TS140 LSI 9300-4i4e not seen in PCIe x16 (slot #1) however works in x4 (slot #3)

I have some TS140s (70A4001LUX 5U with i3-1225 v3 processor) that have tried installing a couple of different LSI 9300-4i43 12Gbps adapters that are not recognized when inserted into the PCIe x16 (e.g. slot #1).
However those cards are recognoized when inserted into the x4 slow (e.g. slot #3). Have tried various LSI 9300-4i4e (cards have most recent fw and bios) in a couple of different TS140s and see the same results. Have verified other cards working ok in the x16 slot.
In the process of updating TS140 BIOS to most recent late fall 2014 version to see if that magicly clears things up.
Has anybody else seen this and know of a resolution other than dont use the LSI 9300 in slot #1?

@I_am_Nivek thks for the info and ideas, I should have mentioned that the onboard RAID on the TS140 was not being used, in the BIOS/Setup, the ATA mode is set to AHCI (other options are IDE or RAID). Also as an FYI/FWIW, on the TS140 or at least the version that I have, the RAID/IDE/ATA is accessed via the "Devices" tab and then under the ATA section. I do recall seeing the "SCU" mode on a different Lenovo system that I have used, might have been a TD340 iirc.
However with the RAID disabled (as it had been), the adapter card still does not appear.
Regarding the boot mode, good idea, I had the TS140 in CSM which enabled both UEFI and BIOS, tried changing it to disable CSM which only allows UEFI mode. However that did not work either.
Is there a different BIOS as well as different motherboard firmware version available vs. what I am using (see above)?

Similar Messages

  • Since I broght Ps6 for Mac, Bridge does not open and crashes. Mini Bridge, however works fine. What should I do?

    Since I broght (in Adobe Store) Ps6 for Mac, Bridge does not open and crashes. Mini Bridge, however works fine. What should I do?

    When I click gelsonhelmoldmacieira1 (me) in the Finder, I do not see the Library:
    The Library (Biblioteca) only appears when I click Macintosh HD:
    Following this path, I add gelsonhelmoldmacieira1 to the others in Photoshop, Bridge and Adobe:
    It seems that something is still wrong. The error message appears again.

  • Non Graphic card in 760GM-E51 PCIe x16 Slot

    Why can't I use the on board graphics and attach a PCIe x2 or x4 SATA controller in the PCIe x16 slot?  Any non graphic board is simply ignored.

    Quote from: Bollwerk on 24-December-10, 03:39:17
    That did it! Apparently, the bridge chip changes it between x16/x1 and x8/x8. Once I switched it to x8/x8 (SLI mode), the Asus card was recognized.
    Thanks!
    Almost, it changes the slots from x16/x0 to x8/x8 
    Nice to hear you got it sorted out 
    Merry Christmas and best wishes

  • Z97 gaming 5 motherboard-2nd PCI x16 slot wired at x8?

    Hi,
    I connected my gtx980 on my 2nd PCI x16 slot and GPU-Z reads as x8.However,when I connected it back to the 1st slot,it reads as x16.Would like to confirm if that's the supposed outcome or is there any BIOS configuration that I can change?
    Thanks

    Yes the second x16 sized slot is only wired for x8 operation. the only way a board like that could have 2 full x16 slots is if it has PLX chips but they are very costly and only get used on stuff like a X-Power model board!
    so its behaving normally on yours as that is how its setup!

  • P35 PCIe X16 slot

    I read that the 2 PCI e video slots will sense which one has a card, and set that one to X16. Is this the case? The reason I ask is my GeForce 9600 (only 1 slot wide) will not seat in the white slot due to interference from the Southbrdge pipe. I had to move it to the yellow slot.
    Thanks,
    Dave

    Thanks...removing the cover gave me just enough space to get the card working although I doubt it's seated all the way. I may have to bend back a few of the cooler fins to make a proper fit.
    Thanks again,
    Dave

  • Hp p400 pci-x8 running in pci-x16 slot

    My thanks in advance for any help I may receive.
    I am currently experiencing a "device not found error"  whilst trying to use an HP p400 array sas pci-x8 adapter in a pci-16 slot. 
    The motherboard is a Gigabyte H81M-S2PV,
    8 gigabytes of RAM,
    650 Watt power supply and
    award modular bios 6.00g and
    intel i3 chip
    HP P400 with 512 cache and battery
    I only have access to the slots mentioned.  I have tested the adapter in three other machines which have the same exapnsion slot arrangements.
    Please clarify if the pci-x8 card should function in the pc-x16 slot? I am trying to assertain if my adapter is faulty.
    Many thanks
    Mutasim
    This question was solved.
    View Solution.

    Thanks for your input PlumCrumble. 
    I was silently sure the card should work but felt it would not hurt to get another opinion.  This reply is accepted as a solution for the first question.
    If I may be bold can I ask if you have any suggestions on my current scenario: When starting the PC,  the screen is black for almost six minutes no messages or indications as to what is happening - then after the period of six minutes or more the PC continues to the normal boot functions; post, loads Windows etc.  The HP ORCA and other utilities reports device not present. However the Widnows device manager indicates a device with driver error.
    In my humble thinking I believe a device is detected but the firmware or required software is missing,  After trying the Proliant repair and installation boot disk, I am little lost as to what software is required to intialise the the device and set the correct IRQ at the BIOS level of the process.
    Is there software and firmware utility available for the HP P400 at the DOS level that I need to be aware of - I am a novice with this particular HP device and any help would be greatly appreciated.  Linux system also reports the same results.

  • H77MA-G43, which pci x16 slot to use?

    i recently bought the h77ma-g43 mainboard which has both the pci x16 v2.0 and 3.0 slots, i was wondering which one to use for my nvidia gtx 580 which is a v2.0 card. please reply soon...thanx

    Normally, it is the PCI-E 16X33 slot closest to the CPU.

  • MSI K9AGM2-FIH: PCIe x1 card in PCIe x16 slot

    Am trying to get a PCIe x1 2-Port Sil3132 SATA Controller to work in a x16 slot
    system boots without any problems, the card is found, and it shows up when booting
    but here is the problem, windows wont boot, when i remove the card from the x16 slot it boots fine 
    windows is run via the onboard sb600
    x1, x4, x8 cards should work in a x16 slot just fine, after with i have heard

    Question, why do you want to use that card?
    Also, it might be possible that drive-letters change in Windows, so it can't boot anymore.
    Try booting with the Windows Boot-cdrom, load the Sil driver and see what letters you get.
    You might need to change the boot.ini

  • HP 3478A DMM not seen with PCI/GPIB 488.2

    Hi All,
    I'm really new at this so watch out...  I have an old 3478A which is compliant with the old HP-IB (GPIB) connector and I'm trying to communicate with it using a PCI/GPIB 488.2 card.  I found some drivers for Labview and that's wonderful but it simply doesn't work.  The automation explorer also doesn't see the device.  What am I doing wrong?  I read somewhere that you have to enable some old drivers but I the message was somewhat unclear now I'm just desperate.  Please help someone.
    OS : win XP
    Labview: 7.1
    thanks

    It is possible the cable is faulty. The cables I am using are National Instruments 763061-02 RevC; Type-X2. These cables work on all of the instruments I am using. Check the configuration of your GPIB Card, I have provided screen captures of my current settings that are working for me.
    1. As before use the Measurement and Automation Explorer to get to the GPIB Bus under devices.
    2.Right click on the GPIB Bus and select properties, you should see the following screen.
    3. Click the Configure and on the next screen click Software>> button to see all of the options.
    Try these settings(I have not made any changes these should be Default).
    Message Edited by AndrewAlford on 11-25-2005 02:23 PM
    Andrew Alford
    Production Test Engineering Technologist
    Sustainable Energy Technologies
    www.sustainableenergy.com
    Attachments:
    ConfigGPIB.JPG ‏39 KB
    GPIBconfig.JPG ‏14 KB

  • HELP!!!!! 915GM Speedster-FA4 PCIe x1 slot not working - SORTED

    Hi, I am at my whit’s end with this motherboard, I cannot get the PCIe x1 slot to work. When I use the PCIe x16 slot it recognises the option card OK but the x1 slot will just not see it.
    I know the network socket 1 needs to active for the PCIe x1 slot to work.
    Any help would be appreciated.
    SORTED - IRQ clash with the onboard boot ROM for Lan socket 2 - NOT DOCUMENTED - MSI PLEASE TAKE NOTE

    Sorry there is no MSI in here....
    It seems that nobody used that config to be able to help.
    And no, I'm not from MSI either

  • IdeaCenter K410 - PCIe x16 question

    In the image w/ my post, I have this question:
    Is this (PCIe x16 slot) a "lever" that opens to insert a video card?  (see image w/ part circled in white)
    I tried to pull it and it doesn't seem to open.  I thought you weren't supposed to insert any "cards" or Memory (RAM) on an angle.  Isn't that so?  It seems that would be the only way to put in the video card that I have for the PCIe x16 slot.
    I know the part of the video card that goes under this area on the PCIe slot but "DOES IT MOVE" to allow installation?
    Thanks for your help.
    Erik
    "This is NOT my motherboard" I'm just using as a reference.  The PCIe x16 slot seems to be exactly the same. 
    Link to picture
    Moderator note; picture(s) totalling >50K converted to link(s) Forum Rules
    Solved!
    Go to Solution.

    Hi Erik,
    Thanks for posting and welcome to the community.
    Base from what you've described and after checking you link, I would suggest you to insert the graphics card in an upwardly position. However when imserting the card tilt the card so that the smaller teeth of the card gets postion first and them firmly placing the rest of the card into potion untill the back bracket (the one circled in your pricture) locks into place. It should fit nicely. If by any chance that the postion is obstructed by the bracket, press down on the bracket so that you can firmly postion the card and locking it into place.
    Hope this helps.
    Do let me know should you require further clarification.
    regards

  • AGP in PCIe x16

    Could I use a agp graphics card in my pcie x16 slot?

    Thank you for the helpful information.

  • Latest FirePro cards not supported in first 16x slot on S20

    I have a few of the new Firepro cards (specifically the W5000 and the W7000) and I am finding that neither of them will work when they are placed in the first 16x slot of my S20. If I place them in the second 16x slot, then it will work. This is not good as I want to run two cards. I currently am running a Geforce GTX 480 in the first slot and it is behaving as expected.
    Is there a specific vbios that is required for this to be recognized in the first slot. 
    Note that the LED light on the back of the card is red and I am getting the video not found post beeps. I am also on the latest system bios.
    Thanks

    Just to be clear, mixing NV and AMD cards is a bad idea.  I think you're trying to get a config working with multiple Firepro cards, but it wasn't totally clear.
    Taking the GeForce card out of the equation, the Firepro cards in question aren't officially supported.  From a power perspective, the W7000 is 150W TDP (or lower) and the W5000 is bus powered.  So dual W7000 shouldn't be an issue there.
    My guess is you're running into BIOS issues, and probably more specifically OPROM issues.  It could be a space problem, so disabling features such as second LAN and PXE boot (if they are not used) is an option.  But given that we've done no official qual work on those cards, it's hard to say what the exact problem is.
    Also note that the first x16 slot on the bus that gets detected by BIOS is the "lower" x16 slot...so your "primary" card should go there.
    I'll finish by my standard canned response of:
    The W5000/W70000 is not officially supported
    NV GeForce cards are not officially supported
    Mixing of the two above cards are definintely not supported

  • Anyone else have an AGP card that\'s seen as PCI in device manag

    Does anyone else have an AGP card that's seen as PCI in device manager > display adapters > general > location PCI bus 1,device 0, function 0
    I'm running Win2k and that's what mine says
    I have my video set to agp in bios :(

    I think that is correct, even though it sounds strange (sometimes USB is seen as COM3). But if you are not sure about the status of the AGP, use a program like WCPUID . Sometimes, under Win98 the AGP is not enabled unless you install first the drivers for the motherboard.

  • Ipod not seen by windows or itunes

    Hello, I'm totally frustrated and have been searching for hours. Please someone help.
    - Nano 8 gb
    - Windows xp
    Neither Windows (my computer) nor Itunes sees my ipod. Ipod is working fine: did the menu/select thing, cable is good.
    When I plug the ipod in the usb port I hear a bleep and I get a message bottom right "new hardware found ipod"and the icon is a usb cable. Ipod is not in My computer window. Ipod is not seen by Itunes
    Tried Device Manager/I see Ipod with a ? Yellow. If i right click on it and do update driver the ms computer management system crashes and sends error report.
    I tried dowloading the USB driver and placing it in the directory, but I got stuck because there is no windows/inf directory. I tried to update the usb driver with the same ms crash.
    I'm completely frustrated, please can someone help me.

    I was having the same problem the other day. I'm not sure what it was but I think it has something to do with the i tunes and i pod 1.2 update.
    What I did was:
    1. Uninstall i tunes
    2. Restart my computer
    3. pluged my ipod in a slow usb line
    4. waited until my pc recognized it in there. It took a little while.
    5. re installed i tunes from apple.com
    6. waited until i tunes recognized my ipod
    7. updated my i pod with my library it took a long time because i was in the slow usb plug.
    8. re plugged my ipod into a 2.0 usb line
    9. i tunes recognized it.
    10. I then updated my ipod to the new 1.2 version
    11. The problem started happening again
    12 I repeated what I did before and now it is working.
    It was very frustrating! I hope it works for you.1

Maybe you are looking for