Trying to pass internet with a Cisco ASA 5505

Hello,
   I have not been having much success configuring my 5505 for Internet access, and I'm sure there are a few small things I'm missing.  At times I believe I got it to the point where I could ping, but still not pass through the Internet traffic.  At this point, I reset the 5505 and only changed a couple of settings. 
I have an external range with these characteristics: Network Address 67.139.113.16 (.17 is Gateway), SM: 255.255.255.248, available IP: 67.139.113.218
The external connection is through a T1 modem, and when I put those settings in my laptop, I can access just fine.
When I went through the startup wizard in the ADSM, I maded the internal interface 10.209.0.3, subnet mask: 255.255.255.0
I selected PAT in the Wizard, but don't know if I should have, or if the NAT rules I tried to put in are fine.
Eventually I want to add a Site to Site VPN to the rest of the 10.0.0.0 network, but I can't even pass the Internet through to the inside.
Also, this will eventually be behind another hosted firewall, so I'm not worried about restricting access, even currently.
However, I suspect the problem is that traffic is being blocked with the NAT rules or Access rules.
I wish I could just disable those inherent deny rules
Outside of pings to 10.209.0.3, all pings come back as request timed out.
Can someone please review this, and see if they notice anything I can change?
I do appreciate it....
Config:
: Saved
ASA Version 8.2(5)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.0 Eventual
name 10.209.0.0 Local
name 67.139.113.216 T1
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 0
ip address 10.209.0.3 255.0.0.0
interface Vlan2
nameif outside
security-level 0
ip address 67.139.113.218 255.255.255.248
time-range Indefinite
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
protocol-object udp
protocol-object tcp
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_1 Local 255.255.255.0 any time-range Indefinite
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any inside
asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 0.0.0.0 0.0.0.0 dns tcp 255 255  udp 255
access-group inside_access_in in interface inside
route inside 0.0.0.0 0.0.0.0 67.139.113.217 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Eventual 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 10.209.0.201-10.209.0.232 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd auto_config outside interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
  message-length maximum client auto
  message-length maximum 512
policy-map global_policy
class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny 
  inspect sunrpc
  inspect xdmcp
  inspect sip 
  inspect netbios
  inspect tftp
  inspect ip-options
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
Cryptochecksum:d3c4872f997a93984332213f98fbe12b
: end
asdm location Eventual 255.0.0.0 inside
asdm location Local 255.255.255.0 inside
asdm location T1 255.255.255.248 inside
asdm history enable

Unfortunately that didn't work....
The new config:
: Saved
ASA Version 8.2(5)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.0 Eventual
name 10.209.0.0 Local
name 67.139.113.216 T1
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 0
ip address 10.209.0.3 255.0.0.0
interface Vlan2
nameif outside
security-level 0
ip address 67.139.113.218 255.255.255.248
time-range Indefinite
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
protocol-object udp
protocol-object tcp
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any inside
asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route inside 0.0.0.0 0.0.0.0 67.139.113.217 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Eventual 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 10.209.0.201-10.209.0.232 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd auto_config outside interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
  message-length maximum client auto
  message-length maximum 512
policy-map global_policy
class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny 
  inspect sunrpc
  inspect xdmcp
  inspect sip 
  inspect netbios
  inspect tftp
  inspect ip-options
  inspect icmp
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
Cryptochecksum:64bbf533cf1bd591e797c053ea9e107a
: end
asdm location Eventual 255.0.0.0 inside
asdm location Local 255.255.255.0 inside
asdm location T1 255.255.255.248 inside
asdm history enable
I am getting some more encouraging messages in the Syslog, but I still cannot bing 8.8.8.8 or the outside interface.
5
Aug 29 2008
01:42:55
8.8.4.4
53
Asymmetric NAT rules matched for forward and reverse flows; Connection for udp src inside:10.209.0.6/64477 dst inside:8.8.4.4/53 denied due to NAT reverse path failure
6
Aug 29 2008
01:42:54
10.209.0.6
1686
SSL session with client inside:10.209.0.6/1686 terminated.
6
Aug 29 2008
01:42:54
10.209.0.6
1686
10.209.0.3
443
Deny TCP (no connection) from 10.209.0.6/1686 to 10.209.0.3/443 flags FIN ACK on interface inside

Similar Messages

  • Cisco ASA 5505 - Keeps dropping internet connection

    Hi,
    We are having some issues with our Cisco ASA 5505 unit, it intermittently drops the outside interface connection. Internally the network appears to be working correctly with no issues. Even though the outside interface indicates it is 'up' access to the internet is lost from our LAN. This seems to be ocourring more and more often! This is happening for all users on the network too. Reloading the ASA seems to correct the problem temporally but this isn't really an option during peak periods in the day as this would obviously hinder work being carried out by employees.
    Any ideas?
    Any help would be greatly appreciated!!
    Thanks,
    John
    Running Config Below:
    ASA Version 8.2(1)
    hostname ******************
    domain-name *************************
    enable password ************************* encrypted
    passwd **************************** encrypted
    names
    dns-guard
    interface Vlan1
    nameif inside
    security-level 100
    ip address 10.3.0.254 255.255.0.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address ***************** 255.255.255.248
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns domain-lookup inside
    dns domain-lookup outside
    dns server-group DefaultDNS
    name-server *****************
    domain-name **********************
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    access-list outside_access_in extended permit tcp any any eq smtp
    access-list outside_access_in extended permit tcp any any eq 3389
    access-list outside_access_in extended permit tcp any any eq https
    access-list outside_access_in extended permit tcp any any
    access-list outside_access_in extended permit tcp any any eq 3839
    pager lines 24
    logging enable
    logging asdm warnings
    mtu inside 1500
    mtu outside 1500
    failover timeout -1
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-621.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 1 0.0.0.0 0.0.0.0
    static (inside,outside) tcp interface smtp 10.3.0.2 smtp netmask 255.255.255.255
    static (inside,outside) tcp interface https 10.3.0.2 https netmask 255.255.255.255
    static (inside,outside) tcp interface 3839 10.3.0.1 3839 netmask 255.255.255.255
    static (inside,outside) tcp interface 3389 10.3.0.1 3389 netmask 255.255.255.255
    static (inside,inside) 10.3.0.0 10.3.0.0 netmask 255.255.0.0 norandomseq nailed
    static (inside,inside) 172.16.63.0 172.16.63.0 netmask 255.255.255.240 norandomseq nailed
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 *************** 1
    route inside 172.16.63.0 255.255.255.240 10.3.0.253 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 10.3.0.0 255.255.0.0 inside
    http 10.3.0.0 255.255.255.0 inside
    http 10.10.2.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    sysopt noproxyarp inside
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash md5
    group 1
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics port
    threat-detection statistics protocol
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    username ************ password *********************** encrypted privilege 15
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global

    Hello,
    What happens when you assign eth0 as internal interface and eth1 as outside if?
    Also configure logging (/debugging) to see if there are hardware issues or something else.
    And it seems you have a range of public addresses. What happens when you connect a device, e.g. a laptop directly on the internet access device and send continue ping to an internet host.
    When you loose internet connectivity, is the laptop still pinging to that host?
    Hopefully this helps you,
    Kind regards,
    Ralph Willemsen
    Arnhem, Netherlands

  • Cisco ASA 5505 Firewall Not Allowing Incoming Traffic

    Hello,
    I am wondering if there is a very friendly cisco guru out there who can help me out.  I am trying to switch out a cisco pix 501 firewall with a cisco ASA 5505 firewall.  I am not very familiar with all of the commands for the firewalls and have always relied on a standard command line script that I use when building a new one.  Unfortunately, my script is not working with the 5505.  Can someone please let me know what I am doing wrong with the following script?  I've masked public IP info with xxx.xxx.xxx and I run it right after restoring the firewall to the factory defaults.  I am able to get out to the internet if I browse directly from one of the servers, but cannot access a web page when trying to browse to it from an outside network.
    access-list 100 permit icmp any any echo-reply
    access-list 100 permit icmp any any time-exceeded 
    access-list 100 permit icmp any any unreachable
    ip address outside xxx.xxx.xxx.94 255.255.255.224
    ip address inside 192.168.1.1 255.255.255.0
    global (outside) 1 xxx.xxx.xxx.106-xxx.xxx.xxx.116
    global (outside) 1 xxx.xxx.xxx.95
    nat (inside) 1 0.0.0.0 0.0.0.0 0 0
    route outside 0 0 xxx.xxx.xxx.93
    access-group 100 in interface outside
    nat (inside) 1 192.168.1.0 255.255.255.0
    nat (inside) 1 192.168.1.0 255.255.255.0 0 0
    outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.93 1 DHCP static
    static (inside,outside) xxx.xxx.xxx.95 192.168.1.95 netmask 255.255.255.255 0 0
    access-list 100 permit tcp any host xxx.xxx.xxx.95 eq www
    static (inside,outside) xxx.xxx.xxx.96 192.168.1.96 netmask 255.255.255.255 0 0
    access-list 100 permit tcp any host xxx.xxx.xxx.96 eq www

    Hey Craig,
    Based on your commands I think you were using 6.3 version on PIX and now you must be  moving to ASA ver 8.2.x.
    On 8.4 for interface defining use below mentioned example :
    int eth0/0
    ip add x.x.x.x y.y.y.y
    nameif outside
    no shut
    int eth0/1
    ip add x.x.x.x y.y.y.y
    nameif inside
    no shut
    nat (inside) 1 192.168.1.0 255.255.255.0
    global (outside) 1 xxx.xxx.xxx.106-xxx.xxx.xxx.116
    global (outside) 1 xxx.xxx.xxx.95
    access-list 100 permit icmp any any echo-reply
    access-list 100 permit icmp any any time-exceeded 
    access-list 100 permit icmp any any unreachable
    static (inside,outside) xxx.xxx.xxx.95 192.168.1.95 netmask 255.255.255.255 0 0
    access-list 100 permit tcp any host xxx.xxx.xxx.95 eq www
    static (inside,outside) xxx.xxx.xxx.96 192.168.1.96 netmask 255.255.255.255 0 0
    access-list 100 permit tcp any host xxx.xxx.xxx.96 eq www
    route outside 0 0 xxx.xxx.xxx.93
    access-group 100 in interface outside
    You can use two global statements as first statement would be used a dynamic NAT and second as PAT.
    If you're still not able to reach.Paste your entire config and version that you are using on ASA.

  • Cisco ASA 5505 Site to Site VPN Problem

    Hi All,
    We have a site to site VPN with a cisco asa 5505 on one end and a Checkpoint firewall on the other end.
    We can establish the vpn tunnel and all users in the remote office are working great. However at a random point during the day or it may even be after 2 weeks of working, the tunnel between the sites automatically fails.
    When I dial into the modem which is connected to the firewall I see the following messages in the logs:
    Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
    Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
    Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
    Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
    Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
    Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
    Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
    Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
    Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
    Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
    Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
    Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
    There is nothing in the Checkpoint logs. To solve the issue I have to reload the firewall.
    I have checked both firewalls for any mis-matched parameters and do not see any.
    Any help is very much appreciated as it is very frustrating for myself and the users in the remote office.
    Thanks!

    Also to note, PFS is enabled on both firewalls. Config on Cisco ASA firewall as follows:
    hostname
    domain-name
    enable passwordpasswd names
    interface Vlan701
    nameif inside
    security-level 100
    ip address 10.65.0.69 255.255.255.252
    interface Vlan999
    nameif outside
    security-level 0
    ip address ******  255.255.255.248
    interface Ethernet0/0
    description Link to Internet
    switchport access vlan 999
    interface Ethernet0/1
    description
    switchport access vlan 701
    interface range Ethernet0/2 - 0/7
    switchport access vlan 2
    shutdown
    ftp mode passive
    dns server-group DefaultDNS
    domain-name******
    access-list 101 extended permit ip host ****** 172.25.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 host ******
    access-list 101 extended permit ip 10.65.0.64 255.255.255.192 ******* 255.255.255.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
    access-list nonat extended permit ip 10.65.0.64 255.255.255.192 ******** 255.255.255.0
    pager lines 24
    logging enable
    logging timestamp
    logging buffered warnings
    logging trap warnings
    logging asdm informational
    logging host outside *****
    mtu inside 1500
    mtu outside 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm history enable
    arp timeout 14400
    nat (inside) 0 access-list nonat
    route inside ******
    route outside 0.0.0.0 0.0.0.0 ********
    timeout xlate 0:05:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server RADIUS protocol radius
    aaa authentication ssh console LOCAL
    aaa authentication telnet console LOCAL
    snmp-server location **:
    snmp-server contact **
    snmp-server community shortkey
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    snmp-server enable traps syslog
    crypto ipsec transform-set 3desmd5 esp-3des esp-md5-hmac
    crypto map CASGMAP 50 match address 101
    crypto map CASGMAP 50 set pfs group1
    crypto map CASGMAP 50 set peer ********
    crypto map CASGMAP 50 set transform-set 3desmd5
    crypto map CASGMAP 50 set security-association lifetime seconds 3600
    crypto map CASGMAP interface outside
    crypto isakmp enable outside
    crypto isakmp policy 20
    authentication pre-share
    encryption 3des
    hash md5
    group 2
    lifetime 86400
    telnet **** inside
    telnet timeout 5
    ssh **** inside
    ssh **** outside
    ssh timeout 5
    console timeout 30
    management-access inside
    dhcpd ping_timeout 750
    priority-queue outside
    ntp server **
    username ***
    tunnel-group ******** type ipsec-l2l
    tunnel-group ******** ipsec-attributes
    pre-shared-key ***
    class-map VoIP
    match dscp ef
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map General-purpose
    class VoIP
    priority
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect skinny
      inspect esmtp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect sip
      inspect xdmcp
      inspect http
    service-policy General-purpose interface outside
    prompt hostname context

  • Cisco asa 5505 issues ( ROUTING AND PAT)

    I have some issues with my cisco asa 5505 config. Please see details below:
    NETWORK SETUP:
    gateway( 192.168.223.191)   - cisco asa 5505 ( outside - 192.168.223.200 , inside - 192.168.2.253, DMZ - 172.16.3.253 )  -
    ISSUES:
    1)
    no route from DMZ to outside
    example:
    ping from 172.16.3201 to the gateway
    6          Jan 27 2014          11:15:33                    172.16.3.201          39728                              Failed to locate egress interface for ICMP from outside:172.16.3.201/39728 to 172.16.3.253/0
    2)
    not working access from external to DMZ AT ALL
    ASA DETAILS:
    cisco asa5505
    Device license          Base
    Maximum Physical Interfaces          8          perpetual
    VLANs          3      DMZ Restricted
    Inside Hosts          Unlimited          perpetual
    configuration:
    firewall200(config)# show run
    : Saved
    ASA Version 9.1(3)
    hostname firewall200
    domain-name test1.com
    enable password xxxxxxxxxxx encrypted
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    passwd XXXXXXXXXXX encrypted
    names
    interface Ethernet0/0
    switchport access vlan 100
    interface Ethernet0/1
    switchport access vlan 200
    interface Ethernet0/2
    switchport access vlan 200
    interface Ethernet0/3
    switchport access vlan 200
    interface Ethernet0/4
    switchport access vlan 300
    interface Ethernet0/5
    switchport access vlan 300
    interface Ethernet0/6
    switchport access vlan 300
    interface Ethernet0/7
    switchport access vlan 300
    interface Vlan100
    nameif outside
    security-level 0
    ip address 192.168.223.200 255.255.255.0
    interface Vlan200
    mac-address 001b.539c.597e
    nameif inside
    security-level 100
    ip address 172.16.2.253 255.255.255.0
    interface Vlan300
    no forward interface Vlan200
    nameif DMZ
    security-level 50
    ip address 172.16.3.253 255.255.255.0
    boot system disk0:/asa913-k8.bin
    boot config disk0:/startup-config.cfg
    ftp mode passive
    clock timezone GMT/BST 0
    clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns server-group DefaultDNS
    domain-name test1.com
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    object network office1-int
    host 172.16.2.1
    object network firewall-dmz-gateway
    host 172.16.3.253
    object network firewall-internal-gateway
    host 172.16.2.253
    object network com1
    host 192.168.223.227
    object network web2-ext
    host 192.168.223.201
    object network web2-int
    host 172.16.3.201
    object network gateway
    host 192.168.223.191
    object network office1-int
    host 172.16.2.1
    object-group network DMZ_SUBNET
    network-object 172.16.3.0 255.255.255.0
    object-group service www tcp
    port-object eq www
    port-object eq https
    access-list DMZ_access_in extended permit icmp any any
    access-list DMZ_access_in extended permit ip any any
    access-list outside_access_in extended permit tcp any object web2-ext eq www
    pager lines 24
    logging enable
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    mtu DMZ 1500 
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-714.bin
    no asdm history enable
    arp DMZ 172.16.4.199 001b.539c.597e alias
    arp DMZ 172.16.3.199 001b.539c.597e alias
    arp timeout 14400
    no arp permit-nonconnected
    object network web2-int
    nat (DMZ,outside) static web2-ext service tcp www www
    access-group outside_access_in in interface outside
    access-group DMZ_access_in in interface DMZ
    route inside 172.168.2.0 255.255.255.0 192.168.223.191 1
    route inside 172.168.3.0 255.255.255.0 192.168.223.191 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.223.227 255.255.255.255 outside
    http 172.163.2.5 255.255.255.255 outside
    http 172.163.2.5 255.255.255.255 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec security-association pmtu-aging infinite
    crypto ca trustpool policy
    telnet timeout 5
    ssh 192.168.223.227 255.255.255.255 outside
    ssh 172.163.2.5 255.255.255.255 outside
    ssh 172.163.2.5 255.255.255.255 inside
    ssh timeout 60
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    dhcpd address 172.16.2.10-172.16.2.10 inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    ntp server 176.58.109.199 source outside prefer
    ntp server 81.150.197.169 source outside
    ntp server 82.113.154.206
    username xxxx password xxxxxxxxx encrypted
    class-map DMZ-class
    match any
    policy-map global_policy
    policy-map DMZ-policy
    class DMZ-class
      inspect icmp
    service-policy DMZ-policy interface DMZ
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:9c73fa27927822d24c75c49f09c67c24
    : end

    Thank you one more time for everthing. It is workingin indeed
    Reason why maybe sometimes I had some 'weird' results was because I had all devices connected to the same switch.Separtated all networks to a different switches helped.Anyway if you could take a look one last time to my configuration and let me know if it's good enough to deploy it on live ( only www for all , ssh restricted from outside, lan to dmz) .Thanks one more time.
    show run
    : Saved
    ASA Version 9.1(3)
    hostname firewall200
    domain-name test1.com
    enable password xxxxxxxxxx encrypted
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    passwd xxxxxxxxxxxx encrypted
    names
    interface Ethernet0/0
    switchport access vlan 100
    interface Ethernet0/1
    switchport access vlan 200
    interface Ethernet0/2
    switchport access vlan 200
    interface Ethernet0/3
    switchport access vlan 200
    interface Ethernet0/4
    switchport access vlan 300
    interface Ethernet0/5
    switchport access vlan 300
    interface Ethernet0/6
    switchport access vlan 300
    interface Ethernet0/7
    switchport access vlan 300
    interface Vlan100
    nameif outside
    security-level 0
    ip address 192.168.223.200 255.255.255.0
    interface Vlan200
    mac-address 001b.539c.597e
    nameif inside
    security-level 100
    ip address 172.16.2.253 255.255.255.0
    interface Vlan300
    no forward interface Vlan200
    nameif DMZ
    security-level 50
    ip address 172.16.3.253 255.255.255.0
    boot system disk0:/asa913-k8.bin
    boot config disk0:/startup-config.cfg
    ftp mode passive
    clock timezone GMT/BST 0
    clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00
    dns domain-lookup inside
    dns domain-lookup DMZ
    dns server-group DefaultDNS
    name-server 8.8.8.8
    name-server 8.8.4.4
    domain-name test1.com
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    object network firewall-dmz-gateway
    host 172.16.3.253
    object network firewall-internal-gateway
    host 172.16.2.253
    object network com1
    host 192.168.223.227
    object network web2-ext
    host 192.168.223.201
    object network web2-int
    host 172.16.3.201
    object network gateway
    host 192.168.223.191
    object network office1-int
    host 172.16.2.1
    object-group network DMZ_SUBNET
    network-object 172.16.3.0 255.255.255.0
    object-group service www tcp
    port-object eq www
    port-object eq https
    access-list DMZ_access_in extended permit icmp any any
    access-list DMZ_access_in extended permit ip any any
    access-list DMZ_access_in extended permit tcp 172.16.3.0 255.255.255.0 interface outside eq ssh
    access-list outside_access_in extended permit tcp any object web2-int eq www
    access-list outside_access_in extended permit tcp any object web2-int eq ssh
    pager lines 24
    logging enable
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    mtu DMZ 1500
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit any inside
    icmp permit any DMZ
    asdm image disk0:/asdm-714.bin
    no asdm history enable
    arp DMZ 172.16.4.199 001b.539c.597e alias
    arp DMZ 172.16.3.199 001b.539c.597e alias
    arp timeout 14400
    no arp permit-nonconnected
    object network web2-int
    nat (DMZ,outside) static web2-ext net-to-net
    access-group outside_access_in in interface outside
    access-group DMZ_access_in in interface DMZ
    route outside 0.0.0.0 0.0.0.0 192.168.223.191 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.223.227 255.255.255.255 outside
    http 172.163.2.5 255.255.255.255 outside
    http 172.163.2.5 255.255.255.255 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec security-association pmtu-aging infinite
    crypto ca trustpool policy
    telnet timeout 5
    ssh 192.168.223.227 255.255.255.255 outside
    ssh 172.163.2.5 255.255.255.255 outside
    ssh 172.16.3.253 255.255.255.255 outside
    ssh 172.163.2.5 255.255.255.255 inside
    ssh timeout 60
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    ntp server 176.58.109.199 source outside prefer
    ntp server 81.150.197.169 source outside
    ntp server 82.113.154.206
    username xxxxx password xxxxxxxxx encrypted
    class-map DMZ-class
    match any
    policy-map global_policy
    policy-map DMZ-policy
    class DMZ-class
      inspect icmp
    service-policy DMZ-policy interface DMZ
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:f264c94bb8c0dd206385a6b72afe9e5b
    : end

  • Cisco VPN 3002 to Cisco ASA 5505

    I want to remove a Cisco VPN 3002 Hardware client and replace it with a Cisco ASA 5505.  Is there a way to do this? I want to have the remote user and group authentication and no split tunneling.? 
    Thanks for your help.

    Sure can.
    Here is a sample configuration for ASA5505 acting as a remote hardware easy vpn client (like the VPN3002):
    http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00808a61f4.shtml
    If you don't want split tunneling, then I assume that it is in PAT/client mode instead of NEM mode as above sample configuration.
    You can just change the "vpnclient mode network-extension-mode" to "vpnclient mode client-mode"
    Hope this helps.

  • Setting up site to site vpn with cisco asa 5505

    I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
    IP of remote office router is 71.37.178.142
    IP of the main office firewall is 209.117.141.82
    Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
    ciscoasa# show run
    : Saved
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password TMACBloMlcBsq1kp encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs group5
    crypto map outside_map 1 set peer 209.117.141.82
    crypto map outside_map 1 set transform-set ESP-AES-256-SHA
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    vpdn username [email protected] password ********* store-local
    dhcpd auto_config outside
    dhcpd address 192.168.1.2-192.168.1.129 inside
    dhcpd enable inside
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
    : end
    ciscoasa#
    Thanks!

    Hi Mandy,
    By using following access list define Peer IP as source and destination
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    you are not defining the interesting traffic / subnets from both ends.
    Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
    !.1..source subnet(called local encryption domain) at your end  192.168.200.0
    !..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
    !..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
    !...at your end  192.168.200.0
    !..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
    !...at other end 192.168.100.0
    Please use Baisc Steps as follows:
    A. Configuration in your MAIN office  having IP = 209.117.141.82  (follow step 1 to 6)
    Step 1.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    Step 2.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 3.
    Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 71.37.178.142
    or , but not both
    crypto isakmp key 6 CISCO123 address71.37.178.142
    step 4.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 5.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 6.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Configure the same but just change ACL on other end in step one  by reversing source and destination
    and also set the peer IP of this router in other end.
    So other side config should look as follows:
    B.  Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
    Step 7.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
    Step 8.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 9.
    Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 209.117.141.82
    or , but not both
    crypto isakmp key 6 CISCO123 address 209.117.141.82
    step 10.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 11.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map    ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set, only one is permissible
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 12.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Now initite a ping
    Here is for your summary:
    IPSec: Site to Site - Routers
    Configuration Steps
    Phase 1
    Step 1: Configure Mirrored ACL/Crypto ACL       for Interesting Traffic
    Step 2: Configure ISAKMP Policy
    Step 3: Configure ISAKMP Key
    Phase 2
    Step 4: Configure Transform Set
    Step 5: Configure Crypto Map
    Step 6: Apply Crypto Map to an Interface
    To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
    Router#debug crpyto isakmp
    Router#debug crpyto ipsec
    Router(config)# logging buffer 7
    Router(config)# logging buffer 99999
    Router(config)# logging console 6
    Router# clear logging
    Configuration
    In R1:
    (config)# access-list 101 permit ipo host 10.1.1.1 host      10.1.2.1
    (config)# crypto isakmp policy 10
    (config-policy)# encryption 3des
    (config-policy)# authentication pre-share
    (config-policy)# group 2
    (config-policy)# hash sha1
    (config)# crypto isakmp key 0 cisco address 2.2.2.1
    (config)# crypto ipsec transform-set TSET esp-3des      sha-aes-hmac
    (config)# crypto map CMAP 10 ipsec-isakmp
    (config-crypto-map)# set peer 2.2.2.1
    (config-crypto-map)# match address 101
    (config-crypto-map)# set transform-set TSET
    (config)# int f0/0
    (config-if)# crypto map CMAP
    Similarly in R2
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Change to Transport Mode, add the following command in Step 4:
    (config-tranform-set)# mode transport
    Even after  doing this change, the ipsec negotiation will still be done through  tunnel mode if pinged from Loopback to Loopback. To overcome this we  make changes to ACL.
    Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
    (config)# crypto isakmp peer address 2.2.2.1
    (config-peer)# set aggressive-mode password cisco
    (config-peer)# set aggressive-mode clien-endpoint       ipv4-address 2.2.2.1
    Similarly on R2.
    The below process is for the negotiation using RSA-SIG (PKI) as authentication type
    Debug Process:
    After  we debug, we can see the negotiation between the two peers. The first  packet of the interesting traffic triggers the ISAKMP (Phase1)  negotiation. Important messages are marked in BOLD and explanation in  RED
    R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
    Packet sent with a source address of 2.2.2.2
    Mar  2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) //  Router tried to find any IPSec SA matching the outgoing connection but  no valid SA has been found in Security Association Database (SADB)
    Mar  2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
    Mar  2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
    Mar  2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
    Mar  2 16:18:42.939: ISAKMP: local port 500, remote port 500
    Mar  2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE    
    Mar  2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
    Mar  2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
    Mar  2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
    Mar  2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
    Mar  2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY  New State = IKE_I_MM1
    Mar  2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
    Mar  2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1  New State = IKE_I_MM2
    Mar  2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947:.!!!!
    Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
    R2(config)# ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
    Mar  2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
    Mar  2 16:18:42.947: ISAKMP:      encryption 3DES-CBC
    Mar  2 16:18:42.947: ISAKMP:      hash SHA
    Mar  2 16:18:42.947: ISAKMP:      default group 2
    Mar  2 16:18:42.947: ISAKMP:      auth RSA sig
    Mar  2 16:18:42.947: ISAKMP:      life type in seconds
    Mar  2 16:18:42.947: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80
    Mar  2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
    Mar  2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
    Mar  2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM2
    Mar  2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
    Mar  2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM3
    Mar  2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
    Mar  2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3  New State = IKE_I_MM4
    Mar  2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
    Mar  2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:43.007:  Choosing trustpoint CA_Server as issuer
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
    Mar  2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM4
    Mar  2 16:18:43.011: ISAKMP:(1008):Send initial contact
    Mar  2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
    Mar  2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
    Mar  2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
    Mar  2 16:18:43.011: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : R2
              protocol     : 17
              port         : 500
              length       : 10
    Mar  2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
    Mar  2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
    Mar  2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
    Mar  2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
    Mar  2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM5
    Mar  2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
    // "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : ASA1
              protocol     : 0
              port         : 0
              length       : 12
    Mar  2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
    Mar  2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
    Mar  2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
    Mar  2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
    Mar  2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
    Mar  2 16:18:43.067: ISAKMP:received payload type 17
    Mar  2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
    Mar  2 16:18:43.067: ISAKMP:(1008):SA authentication status:
              authenticated
    Mar  2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
    Mar  2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/,  and inserted successfully 46519678. // SA inserted into SADB
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5  New State = IKE_I_MM6
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_I_MM6
    Mar  2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
    Mar  2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
    Mar  2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY  New State = IKE_QM_I_QM1
    Mar  2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
    Mar  2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
    Mar  2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
    Mar  2 16:18:43.079: ISAKMP:   attributes in transform:
    Mar  2 16:18:43.079: ISAKMP:      SA life type in seconds
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (basic) of 3600
    Mar  2 16:18:43.079: ISAKMP:      SA life type in kilobytes
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0
    Mar  2 16:18:43.079: ISAKMP:      encaps is 1 (Tunnel)
    Mar  2 16:18:43.079: ISAKMP:      authenticator is HMAC-SHA
    Mar  2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
    Mar  2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
    Mar  2 16:18:43.083:         inbound SA from 20.1.1.10 to 40.1.1.1 (f/i)  0/ 0
              (proxy 1.1.1.1 to 2.2.2.2)
    Mar  2 16:18:43.083:         has spi 0xA9A66D46 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083:         outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
              (proxy 2.2.2.2 to 1.1.1.1)
    Mar  2 16:18:43.083:         has spi  0x2B367FB4 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
    Mar  2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
    Mar  2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1  New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Kindly rate if you find the explanation useful !!
    Best Regards
    Sachin Garg

  • Internet Connection Became Slow after Introduction of Cisco ASA 5505 to the Network

    I configured a Cisco ASA 5505 (Version Cisco Adaptive Security Appliance Software Version 7.2(3)
    Device Manager Version 5.2(3)
    in transparent firewall mode and inserted after Cisco 1700 router. However, the internet connection became very slow and users are compaining that they cannot load any pages.
    My setup looks like:
    Internet --> Cisco 1700 --> Cisco ASA 5505 --> LAN
    The license information is:
    Licensed features for this platform:
    Maximum Physical Interfaces : 8
    VLANs                       : 3, DMZ Restricted
    Inside Hosts                : Unlimited
    Failover                    : Disabled
    VPN-DES                     : Enabled
    VPN-3DES-AES                : Enabled
    VPN Peers                   : 10
    WebVPN Peers                : 2
    Dual ISPs                   : Disabled
    VLAN Trunk Ports            : 0
    This platform has a Base license.
    The flash activation key is the SAME as the running key.
    My running-config looks like:
    ASA Version 7.2(3)
    firewall transparent
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password 8Ry2YjIyt7RRXU24 encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    no shut
    interface Vlan2
    nameif outside
    security-level 0
    no shut
    interface Ethernet0/0
    switchport access vlan 2
    no shut
    interface Ethernet0/1
    no shut
    interface Ethernet0/2
    no shut
    interface Ethernet0/3
    no shut
    interface Ethernet0/4
    no shut
    interface Ethernet0/5
    no shut
    interface Ethernet0/6
    no shut
    interface Ethernet0/7
    no shut
    passwd 2KFQnbNIdI.2KYOU encrypted
    regex urllist1 ".*\.([Ee][Xx][Ee]|[Cc][Oo][Mm]|[Bb][Aa][Tt]) HTTP/1.[01]"
    regex urllist2 ".*\.([Pp][Ii][Ff]|[Vv][Bb][Ss]|[Ww][Ss][Hh]) HTTP/1.[01]"
    regex urllist3 ".*\.([Dd][Oo][Cc]|[Xx][Ll][Ss]|[Pp][Pp][Tt]) HTTP/1.[01]"
    regex urllist4 ".*\.([Zz][Ii][Pp]|[Tt][Aa][Rr]|[Tt][Gg][Zz]) HTTP/1.[01]"
    regex domainlist1 "\.facebook\.com"
    regex domainlist2 "\.diretube\.com"
    regex domainlist3 "\.youtube\.com"
    regex domainlist4 "\.vimeo\.com"
    regex applicationheader "application/.*"
    regex contenttype "Content-Type"
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list outside_in extended permit ip any any
    access-list inside_mpc extended permit tcp any any eq www
    access-list inside_mpc extended permit tcp any any eq 8080
    pager lines 24
    mtu outside 1500
    mtu inside 1500
    ip address 192.168.1.254 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    access-group outside_in in interface outside
    route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout uauth 0:05:00 absolute
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    class-map type regex match-any DomainBlockList
    match regex domainlist1
    match regex domainlist2
    match regex domainlist3
    match regex domainlist4
    class-map type inspect http match-all BlockDomainsClass
    match request header host regex class DomainBlockList
    class-map type regex match-any URLBlockList
    match regex urllist1
    match regex urllist2
    match regex urllist3
    match regex urllist4
    class-map inspection_default
    match default-inspection-traffic
    class-map type inspect http match-all AppHeaderClass
    match response header regex contenttype regex applicationheader
    class-map httptraffic
    match access-list inside_mpc
    class-map type inspect http match-all BlockURLsClass
    match request uri regex class URLBlockList
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map type inspect http http_inspection_policy
    parameters
      protocol-violation action drop-connection
    class AppHeaderClass
      drop-connection log
    match request method connect
      drop-connection log
    class BlockDomainsClass
      reset log
    class BlockURLsClass
      reset log
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect skinny
      inspect esmtp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect sip
      inspect xdmcp
    policy-map inside-policy
    class httptraffic
      inspect http http_inspection_policy
    service-policy global_policy global
    service-policy inside-policy interface inside
    prompt hostname context
    Cryptochecksum:8ab1a53df6ae3c202aee236d6080edfd
    : end
    Could the slow internet connection be due to license limitations? Or is there something wrong with my configuration?
    Please see the configuration and help.
    Thanks

    I have re-configured the ASA 5505 yesterday and so far it's working fine. I am not sure if the problem will re-appear later on. Anyways here is my sh tech-support
    ciscoasa# sh tech-support
    Cisco Adaptive Security Appliance Software Version 7.2(3)
    Device Manager Version 5.2(3)
    Compiled on Wed 15-Aug-07 16:08 by builders
    System image file is "disk0:/asa723-k8.bin"
    Config file at boot was "startup-config"
    ciscoasa up 14 hours 16 mins
    Hardware:   ASA5505, 256 MB RAM, CPU Geode 500 MHz
    Internal ATA Compact Flash, 128MB
    BIOS Flash M50FW080 @ 0xffe00000, 1024KB
    Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
                                 Boot microcode   : CNlite-MC-Boot-Cisco-1.2
                                 SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
                                 IPSec microcode  : CNlite-MC-IPSECm-MAIN-2.04
    0: Int: Internal-Data0/0    : address is 001f.9ee8.ffa2, irq 11
    1: Ext: Ethernet0/0         : address is 001f.9ee8.ff9a, irq 255
    2: Ext: Ethernet0/1         : address is 001f.9ee8.ff9b, irq 255
    3: Ext: Ethernet0/2         : address is 001f.9ee8.ff9c, irq 255
    4: Ext: Ethernet0/3         : address is 001f.9ee8.ff9d, irq 255
    5: Ext: Ethernet0/4         : address is 001f.9ee8.ff9e, irq 255
    6: Ext: Ethernet0/5         : address is 001f.9ee8.ff9f, irq 255
    <--- More --->
    7: Ext: Ethernet0/6         : address is 001f.9ee8.ffa0, irq 255
    8: Ext: Ethernet0/7         : address is 001f.9ee8.ffa1, irq 255
    9: Int: Internal-Data0/1    : address is 0000.0003.0002, irq 255
    10: Int: Not used            : irq 255
    11: Int: Not used            : irq 255
    Licensed features for this platform:
    Maximum Physical Interfaces : 8        
    VLANs                       : 3, DMZ Restricted
    Inside Hosts                : Unlimited
    Failover                    : Disabled
    VPN-DES                     : Enabled  
    VPN-3DES-AES                : Enabled  
    VPN Peers                   : 10       
    WebVPN Peers                : 2        
    Dual ISPs                   : Disabled 
    VLAN Trunk Ports            : 0        
    This platform has a Base license.
    Serial Number: JMX1211Z2N4
    Running Activation Key: 0xaf0ed046 0xbcf18ebf 0x80b38508 0xba785cc0 0x05250493
    Configuration register is 0x1
    Configuration has not been modified since last system restart.
    <--- More --->
    ------------------ show clock ------------------
    18:32:58.254 UTC Tue Nov 26 2013
    ------------------ show memory ------------------
    Free memory:       199837144 bytes (74%)
    Used memory:        68598312 bytes (26%)
    Total memory:      268435456 bytes (100%)
    ------------------ show conn count ------------------
    1041 in use, 2469 most used
    ------------------ show xlate count ------------------
    0 in use, 0 most used
    ------------------ show blocks ------------------
      SIZE    MAX    LOW    CNT
         0    100     68    100
    <--- More --->
         4    300    299    299
        80    100     92    100
       256    100     94    100
      1550   6174   6166   6174
      2048   1124    551    612
    ------------------ show blocks queue history detail ------------------
    History buffer memory usage: 2136 bytes (default)
    ------------------ show interface ------------------
    Interface Internal-Data0/0 "", is up, line protocol is up
      Hardware is y88acs06, BW 1000 Mbps
    (Full-duplex), (1000 Mbps)
    MAC address 001f.9ee8.ffa2, MTU not set
    IP address unassigned
    18491855 packets input, 11769262614 bytes, 0 no buffer
    Received 213772 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops, 0 demux drops
    18185861 packets output, 11626494317 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 late collisions, 0 deferred
    <--- More --->
    0 input reset drops, 0 output reset drops
    input queue (curr/max packets): hardware (0/0) software (0/0)
    output queue (curr/max packets): hardware (0/55) software (0/0)
      Control Point Interface States:
    Interface number is unassigned
    Interface Internal-Data0/1 "", is administratively down, line protocol is up
      Hardware is 88E6095, BW 1000 Mbps
    (Full-duplex), (1000 Mbps)
    MAC address 0000.0003.0002, MTU not set
    IP address unassigned
    18184216 packets input, 11625360131 bytes, 0 no buffer
    Received 206655 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 switch ingress policy drops
    18490057 packets output, 11768078777 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    0 switch egress policy drops
      Control Point Interface States:
    Interface number is unassigned
    Interface Loopback0 "_internal_loopback", is up, line protocol is up
      Hardware is VirtualMAC address 0000.0000.0000, MTU 1500
    IP address 127.1.0.1, subnet mask 255.255.0.0
    <--- More --->
      Traffic Statistics for "_internal_loopback":
    1 packets input, 28 bytes
    1 packets output, 28 bytes
    1 packets dropped
          1 minute input rate 0 pkts/sec,  0 bytes/sec
          1 minute output rate 0 pkts/sec,  0 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 0 pkts/sec,  0 bytes/sec
          5 minute output rate 0 pkts/sec,  0 bytes/sec
          5 minute drop rate, 0 pkts/sec
      Control Point Interface States:
    Interface number is 28
    Interface config status is active
    Interface state is active
    Interface Vlan1 "inside", is up, line protocol is up
      Hardware is EtherSVI
    MAC address 001f.9ee8.ffa2, MTU 1500
    IP address 192.168.1.254, subnet mask 255.255.255.0
      Traffic Statistics for "inside":
    7742275 packets input, 903584114 bytes
    10645034 packets output, 10347291114 bytes
    184883 packets dropped
          1 minute input rate 320 pkts/sec,  35404 bytes/sec
          1 minute output rate 325 pkts/sec,  313317 bytes/sec
    <--- More --->
          1 minute drop rate, 17 pkts/sec
          5 minute input rate 399 pkts/sec,  59676 bytes/sec
          5 minute output rate 483 pkts/sec,  503200 bytes/sec
          5 minute drop rate, 9 pkts/sec
      Control Point Interface States:
    Interface number is 1
    Interface config status is active
    Interface state is active
    Interface Vlan2 "outside", is up, line protocol is up
      Hardware is EtherSVI
    MAC address 001f.9ee8.ffa3, MTU 1500
    IP address 192.168.1.254, subnet mask 255.255.255.0
      Traffic Statistics for "outside":
    10750090 packets input, 10432619059 bytes
    7541331 packets output, 870613684 bytes
    109911 packets dropped
          1 minute input rate 328 pkts/sec,  313770 bytes/sec
          1 minute output rate 301 pkts/sec,  32459 bytes/sec
          1 minute drop rate, 2 pkts/sec
          5 minute input rate 485 pkts/sec,  503789 bytes/sec
          5 minute output rate 387 pkts/sec,  57681 bytes/sec
          5 minute drop rate, 2 pkts/sec
      Control Point Interface States:
    Interface number is 2
    <--- More --->
    Interface config status is active
    Interface state is active
    Interface Ethernet0/0 "", is up, line protocol is up
      Hardware is 88E6095, BW 100 Mbps
    Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
    Available but not configured via nameif
    MAC address 001f.9ee8.ff9a, MTU not set
    IP address unassigned
    10749794 packets input, 10630700889 bytes, 0 no buffer
    Received 2506 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops
    3 switch ingress policy drops
    7541070 packets output, 1028190148 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    0 rate limit drops
    0 switch egress policy drops
      Control Point Interface States:
    Interface number is unassigned
    Interface Ethernet0/1 "", is up, line protocol is up
      Hardware is 88E6095, BW 100 Mbps
    Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
    <--- More --->
    Available but not configured via nameif
    MAC address 001f.9ee8.ff9b, MTU not set
    IP address unassigned
    7741977 packets input, 1064586806 bytes, 0 no buffer
    Received 211282 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops
    0 switch ingress policy drops
    10644663 packets output, 10543362751 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    0 rate limit drops
    0 switch egress policy drops
      Control Point Interface States:
    Interface number is unassigned
    Interface Ethernet0/2 "", is down, line protocol is down
      Hardware is 88E6095, BW 100 Mbps
    Auto-Duplex, Auto-Speed
    Available but not configured via nameif
    MAC address 001f.9ee8.ff9c, MTU not set
    IP address unassigned
    0 packets input, 0 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants
    <--- More --->
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops
    0 switch ingress policy drops
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    0 rate limit drops
    0 switch egress policy drops
      Control Point Interface States:
    Interface number is unassigned
    Interface Ethernet0/3 "", is down, line protocol is down
      Hardware is 88E6095, BW 100 Mbps
    Auto-Duplex, Auto-Speed
    Available but not configured via nameif
    MAC address 001f.9ee8.ff9d, MTU not set
    IP address unassigned
    0 packets input, 0 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops
    0 switch ingress policy drops
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    <--- More --->
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    0 rate limit drops
    0 switch egress policy drops
      Control Point Interface States:
    Interface number is unassigned
    Interface Ethernet0/4 "", is down, line protocol is down
      Hardware is 88E6095, BW 100 Mbps
    Auto-Duplex, Auto-Speed
    Available but not configured via nameif
    MAC address 001f.9ee8.ff9e, MTU not set
    IP address unassigned
    0 packets input, 0 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops
    0 switch ingress policy drops
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    0 rate limit drops
    0 switch egress policy drops
      Control Point Interface States:
    <--- More --->
    Interface number is unassigned
    Interface Ethernet0/5 "", is down, line protocol is down
      Hardware is 88E6095, BW 100 Mbps
    Auto-Duplex, Auto-Speed
    Available but not configured via nameif
    MAC address 001f.9ee8.ff9f, MTU not set
    IP address unassigned
    0 packets input, 0 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops
    0 switch ingress policy drops
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    0 rate limit drops
    0 switch egress policy drops
      Control Point Interface States:
    Interface number is unassigned
    Interface Ethernet0/6 "", is down, line protocol is down
      Hardware is 88E6095, BW 100 Mbps
    Auto-Duplex, Auto-Speed
    Available but not configured via nameif
    <--- More --->
    MAC address 001f.9ee8.ffa0, MTU not set
    IP address unassigned
    0 packets input, 0 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 L2 decode drops
    0 switch ingress policy drops
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    0 rate limit drops
    0 switch egress policy drops
      Control Point Interface States:
    Interface number is unassigned
    Interface Ethernet0/7 "", is down, line protocol is down
      Hardware is 88E6095, BW 100 Mbps
    Auto-Duplex, Auto-Speed
    Available but not configured via nameif
    MAC address 001f.9ee8.ffa1, MTU not set
    IP address unassigned
    0 packets input, 0 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    <--- More --->
    0 L2 decode drops
    0 switch ingress policy drops
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 0 interface resets
    0 babbles, 0 late collisions, 0 deferred
    0 lost carrier, 0 no carrier
    0 rate limit drops
    0 switch egress policy drops
      Control Point Interface States:
    Interface number is unassigned
    ------------------ show cpu usage ------------------
    CPU utilization for 5 seconds = 12%; 1 minute: 11%; 5 minutes: 11%
    ------------------ show cpu hogging process ------------------
    Process:      Dispatch Unit, NUMHOG: 1, MAXHOG: 133, LASTHOG: 140
    LASTHOG At:   04:45:59 UTC Nov 26 2013
    PC:           8be0f7
    Traceback:    8bed19  8bf553  302b87  3030a5  2fad69  7674bf  75ca16
                  c6251d  c62a4c  c62f6c  75c653  767820  797f64  769c85
    <--- More --->
    ------------------ show process ------------------
        PC       SP       STATE       Runtime    SBASE     Stack Process
    Mwe 00c9bb24 01bb8700 013e3250          0 01733fc8 15616/16384 emweb/cifs
    Lwe 001072ac 0176f9c4 013e32d0          0 0176d9f0 8132/8192 block_diag
    Mrd 00223a67 01783d5c 013e33b0     314854 0177be18 25752/32768 Dispatch Unit
    Msi 00f82847 01b07b84 013e3250        229 01b05bc0 7984/8192 y88acs06 OneSec Thread
    Mwe 0011b1a5 01b09cfc 013e3250          0 01b07d88 7864/8192 Reload Control Thread
    Mwe 00120606 01b1260c 013e5258          0 01b10988 7256/8192 aaa
    Mwe 001486aa 01b19404 013e5ae8          0 01b15450 16020/16384 CMGR Server Process
    Mwe 0014c3c5 01b1b4d4 013e3250          0 01b19570 7968/8192 CMGR Timer Process
    Lwe 002227a1 01b239b4 013ee360          0 01b219f0 7524/8192 dbgtrace
    Mwe 004e1ba5 01b29c34 013e3250        157 01b27d50 6436/8192 eswilp_svi_init
    Mwe 01064b1d 01b4a7f4 013e3250          0 01b48890 7848/8192 Chunk Manager
    Msi 008b61b6 01b52d54 013e3250        230 01b50da0 7856/8192 PIX Garbage Collector
    Lsi 00ecb6ac 01b54e94 013e3250         12 01b52ec0 7552/8192 route_process
    Mwe 008a5ddc 01b5dc04 0133b430          0 01b5bc40 8116/8192 IP Address Assign
    Mwe 00acb779 01b60604 01346e10          0 01b5e640 8116/8192 QoS Support Module
    Mwe 0091eba9 01b6275c 0133c530          0 01b60798 8116/8192 Client Update Task
    Lwe 01083c8e 01b656d4 013e3250     123088 01b63770 7840/8192 Checkheaps
    Mwe 00acfd7d 01b6b824 013e3250        623 01b69ad0 3476/8192 Quack process
    Mwe 00b2a260 01b6dad4 013e3250         22 01b6bbf0 7364/8192 Session Manager
    Mwe 00c55efd 01b78564 031d0478          4 01b74a50 14768/16384 uauth
    <--- More --->
    Mwe 00be3c9e 01b7aaec 0135c010          0 01b78b28 7524/8192 Uauth_Proxy
    Mwe 00c52759 01b80e0c 01361770          0 01b7ee88 7712/8192 SMTP
    Mwe 00c3f7b9 01b82eec 01361710          0 01b80fa8 7412/8192 Logger
    Mwe 00c3fd26 01b8502c 013e3250          0 01b830c8 7492/8192 Thread Logger
    Mwe 00f62272 01b9596c 013ac520          0 01b939c8 7188/8192 vpnlb_thread
    Msi 00b4097c 01c598c4 013e3250        190 01c578f0 8000/8192 emweb/cifs_timer
    Msi 005bd338 017a909c 013e3250      25855 017a7108 7412/8192 arp_timer
    Mwe 005c76bc 01b486e4 013fba50      20643 01b46770 7348/8192 arp_forward_thread
    Mwe 00c5a919 023fa5fc 013619e0          0 023f8648 7968/8192 tcp_fast
    Mwe 00c5a6e5 023fc624 013619e0          0 023fa670 7968/8192 tcp_slow
    Mwe 00c754d1 0240d42c 013628a0          0 0240b478 8100/8192 udp_timer
    Mwe 0019cb17 01b404a4 013e3250          0 01b3e530 7984/8192 CTCP Timer process
    Mwe 00efe8b3 0308c15c 013e3250          0 0308a208 7952/8192 L2TP data daemon
    Mwe 00efef23 0308e194 013e3250          0 0308c230 7968/8192 L2TP mgmt daemon
    Mwe 00eea02b 030c62ac 013a5c10         43 030c2338 16244/16384 ppp_timer_thread
    Msi 00f62d57 030c82f4 013e3250        264 030c6360 7924/8192 vpnlb_timer_thread
    Mwe 001b96e6 01b7cbbc 01b1e9c8          1 01b7ac48 7728/8192 IPsec message handler
    Msi 001c9bac 01b8d4dc 013e3250       2917 01b8b548 7648/8192 CTM message handler
    Mwe 00af93b8 031465b4 013e3250          0 03144640 7984/8192 ICMP event handler
    Mwe 00831003 0314a724 013e3250        387 031467b0 16100/16384 IP Background
    Mwe 0021b267 031a83c4 013123c0         31 03188450 123488/131072 tmatch compile thread
    Mwe 009f2405 03290044 013e3250          0 0328c0c0 16072/16384 Crypto PKI RECV
    Mwe 009f305a 03294144 013e3250          0 032901e0 16040/16384 Crypto CA
    Mwe 0064d4fd 01b3e24c 013e3250          8 01b3c2f8 7508/8192 ESW_MRVL switch interrupt service
    <--- More --->
    Msi 00646f5c 032c134c 013e3250    3059378 032bf448 7184/8192 esw_stats
    Lsi 008cbb80 032dc704 013e3250          3 032da730 7908/8192 uauth_urlb clean
    Lwe 008afee7 034a0914 013e3250        197 0349e9b0 6636/8192 pm_timer_thread
    Mwe 0052f0bf 034a35ac 013e3250          0 034a1648 7968/8192 IKE Timekeeper
    Mwe 00520f6b 034a8adc 0132e2b0          0 034a4e38 15448/16384 IKE Daemon
    Mwe 00bf5c78 034ac7ac 01360680          0 034aa7f8 8100/8192 RADIUS Proxy Event Daemon
    Mwe 00bc32de 034ae79c 034dcbe0          0 034ac918 7208/8192 RADIUS Proxy Listener
    Mwe 00bf5e0f 034b099c 013e3250          0 034aea38 7968/8192 RADIUS Proxy Time Keeper
    Mwe 005aac4c 034b3154 013fb980          0 034b1250 7492/8192 Integrity FW Task
    M*  008550a5 0009fefc 013e33b0       3183 034e3b20 24896/32768 ci/console
    Msi 008eb694 034ed9d4 013e3250       2370 034ebc40 6176/8192 update_cpu_usage
    Msi 008e6415 034f7dac 013e3250       1096 034f5eb8 6124/8192 NIC status poll
    Mwe 005b63e6 03517d1c 013fbd10       1963 03515d78 7636/8192 IP Thread
    Mwe 005becbe 03519e4c 013fbcb0          3 03517e98 7384/8192 ARP Thread
    Mwe 004c2b36 0351befc 013fbae0          0 03519fe8 7864/8192 icmp_thread
    Mwe 00c7722e 0351e06c 013e3250          0 0351c108 7848/8192 udp_thread
    Mwe 00c5d126 0352008c 013fbd00          0 0351e228 7688/8192 tcp_thread
    Mwe 00bc32de 03a6982c 03a5ee18          0 03a679b8 7512/8192 EAPoUDP-sock
    Mwe 00266c15 03a6b614 013e3250          0 03a699e0 7032/8192 EAPoUDP
    Mwe 005a6728 01b27b94 013e3250          0 01b25c30 7968/8192 Integrity Fw Timer Thread
    -     -        -         -      47686621    -         -     scheduler
    -     -        -         -      51253819    -         -     total elapsed
    ------------------ show failover ------------------
    <--- More --->
    ERROR: Command requires failover license
    ------------------ show traffic ------------------
    inside:
    received (in 51429.740 secs):
    7749585 packets905087345 bytes
    67 pkts/sec17013 bytes/sec
    transmitted (in 51429.740 secs):
    10653162 packets10355908020 bytes
    40 pkts/sec201026 bytes/sec
          1 minute input rate 412 pkts/sec,  51803 bytes/sec
          1 minute output rate 475 pkts/sec,  522952 bytes/sec
          1 minute drop rate, 24 pkts/sec
          5 minute input rate 399 pkts/sec,  59676 bytes/sec
          5 minute output rate 483 pkts/sec,  503200 bytes/sec
          5 minute drop rate, 9 pkts/sec
    outside:
    received (in 51430.240 secs):
    10758403 packets10441440193 bytes
    42 pkts/sec203021 bytes/sec
    transmitted (in 51430.240 secs):
    7548339 packets872053854 bytes
    <--- More --->
    63 pkts/sec16037 bytes/sec
          1 minute input rate 479 pkts/sec,  523680 bytes/sec
          1 minute output rate 387 pkts/sec,  46796 bytes/sec
          1 minute drop rate, 3 pkts/sec
          5 minute input rate 485 pkts/sec,  503789 bytes/sec
          5 minute output rate 387 pkts/sec,  57681 bytes/sec
          5 minute drop rate, 2 pkts/sec
    _internal_loopback:
    received (in 51430.740 secs):
    1 packets28 bytes
    0 pkts/sec0 bytes/sec
    transmitted (in 51430.740 secs):
    1 packets28 bytes
    0 pkts/sec0 bytes/sec
          1 minute input rate 0 pkts/sec,  0 bytes/sec
          1 minute output rate 0 pkts/sec,  0 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 0 pkts/sec,  0 bytes/sec
          5 minute output rate 0 pkts/sec,  0 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Aggregated Traffic on Physical Interface
    <--- More --->
    Ethernet0/0:
    received (in 51431.740 secs):
    10758462 packets10640075825 bytes
    42 pkts/sec206042 bytes/sec
    transmitted (in 51431.740 secs):
    7548383 packets1029818127 bytes
    63 pkts/sec20023 bytes/sec
          1 minute input rate 485 pkts/sec,  537048 bytes/sec
          1 minute output rate 395 pkts/sec,  54546 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 485 pkts/sec,  511723 bytes/sec
          5 minute output rate 387 pkts/sec,  65495 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Ethernet0/1:
    received (in 51433.570 secs):
    7749780 packets1066328930 bytes
    67 pkts/sec20064 bytes/sec
    transmitted (in 51433.570 secs):
    10653359 packets10552787020 bytes
    40 pkts/sec205006 bytes/sec
          1 minute input rate 419 pkts/sec,  59621 bytes/sec
          1 minute output rate 480 pkts/sec,  533950 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 399 pkts/sec,  67618 bytes/sec
    <--- More --->
          5 minute output rate 482 pkts/sec,  511073 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Ethernet0/2:
    received (in 51434.730 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
    transmitted (in 51434.730 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
          1 minute input rate 0 pkts/sec,  0 bytes/sec
          1 minute output rate 0 pkts/sec,  0 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 0 pkts/sec,  0 bytes/sec
          5 minute output rate 0 pkts/sec,  0 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Ethernet0/3:
    received (in 51434.730 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
    transmitted (in 51434.730 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
          1 minute input rate 0 pkts/sec,  0 bytes/sec
          1 minute output rate 0 pkts/sec,  0 bytes/sec
    <--- More --->
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 0 pkts/sec,  0 bytes/sec
          5 minute output rate 0 pkts/sec,  0 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Ethernet0/4:
    received (in 51434.870 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
    transmitted (in 51434.870 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
          1 minute input rate 0 pkts/sec,  0 bytes/sec
          1 minute output rate 0 pkts/sec,  0 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 0 pkts/sec,  0 bytes/sec
          5 minute output rate 0 pkts/sec,  0 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Ethernet0/5:
    received (in 51434.870 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
    transmitted (in 51434.870 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
    <--- More --->
          1 minute input rate 0 pkts/sec,  0 bytes/sec
          1 minute output rate 0 pkts/sec,  0 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 0 pkts/sec,  0 bytes/sec
          5 minute output rate 0 pkts/sec,  0 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Ethernet0/6:
    received (in 51435.010 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
    transmitted (in 51435.010 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
          1 minute input rate 0 pkts/sec,  0 bytes/sec
          1 minute output rate 0 pkts/sec,  0 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 0 pkts/sec,  0 bytes/sec
          5 minute output rate 0 pkts/sec,  0 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Ethernet0/7:
    received (in 51435.010 secs):
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
    transmitted (in 51435.010 secs):
    <--- More --->
    0 packets0 bytes
    0 pkts/sec0 bytes/sec
          1 minute input rate 0 pkts/sec,  0 bytes/sec
          1 minute output rate 0 pkts/sec,  0 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 0 pkts/sec,  0 bytes/sec
          5 minute output rate 0 pkts/sec,  0 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Internal-Data0/0:
    received (in 51435.510 secs):
    18513901 packets11784250044 bytes
    25 pkts/sec229023 bytes/sec
    transmitted (in 51435.510 secs):
    18207269 packets11641332179 bytes
    19 pkts/sec226078 bytes/sec
          1 minute input rate 891 pkts/sec,  595715 bytes/sec
          1 minute output rate 863 pkts/sec,  588935 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 885 pkts/sec,  584035 bytes/sec
          5 minute output rate 870 pkts/sec,  580393 bytes/sec
          5 minute drop rate, 0 pkts/sec
    Internal-Data0/1:
    received (in 51436.010 secs):
    18207323 packets11641364184 bytes
    <--- More --->
    19 pkts/sec226076 bytes/sec
    transmitted (in 51436.010 secs):
    18513954 packets11784281987 bytes
    25 pkts/sec229022 bytes/sec
          1 minute input rate 855 pkts/sec,  575808 bytes/sec
          1 minute output rate 884 pkts/sec,  582339 bytes/sec
          1 minute drop rate, 0 pkts/sec
          5 minute input rate 869 pkts/sec,  578350 bytes/sec
          5 minute output rate 883 pkts/sec,  581924 bytes/sec
          5 minute drop rate, 0 pkts/sec
    ------------------ show perfmon ------------------
    PERFMON STATS:    Current      Average
    Xlates               0/s          0/s
    Connections         17/s          6/s
    TCP Conns            8/s          2/s
    UDP Conns            7/s          2/s
    URL Access           0/s          0/s
    URL Server Req       0/s          0/s
    TCP Fixup            0/s          0/s
    TCP Intercept        0/s          0/s
    HTTP Fixup           0/s          0/s
    <--- More --->
    FTP Fixup            0/s          0/s
    AAA Authen           0/s          0/s
    AAA Author           0/s          0/s
    AAA Account          0/s          0/s
    ------------------ show counters ------------------
    Protocol     Counter                     Value   Context
    IP           IN_PKTS                  168960   Summary
    IP           OUT_PKTS                 169304   Summary
    IP           TO_ARP                       61   Summary
    ------------------ show history ------------------
    ------------------ show firewall ------------------
    Firewall mode: Transparent
    ------------------ show running-config ------------------
    <--- More --->
    : Saved
    ASA Version 7.2(3)
    firewall transparent
    hostname ciscoasa
    enable password
    names
    interface Vlan1
    nameif inside
    security-level 100
    interface Vlan2
    nameif outside
    security-level 0
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    <--- More --->
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    passwd
    regex domain1 ".facebook\.com"
    regex domain2 ".fb\.com"
    regex domain3 ".youtube\.com"
    ftp mode passive
    access-list ACL_IN extended permit ip any any
    pager lines 24
    mtu inside 1500
    mtu outside 1500
    ip address 192.168.1.254 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-523.bin
    no asdm history enable
    <--- More --->
    arp timeout 14400
    access-group ACL_IN in interface outside
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout uauth 0:05:00 absolute
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    class-map type regex match-any DomainBlockList
    match regex domain1
    match regex domain2
    match regex domain3
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
    <--- More --->
      message-length maximum 512
    match domain-name regex class DomainBlockList
      drop-connection log
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:bb5115ea1d14ee42e7961ef0c9aaed86
    : end
    <--- More --->
    ------------------ show startup-config errors ------------------
    INFO: No configuration errors
    ------------------ console logs ------------------
    Message #1 : Message #2 : Message #3 : Message #4 : Message #5 : Message #6 : Message #7 : Message #8 : Message #9 : Message #10 : Message #11 : Message #12 : Message #13 : Message #14 :
    Total SSMs found: 0
    Message #15 :
    Total NICs found: 10
    Message #16 : 88E6095 rev 2 Gigabit Ethernet @ index 09Message #17 :  MAC: 0000.0003.0002
    Message #18 : 88E6095 rev 2 Ethernet @ index 08Message #19 :  MAC: 001f.9ee8.ffa1
    Message #20 : 88E6095 rev 2 Ethernet @ index 07Message #21 :  MAC: 001f.9ee8.ffa0
    Message #22 : 88E6095 rev 2 Ethernet @ index 06Message #23 :  MAC: 001f.9ee8.ff9f
    Message #24 : 88E6095 rev 2 Ethernet @ index 05Message #25 :  MAC: 001f.9ee8.ff9e
    Message #26 : 88E6095 rev 2 Ethernet @ index 04Message #27 :  MAC: 001f.9ee8.ff9d
    Message #28 : 88E6095 rev 2 Ethernet @ index 03Message #29 :  MAC: 001f.9ee8.ff9c
    Message #30 : 88E6095 rev 2 Ethernet @ index 02Message #31 :  MAC: 001f.9ee8.ff9b
    Message #32 : 88E6095 rev 2 Ethernet @ index 01Message #33 :  MAC: 001f.9ee8.ff9a
    Message #34 : y88acs06 rev16 Gigabit Ethernet @ index 00 MAC: 001f.9ee8.ffa2
    Message #35 :
    Licensed features for this platform:
    Message #36 : Maximum Physical Interfaces : 8        
    <--- More --->
    Message #37 : VLANs                       : 3, DMZ Restricted
    Message #38 : Inside Hosts                : Unlimited
    Message #39 : Failover                    : Disabled
    Message #40 : VPN-DES                     : Enabled  
    Message #41 : VPN-3DES-AES                : Enabled  
    Message #42 : VPN Peers                   : 10       
    Message #43 : WebVPN Peers                : 2        
    Message #44 : Dual ISPs                   : Disabled 
    Message #45 : VLAN Trunk Ports            : 0        
    Message #46 :
    This platform has a Base license.
    Message #47 :
    Message #48 : Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
    Message #49 :                              Boot microcode   : CNlite-MC-Boot-Cisco-1.2
    Message #50 :                              SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
    Message #51 :                              IPSec microcode  : CNlite-MC-IPSECm-MAIN-2.04
    Message #52 :   --------------------------------------------------------------------------
    Message #53 :                                  .            .                            
    Message #54 :                                  |            |                            
    Message #55 :                                 |||          |||                           
    Message #56 :                               .|| ||.      .|| ||.                         
    Message #57 :                            .:||| | |||:..:||| | |||:.                      
    Message #58 :                             C i s c o  S y s t e m s                       
    Message #59 :   --------------------------------------------------------------------------
    <--- More --->
    Message #60 :
    Cisco Adaptive Security Appliance Software Version 7.2(3)
    Message #61 :
    Message #62 :   ****************************** Warning *******************************
    Message #63 :   This product contains cryptographic features and is
    Message #64 :   subject to United States and local country laws
    Message #65 :   governing, import, export, transfer, and use.
    Message #66 :   Delivery of Cisco cryptographic products does not
    Message #67 :   imply third-party authority to import, export,
    Message #68 :   distribute, or use encryption. Importers, exporters,
    Message #69 :   distributors and users are responsible for compliance
    Message #70 :   with U.S. and local country laws. By using this
    Message #71 :   product you agree to comply with applicable laws and
    Message #72 :   regulations. If you are unable to comply with U.S.
    Message #73 :   and local laws, return the enclosed items immediately.
    Message #74 :
    Message #75 :   A summary of U.S. laws governing Cisco cryptographic
    Message #76 :   products may be found at:
    Message #77 :   http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    Message #78 :
    Message #79 :   If you require further assistance please contact us by
    Message #80 :   sending email to [email protected]
    Message #81 :   ******************************* Warning *******************************
    Message #82 :
    <--- More --->
    Message #83 : Copyright (c) 1996-2007 by Cisco Systems, Inc.
    Message #84 :                 Restricted Rights Legend
    Message #85 : Use, duplication, or disclosure by the Government is
    Message #86 : subject to restrictions as set forth in subparagraph
    Message #87 : (c) of the Commercial Computer Software - Restricted
    Message #88 : Rights clause at FAR sec. 52.227-19 and subparagraph
    Message #89 : (c) (1) (ii) of the Rights in Technical Data and Computer
    Message #90 : Software clause at DFARS sec. 252.227-7013.
    Message #91 :                 Cisco Systems, Inc.
    Message #92 :                 170 West Tasman Drive
    Message #93 :                 San Jose, California 95134-1706
    ciscoasa#   

  • Cisco asa 5505 with Router 881w Configuration Help

    Hello all,
    I'm having trouble setting up a second vlan to route to the internet. I have a Cisco ASA 5505 connected to my ISP(OUTSIDE) and a Cisco 881w (INSIDE) router in the back of my firewall. My vlan 10 with the network 192.168.5.1 255.255.255.0 works with pat, however vlan 15 that is on my 881w router does not route to the internet at all. I can only ping from 192.168.15.15 network to 192.168.5.1 I would like some advice on how can I make this set up work. Attached with this discussion is a picture of my topology.
    Thanks in advance.
    here are the show runs:
    Cisco ASA 5505 show run:
    ASA Version 8.3(1)
    names
    interface Vlan1
     no nameif
     no security-level
     no ip address
    interface Vlan5
     mac-address xxxx.xxxx.xxxx
     nameif OUTSIDE
     security-level 0
     ip address dhcp setroute
    interface Vlan10
     nameif INSIDE
     security-level 100
     ip address 192.168.5.1 255.255.255.0
    interface Ethernet0/0
     switchport access vlan 5
    interface Ethernet0/1
     switchport access vlan 10
    interface Ethernet0/2
    interface Ethernet0/3
     shutdown
    interface Ethernet0/4
     shutdown
    interface Ethernet0/5
     shutdown
    interface Ethernet0/6
     shutdown
    interface Ethernet0/7
     shutdown
    ftp mode passive
    clock timezone CST -6
    clock summer-time CDT recurring
    object network INTERNAL_LAN
     subnet 192.168.5.0 255.255.255.0
    object network PRIVATE_LAN_192
     subnet 192.168.15.0 255.255.255.224
     description PRIVATE_LAN_192
    access-list INSIDE_access_in extended permit ip any any
    access-list INSIDE_access_in extended deny ip any any
    access-list OUTSIDE_access_in extended permit ip any any
    access-list OUTSIDE_access_in extended deny ip any any
    pager lines 24
    logging enable
    mtu OUTSIDE 1500
    mtu INSIDE 1500
    ip verify reverse-path interface OUTSIDE
    ip verify reverse-path interface INSIDE
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    object network INTERNAL_LAN
     nat (INSIDE,OUTSIDE) dynamic interface
    object network PRIVATE_LAN_192
     nat (INSIDE,OUTSIDE) dynamic interface
    access-group OUTSIDE_access_in in interface OUTSIDE
    access-group INSIDE_access_in in interface INSIDE
    route INSIDE 192.168.15.0 255.255.255.224 192.168.5.2 1
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    dhcpd dns 8.8.8.8 75.75.76.76
    dhcpd address 192.168.5.10-192.168.5.100 INSIDE
    dhcpd enable INSIDE
    Router 881w show run:
    Current configuration : 4912 bytes
    version 12.4
    no ip source-route
    ip dhcp excluded-address 192.168.15.1 192.168.15.10
    ip dhcp pool PRIVATE_LAN
       network 192.168.15.0 255.255.255.224
    interface FastEthernet0
     switchport trunk allowed vlan 1,15,1002-1005
     switchport mode trunk
    interface FastEthernet1
    interface FastEthernet2
    interface FastEthernet3
    interface FastEthernet4
     ip address 192.168.5.2 255.255.255.0
     duplex auto
     speed auto
    interface wlan-ap0
     description Service module interface to manage the embedded AP
     no ip address
     arp timeout 0
    interface Wlan-GigabitEthernet0
     description Internal switch interface connecting to the embedded AP
    interface Vlan1
     no ip address
    interface Vlan15
     ip address 192.168.15.1 255.255.255.224
    no ip forward-protocol nd
    ip route 0.0.0.0 0.0.0.0 FastEthernet4
    no ip http server
    ip http authentication local
    ip http secure-server

    The cable modem does not have any configuration. I cant add any to it. Its a cisco dpc3008. From vlan 10 i have no problem to get to the internet with the above  configuration. My problem is just vlan 15.

  • How to sync clock of Cisco ASA 5505 from NTP Server on internet

    Hi there!
    i've setup a site, with cisco ASA 5505. It has public ip also.
    i want to sync the clock of firewall from on ntp server on internet, or with internal domain controller that is inside LAN.
    The firewall has public IP also.
    how can i do this?
    Regards!

    Hello Lasandro,
    This should do it!
    http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/basic_hostname_pw.html#wp1236530
    Looking for some Networking Assistance? 
    Contact me directly at [email protected]
    I will fix your problem ASAP.
    Cheers,
    Julio Carvajal Segura
    http://laguiadelnetworking.com

  • How to configure VPN with Cisco ASA 5505 behind Actiontec MI424WR

    I'm trying to test my Cisco VPN client from my workplace to my home where I have a Cisco ASA 5505 (VPN server) behind the Actiontec MI424WR.  I'm able to Ping the Actiontec external IP.  I also have Port Forwarding for IKE and IPSec configured on the Actiontec, but I cannot establish the VPN connection.
    What do I need to configure on the Actiontec to make this work?
    Also, when I test this at home, the MI424WR acts as the DHCP server for my laptop and the Cisco outside interface.  At home, I'm able to establish the VPN connection from my laptop to the ASA, allowing me to see a shared drive behind the ASA.  However, at home, I cannot go to the Internet while using the VPN client.
    Thanks for any help.
    Steve
    Solved!
    Go to Solution.

    http://www.dslreports.com/faq/verizonfios/3.0_Networking
    those are the best sample config's and resources on how to set the FiOS network
    Bridging is possible but difficult.  That link will give you great info on it.
    Are you a FiOS customer that has phone/internet/tv
    or no tv?   or no phone?    You have to be careful on your configuration or you might lose some TV features and functionality, like the Interactive Program Guide, or the VOD or the Widgets.
    Sorry the Portforwarding wasn't enough to resolve your issue, I am not sure that it's a Actiontec config you are looking for, from my understanding of Cisco's and FiOS it may be something behind the cisco that is causing an issue.  You may want to reach out to the Cisco admin that manages that, and find out if there are additional ports that are required and then you can come back and configure those ports too.

  • Cisco ASA 5505 Reset-I Problem with TCP State Bypass

    Hello,
    I have a Cisco ASA 5505 that functions as my primary firewall and a Mitel 5000 controller behind it. I have two external phone users that have been connecting through the firewall with no issues for six months until about two weeks ago. I am now seeing the following log entry on the phone trying to connect to the Mitel Controller.
    6
    May 16 2014
    14:52:52
    302014
    72.135.115.37
    6915
    192.168.20.2
    6801
    Teardown TCP connection 1203584 for outside:72.135.115.37/6915 to inside:192.168.20.2/6801 duration 0:00:00 bytes 0 TCP Reset-I
    My phones are designed to work with the Mitel 5000 and Mitel 3300 phone controllers. The 5000 will only use port 6800 for call control, while the 3300 will use 6801 (Secured Minet), 6802 (Minet SSH), and if those fail, port 6800 (Minet Unsecured). When the phones initiate a connection, they try 6801 first. If 6801 is unavailable, the phone controller adds the RST flag to the ACK packet. When the phone sees the RST flag, it is supposed to reset and use the next port (6802). The same process happens again for port 6802, then the phone knows to try 6800. The problem is that the ASA sees the RST flag now and terminates the connection at the firewall. Therefore, the phones never see the RST flag, and continue to try the connection with port 6801.
    I have tried to use the TCP State Bypass feature to correct the situation, but the log shows that the connection is still being terminated immediately by the firewall. I am a novice when it comes to configuring the ASA. Any help would be greatly appreciated, as the company that I bought the phone system from is out of troubleshooting options. I do not think that I have made any changes to the firewall around this time. I have packet captures and logs from my ASA and I have wireshark data on the inside of my network. I need to figure out how to configure the ASA so that it ignores the RST flag and sends the packet back to the source.
    Any help would be greatly appreciated!

    Thanks Rizwan,
    Still no luck.  I can't even ping the otherside (office)..  I am not sure if i'm running the debug rightway.   Here are my results...
    homeasa(config)# ping inside 10.10.5.254............. (Office CIsco ASA5505 IP on local side.  I also tried pinging the server on other side (office) whic is @10.10.5.10 and got the same result)
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 10.10.5.254, timeout is 2 seconds:
    Success rate is 0
    homeasa(config)# debug crypto isakmp 7
    homeasa(config)# debug crypto ipsec 7
    homeasa(config)# sho crypto isakmp 7
                                       ^
    ERROR: % Invalid input detected at '^' marker.
    homeasa(config)# sho crypto isakmp
    There are no isakmp sas
    Global IKE Statistics
    Active Tunnels: 0
    Previous Tunnels: 0
    In Octets: 0
    In Packets: 0
    In Drop Packets: 0
    In Notifys: 0
    In P2 Exchanges: 0
    In P2 Exchange Invalids: 0
    In P2 Exchange Rejects: 0
    In P2 Sa Delete Requests: 0
    Out Octets: 0
    Out Packets: 0
    Out Drop Packets: 0
    Out Notifys: 0
    Out P2 Exchanges: 0
    Out P2 Exchange Invalids: 0
    Out P2 Exchange Rejects: 0
    Out P2 Sa Delete Requests: 0
    Initiator Tunnels: 0
    Initiator Fails: 0
    Responder Fails: 0
    System Capacity Fails: 0
    Auth Fails: 0
    Decrypt Fails: 0
    Hash Valid Fails: 0
    No Sa Fails: 0
    Global IPSec over TCP Statistics
    Embryonic connections: 0
    Active connections: 0
    Previous connections: 0
    Inbound packets: 0
    Inbound dropped packets: 0
    Outbound packets: 0
    Outbound dropped packets: 0
    RST packets: 0
    Recevied ACK heart-beat packets: 0
    Bad headers: 0
    Bad trailers: 0
    Timer failures: 0
    Checksum errors: 0
    Internal errors: 0
    hjnavasa(config)# sh crypto ipsec sa peer 96.xxx.xxx.118
    There are no ipsec sas
    homeasa(config)#

  • Cisco asa 5505: No traffic lan to wan with IPv6

    Hello everybody,
    I have a Cisco ASA 5505, public ipv6 in outside interface, private ipv6 in LAN, from router I can ping any ipv6 in Internet and ping my LAN ipv6. Traffic doesn't go through router.
    This is my configuration.
    interface Vlan1
     nameif inside
     security-level 100
     ip address PRIV-Saturn1 255.255.255.0
     ipv6 address fc00::1/7
     ipv6 enable
    interface Vlan2
     nameif outside
     security-level 0
     ip address PUBLIC26 255.255.255.248
     ipv6 address xxxx:yyyy:67:36::2/64
     ipv6 enable
     ipv6 nd suppress-ra
    access-list Dynamic_Filter_ACL extended permit tcp any6 any6
    ipv6 route outside ::/0 xxx:yyyy:67:36::1
    Am I omitting anything?
    Thanks in advance for the help.
    Jos P

    Since you're using IPv6 private addressing (fc00::) on the inside, you need a dynamic NAT entry to translate your private IPv6 addresses to a public one.
    Alternatively, you could just use a subnet of your registered IPv6 block for the inside network and not worry about NAT.

  • Azure Site to Site VPN with Cisco ASA 5505

    I have got Cisco ASA 5505 device (version 9.0(2)). And i cannot connect S2S with azure (azure network alway in "connecting" state). In my cisco log:
    IP = 104.40.182.93, Keep-alives configured on but peer does not support keep-alives (type = None)
    Group = 104.40.182.93, IP = 104.40.182.93, QM FSM error (P2 struct &0xcaaa2a38, mess id 0x1)!
    Group = 104.40.182.93, IP = 104.40.182.93, Removing peer from correlator table failed, no match!
    Group = 104.40.182.93, IP = 104.40.182.93,Overriding Initiator's IPSec rekeying duration from 102400000 to 4608000 Kbs
    Group = 104.40.182.93, IP = 104.40.182.93, PHASE 1 COMPLETED
    I have done all cisco s2s congiguration over standard wizard cos seems your script for 8.x version of asa only?
    (Does azure support 9.x version of asa?)
    How can i fix it?

    Hi,
    As of now, we do not have any scripts for Cisco ASA 9x series.
    Thank you for your interest in Windows Azure. The Dynamic routing is not supported for the Cisco ASA family of devices.
    Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site.
    However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as
    demonstrated in this blog:
    Step-By-Step: Create a Site-to-Site VPN between your network and Azure
    http://blogs.technet.com/b/canitpro/archive/2013/10/09/step-by-step-create-a-site-to-site-vpn-between-your-network-and-azure.aspx
    You can refer to this article for Cisco ASA templates for Static routing:
    http://msdn.microsoft.com/en-us/library/azure/dn133793.aspx
    Did you download the VPN configuration file from the dashboard and copy the content of the configuration
    file to the Command Line Interface of the Cisco ASDM application? It seems that there is no specified IP address in the access list part and maybe that is why the states message appeared.
    According to the
    Cisco ASA template, it should be similar to this:
    access-list <RP_AccessList>
    extended permit ip object-group
    <RP_OnPremiseNetwork> object-group <RP_AzureNetwork>
    nat (inside,outside) source static <RP_OnPremiseNetwork>
    <RP_OnPremiseNetwork> destination static <RP_AzureNetwork>
    <RP_AzureNetwork>
    Based on my experience, to establish
    IPSEC tunnel, you need to allow the ESP protocol and UDP Port 500. Please make sure that the
    VPN device cannot be located behind a NAT. Besides, since Cisco ASA templates are not
    compatible for dynamic routing, please make sure that you chose the static routing.
    Since you configure the VPN device yourself, it's important that you would be familiar with the device and its configuration settings.
    Hope this helps you.
    Girish Prajwal

  • Cisco Asa 5505 and Layer 3 Switch With Remote VPN Access

    i got today a new CISCO LAYER 3 Switch .. so here is my scenrio
    Cisco Asa 5505
    I
    Outside  == 155.155.155.x
    Inside  =      192.168.7.1
    VPN POOL Address =   10.10.10.1   -   10.10.10.20
    Layer 3 Switch Config
    Vlan 2
    interface ip address =  192.168.1.1
    Vlan 2
    interface ip address =  192.168.2.1
    Vlan 2
    interface ip address =  192.168.3.1
    Vlan 2
    interface ip address =  192.168.4.1
    Vlan 2
    interface ip address =  192.168.5.1
    ip Routing
    So i want My Remote Access VPN clients to access all this Networks. So Please can you give me a helpfull trick or Link to configure the rest of my routing
    Thank You all

    When My Remote VPN is Connected , it reaches 192.168.7.2 of the Layer 3 VLan that's Connected to The ASA 5505 ,
    But i can't reach the rest of the VLAN - example
    192.168.1.1
    192.168.1.2
    192.168.1.3
    192.168.1.4
    192.168.1.5
    But i can reach the Connected Interface Vlan to My ASA ..
    So here i think iam miss configuration to my Route
    Any Help Please this is urgent

Maybe you are looking for

  • How do I share my docs, pics, music from my iMac with macBook Pro?

    New Apple user...finally ditched Microsoft. I have an iMac and macBook Pro. I want to share all my files between the two so any changes will reflect on both machines. I don't quite know how to get the information into iCloud. I use to use Google Driv

  • Resolution problems with Samsung monitor

    I recently purchased a Samsung Syncmaster 19" TV/monitor for use with my MacBook while at university. The monitor's resolution is 1440x900, and my macbook correctly chooses this resolution when plugged in. My understanding was that when using a large

  • Throws Exception - a newcomer...

    I have written a small amount of code that takes information from a text file and displays it in a GUI (swing) - this is called my RasterDisplay class. However, I am now creating another part of the GUI which will have a button that makes a new Raste

  • Using Changed Data

    Hi, I implemented CDC without error and started the journal. My table name to be journalized: DWH_SEC_TYPES In the J$DWH_SEC_TYPES table and JV$DDWH_SEC_TYPES view, the changed data can be viewed. Also there is another view named JV$DWH_SEC_TYPES whi

  • Work Flow - SC Approval.

    Hi All, We are on SRM 5.0, The WF is not working... Reasons 1. when I create a SC, it is not trigerred for approval process. I also activated the WF WS 10000129 ( one step )& its following event TS 10008000. When When I check the Approval preview in