Trying to output HDCAM...

So i have several QT clips that were shot with various frame rates....ranging from 24 to 60 frames. Some were shot using DVCPRO HD 720p 60i (see below):
1. DVCPRO HD 720p60, 960X720 23.98 fps
2. DV 720X480 29.97 fps
3. DVCPRO HD 720p60, 960X720 59.94 fps
I have built a sequence using the DVCPRO HD 720p 30 in FCP. Using Media Manager.....could i theoretically output this to APPLE PRO RES 422(HQ) 1920 X 1080i 30p to HDCAM? Keep in mind i am only using FCP 6.0.2 with no additional hardware. We are trying to build 1 QT to have a post house output to HDCAM. Hopefully we are doing this correctly.

NO need to transcode to anything. Just export out a self contained QT file, take that to a post facility with a Kona 3 card, and they can output your 720p 23.98 to 1080p 23.98 HDCAM, upconverting on the fly thru the card.
I have done this many a time.
Shane

Similar Messages

I am trying to output a PDF gallery from CS6 bridge in 10.8.5 on a Mac.

I am trying to output a PDF gallery from CS6 bridge in 10.8.5 on a Mac. No options are available from the pull-down Output arrow.

Hello,
Although not as simple as it should be you can use a program like "Grab" to take a screenshot of the frame in the preview window in iMovie.
http://support.apple.com/en-us/HT201361
Hope This Helps,
Ryan (BURNINGJUNK)

I'm getting an error - VxD NIPALK(01) when trying to output a 5 second tone through LabVIEW and AO...a 2 second tone is no problem.

I'm using LabVIEW 6i, Windows 98, and a PCI-MIO-16E-4 board which is supported only by earlier versions of NIDAQ. Any suggestions?

Hello;
To give you better advise I would need more details about the signals you are trying to output to the analog channel of your DAQ board; such as update rate, frequency of the signal, number of channels, etc.
Regards
Filipe

Trying to output to a Samsung 40" LCD TV correctly.

Problem:
I have hooked my macbook up to my Sony 40" LCD TV model LN-S4041D via an apple (Mini-DVI to DVI adapter) and then a (DVI to HDMI cable). My TV does not have a DVI input just HDMI and all of the other analog inputs. When I hook it up my i get an output on the screen but it is not mapping pixel by pixel to the TV's exact resolution. This is causing there to be a black bar all the way around about 2" wide (top, bottom, left and right). The tv's native resolution PC is (1360x768). Is there any way I can get the macbook to output this correctly. I have tried using DisplayConfigX and creating a custom resolution and when I try using that resolution my TV doesn't work at all. It can't find an appropriate signal from the macbook. I am building a Home Theatre PC and am planning on using a mac-mini or ITV when it is released but I would like to use my macbook in the meantime. Please Help!!!!

You should also consider posting your question to the AVS Forum (avsforum.com). You will likely find more people over there with info about this TV, even though they may own PCs and not Macs. The important thing to find out is if anyone, using any computer, has been able to get bit-for-bit working with that Sony. A lot of Sony LCD TVs have video processors that interfere with the ability of a computer to display on the TV at native resolution. Hopefully you won't encounter that.

Trying to output from s-video to composite (for television) radeon 4770

I put together a little htpc using a bunch of spare parts I had lying around...I'm trying to get the s-video to output to component in (RCA type connectors) I have the s-video to component adapter, but I have no idea what the color coding means, as well, I'm trying to figure out what, if anything needs to be configured software wise in order to have output to a television...790gx, athlon x2 5000+, radeon 4770, 2 gigs ram, windows 7 rc (didn't want to spend on as os right away), thanks for any help with this project.

Quote from: theubersmurf on 06-August-09, 08:57:14
title should actually say composite, sorry.
Topic title edited for you.
You can always click the Modify link above your post to make edits.
Quote
I have the s-video to component adapter, but I have no idea what the color coding means
You mean something like this?

Trying to Output Sound to Speakers and TV Simultaneously on H8-1360t

Hi everyone -
I have an HP H8-1360t with an AMD HD 7570 video card, running Windows 7 64-bit. I have speakers hooked up to the on-board sound via a standard 3.5mm cable. I run DVI to my monitor and HDMI to my TV. I am trying to get sound to go to the speakers and the TV simultaneously, without having to keep swapping the default playback device. I tried the following that I found online:
Open Sound panel
Select Speakers as the default playback device
Go to the "Recording" tab
Right click and enable "Show Disabled Devices"
A recording device called "Wave Out Mix", "Mono Mix" or "Stereo Mix" (this was my case) should appear
Right click on the new device and click "Enable"
Right click on the new device and click "Set as Default Device"
Double click on the new device to open the Properties window
Go to the "Listen" tab
Click on the "Listen to this device" checkbox
Select your HDMI device from the "Playback through this device" list
This worked the first time I tried it and I was getting audio through both the PC speakers and from the TV. Since then, it no longer works and I am only get audio via one or the other, depending on what device I select as my default. It's more of an annoyance than anything else - having to manually switch between output devices every time I want to watch something on my TV instead of my monitor. I assumed I could get dual audio output and simply not turn on the PC speakers when I wanted to watch something on the TV and it worked the first time! I don't understand why it is no longer working. Thoughts?
TIA!

Thanks for the reply!
I believe that the answer is answer is yes to both questions - it defintely worked the first time. I'm not sure if I tried it on the first reboot or not but it did not work the next time I tried it. As far as what may have changed - I have no clue?!? I do not see that the 7570 or the Beats audio had any updates. According to Device Manager, I am running the latest IDT High Definition Audio CODEC driver.
i did notice a couple of things tonight. The video I used as a test the other day, that had audio and video going simultaneously on both displays, is displaying video on both the monitor and TV today but no audio on the TV. That said, when I open up the Sound control panel, and click on the AMD HDMI Output, right-click, and click "test", I do get test "beeps" through my TV (while the audio from my video is running through my PC speakers). So, it appears that it is indeed capable of outputting sound to both the PC speakers (via the onboard sound) and the TV (via the HDMI) - just not the same sound anymore! Another thing I noticed is that when I go to the Recording tab, the Stereo Mix selection is noted as the Default Device, and I can watch the "meter" on the right move up and down in sync with the volume of the video I am playing back - only there is no sound via the TV.
As usual, when I switch to the HDMI Audio Output as the Default Device, the sound plays fine on my TV.
This is strange...

Trying to output Quicktime movies from shake scripts only geting iffs

I am trying to batch render shake scripts using Qmaster. My quickcluster is working fine except I am getting individual iffs instead of a single Quicktime movie. My fileout node is set to Quicktime output. What I am missing?
Thanks.
Dan

Thanks for the fast reply. I checked my file out nodes and all of them end with .mov
For example: New Teaser (Shake) New Teaser Siren 1_2.mov
When I submit a batch, Qmaster creates individual iffs and also three scripts each with the proper filename, but no Quicktime movie
[file_name].shk-cleanupqt.shk
[file_name].shk-breakdownqt.shk
[file_name].shk-assembleqt.shk

Need VI design help, trying to output continuous voltage

This is one of my first attempts at this, so please bear with my elementary level questions.
I'm running LV 8.2.
Using the NI USB 6211 Multifunction I/O
My VI seems to work with the exception of a couple issues I'm not sure how to resolve.
1) I would like to turn on my voltage output (2v) on a true condition and have it stay on until the condition changes. When the condition changes to false, the output should turn off and stay off until the condition changes once again. Currently, when the loop is true the output turns on, but turns back off before the while loop iteration completes. So I end up with a on then off at the speed of the loop. How is this corrected??
2) I would like the indicator lamps on the front panel to be on only when the respective output is on.
Please have a look, any and all comments are appreciated.
Thanks in advance, Bryan
Attachments:
Hunley MR Damper Control.vi ‏933 KB

Thanks for the reply centerbolt,
I tried somthing like you proposed, only I used a mean value from the mathmatic functions pallet. This does change the output to a single floating point value. However, I still have the same palsing response.
Your correct, I am collecting a accelerometer value from a vehicle application. This measures roll acceleration. If the value is more than .2g it should activate the 2v output to fire a damper for the appropriate side of the vehicle and maintain the 2v until the condition changes. If the value is less than -.2, the other side damper should fire and stay on until the accel changes condition. But it doesn't maintain the output signal. Instead it cycles on then off every loop iteration.
I also have to figure out hoe to have my indicator light come on only if the respective damper is active.
Thanks again for any help, it is appreciated,
Bryan
Here's what I have at this point:
Attachments:
Hunley MR Damper Control.vi ‏953 KB

Trying to output 16:9 but it comes out as 4:3

Hi,
I recently switched from shooting 4:3 to 16:9, but when I export the sequence as a QuickTime movie it keeps reverting it back to 4:3 which squashes everything. That is, when I check the file by playing it through the QuickTime player, its displayed in 4:3.
Have I just got some settings wrong or have I messed it up somewhere down the line? I've checked that I have the easy set up as anamorphic, all the clips have the anamorphic tick by them and the sequence does too. The canvas is 16:9 in the edit and I cannot figure out, why when I play the completed file back does it come out 4:3.
Please help
Patrick

Hi, sorry for the slow reply...
I'm not sure where to find the specifications you asked for. I do have another question however.
When I set the easy setup to DV-PAL, in the easy setup window where it tells you the specifications, it says the output is 720x576. When I switch to DV-PAL Anamorphic, it still says in the specifications that the output is 720x576. Should it not switch to 1024x576 to make it anamorphic?
When I've exported movies from the timeline (when everything is set to anamorphic), and played them back in quicktime, the 'inspector' tells me that they're "720x576 (1024x576)". I don't understand why the 1024x576 is in brackets and it doesn't display them as such.
I hope that this makes sense and I've given you enough information to work with. If you can help me I' be very grateful!
Patrick

Organizer locks up while trying to output slideshow to a .mwv file...what can I do?

If I reload Elements will I loose my slideshow that is complete except for output to a .mwv file?

Photoshop does not have the Organizer it has the Bridge you should use the Photoshop Elements forum

IMac display issues / Trying to output at 1920x1080 through VGA

I'm having some external display issues with my 2007 Intel Core 2 Duo iMac (2.4ghz). Using the mini-DVI to VGA adapter, I plugged the VGA cable into a Samsung LCD TV (PC mode). When I originally had everything set up, I was using the TV as an extended display, with a display setting of 1920x1080.
However, I had to get a 25 foot VGA extension cable, and now my maximum resolution is 1600x1200. Does anyone know why extending the VGA cable would do this?

There could be any number of factors involved, but cheap cabling, or that your Mac does not have enough power to push the high quality resolution signal that distance first come to mind.
Dah•veed

I am trying to Output query through form variables .....

<cfquery name="cr" datasource="#session.db#" maxrows="10">
SELECT #form.collist# FROM #session.tn#
</cfquery>
<cfoutput>
<strong>SELECT</strong> #form.collist# <strong>FROM</strong> #session.tn#
</cfoutput>
<cfdump var="#cr#">
<cfset strList=#collist#>
<cfloop index="index" list="#strList#" delimiters="#chr(13)##chr(11)#">
<cfset total = ListLen(strList)>
</cfloop>
<table align="center" border="1">
<tr>
<cfloop index="z" from="1" to="#total#">
<td><cfoutput>#trim(listGetAt('#index#',Z,','))#</cfoutput></td>
</cfloop>
</tr>
<cfoutput query = "cr">
<tr>
<td>what shoud I use your to display query</td>
</tr>
</cfoutput>
</table>

Here is a quick sample that might help you.
<cfset colList="name,email" />
<cfset tableName="users" />
<cfquery name="report" datasource="mydsn">
     SELECT #colList# FROM #tableName#
</cfquery>
<html>
<head>
     <title>Report</title>
</head>
<body>
<table border="1" cellpadding="2">
     <thead>
          <tr>
          <cfoutput><cfloop list="#colList#" index="colItem"><th>#HtmlEditFormat(colItem)#</th></cfloop></cfoutput>
          </tr>
     </thead>
     <tbody>
     <cfoutput query="report">
          <tr>
               <cfloop list="#colList#" index="colItem">
                    <td>#HtmlEditFormat(report[colItem][report.currentRow])#</td> 
               </cfloop>
          </tr>
     </cfoutput>
     </tbody>
</table>
</body>
</html>

Trying to output to a file

When I run the below I receive an error
select * from professionals queryout 'q:\prof.txt'
Msg 102, Level 15, State 1, Line 1
Incorrect syntax near 'q:\prof.txt'.

If you have xp_cmdshell enabled you are ready to export your files:
EXEC xp_cmdshell 'bcp "select * from professionals" queryout "q:\prof.txt" -T -c -t,'
More details:
http://www.mssqltips.com/sqlservertip/1633/simple-way-to-export-sql-server-data-to-text-files/
If this post answers your query, please click "Mark As Answer" or "Vote as Helpful".

Trying to output best quality video for later work on a PC?

I have a video file that was sent to me to work on, add effects to, then send back to a customer for him to incorporate into a larger video project.
I have finished my work, but am wondering what settings I should use in Compressor to maintain the best quality file that will be easily readable by PC editing software (such as Premiere)
Please, any suggestions?

The best solution is to ask to talk to the guy with the PC and ask him what he needs. Hopefully he has some clue as to what he is doing and will give you direct answer. If he doesn't know what he is doing the first question you need to ask is he working in HD or SD? Start there.
Basically you really need to talk to the other editor. If you don't then you are just wasting everyone's time.

Trying to output a lot of records:

I've got trickey problem, I have a user that gets sent a number of files each week, these need to be compared.
As an example file1 and file2 are sent from an external source on disk. These files are in a text format and both contain email addresses. One of the files normally contains approx 600k email address records, where as the other normally contains approx 40k email address records.
There needs to be a comparison between these which I have done by creating 2 tables and using sqlldr to get the data in.
I then run a script like this:
select email_address
from file1
where email_address not in (select email_address from file2);
The problem in when I try to get these results out it takes an age... TOAD has never completed and using spool in sqlplus takes forever - infact I had a look at the expected runtime in Enterprise Manager and it said something like 336 hours...
Is there a better way to:
a) Compare the data in these files.
b) Get this data back out to a text file (csv file) for use by the user.
Is there any benefit to be had from using the 9i functionality of an external table?

Brilliant thank you.
select email_address from file1 f1 --643618-
where not exists (select email_address
from file2 f2
where f2.email_address = f1.email_address);
Works like a rocket!

Trying to output HDCAM...

Similar Messages

Maybe you are looking for