Trying to set up Time capsule..."OS status error -50" error received

Hi,
I was trying to set uip my time capsule recently but it would not work, my wireless hard drive is set up for windows PC and also configured for my Macbook thru the Buffalo software, but when setting it up on my mac it will not complete the procedure and I receive this error message "OS status error -50", can anyone help me?
Cheers
Paul

+but once formatted, could I partition it, and have a half for the time machine? and put the rest on the other half?+
If you are talking about an external drive attached directly to your computer, yes, that should work fine. The general rule of thumb for Time Machine backups is that you will want to reserve at least 2 times the amount of space that your current Mac is using now to allow for a good "history" of future incremental backups.
So, if the HD on your Mac is using 200 GB, then you would want to reserve at least 400-500 GB of space for Time Machine backups, and more if you can.
It's not possible to partition the Time Capsule disk unless you physically remove it and place it in a separate enclosure. I would not advise this, as for starters, this would void the warranty. It is possible to create a "disk image" on the Time Capsule disk that will in effect accomplish the same task as a partition. Post back if you need more info on this.
Message was edited by: Bob Timmons
Message was edited by: Bob Timmons

Similar Messages

Trying to set up time capsule but keep getting message stating airport utility was unable to find any airport wireless device. What do I do know?

Trying to set up my time capsule on my imac.
Keep getting message "Airport utility was unable to find any airport wireless devices."
What do I do now?
joglenn

When having difficulties accessing the Time Capsule (TC) via the AirPort Utility, try the following, in order checking accessibility with the utility after each step:
Check the local connection. If you are trying to access the TC wirelessly, make sure that you are connected to its wireless network before running the AirPort Utility to administer it. If you are still unable to access it with the utility, temporarily connect your computer directly using an Ethernet cable to one of the TC's LAN ports.
Power cycle the base station. Remove the power adapter's plug from the power outlet, and then, wait 15 seconds before plugging it back in.
Perform a "factory default" reset on the base station.
Finally, if you are attempting to access the TC via an Ethernet connection, be sure that your Ethernet port is NOT configured for Jumbo Frames, i.e., using an MTU of 9000+.

Trying to set up time capsule with airport exteme. Apple advises to use manuel setup and click on Advanced. Then enter mobileme ID. I did this but Time Machine doesn't display anything on the capsule window.

Can't set up my time capsule on Airport Extreme (updated). Apple instructions are to use manual set up. Click on Advanced tab. Click on Mobileme and enter Mobileme ID and password. I did this. But Time Machine window is blank. Tryed to click on update window after entering Mobileme ID but Airport does not respond (turn of then on)

mickair wrote:
I have been experiencing some networking problems
Welcome to Apple's discussion groups.
I have the latest Time Capsule ("TC"), an old Airport Extreme Base Station ("AEBS") bought in 2007 and 2 Airport Expresses, one bought in 3 months ago ("AE-Alpha") and the other bought back in 2007 ("AE-Beta"). All of them have been updated with the latest firmware.
Based on those dates, the AirPort Extreme is probably flat (as opposed to dome-shaped), making it 802.11n-capable. The Newer AirPort Express is probably an 802.11n-capable model A1264, while the older one is probably a model A1084 or A1088.
I use {the TC's} DHCP function ... to avoid unauthorized use.
This a discussion for another thread, but that's not what DHCP is for.
The wireless setting for it is to participate as WDS Main, but after reading various posts, it seems WDS is a bad idea
With that older AirPort Express you're stuck with WDS unless you decide to replace it with a newer model.
The AEBS is currently setup as being a WDS Relay at the moment
Why a relay? That's only needed if there's another base station "beyond" it that is configured to depend on it.
Since the AEBS is connected to the TC via Ethernet, you should probably configure it as a "roaming network":
http://discussions.apple.com/thread.jspa?threadID=2273124
{The AE-Alpha} connects fine as WDS remote at the moment
I don't have any experience with mixed WDS and non-WDS networks, but since it's 802.11n-capable, you may be able to configure it to "extend" the network of the TC rather than as WDS. Look for a setting on the TC to "Allow this network to be extended".
Physical location:
AEBS in one end, TC and AE-Alpha in the middle while AE-Beta on the other end.
A device such as "AE-Beta" that's supposed to extend a network shouldn't be "at the end" but should be half way between the central base station and the clients that need an extended network.

Trying to set up Time Capsule for WiFi access with Linksys router

Problem: I must use a Linksys router to connect to internet, since I have my telephone connected to this router (Vonage). I have set up a Time Capsule and connected it to the Linksys router, which is NOT wireless. I would like to use the wireless capability of the Time Capsule to provide wifi connection for laptop computers. The Time Capsule's wireless network is visible to these computers, but they do not connect to the network, since the Time Capsule is not the source of dynamic IP addresses; rather, the Linksys router is the source for IP addresses on my network. What must I do to get IP addresses supplied to computers attached via wifi?

The Time Capsule was set up using bridge mode. My initial error was to use the WAN port. After switching to a LAN port to connect with the Linksys router, the laptop computer was able to connect to the network wirelessly, but it could not obtain web page from the internet.
The laptop is a Dell Inspiron 6000; with an ethernet cable attached to the Time Capsule, it receives an IP address AND it can obtain web pages from the internet. The command "ipconfig /all" issued at the DOS prompt yields approximately the following:
Broadcom... (this is the ethernet card) ... IP address 192.168.15.104, with the gateway 192.168.15.1 (which is the Linksys router)
Intel(R) PRO/Wireless... (this is the wireless card) ... IP address 192.168.15.103, with the same gateway.
I can ping the iMac from the Dell laptop; the iMac is connected directly to the Linksys router. Running ping 192.168.15.104 from Terminal on the iMac succeeds, while ping 192.168.15.103 does not.

Trying to set up Time Capsule to MacBook Air but it only recognises the ethernet LAN connection and not the WAN Any ideas?

If I put the ethernet cable in the WAN port of the capsule my book doesn't pick it up but when I put it in the LAN one it does. Then it tells me it needs the WAN connection I tried rebooting in various ways including modem but I can't get past 2 problems i.e. Problem1 - Double NAT so I click the Bridge Mode and then it asks me to place the cable in the WAN port. As soon as I do it loses it. The light is flashing amber so its clearly a connection problem. Any ideas anyone?

The WAN port is for the ethernet cable that is coming straight from your modem/router.
Plug your computer into any of the Lan ports.
Once you're configured (and in bridge mode) it won't matter after that, but leave those details for later.

Set up time capsule as wireless access point

I am trying to set up my old apple time capsule as a wireless access point for my girlfriend. She is at college and the university does not permit routers, so I am trying to set the time capsule up so that is just takes the hardwired internet and allows wireless access to the internet so she can use her iPad and MacBook Air on the wireless instead of having to use a gigabit adapter to use the ethernet. The time capsule has the newest firmware and she is running mavericks which has the newest airport utility software. However I am not sure what settings to use to make this work. I am fairly intelligent when it comes to computers however I am not very skilled in networking. If anyone can help I would greatly appreciate it.
Thank you in advance!

How old is the Time Capsule? Running what firmware?
You have a problem.. If you cannot use the TC in router mode, then you are going to have to use it in bridge.. and it then depends on if the Uni system will hand out mulitple IP addresses. .which I doubt. In the end you might be stuck.. and it is not possible really with any system..
Bridge normally requires that the TC take an IP address and then clients connecting to the TC wireless will also get IP addresses.. but if the uni system only hands out one address then the TC has already captured it and there are no more available.. but try that method first.. as it is the easiest.
If it fails there is a more complicated method.. where we can give the TC a separate static IP in a different IP range and the wireless will still be bridged.. so the MBA or the ipad can use the wireless.. but only one can ever be online at a time.
The only way around this is to use the TC as a router contra the rules in the uni.. although I would suggest the uni only cares if you break their system. Most people don't.. but I am unsure what happens if you do.
Ask their IT people how to use a wireless only device like ipad, when they only provide ethernet. You might find there already is a wireless internet system as well.

HT1175 I am trying to setup my Time capsule via a ethernet cable as a back up for a new iMac. The on button on the time capsule set up window keeps failing to stay on. Any ideas what to do?

I am trying to setup my Time capsule via a ethernet cable as a back up for a new iMac. The on button on the time capsule set up window keeps failing to stay on. Any ideas what to do?

A PC can have more issues connecting than a Mac.
But it really should not matter.. so just try it in situ.. press and hold the reset.. once it starts up, it will return to default IP, 10.0.1.1 the PC should then be able to find it via the airport utility.
If not drag it over to the Mac and plug in there by ethernet.. or since it is a laptop, really should not be that difficult to drag the Laptop and plug it into the TC.
Important thing is to get access to the TC.
The Mac if it is running lion, then you MUST download and install 5.6 airport utility to do anything useful.
http://support.apple.com/kb/DL1482

Trying to set up time machine but it does not show my disc plugged into airport. Time capsule setup never shows disc .

Trying to set up time machine but cannot get it to find my disc plugged into Airport.

I hate to have to tell you this, but backing-up that way is unreliable and not supported by Apple. See: Using Time Machine with an Airport Extreme Air Disk.

Having trouble setting up Time capsule...

I just bought a new iMac last night. I also picked up Time Capsule and Apple TV. I'm having a problem setting up Time Capsule correctly. I'll go through what I did step by step and hopefully someone can help me as I've never tried to set up a wireless network before.
I'm connected to the internet via Comcast. I have the outside cable coming into the modem and the ethernet cable from the modem i have plugged into TC's WAN port (the one with the gear logo).
I start by opening Airport Utility ( I upgraded to the most recent version using the install disc that came with TC) and it recognizes TC in the left side of the window. It says it found TC with default settings and gives a name for it and an Airport ID. I click continue.
The next window prompts me to name the TC and assign a password. I do so and click continue.
The next window gives me some options about setting up a new or existing wireless network. It says it found some existing networks which I assume are my neighbors. I select "I don't have a wireless network and want to create one". I click continue.
The next window prompts me to give a name and security level to the new network. I provide a name and select WPA/WPA2 Personal and enter and verify a password. I click continue.
The next window asks whether I'd like TC to be in Bridge mode or Share a single IP address using DHCP and NAT.
If I click Share a single IP, a popup tells me "This will cause my TC to continue to blink amber and do I want to ignore this and continue?". So I figure this can't be a good thing and I click on Bridge mode not really knowing what it means.
The next window asks me to enter the TCP/IP info from my ISP. It also says to choose "Using DHCP" if I receive an IP address automatically. So in the box where it says "Configure IPv4", I select "Using DHCP" and there is an IP address and Subnet mask with numbers after each. Below that is Router Address, with fields for DNS Server, Domain Name and DHCP Client ID. These fields are blank. I click continue.
The next window says TC will use these settings:
TC name - Jim's Time Capsule
Wireless Mode - Create a wireless network
Network Name - Jim's Network
Wireless Security - WPA/WPA2 Personal
Connect Using - Ethernet
Configure IPv4 - Using DHCP
IP Address - (Provided Automatically)
If settings are correct, click Update to finish setting up your TC or click Go Back to change settings. I click Update and a box tells me that the device and its network service will be temporarily unavailable and do I want to continue? I click continue.
The next window tells me that the settings for TC have been updated successfully and its being configured. I then get a window reporting a problem.It says-
"Problem 1 of 1: Internet Connection
Your Apple wireless device does not have a valid IP address. Make sure your Apple wireless device is connected to your broadband modem or local network, verify your settings and try again. If you still can't connect, call your ISP."
There are two boxes with options. The first is "Connect Using" and "ethernet" is selected with "PPoE" being the other option. The second box says "Configure IPv4" and "Using DHCP" is selected, and "Manually" is the other option.
Obviously, I'm doing something wrong, but I don't have a clue. I'm getting online fine when I plug the ethernet cable into the back of the iMac. I've reset the modem by hitting the reset button. The light turns green on the TC but I can't connect to the internet. Any ideas? Feel free to call me a big dummy
Jim

Thank you, Jim Somoygi. I had a similar multi-hour odyssey with a AE and a Comcast cable modem.
This solved the seemingly endless blinking amber light:
1. unplug power from the modem and AE (or time capsule). Go get a beverage of your choice (wait a couple of minutes).
2. My modem has a battery backup (Comcast phone service). So, I pressed a tiny reset button on the back of the Comcast modem (it's made by Arris). With the battery backup, I'm not sure I would have been able to reset the modem simply by unplugging.
3. Make sure there is an ethernet cable connecting the cable modem and the AE or TC
4. Plug the modem back in, wait for the lights to come on. I also had to press a "standby" button on the front of the modem to get all the lights to come on.
5. Plug in the AE (or TC)
6. Green light on the AE (it's not easy being green)
7. Choose the appropriate Airport network & surf away.
I will say that the problem seems to be with the modem, rather than the AE. Once I reset the modem, I could configure the AE with ease. Once the AE is configured, it is absolutely rock stable. Before I fiddled with the network & brought this on myself, I enjoyed shockingly stable networking with the AE -- much better than with previous attempts with Netgear or Buffalo products (although I do like the ease with which Buffalo products can be configured together, using their proprietary handshaking protocol "AOSS").

Setting up Time Capsule for backup only on existing wireless network

I have a wireless network already set up with a NetGear wireless router. Cable plugs into router, router connected via ethernet cable to my Power Mac G5 desktop, plus 2 PC laptops in the house also connect wirelessly to the home network via this router.
I want to set up Time Capsule as an external hard drive to back up all three computers -- I don't necessarily need to use it as a wireless router although i'm not opposed to that if it's easier to do it that way.
When i try to set it up using AirPort utility, i get the amber flashing light. Airport utility is able to discover the device, and then always asks if it's OK to switch networks. I've tried both "switch" and "don't switch"; either way when i try to set it up, AirPort utility stalls out on "Reading Time Capsule Configuration"; eventually giving me the error msg: "Base Station Error: AirPort Utility was unable to find your Apple wireless device."
All i want to do is mount it as an external hard drive so i can use Time Machine for backup, and be able to use it to also back up the PC laptops wirelessly. I need help in the following three areas:
1. How should I be physically connecting my devices if i want to do this? Which cables go in which ports? There is only one ethernet port on the back of my G5. The G5 can connect to the router either wirelessly OR via ethernet cable. I've tried G5-->Time Capsule-->Router, G5-->Router-->Time Capsule, Router-->G5 PLUS Router-->Time Capsule, and I've tried every variation on the regular ethernet and WAN ports. What's the right way to do this.
2. If i'm not setting up the TC as a Wireless Router, is AirPort utility even the right tool for setting it up? it seems to be confused by the two wireless networks and won't let me get past that point. Am I supposed to click "Switch" when it asks me to switch networks? Is there a way to just mount it as an external drive and bypass the AirPort utility setup entirely?
3. Once i get it set up so it's visible as an external drive and usable for Time Machine backup, how do i then make it available to the other PCs on the network so they can back up to it also?
Thanks for your help.

sarah,
You already have an existing wireless network.
You do not need to plug the Time Capsule into anything except power.
Set the Time Capsule to "Join an existing wireless network"...
That is all you need to do.
Then all the computers should see the Time Capsule.
If you can't see "Join an existing wireless network" in the choices, hold down on the option key and then click on the choices.
Give that a try.

Trying to connect Airport time capsule to my leopard iOS mac. Downloaded software for time capsule for snow leapard/leopard but still says I need more software. What do I need?

Trying to connect Airport time capsule to my leopard iOS mac. Downloaded software for time capsule for snow leapard/leopard but still says I need more software. What do I need? I have a 10.5.7 iOS (Leopard). It connects to wifi at speeds in the airport and has plenty of storage capacity and memory.

If your Time Capsule looks like this..
Please review the System Requirements to set up and administer the device.....
Setup and Administration
iPhone, iPad, or iPod touch with iOS 6 or later and AirPort Utility 1.3
Mac with OS X Lion v10.7.5 or later and Airport Utility 6.3 or higher
http://www.apple.com/airport-time-capsule/specs

How do i set my time capsule up to function as an external hard drive

How do i set my time capsule up to function as an external hard drive? Is this even possible? I had a friend tell me it woudl be a good set up to get a time capsule with my Macbook Air to use as a gigantic external hard drive but then was unbale to wlak me through the setup after I bought the equipment. Any suggestions?

It depends on what you already have equipment wise..
Just bridge the TC..
I cannot walk you through it either if you use v6 airport utility.. due to my refusing to run Lion until it gets network issues sorted.
Download and run the real utility http://support.apple.com/kb/DL1482
Go to manual setup..
Internet tab
Connection sharing.. select off bridge mode in the drop down box.
You can then if you like turn off wireless under airport wireless.. The TC is now a plain network client with hard disk.
Personally I would keep the wireless on but sort the channels manually if you already have a wireless AP or router.

How to set up time capsule with BT home hub 4.0 & Openreach

Idiots guide needed.
My TimeCapsule (year old model) had been running well from my BT Openreach box (without using the Home Hub 4.0) but recently had issues with connection dropping - BT said they've sorted out their end and can't see any remaining issues and can't offer me any more support if I'm not using the Home Hub 4.0
I reset the TC to run straight from the Openreach Box still have issues with wi-fi dropping in and out (both on ethernet and wi-fi).
Can I:....
1) set up Time Capsule running from BT Home Hub 4.0 which itself runs from BT Openreach white box (thus continuing to get support from BT)
or should i go back to
2) Time Capsule running straight from BT Openreach Box
Can some one post an idiots guide to either option?
Other stuff that may be important.
Macbook air running Yosemite (mid 2011 model)
Apple TV
Airportexpress
Time Capsule
2 x iphone 4s
Kids PC
Ethernet and wifi for above - I generally run everything hard wired via ethernet.

The easiest and sure way is to use bridge on the TC as the method of connection. The TC then becomes a device in your network and gets its IP from the main router that I presume BT supply.
Method is,
1. Plug the TC WAN port into the BT supplied modem by ethernet.
2. Plug the computer you are using for the setup into the TC by ethernet.
3. Run the airport utility .. go to internet tab on the top menu..
In the bottom option, Connection Sharing choose off (bridged mode)
4. Go to the wireless page and setup wireless connection as you like it.. using whichever band you want. And make sure security is set to the highest setting, wpa2 personal. Put in a decent wireless passkey.
5. Press the update and fix whatever else the TC will show as needing fixing.. usually security stuff.
6. You can then disconnect the ethernet and connect by wireless if you want. Any port on the TC will now be a LAN port, including WAN.
This is assuming BT supply a wireless router with built in vdsl/other type of modem. If so you normally will not be able to bridge the modem, unless BT are using pppoe authentication which they haven't in the past.
If you really need to use the TC as a router then you will need to work out an alternative method. You can double NAT by placing the TC in the DMZ of the BT router if that is an option. It is not without issues in general.

HOW TO SET UP time capsule with time machine?

I have not been successful in setting up time capsule with the time machine,can someone give me steps to follow?

What part are you having problems with? You need to make sure File Sharing is enabled on the Time Capsule (which is done in AirPort Utility). Then you just connect to the Time Capsule either wirelessly or via ethernet cable and when you go to Time Machine setup your computer should recognize your Time Capsule as a valid storage for Time Machine backups.

How to set up time capsule with BT Infinity

how to set up time capsule with BT Infinity

The easiest and sure way is to use bridge on the TC as the method of connection. The TC then becomes a device in your network and gets its IP from the main router that I presume BT supply.
Method is,
1. Plug the TC WAN port into the BT supplied modem by ethernet.
2. Plug the computer you are using for the setup into the TC by ethernet.
3. Run the airport utility .. go to internet tab on the top menu..
In the bottom option, Connection Sharing choose off (bridged mode)
4. Go to the wireless page and setup wireless connection as you like it.. using whichever band you want. And make sure security is set to the highest setting, wpa2 personal. Put in a decent wireless passkey.
5. Press the update and fix whatever else the TC will show as needing fixing.. usually security stuff.
6. You can then disconnect the ethernet and connect by wireless if you want. Any port on the TC will now be a LAN port, including WAN.
This is assuming BT supply a wireless router with built in vdsl/other type of modem. If so you normally will not be able to bridge the modem, unless BT are using pppoe authentication which they haven't in the past.
If you really need to use the TC as a router then you will need to work out an alternative method. You can double NAT by placing the TC in the DMZ of the BT router if that is an option. It is not without issues in general.

Trying to set up Time capsule..."OS status error -50" error received

Similar Messages

Maybe you are looking for