TS1363 when I plug in my IPOD into my computer to add more songs, my computer, nor itunes recognizes the IPOD.
i can know longer see my IPOD connected to my computer. My IPOD is functioning fine... even can play on my docking system. Trying to add more songs.
try a different usb port, or try the wall charger, change ipod usb wire, turn ipod on to see if the low battery screen pops up by holding onto the switch above the ipod. try that stuff
Similar Messages
-
When I plug my iPhone 4s into my PC, I get a message that says iTunes needs a newer version of Apple Mobile Device Support. It wants me to uninstall both the AMDS and iTunes and then reinstall iTunes. iTunes won't recognize my phone and so I can't synch it. Has anyone else run into this problem recently and how did you resolve it? Thanks!
Thank you both. I suppose I should have prefaced my question with the concern that I've read a number of other posts from people who have had a similar issue and when they tried to follow the directions, they ran into a multitude of other problems. As you might imagine, I'm hoping to avoid the creation of new problems as I try to solve this one. Thanks again.
-
My PC is not recognizing one of our 2 iPod gen4/5 and I'm trying to upload CDs not sold by iTunes onto the iPod. How do I get this done. Thanks for your help
See these for Windows.
iTunes 7 doesn't recognize the iPod.
Your Windows PC doesn't recognize iPod.
iPod appears in Windows Explorer but does not appear in iTunes.
iPod does not appear in iTunes.
Fast user switching in Windows XP is not supported.
Strange iPod behavior.
And these for Mac.
iPod doesn't appear in iTunes or on the Mac desktop.
iPod does not appear in iPod Updater or iTunes in Mac OS X.
iPod appears on the Mac OS X desktop but not in iTunes.
Try to restore it in disk mode.
Putting iPod into disk mode. -
I have more music in my iTunes library than I want on my iPod touch. The solution used to be simple: I simply check off the albums etc. that I want to sync. Now when I do that it goes through all the sync motions but nothing really happens. The same music that was on the iPod stays there and but the songs I've selected to sync don't appear.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Why won't it recognize?
iCloud is free, iTunes match is $25 a year.
I had the same problem and when I went to Settings I had 0 songs, even though they were obviously still there since I only had 15GB free on my 64GB device.
I decided to do a complete reset/restore of my 4th gen iPod Touch, Bad move! I've been messing with it for hours, and it simply won't restore--it keeps hanging on a black screen with an Apple logo and a progress bar at about 10%, sometimes it goes completely blank and tries again, with the same result. (I've posted my question/plea for help here: https://discussions.apple.com/message/19735862 )
I'm ready to bang my head against the wall! I can put the device in recovery mode, connect to iTunes on my computer, and get it back to the setup screen, but when I go through the process again and try to do an iCloud backup I get the same reset/restore loop.
I could start from scratch, but I really, really, really don't want to go through all of my hundreds of apps, reinstall them one by one, etc. etc. etc.
I thought that once I started using iCloud, I didn't need to sync with iTunes anymore--guess I was wrong. -
i have tried everything and nothing is working I have no idea how to delete it off of itunes manualy and I dont have the manage device option.
Find My iPhone Activation Lock: Removing a device from a previous owner’s account
For the future:
What to do before selling or giving away your iPhone, iPad, or iPod touch -
i loaded the newest version of itunes and now neither my windows 7 computer nor itunes recognizes my ipod
try a different usb port, try restarting the computer, and try reseting the ipod
-
Computer nor Itunes recognizes Ipod
While my Ipod was updating the usb was pulled out of the computer. My computer nor Itunes recognizes the Ipod Video (30gb) and my Ipod won't turn on either even when the hold button is off. If anyone knows how to deal with this thing. Please help (I have to go on a trip for Christmas Vacation).
Have you had a chance to look at these troubleshooting pages? They may be of some help:
iPod missing in My Computer and in iTunes
iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date -
What do you do when the computer won't recognize the ipod attached by the USB cord?
when I attach the USB cord to the computer it says that the device is not recognized. How do you fix that?
Can you try a different USB port?
Does iTunes recognize the iPod when connected under Devices? -
Hi, for some reason I can't add more music to my iPod and it doesn't give me the choice of choosing iTunes to show my iPod. I want to add more music but all it gives me the option to do it put pictures my computer. I really need help and I have no clue what to do. Please help me
Try using RecBoot to kick it out of recovery mode. If that does not work, try a manual install, as outlined in link below. If it STILL keeps entering recovery mode, you most likely need a new logic board.
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro 8G RAM 750G HD + OCZ Vertex 3 SSD Boot HD
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101 -
When I plug my ipod into my desk top my computer will not recognize the ipod in the usb port. I checked my usb port with one of my flash drives and it works fine. My ipod is in stuck in recovery mode, so has to be gone thru on itunes. Please help me
Yes, I think so... But what's odd here (to me) is that it actually matters what song the iPod was playing before being connected to that USB port. What happens if you connect the iPod when it is not playing any song? It seem like either the car audio system knows where to look for the iPod's song files, or it doesn't.
If you have a USB flash drive, try putting a few song files on it, and connecting it to that USB port. That's probably the primary reason for that USB port, so customer can attach USB flash drives with song files. If that works, and you can properly browse and play songs from the USB flash drive, you should just get a $5 8GB USB flash drive, fill it with your "car songs," and leaving it connected to the car audio system. That would be more convenient that remembering to connect and disconnect your nano all the time, and less wear-and-tear on the nano. -
I have a shuffle. When I plug it into Itunes, it tells me that it has not been ejected properly, and it will not recognize the Ipod. I have turned off the computer, and tried this with another shuffle with the exact same results. Any ideas?
Do you remeber the exact (or close to it) wording of the error message?
Try manually placing the iPod in Recovery mode and then try to restore
Next try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
You can also try another computer to help determine if you have an iPod or computer problem. -
Hello People!
I'm getting an error message when I plug my iPhone 4 into my computer. It says, "This iPhone cannot be used because the Apple Moblie Device Service has not been started." What does this mean? I've never had this error before. It's also giving the same message with my iPod touch. Please help!
Thanks,
DanaGalYou can easily check whether you've the Apple Mobile Device in your computer.
Right click 'My Computer' , then Manage => Services and Applications => Services. Apple Mobile Device is listed in alphabetical order. If none, it means you've not download iTunes into your computer yet. If yes, please ensure the Apple Mobile Device is in 'Started' status.
Good luck -
So when I plug my iPhone 3GS into my iMac, for music reasons, it says I have 123 songs. When I plug my iTouch into my iMac it says I have 565 songs on my iTouch. I have the same apple idea for both my iPhone and iTouch, how do I transfer my 565 songs on my iTouch to my iPhone? PLEASE HELP!!!
When you connect your iPad or iPod to the Mac, click on the device name in iTunes - don't click on the arrow on the device. Then click on the Music tab in the main window pane. Now you should see 'Sync Music' and all your playlists, artists and albums. Here you mark the checkboxes for what should be synced.
-
I got a new iphone and entered all my new information, but when i plugged my new phone into the computer with all my old information, it synced that information onto my new phone. is there any way to reverse it?
While that may work9I do not think it will) with iTunes purchased music it will not work for other music.
- Transfer iTunes purchases by:
iTunes Store: Transferring purchases from your iOS device or iPod to a computer
- For other music you will need a third-party program like one of those discussed here.
Copy music
Maybe you are looking for
-
Can I upgrade my processor from i3 350m to anything better?
Perhaps an i5? & What is the socket#? Because I've read that i3 and i5 have the same socket. Is this true? The lady on the phone from HP customer support said I cannot, but because of how she assisted me and answered other question I asked, it left m
-
Creation of referenc BP in SD for different company code from IS-U system
Dear Friends, I have two company codes called 2000 and 3000 in my IS-U system. I would like to create SD ref customer with reference to BP created in the IS-U system. I created SD reference customer with 2000 company code along with sales data's and
-
I'm using Acrobat 8 print to Apdobe PDF to create a pdf document, but it seems every .joboptions setting I use creates rasterized artwork. I am printing from a pdf form to pdf in order to be able to step and repeat. The source PDF form is using a vec
-
When trying to load a Mapping App on a website I am getting the following error: Unable to display MapSerice java.util.MissingResourceException: Cant find bundle for base name AppServer_Res, locale en_US for key: ReqestedServiceIsNotAvailableTemp in
-
Hot area around non-image link
I would like to make the area immediately around a box with a link (not an image) also clickable so that the user's cursor doesn't have to be directly upon the link for it to be 'hot' = how does one do that? Thank you.