. It doesn't sucessfully load. Am I doing something wrong here? I even tried the mode button to reset the ap as well and it doesn't help at all. I hope someone here can help me with this?

Console into the ap and power cycle it.... post what shows on the console.

Similar Messages

  • Problem with setting up AIR-LAP1252AG-A-K9

    My company recently handed me 2 used 1252 AIRONET APs that they picked up somewhere to replace and add on to the current AIR-AP1121G-A-K9 that are currently used. I've been successfull at connecting via a Serial Connection in an attempt to the AP's IP via the CLI. But further attempts to connect to the AP via a web interface to continue setup have been a failure. After some research, can anyone confirm that LAP series products can only run Lightweight IOS, hence the need for a CISCO controller, or can I try to flash the firmware to make it into an autonomous AP. I've been fighting with this for a couple days and its getting frustrating. Am I blindly missing something? I've tried resetting the AP to default several times, but no luck. Much thanks!!!                  

    The WAP can run either controller-based IOS or autonomous IOS (aIOS).  Console into the WAP and reboot.  Post the entire bootup process.

  • I am trying to remote into a Windows Server 2003 from a Windows 7 machine and having issues

    I am trying to remote into a Windows Server 2003 from a Windows 7 machine.  It says "The terminal server has exceeded the maximum number of allowed connections".
    My first stop in trying to solve this problem was here:
    [URL="http://www.howtogeek.com/howto/windows/command-line-hack-for-terminal-server-has-exceeded-the-maximum-number-of-allowed-connections/"]howtogeek.com[/URL]
    And it says:
    [I]
    [INDENT]This problem happens because Windows only allows two remote terminal services connections when you are in administrative mode, and you’ve either got two people already on that server, or more likely, you’ve got a disconnected session that still thinks
    it is active.
    The problem with this error is that you have to actually get on the server console to fix the problem if the server isn’t in a domain. ([B]If you are in a domain, then just open Terminal Services Manager and log off or disconnect the sessions[/B])[/INDENT][/I]
    So it seems to suggest that all I have to do really is to run the  Terminal Services Manager but I cannot find it.
    This web site from mssqltips.com [URL="http://www.mssqltips.com/sqlservertip/1981/remote-desktop-error-terminal-server-has-exceeded-the-maximum-number-of-allowed-connections/"](click here)[/URL] says all I need to do is first execute "mstsc /
    admin" from the command line.  But, when I do that, I get a message when I try to remote to the server, that says this: "To log on to this remote console session, you must have administrative permissions on this computer".
    So, what now?  What do you suggest?

    Hi Bobby,
    Yes, it is by design. By default, Windows Server only accepts two concurrent administrative sessions (Administrative Mode). It means that only two administrators can work on the server at
    the same time.
    If you would like more concurrent sessions, you need to purchase RDS CALs, install Terminal Services related server roles with proper configurations on the server.
    Remote Desktop for Administration (server 2003)
    http://technet.microsoft.com/en-us/library/cc785186(v=ws.10).aspx
    What Is Terminal Services?
    http://technet.microsoft.com/en-us/library/cc782486(v=ws.10).aspx
    Terminal Services Configuration
    http://technet.microsoft.com/en-us/library/cc787078(v=ws.10).aspx
    Purchase client access licenses
    http://technet.microsoft.com/en-us/library/3660ac5a-7468-48d3-b7e8-5529de8fb6c5
    Thanks.
    Jeremy Wu
    TechNet Community Support

  • I have tried with my ipad air and a friends ipad to mirror the contents to a samsung smart tv via appletv and cannot either to work.I have spent over 2 hours today on live chat with apple support with no resolution.Any ideas please?

    i cannot mirror from ipad or ipad air to a samsung smart tv via appletv.Any ideas please?

    I have tried with an Ipad Air and Ipad using Op System 8.0.2 to mirror their contents to the screen of my Samsung Flat Screen Flat TV via the latest make of Appletv.I have spent over 2 hours going through all settings etc with Apple Customer Service Live Chat.They cannot find or replicate the problem and says it is all working fine.My TV screen displays, when i go into mirroring,  "ready for connection - on your device launch Allshare Cast".Nothing happens although i have agreed with Apple Support that all settings are on and are correct.Can anyone help please, as Apple Support cannot?

  • Converting the web app into AIR app leads errors

    Hi all,
    I am new to flex, i am trying to convert a web app into air app.
    I changes the tags and when i complie i get the below 3 error popups with dismis and continue buttons on the bottom right..
    Error: Error #2067: The ExternalInterface is not available in this container. ExternalInterface requires Internet Explorer ActiveX, Firefox, Mozilla 1.7.5 and greater, or other browsers that support NPRuntime.
    Error: Error #2067: The ExternalInterface is not available in this container. ExternalInterface requires Internet Explorer ActiveX, Firefox, Mozilla 1.7.5 and greater, or other browsers that support NPRuntime.
    TypeError: Error #1009: Cannot access a property or method of a null object reference.
    Any help would be greatly appreciated.
    Thanks in advance.

    Thanks peter.
    commenting those lines avoids the first 2 errors but still i am getting the below errors.
    this is a microstrategy flex project.
    Error #1009: Cannot access a property or method of a null object reference.
    at com.microstrategy.web.vf.viewer::MstrWindowedApplication/handleCreationComplete()[Z:\Flex \projects\VisFrameworkAIR\src\com\microstrategy\web\vf\viewer\MstrWindowedApplication.as:9 9]
    at flash.events::EventDispatcher/dispatchEventFunction()
    at flash.events::EventDispatcher/dispatchEvent()
    at mx.core::UIComponent/dispatchEvent()[C:\autobuild\3.2.0\frameworks\projects\framework\src \mx\core\UIComponent.as:9298]
    at mx.core::UIComponent/set initialized()[C:\autobuild\3.2.0\frameworks\projects\framework\src\mx\core\UIComponent.as :1169]
    at mx.managers::LayoutManager/doPhasedInstantiation()[C:\autobuild\3.2.0\frameworks\projects \framework\src\mx\managers\LayoutManager.as:718]
    at Function/http://adobe.com/AS3/2006/builtin::apply()
    at mx.core::UIComponent/callLaterDispatcher2()[C:\autobuild\3.2.0\frameworks\projects\framew ork\src\mx\core\UIComponent.as:8628]
    at mx.core::UIComponent/callLaterDispatcher()[C:\autobuild\3.2.0\frameworks\projects\framewo rk\src\mx\core\UIComponent.as:8568]

  • My ipad is flat and when I plug it in to charge it just repeatedly turns on and then turns off but isn't charging. I tried to plug into itunes but it just goes through the same ritual and can't maintain connection to itunes. What should I do ?

    My ipad is flat and when I plug it in to charge it just repeatedly turns on and then turns off but isn't charging. I tried to plug into itunes but it just goes through the same ritual and can't maintain connection to itunes. What should I do ?

    1. Reset iPad
    2. Try another wall socket
    3. Try another cable (make sure it's an original Apple cable)
    4. Try another charger (make sure it's an original Apple charger)
    5. Clean Lightning port with compress air or new paint brush

  • Can't Console into ESW-520-24P Switch, Need help.

    Hi,
    We have 3 ESW-520-24P series switches.
    I can not console them because by default they have a security profile attached into it for "Console Only" and It is set as "Deny".
    I can't modify or delete it because it's a default security policy.
    We can do console into ESW-540-24P series switches without any problems.
    Can someone share any solutions to gain console access for these switches?
    Any one from Cisco TAC support?
    Thanks in advance.
    Mansur.

    Hi Devicarr,
    Thanks for your reply.
    I can set the VLAN and Management IP address using the web interfaces.
    But when I am trying to connect it via console it is not responding. I reset it to factory default and then found from the web control panel/interface that the switch has an "Access Authentication" under that it has a "Access Profile" and the profile has a default or built in profile attached says "Console Only" and it has a rule like "IP Source = 0.0.0.0/32 Permit = Deny".
    I tried to delete or modify it even I tried to add a new rule to allow the console access but failed.
    Does this switch series "ESW-520-24P" by default Console disabled when manufactured or ELSE? Please provide me your valuable suggestions.
    Thanks in advance.
    Mansur.

  • Cannot console into a 3005 VPN Concentrator

    Hi all,
    I recently acquired a 3005 that was supposed to be working.  And in all fairness, it seems to be.  The status light is yellow while it boots and a few seconds after turning it on, it goes to solid green.
    I have tried everything I can to console into this unit.  I used TeraTerm with a USB to serial adapter and a straight through serial cable with the settings suggested in the manual and I get nothing.  Is there something I could be doing wrong?  Is there any other way I could try to test this unit?  Is there anything else you guys can think of to try?
    Any help is much appreciated.  This has frustrated me to no end.  I have tried mutliple computers, multiple cables, multiple com ports.  I'm fairly positive I'm doing something wrong, but I have no idea what. 
    Here are my terminal session settings:
    BR:     9600
    Data:   8 Bit
    Parity: None
    Stop:   1 Bit
    Flow Control:  Hardware
    This is per the manual.
    Thanks,
    Brandon

    Finally got it!  Ended up just making a straight through cable.  The cables that I thought were straight through were not.  Made one with two RJ45 to DB9 adapters pinned out to standard serial on each end of a cat 5. 
    Brandon

  • Error CNDP/005 when trying to log into a SAp System

    Hello everyone,
    when trying to log into a SAP System, i get the following dump:
    Error analysis
        Short text of error message:
        Control Framework: Data stream error. Transaction terminated.
        Long text of error message:
         Diagnosis
             The data stream from the frontend could not be interprete
         System Response
         Procedure
             This error is very probably due to an error in the fronte
             software installation or an obsolete version. Inform your
             administrator.
         Procedure for System Administration
             The frontend should have at least the same version as the
             release. Install the correct frontend. If the error conti
             occur, inform SAP.
        Technical information about the message:
        Message class....... "CNDP"
        Number.............. 005
        Variable 1.......... " "
        Variable 2.......... " "
        Variable 3.......... " "
        Variable 4.......... " "
    It occurs directly after inserting my User/Password and pressing enter.
    My SAP GUI: Version 710, Patchlevel 11
    The strange thing about that:
    Last week i didn't have this error and i didn't change anything.
    I already uninstalled, reinstalled and rebooted but it didn't work.
    I would appreciate some help.

    I upgraded to patchlevel 13, which solved the problem.

  • What to do when trying to log into my iCloud and it says "this apple iD is valid, but it's not an iCloud account"?

    What to do when trying to log into my iCloud and it says "this apple iD is valid, but it's not an iCloud account"?

    If you have not already created an iCloud account elsewhere you cannot do so on  PC, and that is the error message you will get. You can create an iCloud account on a Mac or an iOS device and then you should be able to sign into it in the iCloud Control Panel in Windows.

  • I am trying to get into my Game Center app but every time I tap on the app it opens too a blank white screen. I have tried several times to reset my phone but I get the same result.

    I am trying to get into my Game Center app but every time I tap on the app it opens too a blank white screen. I have tried several times to reset my phone but I get the same result.

    Hello there Sweebs44,
    It sounds like you are tapping the Game Center app to open it, but the screen is blank. I recommend signing out of your account:
    Go to Settings > Game Center, where you can:
    Sign out (tap your Apple ID)
    From: iPhone User Guide
              http://help.apple.com/iphone/7/#/iph6c493cac
    Then close all the running apps:
    iOS: Force an app to close
    http://support.apple.com/kb/ht5137
    Double-click the Home button.
    Swipe left or right until you have located the app you wish to close.
    Swipe the app up to close it.
    When you have done that restart the phone sign back into your account and try again:
    iOS: Turning off and on (restarting) and resetting
    http://support.apple.com/kb/ht1430
    Thank you for using Apple Support Communities.
    Take care,
    Sterling

  • Mac keeps trying to log into a Windows server with old password.

    My iBook for some reason is trying to log into a server at work we use to share files on (let's called it Xserver). I recently discovered through logging my network traffic on my router at home, that my machine was still trying to access XServer.rr.com Xserver.socal.rr.com even when I was not in the office. It doesn't stop trying, over and over and over it goes, trying to find XServer. I was wondering why my account on XServer kept becoming Locked Out (Windows Server), and this is obviously the answer because it's not using the correct password.
    How can i find out where OSX is instructed to connect to XServer automatically and keep trying, and tell it to stop?

    Look in SystemPreferences>Accounts>yourAccount...and then into Login items. see if this server login is set to be automatic there.
    If it's just a wrong password you need to fix, look into Utilities>KeychainAccess...see if this server is in there, remove it. Or do Keychain FirstAid.
    There is an automount function somewhere, but I forget where that is.

  • I get an error message when trying to sign into the support community with another Apple id. On the pick a username screen I get "an account utilizing this address already exists...." despite trying a few usernames. Anyone know how I can resolve this?

    I get an error message when trying to sign into the support community with another Apple id. On the <pick a username> screen I get "an account utilizing this address already exists.Only one account per email address is allowed on the Apple Support Communities" despite trying a few usernames. Anyone know how I can resolve this?

    This problem has been driving me demented. The instructions that Ivan gives have partially worked for me. By following his link
    "How to find out if you have multiple Apple IDs" I was able to identify that yes I did have two apple accounts using the same e mail address. One was very old that I used to use for the forum boards and one is my much more recent ID that I use for everything these days. So I changed the e mail address for the old account which is associated with these discussion boards and that's the account that I am now posting this from. However even though the two accounts now have different e mail addresses when I try to log onto the boards with my more recent main apple ID I still get all the same errors as described at the start of this thread by rodgers_j. And of course that's the one I want to use so that I only have one itunes account for everything.
    So if anyone has any more hints I'd be very grateful.

  • Trying to get into the app store and it asks for my password. The problem is that it is showing an Apple ID I don't use ghosted in. I can't figure out how to use my correct ID.

    Trying to get into the App Store to update some apss. It asks for my password but the problem is that it is showing ghosted an Apple ID I don't use. Can't figure out how to fix it.

    You installed a hacked app, originally from the Mac App Store. It contains the receipt for a different app, downloaded using an account that you don't control. You need to identify and remove the hacked app.
    Important: The app you need to remove is not necessarily the one named in the App Store alert. For example, if the App Store says you need to update "Twitter," the hacked app may be "Angry Birds" or something else entirely. Don't make any assumptions about which app you're looking for. To find it, you have to carry out a systematic search.
    Triple-click anywhere in the line of text below on this page to select it:
    kMDItemAppStoreHasReceipt=1
    Copy the selected text to the Clipboard by pressing the key combination command-C.
    In the Finder, press command-F to open a search window, or select
    File ▹ Find
    from the menu bar. In the search window, select
    Search: This Mac
    from the row of tokens below the toolbar. Below that is a popup menu initially showing Kind. From that menu, select  Other...
    A sheet will drop down. In that sheet, select Raw Query and click OK or press return.
    Now there will be a text box to the right of popup menu. Click in that box and paste (command-V).
    The search window will show all the App Store products you've installed. Compare those search results with the list of your purchases from the App Store. To see the complete list, you may need to unhide hidden purchases. If any apps were download from the App Store using other Apple ID accounts that you control, sign in to the store under each of those ID's and check the purchases.
    At least one of the items listed in the search window is not among your purchases in the App Store. Move each such item to the Trash. You may be prompted for your administrator password. Empty the Trash.
    Log out and log back in. Test.

  • Ok... i am trying to sign into my apple account in the itunes store on my ipod and i have all the correct data for my credit card and it says " your payment information does not match your banks records. try again or nenter a new payment method. " help me

    ok... i am trying to sign into my apple account in the itunes store on my ipod and i have all the correct data for my credit card and it says " your payment information does not match your banks records. try again or nenter a new payment method. " what does this mean and how can i fix it??

    - See:
    ]iTunes Store: My credit card's security code or zip code does not match my bank's records
    - If still problem contact iTunes by:
    Contact iTunes

Maybe you are looking for