Trying to create a wireless network - i think!
I hav an ABS connected to the internet. I have an AExp connected to my stereo system. I can access the internet fine from my ABS, and i can play music over my system using the AExp. But not at the same time. So, I'm trying to set up a network so that I can be online through my ABS while listening to music through my AExp. I've tried over and over to no avail at creating a network. I'm assume this must be possible - What am I over looking? or Am i going about it the wrong way?
thanks
thanks for the reply. the problem i experience when following the instructions "How to join an existing wireless network in client mode" are as follows:
Using AirPort Setup Assistant:
1. Plug AirPort Express into a power outlet.
2. On your computer, join the wireless network created by AirPort Express.
3. Open AirPort Setup Assistant. Mac users: Find it in /Applications/Utilities/. Windows users: On the Start menu, point to All Programs and click AirPort.
4. When you see the Introduction screen, click Continue.
5. Select "Set up a new AirPort Base Station" and click Next.
result is an error mssg:
NO NEW AIRPORT NETWORKS WERE FOUND
Please make sure your AirPort Base Station is plugged in, in range of your computer, and then click Continue to scan again
I'll try "change setting on an existing ABS" instead of "Set up a new AirPort Base Station". I'll go through the entire process and in the end the AX still won't join.
Using AirPort Admin Utility:
while proceeding through Airport Admin everything seems to work and it appears to update but then I loose complete contact with the AX.
Similar Messages
-
I have a closet with Wired connections from all over the house terminating in it. I also have the internet modem and a switch in this closet. My old setup was a netgear in the closet creating a wireless network and also feeding the Ethernet ports all over the house. In my room, I had an Airport express (a month old) bridging the wifi to make the wifi network larger. The Express was hard wired from the wall and my mac mini was using it's wifi (printer was plugged into other ethernet port). Everything was working great.
Fast forward to last week. My Netgear died. So, I bought a time capsule. My plan was to move the Express to the closet and have it create the wifi network and also then run cat 5 cord from express to the switch to feed all the wired wall plugs. Reset it and set it up to create the wifi network as well as DCHP NAT. Wireless was running great on it. Then I plugged in the Cat 5 in the second Ethernet Port to the switch. Wifi stopped working and none of the computers would connect using wired connections either. They would see a 'network' but nothing would work. I would unplug the Cat 5 feeding the swtich and the wireless would start working again. Plug the Cat 5 back in and wireless would stop.
So I thought I would try the Time Capsule in the closet and see if I could get it to work. Pretty much the same thing, except at this point I figured out if I went in and told it NOT to create a wifi network the wired portion worked fine and all the wired computers in the house worked fine. Of course, then I didn't have Wifi.
I'm not clueless when it comes to networking, but I can NOT figure this out! Can either the Time Capsule or Express Create the wifi network AND also feed the data to the switch for all the wired computers?
To simplify this is what I want my end result to be. I prefer the Time Capsule to be the wireless connection extender, but if I have to have the Express do it, I'm fine with that.
1. Express in the closet creating the wifi network as well as feeding the data to the wired connections via my switch.
2. have the Time capsule in my room at the opposite end of the house plugged into the hard wired connection to extend the wrieless network as well as have wired connections such as my printer and my Mac Mini.
If I can get #1 to work, I don't think I'll have any problems with #2. Help!I have an equally complex setup with a managed switch actually but I have never seen the TC have this kind of issue.
What I do notice is you have changed the TC from defaults.. you are using a non-default IP range.
I have run across issues like this where people move things from default.
I would like you to start over.. factory reset the TC. That will set it back to default router mode.
Do the min setup on the TC..
1. Change all names from what you were using. That includes the TC name and wireless name/s
Make them short, no spaces and pure alphanumeric because that is the correct way to network. Apple default names with spaces and apostrophes are fundamentally bad.
2. With just the TC plugged into the switch.. and a single computer connected by ethernet. Power cycle the whole network.. this allows the switch to clear all the old MAC address.
3. Test on the computer just ethernet. Turn the wireless off.
The computer must use dhcp and must get an ip from the TC.
It has to get the correct Router.. ie Gateway.. I wish apple could stick with proper network terminology.
And it must get same address or valid DNS server address/es.
If it fails.. please plug ethernet directly to the TC.. bypassing the switch.
You should get the standard IP addressing and internet connection.
If not please post the screenshot from the Mac of the network preferences showing the ethernet setup.
I need to see what address it does get. I need you to make sure the ethernet is the TOP of the list. So rearrange the order of network connection. With the airport off it should just go to the top of the list.
If it appears to be working .. but a browser cannot connect, open a terminal and ping an internet address.
Ping the actual gateway address the ISP gives you and ping the ISP dns address. -
The Airport Extreme is a 4th Gen unit. I just want to keep the TC wireless name to go further through my house.
The Ethernet connection will be from one of the LAN <-> ports on the TC to the WAN port (circle of dots icon) on the AirPort Extreme.
Then you can use AirPort Utility - Manual Setup to configure the AirPort Extreme as follows:
Click the Wireless tab located just below the row of icons
Wireless Mode = Create a wireless network (Not "extend a wireless network" as many users incorrectly think)
Wireless Network Name = Same name as your TC network
No check mark needed next to "Allow this network to be extended"
Radio Mode = Automatic
Channel = Automatic
Wireless Security = Same setting as the TC network
Wireless Password = Same setting as the TC network
Confirm Password
Click the Internet icon
Click the Internet Connection tab
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Update to save settings and restart the entire network
Computers on the TC network will now be able to move to the area where the AirPort Extreme is located and not have to "switch" networks. This is known as a "roaming" network. -
How can I create a wireless network in my office for my itouch?
I am in an office Windows environment with a G3 Mac that is connected to the internet via the Ethernet port. I can get to the internet with my Mac through a Proxy server. I have tried to setup up Airport to get through the firewall without any success. Is it possible to create a wireless network for my itouch if I install an Airport card in the Mac, start Internet Sharing and install Airport Express? I have no experience with the Internet Sharing options in OSX. I am assuming that my Mac with an Airport card would pass the internet connection to Airport Express. Airport Express would then create a wireless network for my itouch to connect to the internet. Any advice is appreciated as I would really like to get to the internet with my itouch.
You don't need the AirPort Express to do this.
You can set your Mac to share it's wired connection over the wireless port and the iTouch can connect directly to the Mac.
You could also do it with the AirPort Express, but you don't need to - it's overkill for what you've described. -
Can't create a wireless network without a wireless card on my Mac
Help!
O.k. I tried searching the forums for an answer but the odd nature of my problem, and the immense database of topics made it very difficult to find a similar post.
The general issue/idea:
Run a wireless network using Airport Extreme - Connect desktop mac via ethernet and Roku player via wi-fi. Can't get the desktop mac to connect via ethernet when I restart the network/Airport Extreme.
My Father in law has my old computer; It's a PowerMac G5 (Dual 1.8GHz CPUs) running OS 10.5.8), connected to internet via cable (TimeWarner) modem. It does NOT have an Airport or Airport Extreme card installed. The computer works fine, and I don't believe that I 'need' an Airport Card in order to use the Airport Extreme (it's a brand new/refurbished model) in the manner described below.
I would like to use the Airport Extreme to generate/run a wireless network (Do I need an Airport Card in order to generate/run a wireless network? Doesn't the AE actually do that?), connect the desktop Mac to the network via Ethernet (I shouldn't need an Airport Card to do that, should I?) and connect a 'Roku Player (802.11g capable) to the network via wi-fi.
As far as I know, this should be possible.
Basic steps/as I understand them:
A. Connect ethernet from cable modem to AE.
B. Connect ethernet from AE to desktop Mac.
C. Create the wireless network using desktop Mac and Airport Utility.
D. Restart AE to start the wireless network running.
E. Connect Roku to wireless network over wi-fi.
I have no problems with A & B. Once the AE is connected to the desktop Mac, I'm able to get internet via ethernet as it passes through the AE. I can then create a wireless network (step C.) using the Airport Utility (and setup assistant). The problem starts after I've configured the wireless network.
Once I've configured the wireless network, the Airport Utility software prompts me to restart the AE in order to start the wireless network.
As soon as I restart the AE, my desktop Mac tries to connect to the 'wireless' network, even though it's already connected via ethernet. I don't have a wireless card in the Mac, and I don't want to connect the desktop using wi-fi/wireless. It's connected via ethernet, works fine during configuration, and I don't ever anticipate a desire to connect the desktop via wi-fi.
No matter what I do, I can't get the desktop to connect via ethernet. The only network connection option I'm offered is 'Rescan'. O.k. the desktop can't find the wireless network (because it doesn't have a wireless card), and I'm unable to continue with the Airport Utility. I can't make any further changes to the network (the options to manually change the network configuration are not available as the desktop Mac cannot currently talk to the AE - It's still trying to connect wirelessly), and the desktop has no internet connection as it's trying to connect wirelessly.
*How can I...*
*Setup/run a wireless network, while keeping the desktop Mac connected via ethernet?*
I'm perfectly willing to factory reset the AE and start over.
Any help appreciated.
Thwarted by the network.
- RobertMy Father in law has my old computer; It's a PowerMac G5 (Dual 1.8GHz CPUs) running OS 10.5.8), connected to internet via cable (TimeWarner) modem. It does NOT have an Airport or Airport Extreme card installed. The computer works fine, and I don't believe that I 'need' an Airport Card in order to use the Airport Extreme (it's a brand new/refurbished model) in the manner described below.
That is correct, you could connect the PowerMac G5, via Ethernet, to the AirPort Extreme Base Station (AEBS) or any other wired router for Internet access. You do NOT need an AirPort Card for wired access ... ONLY if you want the G5 to connect to a wireless network.
I would like to use the Airport Extreme to generate/run a wireless network (Do I need an Airport Card in order to generate/run a wireless network? Doesn't the AE actually do that?)
That is correct, the AEBS is a wireless router that can provide a wireless network. The AirPort Card, on the other hand is a wireless adapter used to allow a Mac to connect to a wireless network, created by any wireless router ... not just those provided by Apple.
As far as I know, this should be possible.
Basic steps/as I understand them:
A. Connect ethernet from cable modem to AE.
B. Connect ethernet from AE to desktop Mac.
C. Create the wireless network using desktop Mac and Airport Utility.
D. Restart AE to start the wireless network running.
E. Connect Roku to wireless network over wi-fi.
Yes, these are all good assumptions.
As soon as I restart the AE, my desktop Mac tries to connect to the 'wireless' network, even though it's already connected via ethernet. I don't have a wireless card in the Mac, and I don't want to connect the desktop using wi-fi/wireless.
Do you actually have an AirPort Card installed in the G5 now? If so, then it might be possible that the "firing order" for network connectivity has AirPort at the top of the list under System Preferences > Network. Just change the order to have Ethernet at the top and disable AirPort to ensure that the G5 connects by Ethernet only. -
Connection timeout error trying to connect to wireless network
Going nuts...
I have my Time Capsule plugged into an outlet that runs back to my switch (Netgear) which in turn goes into my modem (AT&T uverse).
(the switch runs out to about 6 ethernet outlets in my house)
Everything was working grand until I screwed something up, no idea what, of course!
I have set my Time Capsule set up...
In the AirPort Utility
AirPort tab
Wireless mode:create a wireless network
Connect using: Ethernet
Internet tab
Connect using: Ethernet
Connection sharing: Off (Bridge mode)
From these settings I can see the wireless network I have set up, but I can't connect to it (get a 'connection timeout' error when trying to connect to the wireless network using my laptop)
When I try to change to Conenction Sharing to: 'share a public IP address' or 'distribute a range of IP address', then I get other errors... (DHCP Beginning and DHCP Ending Address Errors).
Any advice would be great - thanks!Bridge Mode is the correct setting for your Time Capsule.
To aid in troubleshooting, I suggest that you temporarily move the Time Capsule close to the Uverse router and connect directly to one of the Ethernet ports on that device. Test to see if your wireless is working.
If yes, then move the Time Capsule again and this time temporarily connect to the Ethernet switch to test that way.
Keep working your way outward, testing as you go. If the wireless works on the first test when you connect directly to the Uverse router, at some point, you will find the connection problem. It's almost always something simple, like an Ethernet cable that is not making a good connection with one of the Ethernet ports. -
Using airport Express on a hotel ethernet to create a wireless network
Hi there, yesterday I bought an airport express as I was lead to beleive it was the perfect device and simple to set up with regards to creating a wireless network from a ethernet connection in a hotel room. I seem to get a green light and seem to aquire a valid IP address of 192.168.2.102 and the AE utility doesn't state I have any problems and yet I cannot connect to the internet. I am from the UK and currently in Honk Kong on business for the next few days and desperately need to get a wireless connection sorted. I have read through many of the archives on these forum pages and it is still not certain to me whether I should be using bridged mode or not?
btw, I can connect my pc and get internet access without any problems by ethernet directly into my pc.
can someone advise me of the settings I should use given my scenario (ethernet connection in a hotel room). Given how much tme I have invested trying to get the AE to connect to the internet I would prefer to stick with it and get it workShort rather than taking the Airport Express back to the Apple store tomorrow and moving to a hotel with wireless and not ethernet connection.
Help appreciated
RussellbHello, thanks for your suggestions. I have tried setting up the AE using my girlfreinds Win XP computer instead of my vista one and it setup 1st time without any problems. In fact, the options I got presented with were slightly different. Shocked at what a difference installation and setup can be from using a Vista laptop to a XP netbook. Maoin thing it is now working and you were correct about using it in bridged mode so many thanks.
Russyb -
HELP - Problems with Time Capsule when creating a wireless network
I am trying to change my current D-Link router for my TC (so that the TC creates the wireless network instead of the D-Link). However, when I connect the TC directly to the modem it states there is no internet connection?
Anyone have any ideas on how to resolve this?Is the modem a router as well??
How is the dlink setup... is the modem adsl or cable?
If cable, did you reset the cable modem when you changed over. Power down and leave for 5min.. then power up again.. did the TC get the public IP on the wan interface .. use the airport utility to check.
If it fails wait longer time.. or contact cable company to reset the port.
If it is adsl modem router, or cable modem router
Bridge the TC.. go to the manual setup of airport utility, internet tab, connection sharing and select bridge.
If the dlink uses pppoe now, you can also use that setup.
We need more info... what broadband.. what modem.. what have you tried?
What is the current setup of the dlink? -
My iMac doesnt' see my Canon MP560 wi fi scanner ever since I created a wireless network in my house. Can't find a way to change whatever settings i need to to connect the scanner. help.
Well let's see if we can help you get set up. Have you got any 2.4 GHz cordless phones in the house and if so try unplugging them and do a hard reset of the express.
1. unplug the express
2. press the reset button
3. while pressing the reset button plug in the base station
4. keep holding the rest button till you see 4 green lights flash
you may have to hold it for 30 seconds or so
if this doesn't work try plugging the express in right beside the computer and then going through the airport setup assistant
Good luck
Let me know
iMac G5 iSight 17" Mac OS X (10.4.4) -
I just purchased the airport Express to use in hotels while traveling to create a wireless network from the hotels wired dsl. A friend said to set up the network from home prior to traveling. How do I set this up? Thanks.
In addition to RyanJC's comments, the 802.11n AirPort Express Base Station (AXn) can store up to five different http://docs.info.apple.com/article.html?artnum=108081 configuration profiles. You will need to use the AirPort Utility to create & save these profiles.
To create a new profile:
Open AirPort Utility, select your AX from the list, and then, click "Manual Setup."
From the AirPort Utility menu, select "Base Station," and then "Manage Profiles."
Click "+" to create a new profile; give it a name, and then, click OK.
Set options, such as network name, passwords, Internet connection method, etc.
When done setting the options, click Update.
To switch profiles:
Open the AirPort Utility, select your AX from the list, and then, click "Manual Setup."
From the AirPort Utility menu, select "Base Station," and then "Manage Profiles."
Click on the desired profile, and then, click OK to apply the new profile and restart the AX.
Just remember to switch to the desired configuration profile before removing power from the AX. -
Unable to create a wireless network with my airport express. Please help!
I am trying to setup a wireless network with an airport express, and connect to it with my Macbook. I just bought both of these and haven't been able to get wireless to work.
I initially plugged the ethernet cable from my cable modem into the airport express and plugged it into the wall. The macbook detected it when I opened airport utility, but the express had a flashing amber light and I was unable to connect. I then unplugged the express and re-started the cable modem. This time, the airport express showed a solid green light -which should mean that it is working correctly. However, the macbook did not find the airport express device when i searched for it using airport utility. I am able to connect the macbook directly to the cable modem, after re-starting the modem, and access the internet so at least some of the systems are go.
Any ideas? Thanks in advance for your help.
TomIs the issue that you cannot access the 802.11n AirPort Express Base Station (AXn) with the AirPort Utility that is running on your Win7 PC? ... or that once you have configured the AXn, the PC is unable either to find the new wireless network or can find it but cannot connect to it?
-
I want to create a wireless network for my iMac, Macbook Pro and iPad, and I'm confused about the Airport Extreme and Airport Express devices.
There is mention for both about connecting them to a DSL or Modem. Does this mean I have to obtain additional hardware before they will enable connection to the internet? (In the past, I've used a Belkin Router, which simply connected to the phone line.)
Any advice gratefully received.
TonyDoes this mean I have to obtain additional hardware before they will enable connection to the internet?
Yes, you need a modem. The AirPorts are routers only. They do not have a modem built in, so you will need a modem if you want to be able to connect to the Internet.
The Belkin device that you have used before is a modem/router. It combines the functions of a modem and router in one package. -
Using the iMac to create a wireless network. Is it possible?
At my college, we are not allowed to have routers. We can use switches that allow us to share the connection among many computers. I have a wired Intel iMac. I want to know if I use iMac to create a wireless network that way I can connect my Nintendo Wii and Nintendo DS.
It is not possible to do this, but this will solve your problem:
Wireless-G Linksys Access Point
Add High-Speed Wireless Access To Your existing Wired Network!
This is not a router, so you are probably allowed to use this. This will bridge your ethernet signal to a wireless signal.
Hopefully this is helpfull or solved your problem.
(please see the "helpfull" and "solved" button's above this message) -
Creating a wireless network using several Airport Express(es)
I would like to connect three AirPort expresses to my Sky Broadband router to create a new wifi network in my house. My router is in the basement and is connected into a hub which provides ethernet to the house. I would like to connect the AirPorts via ethernet to the router and create a single wifi network.
Can someone please tell me if this is possible and what settings the AirPorts should have. For instance, should I just extend the sky network using each AirPort or should I create a new network with one AirPort and then extend that with the others?
Many thanks
TerryIf each of the AirPort Express devices will be connected using Ethernet, you would configure them all exactly the same except for assigning different device names...AX1, AX2, AX3, etc.
Each Express will be configured to....
Create a wireless network
Same wireless network name on all devices
Same Radio Mode
Channel set at Automatic
Same wireless security setting
Same wireless network password
Very important....configure each Express in Bridge Mode
Post back if you need more details -
Network mode: Create a wireless network vs. Extend wireless network via ethernet
Can some one tell me the difference between configuring AirPort Utility : Network mode: Create a wireless network vs. Extend wireless network via ethernet? I connect my cable modem to my Airport Time Capsule to a network switch via ethernet. The switch contacts to three Airport Express (AE connects to two Apple TVs via Ethernet) and another TC. Which is the best mode to configure my network?
ThanksCreate a wireless network is used only when the Airports have an Ethernet connection. If you are using the setup wizard.....the setting will read Extend using Ethernet during the setup. If you go back in using AirPort Utility to check the Network Mode setting.....you will see that it is really Create a wireless network.
Extend a wireless network is used only if an AirPort is connecting to another AirPort using wireless.......not Ethernet.
Every one of the Airports on your network must be configured to Create a wireless network.
If you do connect an Ethernet cable to an AirPort that is already set up to Extend a wireless network......that will create a massive feedback loop that will crash the network until you remove the Ethernet connection to the device.
The bottom line here might be if you are using the setup wizard, it will make the correct choice for you.
Maybe you are looking for
-
Hi All, Please can somebody tell me how to configure LDAP Provider so that I can authenticate my ucm users via OpenLDAP 2.0.0.27 I tried my best to configure using the manual from oracle but this didn't help out and didn't work Please Help Thanks Raj
-
How do you transfer playlists from you ipod to your computer?
I am able to get my files on my computer, but now the playlists, any help?
-
How to findout how many instances are available in one server
how many instances are available in one server
-
I insert a cd and it looks like it is importing it just fine. After it is done and the cd is ejected the songs are not in iTunes. When I reinsert it for ripping it doesn't recognize that it has already done so. Please help! Thank you, Carl
-
How good is Elements 10 in making slideshows compared to, say, Pro Show Gold?
I have Photoshop CS4 and Premiere CS3 for photo and video creation, but was looking for a really good slide show program. Any thoughts? Someone recommended Elements 10. But internet sites don't even list it in their top 10.