Trying to get 2 computers on same network into a single game server
I can't seem to get 2 comps on my network in the same server on quake, I dunno if this has anything to do with IP or anything, but I was wondering if ther might be anything I can do to allow us both to play on the same server, I have a WRT54G Wireless G broadband router. Any information you can give me will be very appreciated. thank you
make sure that the router has the latest firmware...change the MTU size to 1400 and check whether it makes any difference....
Similar Messages
-
I am unable to charge my IPAD on the computer and it says not charging. Tried on 2 computers but same issue. Any Suggestions?
That's normal. Most USB ports dont' put out enough power to meet the iPad's requirements. (It says 'not charging' even though there is a trickle charge...it will charge over USB, but it'll take hours and hours)
Your iPad is best charged with the supplied charger plugged into the wall. -
Hi
While trying to perform the operation 'Annul All Below' in DRM 11.1.2.1, I received the following error: There was an error trying to get the status of the job. 1: The server returned an error processing CloseJob: Stack empty.
Has anyone seen this error before, and does anyone know what the fix is?
Thanks,Just giving my view on this.
When you try to restore a Version backup file, you get this error.
This is a known defect. The problem is caused by missing values in properties like AddedOn, AddedBy, which may occur when a version is copied with 'Clear Changed Properties' selected.
this is a known bug
but to workaround - Blend the affected version into a new, empty version, which will populate the 'ChangedOn' properties. You can then back up this version and it will restore.
Thanks,
~KKT~ -
How do you get two computers on same network for mirgration.
I am trying to migrate from an older iMac G5 running the most updated version of TIGER to our new MacBook Air running LION.
The air doesn't have a firewire connection, so it's trying to do it over the wireless network. I have them both on the same network, BUT the new Air is asking for me to update the Migration Assistant on the older machine. Don't have any idea how to do that.
Is there a work around?
Can I use USB connections?You need to install 10.5.8 on the PPC computer to work with Migration Assistant. It would be easier to clone the drive to an external hard drive. Then restore from the external hard drive using Migration Assistant.
-
How do I connect computers to same network?
I cannot figure out why my IMac and Macbook will not connect with each other so I can download files to my Macbook that was wiped out and is like a new computer. I'm trying to share files and internet and I'm unsure how to confirm that my computers are connected to the same network...what do I need to be sure to check? Thank you to anyone who understands this and can help!
Hi..
Help here > 3 Easy Ways to Share Files Between Macs -
Error trying to get LiveCycle ES up and running with JBoss/SQL Server
I am having an error trying to get LiveCycle ES Trial up and running with JBOSS and SQL Server. The LiveCycle ES and JBOSS engines are running on Windows Server 2003 SP #2 under VMWare Server with 2 vCPUs/1 GB vRAM. The SQL Server database is SQL 2005 x86-64 with SP #2 on a separate server.<br /><br />I have carefully followed all of the instructions for setting up jboss, modifying all of the appropriate XML files, downloading the SQL JDBC drivers and putting it in the %JBOSS_HOME%\server\all\lib directory, etc. I tried both the SQL JDBC 1.1 and 1.2 drivers and they both fail.<br /><br />The error I get is on startup of jboss using<br />cmd /c start /low run.bat -c all<br />(and yes I also just tried run.bat -c all)<br /><br />it runs along file until it gets here<br />2008-06-18 16:00:03,123 INFO [org.jboss.resource.connectionmanager.ConnectionFactoryBindingService] Bound ConnectionManager 'jboss.jca:service=DataSourceBinding,name=IDP_DS' to JNDI name 'java:IDP_DS'<br />2008-06-18 16:00:03,123 INFO [org.jboss.resource.connectionmanager.ConnectionFactoryBindingService] Bound ConnectionManager 'jboss.jca:service=DataSourceBinding,name=EDC_DS' to JNDI name 'java:EDC_DS'<br />2008-06-18 16:00:03,373 INFO [org.jboss.resource.connectionmanager.ConnectionFactoryBindingService] Bound ConnectionManager 'jboss.jca:service=ConnectionFactoryBinding,name=JmsXA' to JNDI name 'java:JmsXA'<br />2008-06-18 16:00:03,373 INFO [org.jboss.resource.connectionmanager.ConnectionFactoryBindingService] Bound ConnectionManager 'jboss.jca:service=ConnectionFactoryBinding,name=adobe_JmsQueueXA' to JNDI name 'java:adobe_JmsQueueXA'<br />2008-06-18 16:00:03,389 INFO [org.jboss.resource.connectionmanager.ConnectionFactoryBindingService] Bound ConnectionManager 'jboss.jca:service=ConnectionFactoryBinding,name=adobe_JmsTopicXA' to JNDI name 'java:adobe_JmsTopicXA'<br />2008-06-18 16:00:03,482 INFO [org.jboss.resource.connectionmanager.ConnectionFactoryBindingService] Bound ConnectionManager 'jboss.jca:service=DataSourceBinding,name=DefaultDS' to JNDI name 'java:DefaultDS'<br />2008-06-18 16:00:03,514 WARN [org.jboss.resource.connectionmanager.JBossManagedConnectionPool] Throwable while attempting to get a new connection: null<br />org.jboss.resource.JBossResourceException: Could not create connection; - nested throwable: (org.jboss.resource.JBossResourceException: Failed to register driver for: com.microsoft.jdbc.sqlserver.SQLServerDriver; - nested throwable: (java.lang.ClassNotFoundException: No ClassLoaders found for: com.microsoft.jdbc.sqlserver.SQLServerDriver))<br /> at org.jboss.resource.adapter.jdbc.local.LocalManagedConnectionFactory.createManagedConnecti on(LocalManagedConnectionFactory.java:164)<br />[ lots more error scrolls ]<br /><br />this repeats multiple times<br /><br />I can see that it does acknowledge that I put the sqljdbc.jar file in the appropriate directory from the boot.log<br /><br /><snip><br />15:59:44,856 DEBUG [SARDeployer] deployed classes for file:/C:/jboss/server/all/lib/sqljdbc.jar<br /><snip><br /><br />please help!
APJ<br />We ran into many issues setting up a very similar environment. In the end we had to use a specially configured JBoss, supplied by Adobe, to make a connection with the SQL database. Since you have SQL w/ SP2 on it, you will need the 1.2 driver for sure, but you may want to talk to Adobe support about obtaining the version of JBoss they supplied us with. The Adobe Support Reference Number is: 1-52422366.<br /><br />Even with the alternate JBoss we had to perform the following steps to get the configuration right:<br /><br />1. Install Livecycle from the installation DVD. Follow the instructions for installing LiveCycle supplied by Adobe, including all pre-installation instructions. Make sure NT service is installed with parameters, and dont run Configuration Manager.<br />2. Rename %LIVECYCLE_INSTALL%\jboss to %LIVECYCLE_INSTALL%\jboss_orig<br />3. Extract the zipped new, good instance of JBoss (supplied by Adobe) to the %LIVECYCLE_INSTALL%\ folder <br />4. Go to the %LiveCycle_Home%\deploy folder and make a copy of the file adobeimport_SQLServer.jar file. Rename the copy of the file to aadobeimport_SQLServer.jar. There seems to be a bug in configuration manager that looks for a file with the extra a appended to the beginning of the file name, where that file normally isnt there. Make sure that the adobeimport_SQLServer.jar file is still in this folder as well.<br />5. Edit the data source file (%JBOSS_HOME%\server\all\deploy\ adobe-ds.xml) to point to the correct database for the LiveCycle Server.<br />a. Update the <connection-url>, <user-name>, and <password> tags with the correct database connection information.<br />b. If BAM is to be used on the server (this should be done on the Production server) then delete both lines that state Remove this line, if BAM is used.<br />6. Go to the login configuration file (%JBOSS_HOME%\server\all\conf\login-config.xml), and edit the section labeled <application-policy name = "MSSQLDbRealm">.<br />a. Change the Principal, UserName, and Password options to point to the correct database. These will be the same as what was changed in the adobe-ds.xml file from the step above.<br /><br />7. Edit the system variables on the server. Add to the Path variable %JBOSS_HOME%\bin, and add the variable JBOSS_HOME with the path to the JBoss folder on the server. (D:\Adobe\LiveCycle8\jboss for example)<br />8. From windows services start the JBoss for Adobe LiveCycle ES v8.0 service. Review the JBoss server log (%JBOSS_HOME%\server\all\log\server.log) to verify that JBoss starts without throwing any exception errors (A document timeout exception is the only acceptable exception for starting the service). <br />9. Run the LiveCycle Configuration Manager (%LiveCycle_Home%\ConfigurationManager\bin\ConfigurationManager.bat). <br />a. Select to Not Upgrade fromLiveCycle 7.x.<br />b. Check all boxes on the Solution Component Selection screen.<br />c. For the Task Selection screen check all the boxes except for the Import LiveCycle ES Samples into LiveCycle ES if on the production server. <br />d. Run through the rest of the configuration manager interface to setup the LiveCycle server with the new application server. Follow the steps supplied by Adobe for this.<br />10. Once configuration manager has completed, reboot the server, and verify that JBoss starts up again without any exceptions or errors (again a document timeout exception is an acceptable exception. Look at the server log to verify this (%JBOSS_HOME%\server\all\log\server.log)).
-
We've got them authenticating/binding with AD (after hours of troubleshooting to get working), and their Home drive on the Windows 2003 server loads in the dock, but they also want to be able to load the same network shares on the server e.g. "Students$" for every student that logs onto the iMac. I realise without Lion server we can't control it by group, but if we could at least set it up consistently for the students that would be a great start.
Thanks.When you install you get the opportunity to install it for "All Users".
It sounds like you have a demo version on your Mac however, you need to delete it:
http://www.freeforum101.com/iworktipsntrick/viewtopic.php?t=105&mforum=iworktips ntrick
Peter -
Combine 2 Queries (from SAME table) into a SINGLE query
I have this two queries (from SAME table), and want to combine into one SINGLE query, how?
How can we use CASE WHEN THEN for such situation?
Query1:
SELECT t_inner.*,
Floor(t_inner.ProductiveTime/ 3600) || 'hr:' || LPAD(Floor(Mod(t_inner.ProductiveTime,3600) / 60),2,0) || 'min:' AS Productive_Time,
Floor(t_inner.OperatorDownTime/ 3600) || 'hr:' || LPAD(Floor(Mod(t_inner.OperatorDownTime,3600) / 60),2,0) || 'min:' AS OperatorDown_Time
FROM
(SELECT SYSTEMTYPE,
sum(TIME_TEST + TIME_STEP) AS ProductiveTime,
sum(TIME_IDLE) AS OperatorDownTime
FROM PFODS.PPL_TESTSYSTEMS_UTILISATION
WHERE (SYSTEMTYPE = '0005-072')
AND (TS_START >= to_date('13/01/2014', 'DD/MM/YYYY'))
AND TS_End <= to_date('17/01/2014', 'DD/MM/YYYY') + 1 + (1/1440) +(59/86400)
AND MONO != '9999999999'
GROUP BY SYSTEMTYPE ) t_inner
Query 2:
SELECT t_inner.*,
Floor(t_inner.MachineDownTime/ 3600) || 'hr ' || LPAD(Floor(Mod(t_inner.MachineDownTime,3600) / 60),2,0) || 'min' AS MachineDown_Time
FROM
(SELECT SYSTEMTYPE,
sum(TIME_IDLE) AS MachineDownTime
FROM PFODS.PPL_TESTSYSTEMS_UTILISATION
WHERE (SYSTEMTYPE = '0005-072')
AND (TS_START >= to_date('13/01/2014', 'DD/MM/YYYY'))
AND TS_End <= to_date('17/01/2014', 'DD/MM/YYYY') + 1 + (1/1440) +(59/86400)
AND MONO = '9999999999'
GROUP BY SYSTEMTYPE) t_inner
see http://postimg.org/image/koq87iyyz/ and
http://postimg.org/image/fv3zxa38nwith the first query,
SELECT t_inner.*,
Floor(t_inner.ProductiveTime/ 3600) || 'hr:' || LPAD(Floor(Mod(t_inner.ProductiveTime,3600) / 60),2,0) || 'min' AS Productive_Time
FROM
(SELECT SYSTEMTYPE,
--sum(TIME_TEST) AS TIME_TEST,
--sum(TIME_SYSTEM) AS TIME_SYSTEM,
--sum(TIME_STEP) AS TIME_STEP,
--sum(TIME_IDLE) AS TIME_IDLE,
sum(TIME_TEST + TIME_STEP) AS ProductiveTime
FROM PFODS.PPL_TESTSYSTEMS_UTILISATION
WHERE (SYSTEMTYPE = '0005-072')
AND (TS_START >= to_date('13/01/2014', 'DD/MM/YYYY'))
AND TS_End <= to_date('17/01/2014', 'DD/MM/YYYY') + 1 + (1/1440) +(59/86400)
AND MONO != '9999999999'
GROUP BY SYSTEMTYPE) t_inner
it gives output as from
http://postimg.org/image/koq87iyyz/
with the second query,
SELECT t_inner.*,
Floor(t_inner.MachineDownTime/ 3600) || 'hr ' || LPAD(Floor(Mod(t_inner.MachineDownTime,3600) / 60),2,0) || 'min' AS MachineDown_Time
FROM
(SELECT SYSTEMTYPE,
sum(TIME_IDLE) AS MachineDownTime
FROM PFODS.PPL_TESTSYSTEMS_UTILISATION
WHERE (SYSTEMTYPE = '0005-072')
AND (TS_START >= to_date('13/01/2014', 'DD/MM/YYYY'))
AND TS_End <= to_date('17/01/2014', 'DD/MM/YYYY') + 1 + (1/1440) +(59/86400)
AND MONO = '9999999999'
GROUP BY SYSTEMTYPE) t_inner
it gives output as from
http://postimg.org/image/fv3zxa38n/
I want to come those 2 queries into a single query, such that it gives both outputs as above. Let me know if you need any other information. thanks. -
Can't get homesharing to work between two computers on same network
we have been using homesharing for a long time and now all of a sudden homesharing isn't working. Turned it off on both computers and then turned it back on, but still doesn't work. What do I do now?
Have you tried restarting the router.
-
Itouch was reset to factory defaults. Have tried ideas listed in ITunes help. Any ideas?
Error 1 or -1
This may indicate a hardware issue with your device. Follow Troubleshooting security software issues, and restore your device on a different known-good computer. If the errors persist on another computer, the device may need service.
The" may need service' meand there is a hardware problem. In that case make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
Our iMac isn't loading a specific website (we get a message saying it can't connect to that specific server), regardless of browser (I've tried it in Chrome, Safari, and Firefox). However, the same website, which is for a major medical provider, loads without any issue on our other computers on the same wireless network. Is it an issue with the iMac's settings? All other websites seem to be loading without issue on the iMac.
... Is it an issue with the iMac's settings?
Possibly. Make sure you are not using a proxy server. Look in Safari Preferences > Advanced > Proxies > "Change Settings..." This will take you to the applicable Network Preferences. Make sure that nothing is selected in the "select a protocol to configure" list. It should look like this:
Still not working?
Locate your Terminal app. It is in your Utilities folder. Open Terminal.
In Terminal, copy (triple-click) and paste the following line:
osascript -e 'tell application "System Events" to get name of every login item'
This will produce a list of all your account login items.
While you are in Terminal, copy (triple-click) and paste the following line:
kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}'
This will produce a list of all non-Apple kernel extensions. There will be few, if any.
Post the results of the above. -
Convert multiple lines for same material into a single line in Sales Order
Our company has a requirement, they want if there are multiple lines exist for the same material in sales order and purchase order then it should become like one single line.
10 35712 5pcs
20 100885 10 pcs
30 35712 10pcs
Now our requirement is that should become a single line like this
10 35712 15pcs.
I will Text Removed.
Regards,
Khawar
Message was edited by: G Lakshmipathi
Please dont add such text in your postNow our requirement is that should become a single line like this
Where? Meanwhile, I hope, you would have searched in SCN / Google before posting as it is a basic question and needs to be locked. If searched, specify clearly what efforts you took to find out solution to your requirement.
G. Lakshmipathi -
Multiple clients with same account on a single IMAP server
Hi,
I am connecting to a IMAP server using same account but from 2 different machines. From one machine a mark a message as SEEN=FALSE. But on the second machine, the flag will still be TRUE.
Is there any way to co-ordinate between multiple clients so that all the clients are in sync.
Regards,
Nitin.I was able to resolve the problem using addMessageCountListener and messagesAdded method, as suggested by you.
I am now facing another problem. Whenever a new message is received, code inside messagesAdded method gets executed. Here I am trying to spawn another thread and do some stuff. But this new thread is not starting at all. It goes into some JavaMail:EventQueue and does nothing. What is the concept of EventQueue here? How can I get this new thread executed?
Also will there be synchronization problems in messagesAdded method. Say I received a message and I am processing it in the messagesAdded method. In the mean time another message comes up. How will this behave. -
Old airport base not on same network
Hello,
I set-up TC and my Airport Express easely
Now after shutting down, and resetting my old Airport base
it does get on the same network, it created its own network called Apple Network aa95...
How do I get this Airport Base to join my network composed of TC and A Express ?
ThanksFinally made it
Reset AEB (UFO style) about 5 times,
Airport Utility needs enhancements rapidely -
I have two servers. One is for databases (DB) with the mail server configured and the other is for SSIS without mail server. Both servers are in the same network. On the SSIS server the SSIS package exports data from the DB server table
to xls file. The file is saved in SSIS server. When I created a task to send the email (using sp_send_dbmail) to attach that file, I got the error message:
Error: Executing the query "EXECUTE [msdb].[dbo].[sp_send_dbmail]
@profile_na..." failed with the following error: "Attachment file H:\test.xls is invalid.".
Any help will be appreciated. Thanks.
A Fan of SSIS, SSRS and SSASWhere are you running this?
If its in the other server (DB) you need to use UNC path to the SSIS server folder where file resides
Also the executing account should have access to the folder as well as the file. So If you're running this from a job make sure you either provider folder and file access to sql agent job service account or create a separate proxy account with the required
permissions and configure the job to use the account
see
http://www.databasejournal.com/features/mssql/article.php/3789881/Proxy-Accounts-in-SQL-Server.htm
http://www.codeproject.com/Articles/28918/SQL-Server-Agent-Proxy
Please Mark This As Answer if it solved your issue
Please Vote This As Helpful if it helps to solve your issue
Visakh
My Wiki User Page
My MSDN Page
My Personal Blog
My Facebook Page
Maybe you are looking for
-
Every time I open lightroom I get a pop up message saying "Lightroom encountered an error when reading from its preview cache and needs to quit" and it closes. Ive already tried reinstalling, nothing seems to work. Help please!
-
HI, Please tell me how I can use my ipod touch, using the selected playlist and have each song stop after it ends before going to the next? I'm a dancer, so it's hard to dj and dance at the same time. I don't want to hit pause! Thank You, Natasha
-
(BI 7.0) Debugging Routines in Transformation
Dear All, I would like to debug my own ABAP routine in the transformation for BI 7.0, anyone know how to set a break-point somewhere for popping up the debugging window? thanks B.R Charlie
-
Hello, I am trying to connect Sharepoint as Content Server in SAP. I have already read about a third party product from E.link to be able to do this. I also read about Duet. I dont know if Duet allows this integration. Another option I have read is t
-
You already have a schema opened on this file with another name: abc
I am trying to create a model for an XML file, when I clicked on "Objects to Reverse" checkbox under "Selective Reverse" tab, I am getting the following error: java.sql.SQLException: You already have a schema opened on this file with another name: ab