TS1398 since i update my iphone4 to ios6 i have a problem with my wi-fi i never had this problems before .

since i update my iphone4 to ios6 i have a problem with my wi-fi i never had this problems before .

If it is grey and/or won't allow you to slide it to the on position, follow these steps... More than likely you will need to get it serviced.
iOS: Wi-Fi settings grayed out or dim
Follow these steps to resolve the issue:
Restart your iOS device.
Make sure that airplane mode is off by tapping Settings > Airplane Mode.
Reset the network settings by tapping Settings > General > Reset > Reset Network Settings.
This will reset all network settings, including Bluetooth pairing records, Wi-Fi passwords, VPN, and APN settings.
Make sure that your device is using the latest software. To do so, connect your device to your computer and check for updates in iTunes.
If you still can't turn Wi-Fi on, please contact Apple for support and service options. If you can turn Wi-Fi on but are experiencing other issues with Wi-Fi, see how to resolve those Wi-Fi issues.

Similar Messages

  • Since I updated 37.0.1 it started crashing every few minutes or so. I never had this case as far as I can remember

    it is just 2-3 days this is happening and happened after the latest Firefox update. I have FF on my system for few years and I haven't installed anything new. MY system restore shows only Chrome (from 41.0.2272.101 to .118) and Firefox (from 36.0.4 to 37.0.1) have been updated. Never experiences similar crashes. After few min or 1-2 hour, even staying in the few open tabs that I have had open for long time, it crashes. Two different behaviors. Sometimes shows me a window and asked to close or debug. Another time shows me a window that I can report the crash and restore the browser. Sometimes it also happens that as soon as I start it it crashes but mostly stays for while.

    We're sorry to hear that Firefox is crashing. In order to assist you better, please follow the steps below to provide us crash IDs to help us learn more about your crash.
    #Enter ''about:crashes'' in the Firefox address bar and press Enter. A Submitted Crash Reports list will appear, similar to the one shown below.
    #Copy the '''5''' most recent Report IDs that start with '''bp-''' and then go back to your forum question and paste those IDs into the "Post a Reply" box.
    ''' Note:''' If a recent Report ID does not start with '''bp-''' click on it to submit the report.
    (Please don't take a screenshot of your crashes, just copy and paste the IDs. The below image is just an example of what your Firefox screen should look like.)
    ;[[Image:aboutcrashesFx29|width=500]]
    Thank you for your help!
    More information and further troubleshooting steps can be found in the [[Firefox crashes - Troubleshoot, prevent and get help fixing crashes]] article.

  • I updated my iPhone 5 yesterday and it replaced ios6.2 with iOS 6.1 has anyone had this problem?

    I updated my iPhone 5 yesterday and it replaced ios6.2 with iOS 6.1 has anyone had this problem?

    You are confusing your iOSs...
    Today iOS 6.1 was released... replacing iOS 6.0.2

  • I am using Windows 7 Home Premium 64-bit OS.  I've never had this problem before... today I opened iTunes and it prompted me to download the newest version.  I use iTunes all the time and have updated it multiple times with no issues.  During the installa

    I am using Windows 7 Home Premium 64-bit OS.I've never had this problem before... today I opened iTunes and it prompted me to download the newest version.  I use iTunes all the time and have updated it multiple times with no issues.  During the installation process it gave me an error message that said: 
    Runtime error! 
    Program C:\Program Files\iTunes.exe
    R0634
    An application has made an attempt to load the C runtime library incorrectly.
    Please contact the application's support team for more information.
    I quit the installation, uninstalled iTunes and rebooted my computer.  I now receive a similar message with a slight difference:
    Runtime error! 
    Program C:\Program Files (x86)...
    R0634
    An application has made an attempt to load the C runtime library incorrectly.
    Please contact the application's support team for more information.
    I did not leave anything out from the error message.  It doesn't point to a specific file, it just ends with "(x86)..."  Every time I boot up my computer, this error message pops up on my desktop.
    How do I repair this issue?  I have found multiple suggested solutions but am unsure which one is the best, and I don't want to try a bunch of different things for fear I may make the problem worse.  I would like to try and fix this myself if possible but I need to know if that is really possible or if I need to take my computer to someone for repairs.  Any suggestions will be greatly appreciated!!

    Hi lustyln,
    I'm having a little trouble understanding all of what you are trying to explain. From what I can tell, it sounds like your PC has a lot of software problems and you want to know what is supposed to be there and what isn't.
    For reference, here are your product specifications:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01893242&lc=en&product=4043282
    To get your PC software back to how it was when it was first purchased, run a system recovery:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01867418&lc=en&product=4043282
    I hope this helps.
    ...an HP employee just trying to help where I can, but not speaking on behalf of HP.

  • I am trying to upload pictures to website, but get an error message saying that server redirection is not suppoerted. What is this, and why does it happen? I've never had this problem before and it started after Firefox update yesterday.

    Trying to upload pictures to a website, but it doesn't work. After going thru the whole process, I get a message saying; the server attempted to redirect you. Server redirection is not supported. This only happened after I updated Firefox. Never had this problem before.

    Dear Jody..jone5
    Good for you that can't update your iphone because I did it and my iphone dosen't work for example I can't download any app like Wecaht or Twitter..
    Goodluck
    Atousa

  • Has anyone else had a problem with data? after updating my phone to the new update, i have all this data, and keep getting notifications that my data is getting high. i never had this problem before.

    has anyone else had a problem with data? after updating my phone to the new update, i have all this data, and keep getting notifications that my data is getting high. i never had this problem before.

    fair enough.  No need for any unnecessary posts either.  You issue had been addressed ad nauseum already in this forum had you bothered to search this forum (as forum etiquette would dictate) before posting.
    In any case, I hope that your problem was solved.

  • HT5262 I've updated to iOS 6 and now my music wont play in my Audi - anyone else had this problem?

    I've updated to iOS 6 and now my music wont play in my Audi - anyone else had this problem?

    What do you mean by "on the days that should be marked"?  Are you calendar events displayed on the wrong days?

  • I am trying to add tracks which I have on my library on my computer to my ipad. I have done this manually but teh status bar never gets beyond "preparing to update". I have used itunes for years but never had this problem before

    I am trying to add tracks which I have on my itunes library on my pc to my ipad. I have done this manually but the status bar never gets beyond "preparing to update". I have used itunes for years but never had this problem before

    When I restart my iPad the connect to iTunes comes up and stays on until it shuts down again, I have read a report from Apple support suggesting I reinstall iTunes so I might try that again and also your suggestion which i shall also try, but thanks again - rg1547

  • IPad 2 problem. After updating to IOS 8.0.2 iPad says that I need to plug into iTunes. When I do that, the only option is to restore iPad to factory settings? iPad will do nothing until then. I have never had this problem before. Help

    iPad 2 problem. After updating to IOS 8.0.2 iPad says that I need to plug into iTunes. When I do that, the only option is to restore iPad to factory settings? iPad will do nothing until then. I have never had this problem before. Help

    Hi ..
    Follow Apple's instructions for recovery mode here >  iOS: Unable to update or restore
    You can restore from a backup.

  • After installing ios6 I now have app downloads stuck in waiting mode. I went to down in App Store but could not find a way to disable them. How can I do this. I never had this problem on ios5. I'm using an iPad 3

    After installing ios6 I now have app downloads stuck in waiting mode. I went to downloads in App Store but could not find a way to disable them. How can I do this. I never had this problem on ios5. I'm using an iPad 3

    Try downloading in iTune (computer) and sync to iPad.

  • I have been trying to update my software for the past 3 hours. It just goes so far and stalls. I've never had this problem before, what am I doing wrong?

    I have been trying to update my iPad2 for the past 3 hours. It just sets there doing very little and says its going to take 9 hours.  What am I doing wrong?  I've never had this problem before.  Also can I update from any other computer? Just in case it is my lap top.

    Do you get any error messages ? If you get a network timeout error when downloading the update then try temporarily turning off all your firewall and antivirus software until the download has completed.
    It's best to only update via your own computer, otherwise you risk losing all your iPad's contents - updating to iOS 5 wipes the iPad and then restores your backup. If you having problems downloading the update then you could try downloading the update file via a browser on another computer and then copying that file to your laptop for the actual update .

  • Frustratingly, since I upgraded to Yosemite 10.10, I too am having the worst problems with WiFi dropping out. I've never had this problem before on my iMac 27-inch mid 2011 model. Turning WiFi off and then back on again sometimes works. Help please.

    Frustratingly, since I upgraded to Yosemite 10.10, I too am having the worst problems with WiFi dropping out. I've never had this problem before on my iMac 27-inch mid 2011 model. Turning WiFi off and then back on again sometimes works. Help please. I've already tried a lot of your suggested fixes, but without success. Why hasn't Apple Fixed this?

    Please test after taking each of the following steps that you haven't already tried. Stop when the problem is resolved. Back up all data before making any changes.
    Step 1
    Take the applicable steps in this support article. The Wireless Diagnostics program generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
    Step 2
    Disconnect all USB 3 devices. If you don't know which are USB 3, disconnect all USB devices except keyboard and mouse.
    Step 3
    If you're not using a wireless keyboard or trackpad, disable Bluetooth by selecting Turn Bluetooth Off from the menu with the Bluetooth icon. If you don't have that menu, open the Bluetooth preference pane in System Preferences and check the box marked Show Bluetooth in menu bar. Test. If you find that Wi-Fi works better with Bluetooth disabled, you should use the 5 GHz Wi-Fi band. Your router may not support it; in that case, you need a new router.
    Step 4
    Open the Energy Saver pane in System Preferences and unlock the settings, if necessary. Select the Power Adapter  tab, if there is one. Uncheck the box marked
              Wake for Wi-Fi network access
    if it's checked.
    Step 5
    Open the Network pane in System Preferences and make a note of your settings in the Wi-Fi service. It may be helpful to take screenshots of the various tabs in the preference pane. If the preference pane is locked, unlock it by clicking the padlock icon and entering your administrator password. Delete Wi-Fi from the service list on the left by selecting it and clicking the minus-sign button at the bottom. Then recreate the service by clicking the plus-sign button and following the prompts.
    Step 6
    In the Wi-Fi settings, select
              Advanced... ▹ TCP/IP ▹ Configure IPv6: Link-local
    Click OK and then Apply.
    Step 7
    Reset the System Management Controller.
    Step 8
    Reset the PRAM.
    Step 9
    Launch the Keychain Access application. Search for and delete all AirPort network password items that refer to the network. Make a note of the password first.
    Step 10
    Make a "Genius" appointment at an Apple Store, or go to another authorized service center.

  • Music cuts out after a few seconds or goes straight back to menu since I downloaded iTunes 11. Never had this problem since I bought apple tv 2 years ago.

    Music cuts out after a few seconds or goes straight back to menu since I downloaded iTunes 11. Never had this problem since I bought apple tv 2 years ago.

    Welcome to the Apple Community.
    Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
    You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
    Refer to your router manual for instructions on changing your wifi channel.

  • Since yesterday my iphone 4 has started to freeze intermittently when unlocking.  When it happens nothing happens (left it for an hour last night) until I reset the phone, but it's done it 5 times today. Never had this prob before.   Any thoughts?

    Since yesterday my iphone 4 has started to freeze intermittently when unlocking.  When it happens nothing happens (left it for an hour last night) until I reset the phone, but it's done it 5 times today. Never had this prob before.   Any thoughts?

    I had the same problem (freezing iphone when trying to unlock) today.
    1) I made a backup of my iphone using itunes.
    2) Went to my service provider and made a sim swap. So, I think there was a problem with the nano simcard.
    Problem solved.

  • I recently downloaded the latest iTunes update and now my menus are in Korean. I work in Korea but want my menus in English. I've never had this problem with updates before. How can I get English back? Thank you.

    I recently downloaded the latest iTunes for Windows update, and now when I open iTunes my menus are in Korean. I live and work in Korea but want my menus in English like they always have been. I've never had this problem with updates before. How can I get English back? I'll appreciate any help.

    CTRL+, (Comma) brings up preferences
    General is the tab on the left
    Language is the last drop down control
    English (UK) & English (US) are 9th and 10th on the list
    Close iTunes & reopen to effect the change
    tt2

Maybe you are looking for

  • How to make use of StreamGobbler?

    Hi, I want to redirect the out and err statements to a file. I found a class called StreamGobbler at http://www.physionet.org/physiotools/puka/sourceCode/puka/StreamGobbler.java I dont know how to make use of it as I have almost no knowledge of Concu

  • Brazilian Calendar Problem - week should start on Sunday

    If a user selects Brazil/Portuguese as the international settings on the iPhone, everything works fine except the calendar. Here in Brazil, the first day of a week is allways on Sunday and not on Monday. (I can't imagine where Apple got this informat

  • BOM in CRM

    Hi  guys, I'd like to create in CRM something like BOM in R3 - main material and it's components. Could you please tell me what CRM functionality to use. I don't see any BOM transactions. May be it's possible to use relationships in these cases? Ther

  • Pisuper Authorization error, I can't logged with any user on Int Builder

    Hi SAP Guru's , Please help me as i new in SAP XI . I am unable to logged on in Integration Builder with any user i tried pisuper, sapuser but still got the same error "Authorization error, unknown username or password" . I check with T-Codo SU01 but

  • Where used for table fields

    I have list of 3600 fields , I need to get info related to these fields are used in which screens. Any easy way ? PS : Please donot suggest to use se11--> and make whereused list for field a®s Edited by: a®s on Jul 31, 2009 12:34 PM