Trying to use HPLJ 1102w as a wired network printer. How do you configure the network settings?

I have an HPLJ 1102W and I want to use it as a wired printer on my LAN. The trouble is, the easy setup utility is geared toward wireless networking and the ethernet interface will not get a DHCP address from the LAN. In order to get an IP address, I have to go through the wireless networking configuration settings. Can anyone point me in the right direction on how to use this printer as a wired network printer?
thanks,

Hi,
The HP LaserJet P1102w provide USB or wireless network interface only.
the product do not include any ethernet card, as you may also find by its spesification System Requirements below:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01999607&tmp_task=prodinfoCategory&cc=us&dlc=en...
Connectivity: Hi-Speed 2.0 USB port / Wireless 802.11 B/G (P1102w only)
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Similar Messages

How do you configure the iMac so separate users can access each other's files, especially iPhoto and iTunes? I need to be able to transfer media between two users and not just gain limited access using 'share'.

How do you configure the iMac so separate users can access each other's files, especially iPhoto and iTunes? I need to be able to transfer media between two users and not just gain limited access using 'share'.

See Terence Devlin's thorough explanation here.

I am unable to use my own network with my iphone for wi-fi.The message says "unable to join the network (my network). How do I configure the info in the phone to allow me access?

How do I configure the setting in my iphone to allow me use of my own network?

Thanks for the responses, they have been very illuminating!
This is very disappointing from The Carphone Warehouse. If they had mentioned this when I went into their stores, I wouldn't have completed the purchases. I bought two phones at separate outlets and neither of them told me this.
I have been in contact with T-Mobile already as I thought they had sneakily applied a software update that locked the phone. They have denied locking it and suggest that it is something that Apple do. Their solution was a factory reset.
I have a call logged with Apple this afternoon, so will see what they suggest. Hopefully they will give me something that I can take to The Carphone Warehouse or T-Mobile.

I just set up a wireless network using an airport express. How can you change the network name

How can you change the name of a wireless network set up with an airport express

Yes, you can. If you use the current AirPort Express, Apple says that you can connect up to 50 devices. Realistically, make that 25-30 or so before the speed really begins to drop.
Remember that you will have to reset the modem though, before you connect it to the AirPort Express as the modem "remembers" the settings for your computer.

How do you configure the set of port to use for FTP passive data connection

I was able to start the ftp server xml db and connect to it locally. When I tried to connect to it from home, I was able to log in but when i do a "get" command the sessions hangs. I also tried passive mode and do a "get" command and it gives me a connection refused error. I am using the default port 2100. I think this might be a firewall issue with the data connection port. I am not sure which range of ports to open for the passive ftp connection on the server side or where to go and set them for for the ftp server to use? Or this issue might not be firewall related??? Any thoughts. Thanks.

This is a typical problem with VPN/Firewall software and FTP on ports other than 21.
When you open the FTP data connection the FTP Server identifies which port the data will be sent on using the PORT command which is sent on the command port (typically 21 with a normal FTP server, 2100 by default with XDB). THe client then opens that PORT to accept the data (file, output of an ls etc).
As I understand it most VPN/Firewall are configured to monitor 21 for 'PORT' requests. They then understand to allow connection on the PORT number passed on the command PORT. Hence with Port 21 firewall / VPN software is not a problem. However since the XDB command PORT is something other than 21 they do not see / honour the PORT commands from the server and hence the client cannot open the data connection on the specified PORT
As to how to solve it, I wish I knew (After 5 years I still can't use XDB FTP from home to a machine in the office once the VPN tunnel is open :( ). I'm sure it's going to be firewall / VPN software specific and may need the VPN servers to be configured.
The best bet would be to run the FTP server on 21...
Add the following line to your listener.ora file
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP) (HOST = hostname) (PORT = 21))
(PROTOCOL_STACK = (PRESENTATION = FTP) (SESSION = RAW)))
and then restart the listener as root
Start the listener as root.
At the operating system prompt, enter tnslsnr with optional command line arguments. The usage is as follows:
tnslsnr [listener_name] [-user user] [-group group]
where:
Table 4-3 tnslsnr Utility Options
Option Description
listener_name
Specify the name of the listener. If omitted, the default name LISTENER will be used.
-user user
Specify the user whose privileges the listener will use when super user (root) privileges are not needed. After performing the privileged operations, the listener will give up root privileges irreversibly.
-group group
Specify the group whose privileges the listener will use when super user (root) group privileges are not needed. After performing the privileged operations, the listener will give up root group privileges irreversibly.
The listener will temporarily switch to the provided user and group immediately after startup. All subsequent operations will be done with the specified user and group privileges, except the system calls necessary to listen on configured endpoints. The listener will revert to super user (root) for a short period of time to listen on reserved addresses, such as TCP ports less than 1024. After the listener starts listening on all of its endpoints configured in listener.ora, it will switch to the specified user and group irreversibly. Therefore, the listener will give up the root privilege that it initially had. In the current release, -user and -group command line arguments only accept user and group identifiers specified in numeric form.
For example, to execute a root listener called mylsnr and have it use privileges of a user identified

In Iphoto, using a MacBook when looking at a slideshow, how do you turn the music down or temporarily off?

When viewing photos in IPhoto, using a slideshow, how do you turn down the music or just turn it off? Thank you.

This answer applies to iPhoto '09 version 8.1.2 (424)
The mute button on the keyboard and the volume control buttons are still active during a slideshow.
Or you can uncheck the 'play music' option in the Slideshow settings and the slides will play with no sound.
If you have a linked Apple Remote and are using it to play the slideshow, the plus and minus buttons also control volume.

Same question for the "2 iPhones in one account".....How do I change the name. My iPhone is showing my wife's iPhone name when I am syncing it. Why is that? I know about using one iTunes account....But how do you change the name w/o erasing your data?

Hi....How do you change the name? When I sync my iPhone, it shows my wife's name on it?

Unfortunately it is not doing it....
Let me give more details..We have 3 iPods and 2 iPhone4....I recently purchased the iPhone4 and when we connected it..It was already reading my wife's iPhone4..We went to the Apple Store at the Grove today and was told to de-authorize the system and connect my iPhone4 back and I should be able to change the name.
Nothing happened..Right now, I clicked on RESTORE settings...and it is uploading a new iPhone update.

How do i configure the usb port on a draytek vigor 2820n router for use with my imac

i have an imac connected to the internet through a draytek vigor 2820n router. this router has a USB port with a HP Deskjet 5560 printer attached (for use as a network printer for other machines on the network). How do I configure this printer on the iMAC?

I checked on the HP web site. Your aswer is on the HP website under your printer type. Update your drivers and follow the instructions given by HP and the printer will work as you have it connected.
Good Luck

I created a Pages document inserting 2 columns using 1) Inspector 2) Layout 3) columns. How do I decrease the height of the column. Have tried to use cursor and drag down the top border, but that does not reset the top border.

I created a Pages document inserting 2 columns using 1) Inspector 2) Layout 3) columns. How do I decrease the height of the column. Have tried to use the cursor and drag down the top border, but that does not reset/decrease the top border.

Set your columns back to one for the moment. In layout mode, insert a Text box. Place it in the upper left corner of your document, and drag down and right to the size of the container for your two columns. Click inside the Text Box, and now bump up your columns to 2. Your two columns are now contained in this resizable Text Box.

I have not used my CS3 version for about 3-4 years. I tried to use it recently and I get a message about activation. Called the phone number recommended but no longer in use. How do I start using MY version I paid for? Using PC

I have not used my CS3 version for about 3-4 years. I tried to use it recently and I get a message about activation. Called the phone number recommended but no longer in use. How do I start using MY version I paid for? Using PC

Can you activate CS3. If you lost your serial you can retrieve it from Adobe.com. Sign in at Adobe.com the use this link https://www.adobe.com/account/my-products-services.html When your Adobe Product list is displayed click on your CS3 product your serial number should be displayed.

I´ve just changed my apple id password, and when trying to use Facetime, after having entered such new password, it won´t fullfill the calls, nor can I receive incoming calls, it simply gets disconnected. What do I do??

I´ve just changed my apple id password, and when trying to use Facetime, after having entered such new password, it won´t fullfill the calls, nor can I receive incoming calls, it simply gets disconnected. What do I do??

iOS: Troubleshooting FaceTime
Unable to make or receive FaceTime calls after April 16, 2014
Using FaceTime and iMessage behind a firewall
iOS: Troubleshooting FaceTime and iMessage activation
iOS: Using FaceTime
FaceTime, Game Center, Messages: Troubleshooting sign in issues

I just tried to use my iphone as modem for my laptop but once i select the iphone at my network connections it ask me for my password, does anybody knows if that information is either my iphone serial number, fcc id, IC, etc

i just tried to use my iphone as modem for my laptop but once i select the iphone at my network connections it ask me for my password, does anybody knows if that information is either my iphone serial number, fcc id, IC, etc

If you are trying to connect via wifi to our iPhone then the password should be displayed on your phone when you go into Personal Hotspot, by default it is a random password set by the phone but you can change it there.

How do I configure Guest network to access ethernet wired printer?

I have a wired/wireless network with a new dual band AEBS. The AEBS is connected to a Cisco router, which in turn sends it's connections to various wall-plates in our home. One HP 4110 printer is wired via it's ethernet port, one Mac Mini (OS 10.6.2) is hard wired also. The dual band AEBS 5 GHz network is used for our newer laptops, and the 2.4 GHz network is used for a G3 Firewire PowerBook (now don't make fun... it was the best there was at one time) running OS 10.4.11.
The PowerBook cannot access the printer that is hard wired via ethernet cable to the network. How do I get the PowerBook on the "Guest" network to access the printer?
I tried searching these discussions, but can't find an answer to my specific issue. Any help is appreciated.

Since you have a simultaneous dual-band AEBS, why not connect your PowerBook G3 to the non-Guest 2.4 GHz network created?
Can I take an AEBS that is a couple of years older (I have a couple of the flying saucers around here somewhere), wire that to an available ethernet port on the LAN, and then connect the older PowerBook G3 to that older AEBS wirelessly?
Sure
If so, will that arrangement slow down the entire system?
No
If that won't work, and I connect the PowerBook G3 directly to an ethernet port, will that slow down the other wireless computers?
Yes you can connect your PowerBook G3 via Ethernet. That would have no effect on the wireless computers.

HT3382 I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter. How do I configure the computer so that it doesn't sleep when I close the lid of the computer.

I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter. How do I configure the computer so that it doesn't sleep when I close the lid of the computer.

Hi alangium,
Welcome to the Support Communities!
Resetting your computer's PRAM should restore your Macbook Pro's screen appearance.
OS X Mavericks: Reset your computer’s PRAM
http://support.apple.com/kb/ph14222
This article may provide some information about your Mini DisplayPort to AVI adapter. Have you tried to connect a different VGA monitor to your Macbook to see if you get the same results?
Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
http://support.apple.com/kb/HT3382
18. What is the maximum resolution available for use with the Apple Mini DisplayPort to VGA adapter?
The resolution available with the Apple Mini DisplayPort to VGA Adapter is 1920 x 1200. VGA displays that use higher refresh rates (such as 85 Hz) at resolutions of 1600 x 1200 or greater may not generate video properly until you lower the refresh rate.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/HT1573#5
How can I detect displays?
If the detect displays option is not available, hold down the Option key while you are in the Display pane.
How do I select additional resolutions on my display?
You can use the Display pane of System Preferences to specify how your display works. Not all options appear for all display models. By default the best resolution for your display will already be selected in System Preferences.
To select a different resolution, use the Scaled option. Some additional resolutions may be available when you hold the Option button.
I hope this information helps ....
- Judy

No longer use this email account but how do you backup the email that is...

No longer use this email account but how do you backup the email that is in the "example" folder, So that I can delete the account on my mail app?

Not sure what you mean. Deleting a POP account only deletes the messages stored in the account’s mailboxes, not any messages stored in custom “On My Mac” mailboxes, if that’s what you mean. It’s not that Mail goes after your mail trying to delete as much as it can. It’s just that if a mail account is deleted, then its mailboxes cannot exist anymore...
That said, instead of deleting the account right away, you can just disable it (i.e. turn OFF Preferences > Accounts > Advanced > Enable this account), leave it that way for some time, and delete it only after making sure you didn’t miss anything while the account was disabled.
BTW, if you back up your data, and the ~/Library/Mail folder in particular, you won’t have to worry about accidentally losing anything as a result of doing something like that...
Note: For those not familiarized with the ~/ notation, it refers to the user’s home folder. That is, ~/Library is the Library folder within the user’s home folder, i.e. /Users/username/Library.

Trying to use HPLJ 1102w as a wired network printer. How do you configure the network settings?

Similar Messages

Maybe you are looking for