TS1398 will not join with router

just got ipad out of box. tried connecting to my router but would not join only says, dismiss. standing next to router so no probs with signal strength. lap top and notepad connect wirelessly okay and i have checked security code stamped on the router. any thoughts for a complete novice?

Can see network?
Settings>WiFi>Choose a network

Similar Messages

Paths will not join with join tool

I'm trying to use the join tool on a pencil path but the paths will not join. I saw a similar question earlier, but no answer was given as it was user error. I'm new to Illustrator, and I don't quite get what he/she figured out he/she was doing. One answer was that the open path should not be more than 1 inch apart, and it's not (0.2). I "scrub" with the join tool, get the blue line, but when I release, the line disappears and nothing happens? At this point I can't even figure out what's going wrong so I can backtrack. Ideas anyone?

Please show a screenshot of the two lines.

Computer will not communicate with router when i try to install upgrade software

I downloaded the upgrade software for a firmwire upgrade and when I type in the 192.168.1.1 address in my internet browser address bar, I do not get connected with the router so I can do the upgrade. I pushed the reset button on the router after I downloaded the software like the manual instructs. The connection keeps getting interrupted for some reason.

What is the Model no of the router...?
Unplug the modem from the router..Only connect the computer to the router on ethernet port1..Hard-reset the router for 45 seconds,power cycle the router and check the ip address you are getting on the computer.
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1...If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter..If you get 4 replies then,Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
Use Internet Explorer to upgrade the firmware.

TS1398 I have just purchased an iPad mini and it will not join my wifi. It detects my wifi network but will not join. I have a Mac, 2 iPhones and an iPad 4 and all work perfectly. The new iPad mini just won't behave. Any ideas?

I have purchased an iPad mini and it will not join my wifi network. Any ideas?

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Since upgrading, both our wireless printers are still visible, but OSX will not connect with them. Both work via connecting from other sources via the same wireless router (airport). What do I need to do to get my printing/scanning working again?

Since upgrading, both our wireless printers are still visible, but OSX will not connect with them. Both work via connecting from other sources via the same wireless router (airport). What do I need to do to get my printing/scanning working again?

First thing to try is reset Printing System:
OS X Mavericks: Reset the printing system
Next would be reset the router (power off 15 secs then back on). And, 2 minutes later, reset the printers 1 by 1.

Computer will not join wifi network. Please hep

I've used it at my home, in the airport, and cafes, and it worked flawlessly, but now in my girlfriend's house I cannot join their network. I even installed a brand new Linksys router today and it still will not join. It finds the network SSID but refuses to join it. All other computers in the house have no problems.
Please help.
Thank you.

Hi Jason,
Yes, other Macs, a MacBook Pro & Black MacBook, are connected to the network. The original router had WEP security and this router has WPA2 Personal security.
I just realized my iPhone won't connect to it either. I'll try resetting it with no encryption.
How do I make a new network location?
Thank you!
Message was edited by: .jacob

Will not join wifi

My iPhone will not join WiFi network... My iPad is on, my Mac is on, but the phone will not join.

Hi Jason,
Yes, other Macs, a MacBook Pro & Black MacBook, are connected to the network. The original router had WEP security and this router has WPA2 Personal security.
I just realized my iPhone won't connect to it either. I'll try resetting it with no encryption.
How do I make a new network location?
Thank you!
Message was edited by: .jacob

2702-UX-K9 Access Point will not associate with controller.

Hi,
I recently purchased nine new 2702 APs. Two of them will not associate with the controller. I realized they they had a different part number. They ended with UX-K9 instead of -K9 like the others. It turns out that these are new AP that are universal for any country. They APs find the controller but need some sort of password to pull the config down. I"m not sure what this could be?
From console of AP @ boot....
examining image...
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
%Error opening capwap:/ap3g2 (Incorrect Login/Password)
Download image failed, notify controller!!! From:8.0.110.0 to 0.0.0.0, FailureCode:4
archive download: takes 0 seconds
*Mar 18 20:16:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.12.10 peer_port: 5246
*Mar 18 20:16:49.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.12.10 peer_port: 5246
*Mar 18 20:16:49.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.12.10perform archive download capwap:/ap3g2 tar file
*Mar 18 20:16:49.439: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
*Mar 18 20:16:49.439: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.12.10:5246
*Mar 18 20:16:49.443: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 18 20:16:49.451: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 18 20:16:49.455: capwap_image_proc: unable to open tar file
*Mar 18 20:16:49.715: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
.... Check out the attached log file for more details.
Thanks in advance for the replies!

Rasika,
I have the same issue on my home 2504 with these 2700 UX, I have tried code 8.0.100.0, 8.0.110.0 (Docs say this is the min version supported), and even 8.0.115.0 (latest available) still no dice. The AP won't register, and gives the error stated above. I am seeing 2 images available for the AP, the AP shipped with the later image but I AP recovery isn't working because it say's unable to find image with XX in the name? I see the TFTP logs, and name the file accordingly no dice, then the unable to find file name -XX pops up too. As you know I am busy during the day this week, but let's jump on a skype and take a look later maybe you have seen something I haven't?
For good measure, also attempted to join a 3650 here at the house IOS-XE 3.6 no dice, going to try 3.7 too tomorrow, It worked for the 3700 UX AP's we had??

MacBook Pro will not dectect Linksys Router

I have recently aqquired a MacBook Pro and i'm at a loss as to why airport will not dectect my Linksys WRV54G wireless router, yet it will detect other secure and non-secure routers in my neighborhood. The MacBook will connect fine to the router via an eithenet cable and work correctly. I have an HP mobile workstation which works fine with the router wirelessly.
To date I have:
rebooted the router several times.
removed the WEP security from the router.
assigned the MacBooks mac address to the router allowing it permission.
I am at a loss as to why it will not dectect the router. I know airport is working fine and so is the router. Any help or suggestions would be greatly appreciated.

Have you tried a different channel?

MacBook will not join Airport network

I am flummoxed. My MacBook will not join my Airport Extreme network. It was fine this morning. I have restarted the MacBook. I have restarted the Airport base station. My iPhone is connecting to the network fine. My TV is connecting to the network fine. My G4 is connecting to the network fine. So, it appears there is some issue with the MacBook itself. Any ideas what could be the issue?

Dr. Kellie wrote:
I am flummoxed.
Are you a Nero Wolfe fan?
My MacBook will not join my Airport Extreme network. It was fine this morning. I have restarted the MacBook. I have restarted the Airport base station. My iPhone is connecting to the network fine. My TV is connecting to the network fine. My G4 is connecting to the network fine. So, it appears there is some issue with the MacBook itself. Any ideas what could be the issue?
First, either update your profile or your OS to 10.5.6. There have been many bug fixes since 10.5.2 and some WiFi updates require the latest Leopard version.
That being said, check your network preferences.
Do you have a rational IP Address?
If you are using an encrypted WiFi, you can temporarily turn off the encryption and see if the MB can join the network. If so, it's an encryption issue. If not, turn the encryption back on and we will have to look elsewhere.
BTW, you should be using WPA since WEP has long ago been compromised and is useless, but thats a side thing right now.
On the MB, I would run disk utility and repair permissions for starters.

Macbook pro will not pair with Vizio sound bar.

Macbook will not pair with Vizio sound bar. It has paired and worked fine in the past. in the menu bar at the top of the screen it says it is connected but it is not. when I open the bluetooth preferences and try to pair it says pairing failed. any help would be great. thanks.

Me too. sigh
All was well until this afternoon, when I swapped out the batteries on my trusty old Microsoft IntelliMouse Explorer for Bluetooth, which has worked flawlessly for me for a few years now. After I put new batteries in, my MBP wouldn't recognize it. I went through the Bluetooth Setup Assistant, and it "saw" the mouse and properly listed it as "Microsoft Mouse". I hit "continue", of course, and the Assistant said "Pairing with your Bluetooth mouse". It got as far as "Connection established" (and I saw the mouse appear in the Bluetooth preference pane", but then I got the dreaded red words: "The pairing attempt was unsuccessful. Make sure your mouse is in range of this computer, turned on and "discoverable." Etc., etc. I made sure of all of those things and tried again, many times, with the same failure every time. I tried different batteries, rebooted the Mac, and so on. No luck.
Figuring my mouse was dead, I went out and bought a Kensington Slimblade Bluetooth Presenter Mouse, brand new, never been paired with anything. Same problem!
Also, I can no longer get my Palm Treo 650 to sync via Bluetooth. It used to be a little flaky (often complained that the port was in use by another application), but rebooting the Treo always solved that. Now, it doesn't.
One trusty old mouse suddenly stops pairing, one brand-new one refuses to pair, smartphone won't sync any more. I haven't installed any system updates or anything else since the Microsoft mouse worked. The only weird thing going on is that I'm having massive network connectivity issues with my broadband connection (probably a flaky cable modem), and a couple of days ago I bought a new Airport Extreme a/b/g/n wireless router, which is at the other end of the house from my computer and now-defunct mice.
Very bizarre. Can the Bluetooth chip or antenna in a MacBook Pro burn out or otherwise fail?
Puzzled and frustrated,
:ian

IPAD WILL NOT JOIN PASSWORD GUARDED WIRELESS NETWORK

My ipad 2 will not join a password guarded Time Warner Cable home wireless network. The network is properly discovered yet I cannot get a password access box to appear. Suggestions please

What encryption is the router using?
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points

My new iphone 5 will not connect with the idrive on my new BMW F30 3 Series - any ideas?

My new iphone 5 will not connect with the idrive on my new BMW 3 Series (F30) via the lightening USB - does anyone have any ideas?

What have you done thus far to troubleshoot your issue? Have you powered down and rebooted your router yet?

Airport time capsule will not communicate with apple tv

I have just purchased the new AIRPORT TIME CAPSULE...it will not communicate with my APPLE TV..

Is the Time Capsule the only wireless router in your current network configuration? That is, is it connected directly to an Internet modem (and not another router) via Ethernet? Is the Apple TV in the same room, different room, or different floor from the Time Capsule?

I have 2 iPads both the sane except for case color. One connects to my home wifi fine, the other will not "join". It finds the wifi name and the little circle turning wheel just spins.

I have 2 iPads both the sane except for case color. One connects to my home wifi fine, the other will not "join". It finds the wifi name and the little circle turning wheel just spins. I have tried about ten different "fixes" none work.. Reboot, forget wifi, etc.
Unplugged wifi on and on for about an hour.
I have compared settings between the two and cannot see any difference.
Both iPads worked fine last week. One made a trip to MI and used cellular access just fine. Now that one still uses cellular OK, but refuses to "join" the wifi.
Too bad I can't attach a picture.
Anyone care to offer a unique workable solution I have not tried?
Thanks
WD9HIK

Have you tried renewing the lease in the WiFi settings? Settings>WiFi>Your network name>Tap the blue arrow>Renew Lease. If you haven't tried that - try it first before reading the information about restoring the iOS software.
Follow the instructions in here. If you are unsure about anything - do not proceed. Post back with questions first.
iTunes: Restoring iOS software - Apple - Support
Make sure that you transfer all purchases, backup the iPad and sync with iTunes first. When you restore to factory settings, iTunes should ask if you want to backup first, but it will not hurt to initiate a backup on your won before you even start the restore process.
How to transfer purchases into your iTunes library
http://support.apple.com/kb/HT1848
How to backup and restore from a backup
http://support.apple.com/kb/HT1766

TS1398 will not join with router

Similar Messages

Maybe you are looking for