TS1559 I cant get past the choose network screen

I cannot get past the choose a network screen

Hello DionSimmons,
The following article provides information and troubleshooting steps that can help get your iPhone activated.
iPhone: Troubleshooting activation issues
http://support.apple.com/kb/TS3424
Cheers,
Allen

Similar Messages

HT4623 i cant get past the resuce email screen during the upgrade

i cant get past the resuce email screen during the upgrade

Hello DionSimmons,
The following article provides information and troubleshooting steps that can help get your iPhone activated.
iPhone: Troubleshooting activation issues
http://support.apple.com/kb/TS3424
Cheers,
Allen

HELP cant get past the start up screen

Hi all!
Today my computer was running super slow so I was forced to restart it by holding down the power button, however, when it began to start back up it never made it past the start up screen. Ive tried multiple things to try and get it to start up again, resetting it, keeping it plugged in in case maybe the battery was dead, and it wont even let me start it in safe mode. The light on the bottom right corner that I think normally lights up isn't lighting up now either, I dont know if I need a new battery or if the computer needs to be sent in to be repaired, or whats going on. Does any one have any suggestion about what I should do?? I'm sure there are multiple things im not trying because I'm unaware of them, so if any one has ANY suggestions that would help! thanks!

If it is not seeing the WiFi network and will not connect you can try restarting that one iPad and then try again. If it still will not cooperate, activate it using iTunes on a computer and then troubleshoot the network connection after the device is up and running.

My serial number is not recognized and I cant get past the first setup screen. What do I do?

I cant get the installer to recoognize my serial no. What do I do

As well as the new download you will need the new serial number. You cannot use your original serial number.
(Don't expect it to work on modern versions of Windows or Mac OS though!)

HT204266 I cant get past the security questionsand I dont in order to change my questions

I cant get past the security questions and I dont know the ole answers in order to change my questions

See this previous discussion:
HT1491 How do i get the security...: Apple Support Communities

I am unable to get past the apple login screens on my iPad to access my settings menu for a new home network. My password is not recognized so I cannot even get into the settings mode to make a chance. How can I get past the Apple logins?

I am unable to get past the apple login screens on my iPad to access my settings menu for a new home network. My Apple password is not recognized so I cannot even get into the settings mode to make a chance. How can I get past the Apple logins?

Hey Dpcupcake,
If you can not get past the sign in screen on your iPad, you will need to use the steps in this article to recover use of your iPad -
Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support
Thanks for using Apple Support Communities.
Happy computing,
Brett L

Imac frozen at blue screen after i went into disk utilities and cleaned my free space. I tried holding down T key as it reboots and i get a message. Start up disk full empty it how can one emptie it if you cant get past the blue screen

Imac frozen at blue screen after i went into disk utilities and cleaned free space.
I tried holding down T key as it reboots
and i get a message. Start up disk full empty it how can one emptie it if you cant get past the blue screen?
to make matters worse we bought the IMAC of amazon uk on the 4/07/011 so what can we do?
please remember how frustrating it is when asking for help when the helper telling you to type something on the screen when its frozen
Tell us when you can type some instuctions to the software how do you get to the doss prompt so to speak to do this
Thanks

i tried all this thanks
i can not get past blue screen and message Your disk is full it needs to be emptied Please not I cant proceed past this message.
no matter what you tell me
Am i right ok in thinking that
when i went into disk utilities and chose to clean my free space i left it over one hour to do its stuff
i came back and there was no progress bar just the box so i quit the program and when i opened mac mail the system just froze i forced quit mail rebooted and blue screen death
Now when free space is being cleaned is it the same as windows dose the utility write lots of 0 on the hard drive then rebbot its self to free the space
basicly is my hard drive full of 00000 is this why im getting this message because the process was interupted
I need to know if i need outside help i bought the computer on line on amazon uk what dose one do next

Cant get past the starting mac os x screen

hey im posting for my brother.. he has a macbook and now when he turns it on he cant get past the blue "starting the mac os x" screen its just stuck there.. HELP ?!?

Start up from the disk that came with the computer (or an upgrade disk). (Insert the disk, hold down the “C” key-it takes awhile so be patient. If it starts up to the install screen, click continue in the window that first appears. Then select “utilities” in the finder menu and select "disk utility”. Your HD should show up in the sidebar window. Highlight it and click the "repair disk” button. Come back with your results.

Cant get past the cancel or save menu in setup

Im trying to setup my iPod Touch so I can use it, but I Cant get past the cancel or save menu in setup. I chec the user agreements everytime and I have also tried to save.
I think the problem is I am using a 15 inch normal moniter and there might be another button to push that I can not get to. I have tried minimzing the left panel side but it only goes so far.
Can Somone help me?

Or use the arrow keys on the keyboard to scroll down to the bottom of the page.

HT1349 I cant get past the wire less hook up

we just got an ipod touch and we are trying to get it set up without the wi-fi. but cant get past the wi fi set up

Check out this link https://discussions.apple.com/message/12835691#12835691

I cant get past the log in page

I download the Acobat XI pro. I cant get past the log in page. The response is "connect to the internet and try again". I am connected.

hello any one help me please tell me about flash player. http://www.shechoice.co.uk/ how can i instal flash player in window 8.

Help ! i have done an IOS 5 udate and cant get past the track my iphone set up screen. i have done restored 3 times. going crazy

Udated to ios 5 and cant get past the find my iphone screen.

Try deleting an other icloud backup and see if it will automatically backup.

My macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help

my macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Apple ID. My newly updated iPad 2 wants an email for the apple ID. My apple ID is not an email address. How can I get past the set-up screen?

My newly updated iPad 2 wants an email for the apple ID. My apple ID is not an email address. How can I get past the set-up screen?
I can't change my Apple ID. It would mess all my stuff up.

To change the iCloud ID you have to go to Settings>iCloud, tap Delete Account, provide the password for the old ID when prompted to turn off Find My iPhone (if you're using iOS 7), then sign back in with the ID you wish to use. If you don't know the password for your old ID, or if it isn't accepted, go to https//appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID. Tap edit next to the primary email account, tap Edit, change it back to your old email address and save the change. Then edit the name of the account to change it back to your old email address. You can now use your current password to turn off Find My iPhone on your device, even though it prompts you for the password for your old account ID. Then go to Settings>iCloud, tap Delete Account and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud). Next, go back to https//appleid.apple.com and change your primary email address and iCloud ID name back to the way it was. Now you can go to Settings>iCloud and sign in with your current iCloud ID and password.

I can't get past the grey apple screen using mavericks

I can't get past the grey apple screen trying to boot up with Mavericks. I had been using Mavericks for about a month (only had issues of freezing occasionally). I read in one of the posts here that I should try holding command R down when booting. I did now I just get a grey screen without the apple. Any advise?
I have a Mac Mini

Hello ther cnickers,
It sounds like the initial install of Mavericks went ok, and you have been using it for a while, but now cannot boot to your desktop and are stuck at a gray screen with an Apple logo. I would recommend a couple of things here:
First, try performing a Safe Boot to see if that will load up for you. If so then leave Safe Boot and restart from the Apple menu to try and get to your deskop:
To start up into Safe Mode (to Safe Boot), follow these steps.
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key.
The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple logo and the progress indicator (looks like a spinning gear).
After the logo appears, you should see a progress bar during startup. This indicates that your computer is performing a directory check as part of Safe Mode.
To leave Safe Mode, restart your computer without holding any keys during startup.
From: Mac OS X: What is Safe Boot, Safe Mode?
http://support.apple.com/kb/ht1564
If that works fine, I would next also verify and repair your disk if needed.
Disk Utility 12.x: Repair a disk
http://support.apple.com/kb/PH5836
Print this help page so you can refer to it later. (You don’t have access to Disk Utility Help when you restart up your computer in the next step.)In the Disk Utility Help window, choose Print from the Action pop-up menu (looks like a gear).
Choose Apple menu > Restart. Hold down the Command (⌘) and R keys as your computer restarts.When you see a white screen with an Apple logo in the middle, you can release the keys.
Click Disk Utility, and then click Continue.
In the list at the left, select the item you want to repair. (Be sure to select an item that’s indented to the right in the list, not an item at the far left.)
Click First Aid.
If Disk Utility tells you the disk is about to fail, back it up and replace it. You can’t repair it.
Click Repair Disk.If Disk Utility reports that the disk appears to be OK or has been repaired, you’re done. Otherwise, you may need to do one of the following steps.
If Disk Utility reports “overlapped extent allocation” errors, two or more files occupy the same space on your disk, and at least one of them is likely to be corrupted. Check each file in the list of affected files. If you can replace a file or recreate it, delete it. If it contains information you need, open it and examine its data to make sure it hasn’t been corrupted. (Most of the files in the list have aliases in a DamagedFiles folder at the top level of your disk.)
If Disk Utility can’t repair your disk or it reports “The underlying task reported failure,” try to repair the disk or partition again. If that doesn’t work, back up as much of your data as possible, reformat the disk, reinstall Mac OS X, and then restore your backed-up data.If you continue to have problems with your disk, it may be physically damaged and need to be replaced.
Thank you for using Apple Support Communities.
Cheers,
Sterling

TS1559 I cant get past the choose network screen

Similar Messages

Maybe you are looking for