Trying to install 2 - Aironet 1300 Bridges... major problems

I set up both ends of this bridge (about 1 mile apart) and I get an association, so I think I'm golden... well, I haven't been able to get the web gui ping/link test to work at all across them, so I upgraded to the 12.4 IOS on the main site, then went to the far-end site to upgrade that one and now I can't even bring up the web gui... I can ping it from the CLI of the switch, but not from the laptop I have connected via CAT5 to the switch... any suggestions?
Did upgrading the IOS cause this somehow????

Have you tried to telnet or console to the bridge and verify your configuration? You might need to write erase the config and re-configure the box. Can you post your configs?
Do you have clear line of site? Are you using the internal antenna model, or external antenna model?
Make sure that your config says: ip http server
Seth

Similar Messages

  • Security on Aironet 1300 bridges

    I am a newbie on this fourm. I required your suggestions and recommendations. I have aironet 1300 bridges. I want to connect them in point to multipoint envt.
    I want to have one root bridge and rest as non root bridges. But i want to implement authentication of non-root bridges through root bridge. Please suggest what is the latest and strongest authentication and security protocols that i can use. Please i am looking for an early response.

    EAP Authentication type provides the highest level of security for your wireless network. By using the Extensible Authentication Protocol (EAP) to interact with an EAP-compatible RADIUS server, the root access point/bridge helps another access point/bridge and the RADIUS server to perform mutual authentication and derive a dynamic unicast WEP key. The RADIUS server sends the WEP key to the root access point/bridge, which uses it for all unicast data signals that it sends to or receives from the non-root access point/bridge. The root access point/bridge also encrypts its broadcast WEP key (entered in the access point/bridge's WEP key slot 1) with the non-root access point/bridge's unicast key and sends it to the non-root access point/bridge.

  • Need help on Aironet 1300 bridges

    Greeting,
    We have just upgraded two Aironet 1300 bridges (from cisco 350) on two buildings about 100 yards apart. They are only running as bridges. One is set up as root bridge and another one is setup as non-root bridge. Root bridge is in the main building direct connect to Cat 4506. For some reason the root bridge has some intermittant problem connect to the network. We are running the IOS 12.3(8). We changed the cable but the problem still occured. Everytime we have to reboot the root bridge in order to get it back. but all the interfaces in the root bridge show " up / up" prior to reload. The "show tech" looks fine on the root bridge. Any suggestion? Shall I change root bridge to workgroup bridge?
    really appreciate for any helps,
    Gene

    Hi Steprodr,
    I just need to clearify that the power injector is on the non-root bridge? I think the power are fine on both bridges when the problem occured. We used cisco 350 bridges before the upgrade. So the cable and port are still remain the same. The problem is more going towards from root bridge come back to Cat 4506 because both root and non root bridges can ping each other when the problem occured.
    thanks,
    Gene

  • I am trying to install SC6 Photoshop and Bridge on a new Mac laptop.  Though I have the software the laptop doesnot have a disk drive so I copied it from my desktop and transferred it via a portable hard drive.  I get a message:  Configuration error. Peas

    I am trying to install SC6 Photoshop and Bridge on a new Mac laptop.  Though I have the software the laptop doesnot have a disk drive so I copied it from my desktop and transferred it via a portable hard drive.  I get a message:  Configuration error. Please uninstall and reintall...   Error 16

    Hi midtone,
    Is it possible to download the product? It seems that copying didn't work.
    If you can download then please use this link: Download CS6 products
    -Ankit

  • I get an error message when trying to install software update 4.2.8 "problem downloading, network connection timed out. Check network connections.

    I get an error message when trying to install software update 4.2.8
    "problem downloading, network connection timed out. Check network connections."
    Anyone one else had this problem?

    Brian-KK Sabah wrote:
    I too get the same message but I the software had downloaded 100% but about half way through "processing file" the error message (.3259) Check network connections. How do I fix this?
    See Here for your Error Message -3259
    http://support.apple.com/kb/ts2799

  • Hi. I can install Adobe Flash Player plugin as i usualy did since 5 years. The problem is that firefox is always asking fo it if i i had never install it. I've tried to install firefox newer versions and the problem pesists. Thanks.

    Hi. I can install Adobe Flash Player plugin as i usualy did since 5 years. The problem is that firefox is always asking fo it if i i had never install it. I've tried to install firefox newer versions and the problem pesists. Thanks.

    Hi, glad that worked for you. Also thanks for the explanation as how you came about this. Yes, from my understanding any Install of the CS5, even a trial version Installs the 10.1 (beta/prerelease) versions. It is not clear to me or others why the 10.1 was used in the CS5 instead of the latest version (10.0.45.2). My only guess is that the 10.1 is very close to being released as a shipping version (final release) to the public. The 10.1 had a target date of the first half of 2010. Perhaps that was the reasoning. This is just my opinion:-)
    As I said, many users are having this problem, not just with the CS5, but they Install the 10.1 thinking that will solve whatever problem they may be having with the latest version.
    Your thread is very helpful for other users that may be having the exact problem that you were. For this reason if you marked your thread as answered, they would read it first.
    Thanks,
    eidnolb

  • Aironet 1300 Bridge and AP simultaneously

    Hello Everybody I`ll like to use the Aironet 1300 in a Bridge and AP operation simultaneously and I`ll use a Omnidirectional Antenna ANT-2506 to cover clientes. The question is if in this design the non root AP/bridge operate like repeaters and what about the Bandwith. does this anntena work for a AP application? What is the coverage with this anntena for clients and others bridges.
    My scenario is a Root 1300 with Antenna ANT-2506 for clients and bridges and 5 1300 (non root) with Antenna ANT-2506 for clients and bridges.
    Thanks in advance!

    The flexibility of the Cisco Aironet 1300 Series allows it to operate asa wireless bridge, access point, or a workgroup bridge.
    http://www.cisco.com/en/US/products/ps5861/products_configuration_guide_chapter09186a00804158b6.html

  • Aironet 1300 Bridges

    I have a question on Point-to-Multipoint Bridging for aironet 1300's.
    Here is the setup that I have:
    I have three mobile units that I need to connect to eachother.
    Each unit has a 1300 series bridge in it, one set as a root, the other 2 as non-root.
    The computers that are in each unit are setup in a Workgroup, there are 6 computers in each unit.
    Can anyone give me an configuration example or point me to an page for a point-to-multipoint setup for the Bridges? I can find point-to-point but nothing else. Or is that the same setup, just worded differently?
    thanks
    --Jon

    Hi,
    Q1 >> two must be non-root and one a root bridge? For the three units to talk  to each other, does there have to be any specific settings or not?
    ANS >> NO. We need to make sure the configuration is exactly same on all the 3 devices, only difference is the station role.. that is..
    on the ROOT bridge the radio station role should be "Root bridge"
    on the Non-ROOT 1 bridge the radio station role should be "Non-Root bridge"
    on the Non-ROOT 2 bridge the radio station role should be "Non-Root bridge"
    Q2 >> Also, I will not have any internet connections or functionallity, they  will be unit to unit communications only. Will this create a problem in  the root bridge then?
    ANS - NO, there will not be any issue in the Root bridge.. the traffic will flow between the bridges without any problem.
    lemme know if this answered your question..
    Regards
    Surendra
    ====
    Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

  • Throughput on Aironet 1300 bridges

    I have a pair of 1300 series Aironet bridges that I use to connect two buildings approximately 3/4 of a mile apart.  The line of sight is completely clear.  In my logs I keep getting these messages repeatedly:
    %DOT11-4-TKIP_MIC_FAILURE: TKIP Michael MIC failure was detected on a packet (TSC=0x0) received from 0022.55c2.7b90
    Eventually the two bridges stop communicating and I then reload the radio interface on the root bridge to get packets flowing again.  I am looking for an explanation of the above message.  I've done some reading that suggests there could be an attack on the network that would cause this, but based on my location I find this to be very, very unlikely.  I tried changing the encryption method from TKIP to AES CCM.  That got rid of the above error, but my throughput came crashing down to a crawl.  When changing encryption methods is there something else I need to change in order to free up traffic between the two bridges?  Why would the encryption method change the throughput of traffic?
    Thanks for any help you can provide.

    If you are using the first 12.4 aIOS versions then please perform upgrade, those versions reported ALOT I REALLY MEAN ALOT OF WEIRD ISSUES while bridginng... on the other hannd dued, that log just means that the CKIp is failing either attack and 90% of the times I had this issues onn TAC was interferennce...

  • Warning on Event Log of Aironet 1300 Bridge

    I've been getting warning messages from the event log of a 1300 series bridge, which is set as an Access Point in the network, states: 'Packet to client (mac address) reached max retries, removing the client';  I'm not sure why the client is removed.  Does 'reached max retries' mean that the client has tried to many times to connect to the AP/Bridge?  What are other possible reasons why? 

    It means the AP has attempted to send a packet to the client and has not received an ack from it. The AP assumes the client is no longer in range of it and disconnects it.
    Sent from Cisco Technical Support iPad App

  • Trying to migrate to a new computer - major problems

    Hi, I'm posting this for my friend Cindy who is trying to migrate from an old laptop to a new PC. Laptop: Vista PC: Windows 7, both 64 bit.
    She called me after moving some files around and being partially successful. The problem is that a few thousand photos are missing and cannot be found. I've searched her internal and external hard drives and cannot locate the files on either computer. I do believe they are gone.
    What we're trying to figure out is this: How can she take everything that is on her laptop and migrate it properly to the PC. The catch here is that the laptop is messed up too because of trying to move things around.
    So, is there any way to get PS Lightroom to scan the catalog and then search the whole computer (c: and g: drives) for the missing files, and then export them into a new catalog that is properly organized? I realize that's a tall order but we are grasping at straws here.
    Thanks for your time, and feel free to point me in the right direction rather than answer the questions explicitly.
    Ryan (via Cindy's account)

    You need to supply more information:
    1) What version of LR is installed on the old laptop, and what version on the new desktop?
    2) Are the "few thousand missing photos" showing up in LR on the new desktop, but with '?' symbol in the thumbnails? If so double-click the '?' to display the laptop file location path where LR thinks the files are.
    3) What is the 'G:' drive letter (external drive?) and has anything been deleted from the G: or C: drives?
    4) Was there more than one (1) Lightroom catalog created on the laptop? If so where were the catalogs saved?
    This link will be helpful in locating LR files and folders:
    http://kb2.adobe.com/cps/843/cpsid_84313.html
    Do NOT open any applications on the laptop other than Windows File Explorer, to prevent overwriting any possibly deleted files.

  • Aironet 1300 Ethernet seems down

    Hi,
    We've installed an Aironet 1300 (with external antenna) at the top of an 80 foot mast. Before installation we configured it with a static IP, setup its SSID etc etc. We also tested connecting to another WAP etc. All setup was done using its web interface.
    However we cannot access it using the ethernet port on the power injector. If I connect using the console port I can see that it is running, however during initialization it says that it can't bring up the FastEthernet port.
    If I do 'show ip interface brief' then it lists the IP address against BVI, but says the ethernet port is down. We've tried a different power injector with the same result.
    Does anyone have any idea what we're doing wrong? We've had no similar problems with the other 20+ Aironet's we've installed.
    Thanks
    Richard Cronin

    Hi Richard,
    What I have observed is that if nothing is connected on the ethernet interface, while initializing it always throws this error.
    As you mentioned that the you are not able to access the bridge ethernet connection is down and this seems to be the reason why you are getting this error.
    Now coming to the point please crosscheck if the connection is done as -
    1. Plug a Category-5 Ethernet cable into the port on the power injector labeled 10/100Base Tx to Device.
    2. Plug the other end of the Ethernet cable into the Ethernet Port on the access point or bridge.
    3. Plug a Category-5 Ethernet cable into the port on the power injector labeled 10/100 Base Tx to Network.
    4. Plug the other end of the Ethernet cable into your 10/100 Ethernet switch, hub, or network.
    5. Connect a suitable 48-VDC power source to the power receptacle labeled DC48V
    I am sure that you must have done the connectivity as above but just to cross check. Just cjeck for TX to device/network
    Also note that the overall span can not be more than 200mts. 100 per segment.
    -> Sushil

  • Cisco Aironet 1300 QoS

    Hello, I have 2 Cisco Aironet 1300 Bridges which provide data and voice communication between 2 buildings. Up until recently QoS has not been needed, but lately there appears to be congestion due to reports of poor voice quality. Building A houses a V3000 NBX Telephone system, Building B houses approximately 30 remote IP phones. Building A and Building B are approximately 100 yards apart. No VLAN's. Due to myself being an extreme noob to Cisco bridges, I was hoping some of you may have had experience in setting this up and hopefully provide some tips. I need to prioritize traffic on UDP ports 2093-2096 and TCP port 1040. Thank you in advance for any suggestions. My current running config is below:
    Using 1283 out of 32768 bytes
    version 12.3
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname LHS-WeightRoom-WCV
    ip subnet-zero
    aaa new-model
    aaa authentication login default local
    aaa authorization exec default local
    aaa session-id common
    dot11 ssid wcv
    authentication open
    guest-mode
    dot11 ssid wcvcisco
    authentication open
    infrastructure-ssid optional
    username root privilege 15 password 7 0247335A05320A2244
    username Cisco privilege 15 password 7 074E164D403D1C061F
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    ssid wcv
    ssid wcvcisco
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
    54.0
    station-role root bridge
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    bridge-group 1
    bridge-group 1 spanning-disabled
    hold-queue 80 in
    interface BVI1
    ip address 10.141.8.6 255.255.254.0
    no ip route-cache
    ip default-gateway 10.141.8.5
    ip http server
    ip http authentication aaa
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    control-plane
    bridge 1 route ip
    line con 0
    line vty 0 4
    end

    Here is the URL for the configuration of Cisco Aironet 1300 QoS. Follow the guide it may help you
    http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.3_4_JA/configuration/guide/o13qos.html

  • Aironet 350 configuration to Aironet 1300

    Is it possible to download an ini configuration from an Aironet 350 bridge, convert it and upload it to an Aironet 1300 bridge?

    Nevermind...I found it http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/s12213JA.html#wp55027

  • Aironet 1300 Point to Point not Communicating

    Hi,
    I am trying to set up (2) 1300 bridges, but I can not get them to talk to eachother. They currently have no external antennas connected, and are about 50ft apart (for setup/configuration purposes). Is there any where to find a document that shows how to set them up w/o a radius server or leap configurations. I'm really looking to just get them to talk to eachother first and formost. Thanks for any help.

    Hi,
    I guess that you must be referring to this document:
    http://www.cisco.com/en/US/tech/tk722/tk809/tech_configuration_examples_list.html
    The main thing is to configure the same SSID, with the same security settings, on both the root and non-root. So you can use the Web interface, no VLAN, one radio.
    1. Go to express security, on the Web interface, and create an SSID, with no security. Do the same on both access points.
    2. Go to the AP radios, set one AP to root bridge, the second to non root bridge, enable the radios, it should work...

Maybe you are looking for