TS1538 download of restore/recovery stops before completion,saying it is password protected

Forgot password and wanted to do a recovery. I followed the recommended steps but download of restore/recovery stops before completion,saying it is password protected.

Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.

Similar Messages

All most downloaded but stops before complete, with wiindows error 206

all most down loaded, but stops before complete windows error 206

Stewart
This forum is for questions regarding the LabVIEW Datalogging and Supervisory Control Module. You will have more luck posting this question in the general LabVIEW forum.
Good luck

Backup stopped before completing. The process cannot access the file because it is being used by another process

I am working with a client who is attempting to backup to a NAS device
The device is a linksys NSS6000 (Cisco device).
It’s a dual 1Gbit LAN device that supports CIFS / FTP and NFS transfers. It has only 1Gbit lan connected.
The device has 4 * 500 gb sata drives in raid 1 attached.
Cables go from cat 5 to fiber back to cat5. (The NAS is located at a neighboring office) The switches are 1gbit.
Server is a win2k8r1 fully up to date.
When backing up to the NAS device, the following error occurs:
Running backup of volume Local Disk(D:), copied (86%).
Running backup of volume Local Disk(D:), copied (90%).
Running backup of volume Local Disk(D:), copied (94%).
Running backup of volume Local Disk(D:), copied (98%).
Backup of volume Local Disk(D:) completed successfully.
Backup stopped before completing.
Summary of backup:
Backup stopped before completing.
The process cannot access the file because it is being used by another process.
If we redirect the backup to a folder on a 2008 share, the backup completes successfully.
Only when backing up to the linksys NSS6000 does the error occur.
No other backup processes are writing to the NAS device so I can't understand why the process thinks the file is
being used by another process.
One thing we did notice that when the backup to the NAS device occurs, throughput is about 150 mbit average
On the 2008 server shares we successfully backup to, the through put is 500 mbit. Not sure if that is important, but
might be worth mentioning.
The following event log entry was noted at the end of the backup.
The description for Event ID '519' in Source 'Microsoft-Windows-Backup' cannot be found.
The local computer may not have the necessary registry information or message DLL files to display the message,
or you may not have permission to access them. The following information is part of the
event:'2009-05-12T10:13:31.617Z', '', '2147942432', '%%2147942432'
Any ideas?
Thanks..Michael

I am also seeing the same problem backing up nightly to a brand new NAS device (WD My Book Live)
All the error codes are the same as those in this thread.
From Windows Event Viewer:
The backup operation that started at '‎2011‎-‎03‎-‎25T06:00:19.811302700Z' has failed with following error code '2147942432' (The process cannot access the file because it is being used by another process.). Please review the event details
for a solution, and then rerun the backup operation once the issue is resolved.
Fault bucket 659897467, type 5
Event Name: WindowsBackupFailure
Response: Not available
Cab Id: 0
Problem signature:
P1: Backup
P2: 6.1.7600
P3: 0x80070020
P4: 7
P5:
P6:
P7:
P8:
P9:
P10:
Attached files:
C:\Windows\Logs\WindowsBackup\WindowsBackup.1.etl
These files may be available here:
C:\ProgramData\Microsoft\Windows\WER\ReportArchive\NonCritical_Backup_6957d65de91fc4a853ecc7c78914bf7351fff0d1_14578325
Analysis symbol:
Rechecking for solution: 0
Report Id: dd480bf2-56a6-11e0-ae81-00217099bf56
Report Status: 0
From Report.wer in C:\ProgramData\Microsoft\Windows\WER\ReportArchive\NonCritical_Backup_6957d65de91fc4a853ecc7c78914bf7351fff0d1_14578325
Version=1
EventType=WindowsBackupFailure
EventTime=129455071508181139
Consent=1
UploadTime=129455071508201140
ReportIdentifier=dd480bf2-56a6-11e0-ae81-00217099bf56
Response.BucketId=659897467
Response.BucketTable=5
Response.type=4
Sig[0].Name=Operation
Sig[0].Value=Backup
Sig[1].Name=AppVer
Sig[1].Value=6.1.7600
Sig[2].Name=HRESULT
Sig[2].Value=0x80070020
Sig[3].Name=TargetType
Sig[3].Value=7
DynamicSig[1].Name=OS Version
DynamicSig[1].Value=6.1.7600.2.0.0.256.48
DynamicSig[2].Name=Locale ID
DynamicSig[2].Value=1033
State[0].Key=Transport.DoneStage1
State[0].Value=1
State[1].Key=DataRequest
State[1].Value=Bucket=659897467/nBucketTable=5/nResponse=1/n
FriendlyEventName=WindowsBackupFailure
ConsentKey=WindowsBackupFailure
AppName=Windows host process (Rundll32)
AppPath=C:\Windows\System32\rundll32.exe
ReportDescription=Windows Backup failure

When ever i try to download my iPod recovery software, it keeps saying connection timed out. really annoyed and need help to fix it

when ever i try to download my iPod recovery software, it keeps saying connection timed out. really annoyed and need help to fix it

- Next try the manual install method of:
iDevice Troubleshooting 101 :: iPhone, iPad, iPod touch
If the iPod was Disabled, place the iPod in recovery mode after the firmware download is complete and then restore using the instructions in the article. Sometimes recovery mode timeouts and returns to disabled before the firmware download is complete.
- Then try on another computer

Hi I'm try to set up a new Epson printer SX 445 to my router/network but each time I run the set up wizard it fails to complete saying Security Key/Password Check fail. *entered security key/password does not match the one set for for router. I know th

Hi
On my macbook pro
I'm try to set up a new Epson printer SX 445 to my router/network but each time I run the set up wizard it fails to complete saying Security Key/Password Check fail.
*entered security key/password does not match the one set for for router.
I know that the password is correct and have rechecked this by changing it a few times
and I still get the same result.
My network internet service provider is not interested and says to call Epson.
Anybody have any clues how I can resolve this?
Regards

I personally suggest the new Drobo FS. Since it has an iTunes server built in and you can use any size sata hard drive in it it is better and a NAS that has to use the same size drives.

I am downloading new itunes onto iphone 4 and it stopped before completion and now there is a usb and itunes picture on screen and is frozen

any help on getting the frozen screen off?

Hello, Spedellen.
Thank you for visiting Apple Support Communities.
When experiencing issues restoring an iPhone, here are the best articles to go through. If you received a specific error number when restoring, see the section labeled Get more help in the second article below.
If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Resolve iOS update and restore errors in iTunes
http://support.apple.com/kb/ts1275
Cheers,
Jason H.

Download stopped before completion

incomplete download. help.

Incomplete download of what?
If help is desired, provide some details of the issue occurring.

TS1702 I am updating my IPAD to version 5.1 and the update has stopped before completion. What is the procedure. If I stop the update or restart the IPAD will the update be corrupted and also the IPAD operating system.

I am updating a new IPAD to the latest version from ITUNES. The update is not complete and has stopped. What is the procedure to restart? If I close ITUNES i get a message that the IPAD is updating. Will closing the application cause the update to be corrupted and thus the operating system? Will the same occur if I power the IPAD down or disconnect it vis the USB port?
Help!!!

routnom wrote:
AppleWill - when i closed the app and restarted Itunes, I had to go thru a Restore process. The restore goes to certain point and stops. It seems at the same time as the Update stopped. I can Force a stop and reboot the computer and try again. It possible the screensaver interrupted the restore? It doesn't sound right. Any suggestions?
You may also want to go to:
~/Library/iTunes/
This is done by going to the "Go" in the Finder and select Go To Folder. Copy and paste:
~/Library/iTunes/
In to Go To Folder selection. Look for a folder called iPad Software Updates. Delete anything in that folder and re download the upadate.

DVD Playback stops before completion of slidshow

Please help -- for some reason -- the playback of my slideshow (about 20 min) stops about half way thru the playback. I've had this happen before and have no idea.
Anyone have the answer?
Thanks

If you created your slideshow in iDVD, you are limited to 99 slides. Your slideshow is probably stopping on the 99th slide. If that is the case, you need either to do your slide show in iPhoto or in iMovie, where there is no limitation on the number of slides, and then export them into iDVD.

Importing stops before complete

I'm new to iTunes and have been trying to import tracks from a CD that is made up of individual tracks downloaded from the internet some time ago. The CD has 18 tracks and only the first 10 will import. On the 11th, I can hear the CD player "surging" and the track shows that it is partly imported but will not complete.
Tried skipping the 11th track but same thing happens to 12th, 13th etc.
What's happening??
P.S. I have had no trouble importing all tracks on any any purchased CD.

Home burnt CDs, especially ones made "some time ago," are more prone to problems than commercial CDs.
If you still have the original tracks in MP3 format, copy them to the new computer (using a USB flash drive or other medium) and add them to the iTunes library directly.
If the only source you have is the audio CD, try ripping again in iTunes with the "error correction" preference turned on, and if that doesn't work, try ripping in another program, such as Windows Media Player or Exact Audio Copy, and adding the resulting MP3s to the iTunes library.

Hi, i was downloading movies and it stopped it and says error -50

it stoped my download and says error -50

Hello lorencook84,
Thank you for using Apple Support Communities.
For more information, take a look at:
iTunes Store: "Error (-50)" when downloading purchased content
http://support.apple.com/kb/ts1583
Have a nice day,
Mario

How do I download flashplayer when message just before finish, says newer version already downloaded, which isn't true?

I am using Windows 7, Internet Explorer 11,on a Compaq CQ5210F PC. I am trying to download Adobe Flashplayer. When the download process gets to the point where you are supposed to click the Finish button, a message appears underneath the download progress bar, that says, "Newer version already downloaded", which is false. I hit Finish button anyway, and I am shunted to another screen for problem solving, which does not work. Any ideas, suggestions, help from anyone?

Hello Dale,
Please do the following:
Download the uninstaller from this page, Uninstall Flash Player | Windows.
Download the installer(s) corresponding to the browser(s) you use from this page, Installation problems | Flash Player | Windows. They are posted at the bottom of the page in the 'Still having problems section'.
Delete any installers you have previously downloaded.
Run the uninstaller. After running the installer launch Windows Explorer and navigate to \Windows\System32\Macromed\Flash. Ensure the directory only contains the FlashInstall.log file. If you have a 64-bit OS, please also check \Windows\SysWOW64\Macromed\Flash directory for the same.
If other files exist (e.g FlashUtil..., NPSWF..., Flash...ocx, etc), reboot your machine to remove these files.
Run the installer(s) downloaded from step 2.
If you are still encountering issues after executing these steps, please post a screenshot of the \Windows\System32\Macromed\Flash (and \Windows\SysWOW64\Macromed\Flash if 64-bit OS) as well as the contents of the FlashInstall.log file (from both directories if applicable).
Thank you.
Maria

How can i restore my ipod touch to factory settings when password protected

my son got a hold of my ipod touch and changed the password now he cant remember it and no one can get into it or get it to reset or restore i have tried holding the on/off button and home button for 10 secs but it keeps telling me it is disabled on my ipod screen ? plz help me fix this problem

Place the iPod in Recovery mode and then connect the iPod to your computer and restore via iTunes.
iOS: Wrong passcode results in red disabled screen

Can a document author password protect something after its already downloaded?

If I download a document from a website and am not required to enter a password to open it after I’ve downloaded it, is it possible for the author to add password protection to the downloaded document later? For example, let’s say I am a member of a paid website that allows its members to download documents. Let’s say I’ve downloaded some stuff and was not required to enter a password at the time. If I cancel my membership can they somehow change my downloaded copy in my computer and add password protection? Meaning if I cancel my membership I could possibly lose access to the stuff I’ve already downloaded?

Awesome. I looked up online how to check to see if they used DRM and they don't for any of their documents. Thank you so much!

Downloaded the latest software ios6 on my ipod. when i plug it into my computer itunes tells me ipod is in recovery mode you must restore this ipod before it can be used with itunes, how do i fix this?

ok, so i finally found my ipod. I pick it up and it asks me if i would like to download the latest ios6 software so i did. Then moments later it died, ran out of battery. So i pluged it into my computer via apple usb cord. Then this is what itunes says "iTunes has detected an iPod in recovery mode.You must restore this iPod before it can be used with iTunes". All i want is to get my notes from the utilites section there so important to
If i restore it will my notes still be there, i dont want to restore original settings or something like that .
please help me what do i do?

You have to restore the iPod, no ifs, ands, or buts...
After iOS is installed you will be asked if you what to set it up as a new iPod or if you want to restore from a backup.
If you have a good backup you can restore that and you're good to go.
If you don't have a good backup, then you end up with a "clean" iPod....

TS1538 download of restore/recovery stops before completion,saying it is password protected

Similar Messages

Maybe you are looking for