Trying to print from my iMac to a Cannon MG5320 will not print. Started having problem when new Wifi router??? was installed Cisco. Keep getting A Communication Error

Problems printing form iMac to Cannon MG 5320. Just had new Cisco router installed and problem started. Keep getting communication error

To address this problem, I suggest that you do a complete reinstall and setup of the printer as if it were brand new. It is preferable to do this from the original CDs that came with the printer. I think the printer has to set up again to connect to the new router.
The Canon web site has for this printer a "mini-master setup" file you can download that has the same setup program that came on the CDs.
http://usa.canon.com/cusa/consumer/products/printers_multifunction/photo_all_in_ one_inkjet_printers/pixma_mg5320?selectedName=DriversAndSoftware

Similar Messages

HP Photosmart c4450 prints and scans normal 8.5x11 fine, but will not print 4x6 laminate pictures.

HP Photosmart c4450 prints and scans normal 8.5x11 fine, but will not print 4x6 laminate pictures. Using the printer completely unconnected from a pc or network, using a SSD memory card to print off. As the printer begins the print, the printer prints only about 3/4 of the image, and clips the rest leaving it blank. Within the options, you can see the whole picture on the LCD screen, and selecting the 4x6 print mode it still clips the picture.
Not sure exactly whats going on, the printer was doing this fine for about a year, and just randomly started to print with the image cut off at the beging and ending abruptly at the end only printing half-3/4's. Also using the same memory card, have not tried a different card though. Any ideas?

As far as I know, you cannot scan or perform software-based copying over a Bluetooth connection. Printing is doable. Perhaps that is something that is in the pipe for developement.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

I am trying to update my iPhone software but to do so I needed to update iTunes. When I try to do that, I keep getting this error message" "There is a problem with this Windows Installer Package. A program required for this install to complete could not

I am trying to update my iPhone software but to do so I needed to update iTunes. When I try to do that, I keep getting this error message" "There is a problem with this Windows Installer Package. A program required for this install to complete could not....

Try the following user tip:
"There is a problem with this Windows Installer package ..." error messages when installing iTunes for Windows

My MG5320 will not print. The paper comes out but without printing.

My MG5320 will not print. Paper comes out but not printing.

Hi ts and andrea711,
We recommend performing at least one cleaning and two deep cleanings on the printer to try and get the ink to appear on the page. To do this, please follow the steps located at the link below:
Print Head Cleanings
If blank pages still come out of the printer after performing the cleanings, please call or email us at one of the methods on the Contact Us page for further assistance.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

My iMac (OS 10.9.2) will not print in color to my brother MFC_9340CDW

Hello,
I have a 27" iMac running OS X 10.9.2 that I can not get color prints from. I have a Brother MFC_9340CDW
I've printed color in the past. I've searched and searched for solutions but most have directions to things that don't apply
or that i can't find. Help me get my printing capabilities back?
Thank you for your help
MJ

Check the ink cartridges...
Open System Preferences > Printers & Scanners then select the Print tab.
Click: Options & Supplies the click Supply Levels.
If the color supply levels are ok, reset the print system > OS X Mavericks: Reset the printing system

Photosmart 6520 e Windows 7 printer says it is connected to network, but will not print.

I've followed all suggestions in troubleshooting both from manual and on line. Shut off firewall, unplugged, plugged waited. Nothing changes. All printouts from the printer say connected, but will not print and computer detection of the printer says cannot be located. Help!!

Glad you were able to find the problem. I am sure that the Print and Scan Doctor would have come to the same conclusion Thanks for sharing what the cause was...I am sure others will benefit from it if they also have this issue.
If I have helped in any way, just click the Kudos star on the left. Also, if your issue has been resolved, don't forget to select Accept as Solution

Firefox will not start and open a website from a Thunderbird email link. It will go to a link from Thunderbird once Firefox is open, but will not initially start Firefox and proceed to open the Thunderbird email link.

Firefox will not ''start'' and open a website from a Thunderbird email link. A link from Thunderbird will open once Firefox is ''already'' started, but will not initially start Firefox and proceed to open the Thunderbird email link.

I also have this problem. I cannot open links from a discussion board I frequent nor can I open links from my email. Also after opening my email, I cannot go to any other sites except my home page. I can then go no where else.
When I close Firefox and try to reopen it, it does nothing! I have to bring up the Task Manager and end the Firefox process before I can get back in.
To the best of my knowledge, this problem started with the new update to Ver. 3.6.9. I am running Windows XP Media Center 2005

My printer is showing on my computer, but it will not print.

Printer is showing on devices and with registered address, but will not print. I am using an HP laptop.

Hi pandros;
I hope you are doing well and welcome to the HP forum,
Is virtually impossible to provide any asisitance wit hte information provided, I am eager to do my best to help you.
I will strongly recommend you to read this post and repost your question accordingly CLICK HERE.
This will increase the chances of me as well as other in the forum to help you. Repost after reading this post and I will do my best of assist you.
Regards;
RobertoR
You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

How do i print from an imac (lion) to a windows 7 shared printer?

I have been struggling to get my imac to print to a windows 7 (64bit) shared printer. my other windows machines work just fine. the imac finds it as a shared printer but then it just sticks at spooling with 82 bytes in the queue at the windows machine. i have searched around and tried all the options suggested but have got no further. Apple support wont help (its a new imac).

At last after much searching (i see i am not alone !) i found the best solution to my problem;
insert USB stick
copy file to usb stick
remove usb stick
insert usb stick in windows 7 machine
print file.
crazy and stupid i know but i really cant be bothered trying to find another solution
i had been led to believe apples just worked clearly not the case!
no please dont tell me this is a windows issue as it is not!
windows and linus machines print to the shared printer just fine.

Print only allows to save as All Files* - will not print .pdf

Had Reader 9, now 10. Received document, saved as .pdf. Attempted to print this .pdf, but when click Print, document needed to be saved again, but was only giving me format as All Files* to save in. Still did not print. Have checked all Printer settings -still won't print. Conflict in 9 and 10? Do I need to somehow reinstall 9 - as that was working?

Vielen Dank -
but why would the advanced tab change as I never had changed that feature in other .pdf s . Is it default with 10?
Usually the printer shows - Print to file, and allows me to change the format, whether as a .docx, .jpeg or .pdf, but that option wasn't available.
Technology is changing too fast for me to catch up and master!!!!

I just tried updating my iPhone to ios 6. It told me that I need to restore my iphone and update it but I keep getting the -1 error

I just tried updating my iPhone 4 to ios 6. It told me that I need to store my phone and update it but every time I try to update it, I get the -1 error message...can someone help me out?

Sorry, wish I could help but I have the same problem.
Been trying for hours to update a 4s and the furthest I get is the "-1" error.
So frustrating, I guess a visit to Apple is forthcoming.
Been using the iPhone since the first model and never a problem till now.
John

HT4356 Frontier installed Super Fios and I cannot print from iPad to my airprinter as it will not connect to same network now Any suggestions

My Internet was changed to Fios and Frontier installed a new router with different Essig and wep key. How do I connect my air printer to wifi. My iPad is using same SSID AND PASSWORD AND CONNECTS TO NEW ROUTER BUT NOT MY PRINTER. EPSON ASKS FOR VALUE. NOT SURE WHAT IS TO BE ENTERED FOR THAT. TRIED WEP KEY. ESSIG NO AND. PASSWORD USED FOR WIFI NAME ON IPAD. NO LUCK.
MHAS ANYONE HAD TROUBLE WHEN UPGRADING WITH FRONTIER HIGH SPEED INTERNET. CAN FRONTIER GIVE ME THE NEW SSIG AND PASSWORD

Uwdawgfan-
Your new router may not correctly handle Bonjour data required by AirPrint. Contact Frontier to correct the router's setup. A firmware update may be required.
Fred

I can't print from my mac to a cannon IR 4235 UFRII Print Driver

How do i connnect to a canon IR 4235 UFRII print driver from my mac?

What happens when you try to connect to it?

C309A PRINTER GIVES FALSE "OUT OF PAPER" MESSAGE AND WILL NOT PRINT WHEN TRYING TO PRINT ENVELOPES

When trying to print an envelope, I get an error message - "out of paper" and cannot proceed.

Hi novalani,
This could be as simple as dirty feed rollers but could require servicing in the end. See this article for feed problems. Give the steps a shot and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Trying to upgrade from Elements 10 to 11 on mac will not install.

Elements 10 works fine.
downloaded upgrade for elements 11 both photoshop and premiere. neither one will install.
it startsm and fails and says to run adboe support advisor. I have, it says no errors.
please let me know how to correctly update and install elements 11 over elements 10
thanks

If the Adobe Support Advisor was unable to locate the error then please manually review your installation logs. You can find details on how to accomplish this at Troubleshoot with install logs | CS5, CS5.5, CS6 - http://helpx.adobe.com/creative-suite/kb/troubleshoot-install-logs-cs5-cs5.html.

Trying to print from my iMac to a Cannon MG5320 will not print. Started having problem when new Wifi router??? was installed Cisco. Keep getting A Communication Error

Similar Messages

Maybe you are looking for