TS1702 On resetting, apple logo appears and stays on ipad3
An ignorant technician whom I went for the sim, after inserting the sim just did the resetting. An apple logo appeared and never went away untill the whole battery just drained away. As I put the iPad on charging, it came back to life but mail and safari not working. When I tried to reset, again apple logo appeared and stayed till the battery drained. Again charged it and it came to life, then tried to reset to factory settings by erasing all contents, that too didn't work. A revolving circle appeared and stayed till the battery drained. My last try was, connected it with iTunes to reset it, but it says that latest iOS version will be installed, that I don't want, so didn't proceed further. Now I am stuck with my mail and safari not working. Please help as to how can I get the mail and safari working aging. Thanks
Try and force iPad into Recovery Mode (data will be lost)
1. Turn off iPad
2. Connect USB cable to computer; leave the other end alone
3. Press and hold the Home button down and connect the docking end of cable to iPad
4. Continue holding the Home button until you see the "Connect To iTune" screen
5. Release the Home button
6. Open iTune
7. You should see "iTunes has detected an iPad in recovery mode"
8. Use iTune to restore iPad
Note: You need to be patient and repeat the above many times to recover your iPad
Similar Messages
-
My mini ipod appears off and not respond to any commands when pressed the buttons to reset, apple logo appeared and then the apple support site and it shuts down. already tried all the steps, but none worked, and when I plug it into my computer it does not appear in the iTunes bar. what do I do?
If MacKeeper corrupted the Recovery partition then even I underestimated its potential for damage. Garbage "cleaning" apps will cause misery but I have not found that the Recovery partition to have been affected by using MacKeeper or anything like it. I doubt that it did so, but I have learned not to underestimate the potential for such things to result in system corruption.
Before concluding your Mac has a hardware failure, try booting OS X Internet Recovery by holding command option r on startup (three fingers). That will force your iMac to bypass the Recovery partition altogether, and convey the ability to create a new one.
An Internet connection will be required (wired or wireless).
At the Mac OS X Utilities screen, select Disk Utility. Select your startup volume (usually named "Macintosh HD") and click the Repair Disk button. Describe any errors it reports in red. If Disk Utility reports "The volume Macintosh HD appears to be OK" in green then you can be reasonably (though not completely) assured your hard disk is in good working order.
Assuming the HD remains usable you can then use Disk Utility to erase it. Reinstall OS X, restore your essential software and other files, and don't reinstall the junk. -
I resets my iphone without disabling touch ID lock, it restarts, apple logo appears, and it stays like that, it never starts till now, just the apple logo and stays that way, please give a solution???
Hi ahmedsgh,
I'm sorry to hear you are having issues with your iPhone. If it isn't responding or starting up past the Apple logo screen, you may find the troubleshooting steps outlined in the following article helpful, in particular this portion:
If your device gets stuck during startup
When starting up, you might see the Apple logo or a red or blue screen for a long time, or your device might restart again. Try these steps:
Make sure that you have iTunes 12 or later on your computer.
Put your device in recovery mode.
When you get the option to restore or update, select Update. This will reinstall iOS without erasing your data.
If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support
Regards,
- Brenden -
Nano won't reset, Apple logo appears and disappears, Nano won't mount!
My battery died on my 1G Nano sometime last night or the night before. I went to try to wake it up today, and nothing happened ... would not wake up.
I connected the Nano to the Dock connector which was directly connected to my 24" iMac. The Nano tried to restart, but would not re-start completely, most likely because the battery was completely dead.
I tried re-setting by toggling on and off the Hold switch and then pressing the Menu and Select buttons, but that did not work. I also tried plugging the Nano into an external USB charger (for regular iPod) and resetting. I still can not get it to reset.
The Apple logo appears on the screen for a second, the screen lights up for a second, then the screen goes dark again and the Apple logo re-appears and the process starts all over again.
This has been going on for over 20 minutes. Apple logo will appear, screen lights up, screen goes dark, Apple logo re-appears, etc, etc, etc, etc. Do you see a pattern emerging here?
Please help!
ThanksWhen my iphone cracked out, I plugged it in. If it is still discovered in itunes, on the left side bar you should see you device's name. If you click it, near the top it will show your device and have options for backup or just plain restore (which I might recommend here). And if this works awesome! If not, RIP iPhone
-
My Ipad won't start up. The apple logo appears and just stays on the screen. after a while it starts blinking every minute
Try recovery mode as described here.
Note you may have to try to enter recovery mode more than one time to succeed.
HT1808 -
my ipad does not start or reset even. when i hold both buttons only apple logo appears and ipad wont start. plz help somebody
try restoring see guide
http://www.ipadforums.net/ipad-help/2987-how-put-your-ipad-into-recovery-mode.ht ml -
When I use Siri, my screen goes blank and the apple logo appears and disappears. I've reset it, but problem still occurs. How can I fix this?
Did you reset your iPad like this: Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart.
-
I have an older iPod that no longer shows up in iTunes or appears to be charging. When I press the Menu and Select buttons, the Apple logo appears and then an icon of a battery with an exclamation point. Is it dead for good?
If it is otherwise working, you can change the battery. If you want to do it yourself, you can buy the part on eBay and other online sources. Just make sure you know the type of iPod you have so that you get the right part.
http://support.apple.com/kb/HT1353
There are online guides, including the ones on this web site
http://www.ifixit.com/Device/iPod
(Note: Most replacement batteries come with plastic/nylon tools seen in the guides.)
You can also have a repair business do the work.
If it is just the battery, if you do a Reset (using the Menu and Select buttons) while it is connect to your computer, I think it should still be recognized by iTunes. -
i didn't close my mac air down properly and when i tried to use it, the screen was frozen. I turned it off and restarted it, and the grey screen with the apple logo appear and the circle just keeps spinning. Can you advise?
Try resetting the SMC
Intel-based Macs: Resetting the System Management Controller (SMC) -
After a phone reset,apple logo appears but phone wont start
After a phone reset,Apple logo appears on screen,but phone wont start!!
That hapened to me and this fixed it. I dont know what it does or how it works so dont hold me accountable but it worked for me
Entering DFU Mode (Official Instructions)
Plug your device into your computer.
Turn off the device.
Hold the Power button for 3 seconds
Hold the Home button without releasing the Power button for 10 seconds
Release the Power Button but keep holding the Home button
Keep holding the Home button until you are alerted by iTunes saying that it has detected a device in Recovery Mode
Make sure the device screen is blank and no logos are present
Exiting DFU Mode
Hold Home and Power Button till the Apple Logo appears
~Jordan -
Macbook Pro BIOS requires at least 1 minute before the Apple logo appears and Chime sounds.
When I cold-boot my MacBook Pro, it takes a least 1 minute before I get the chime and Apple logo.
Some background on the problem:
After purchase I almost immediately installed Windows 7 on BootCamp and had no problems.
Around 8 months ago I bought a SSD drive and CD-bay kit, put the original HD into the CD bay and the SSD in place of the original HD, installed OSX on the SSD and formatted the original OSX partition, this broke the Windows install.
I tried in vain for around 2 months to repair the Windows partition without having to reinstall it to no avail, so I swapped the positions of the drives.
Since then the Windows & OSX partitions work fine, however from a cold boot it takes upwards of 1 minute before the Apple logo appears and Chime sounds, after that it behaves as expected (maybe 20-30 seconds and I'm fully booted).
Performing a soft restart behaves as expected too (Chime/Logo appear almost immediately and boot time is lightening fast!).
When I close the lid, it exhibits a similar problem in that it takes about 1 minute before it has gone to sleep and I can't do anything to wake it until that time has past.
It's not the end of the world, but it is slightly annoying, so any help would be greatly appreciated.
My guess is some kind of EFI/BIOS problem, but I can't find any other examples of this problem and have no idea how I might fix.When in OS X go into System Preferences and Select Startup Disk. Then select the OS X entry, even though you are in OS X, and reboot.
Some times the hardware gets confused as to which OS to boot and figuring it out can take some time. Once you select the OS X partition as the OS to boot to it should startup faster.
If not then you have some other problem that I am not familiar with.
You might also want to do a SMC reset, Google for the instructions found on the Apple KB site. -
My IMac is frozen with the screen white ,apple logo appears and a spinning wheel under it. A long empty rectangle empty appears under the wheel and is empty.
Your iMac is trying to go into safe. This usually happens when it has detected an issue with the OS or file system.
Follow the steps outlined in http://support.apple.com/kb/TS2570 -
Why does the Apple logo appears and disappears when I'm the iphone 4?
When I'm using iphone 4 the Apple logo appears and disappears and appears lock screen. What to do? It' s a bug or a hardware problem?
Hi sarasalves,
Welcome to the Support Communities!
If the Apple logo is flashing on your iPhone 4, you may need to put the iPhone in recovery mode so that you can restore it. The article below explains how:
If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
I hope this information helps ....
- Judy -
my iphone 4 regularly gets stuck on the apple logo screen and stays there until it runs out of battery, and even during charging. what can i do? I have restored it, still it gets stuck on apple logo, anyone pls help.
Jai141 wrote:
... and im not sure as i brought the phone of someone else.. i will have to ask them
Good Luck.
Jai141 wrote:
Thanks
You're Welcome. -
when i try to install the mac os x 10.7.3 i start up the computer and apple logo appears and it stucks why? and what should i do?
How are you trying to install Lion 10.7.3? Where did you get that version as the current download version is 10.7.4.
Why are you installing 10.7.3? What OS X version was on the computer before you started this install?
Maybe you are looking for
-
I cant seem to play online movies, it tells me to get media player or adobe flash player
I have a problem when I try to watch movies especially Anime online, it tells me to download adobe flash palyer and when I try to download free apps it tells me to give my credit card details.
-
Converting Canon RAW to PS Raw
Hi Folks, wondering if anybody can help me? I am taking photos with my Canon DSLR in RAW, file extension .CR2. When using Canon's Digital Photo Professional, I am only able to transfer the photo to PS, CS3, in a TIF file. I wish to be able to work i
-
me aparece este mensaje cuando intento guardar los cambios en un archivo o intento guardar el mismo y se cierra el programa. no puedo editar mis archivos, no me deja hacer nada por que se cierra, al intentar modificar cualquier elemento.
-
Hi! I have a PC printer (Canon PRIXMA iP3000) that is connected to the PC via an USB cord. I also got a MacBook Pro that I've connected to the network by a WiFi connection. I have the printer shared in the windows setup and I can, from times to times
-
When I receive picture e-mailed from ms skydrive the first picture comes out full size but the rest are very small. Is there any way to fix. I am using a macbook. mexmex