TS1702 Triple clicking on touch screen. I need to triple click (rather than 1 click) for all functions on the touch screen. I have rebooted and upgraded software. Any help please!?
With the Ipod touch it requires 3 x clicking to the touch screen rather than 1 for all interactions. I have updated software, all apps, rebooted and reset but still doing it. Any suggestions very welcome.
All good - as per "Single click on touch screen doesn't work" problem. The VoiceOver under Settings/general/accessibility was set to "on".
When you turn this off, the ipod resorts to one touch instantly.
Similar Messages
-
When I switch to Front Camera, it just blurs the screen and hangs. Any help?
I had the same problem. After numerous attemps to Restore from Itunes, I decided to use the "Setup as New Ipad" option. It went through a few question on new setups. Afterwards all my apps, data, photo's were still intact. Which shows that the Restore from Itunes worked. There must be a small bug that prevents the Ipad to open after "Restore from Itunes" . Hope it will help you.
-
Gray screen when turning on iBook G4 with tiny file folder in center of screen blinking finder icon and question mark. I cannot figure this out. Tried everything I know. Can someone help please???
Hello,
Ideally you need to boot from the disk as you have no other media advisable. (e.g your hard drive)
Without some form of system disk or restore you wont be able to diagnose the problem with your hard drive.
By using a Mac OS X system disk you can load up the Disk Utilities and repair the hard drive if shown it's available. If it's not available you would need to replace the hard drive and reinstall Mac OS. Without any disk to support you, you are going to struggle.
You can obtain replacement disk, both retail copies or system disk on the Internet.
If you know what version of Mac OS X you had install (I'm guessing that it would have been 10.3, but would recommend 10.4) A retail disk is normally black with a colored 'X' on it, while system disk are always.
Always try and obtain a copy of the system restore disks (Gray) for your iBook
Ebay is another outlet that has genuine system disk for sell, but like any auction site, it's as and when someone is selling them.
The only other thing you could do is take it to a Apple repair agent who could check the hard drive on your behalf. That way you can get confirmation if the problem is the drive or some other fault. They may even help restore the OS for you.
I can't think of anything else to try without some form of disk to help you.
There maybe just one other small thing you could try.
When booting up, firmly rest your palm of your hand on the iBook next to the tracker pad on the left side.
If it works then it's another fault that I'm aware of. -
Help needed in SD VC Assigning Object Dep. for all values at the 1 time
Dear, Gurus
I am successful in achieving pricing in VC the long way example: If Characteristic is Car_Color and values Blue, Red. I assign
$self.Z_CarPrice=u2019Redu2019 and it works. Z_CarPrice is basically the variant condition linkage with tables SDCOM and VKOND.
My question is how can I achieve the above by assigning it to the header so that it automatically enters the code $self into all values without me having to go into it 1 by 1 and assigning the codes? Or what is the best way in achieving the results?
If I have 3 characteristics ex: Car_Model, Car_Color, Car_Size? 100's of values? 4th characteristic is Z_CarPrice inside this I have entered all the Values from the 3 characteristics.
Thanks in AdvanceHi,
Try these steps and hope will definitely resolve your issue
Create one variant table VT_BASE_PRICE with combinations of the char Z_COLOR,Z_MODEL and Z_SIZE as key fields
Table Structure
Z_Color
Z_Model
Z_Size
Z_Car_Price
Table Contents
Z_Color Z_Model Z_Size Z_Car_Price
RED Honda Big BP_RED_HONDA_BIG
RED Honda Small BP_RED_HONDA_SML
Maintain the table values with all possible combinations and for each combination enter a unique key under Z_car_Price column. Remember the variant key length Max is 26 and you can use any unique value which should give a meaning by looking at
Once maintained the table write a dependency
Table VT_BASE_PRICE
(Z_COLOR = Z_COLOR,
Z_MODEL = Z_MODEL,
Z_SIZE = Z_SIZE,
Z_CAR_PRICE = $self.Z_CAR_PRICE)
Thus for each combination no need to write the code to infer the variant key. It will automatically choose from table as per configuration values entered.For each variant key you need to maintain price in condition records for condition type.
Regards,
Brahmaji D -
Hello, is it possible to turn of all functions in the locking screen? even the turn off function (also for security reasons / so that it cant be turned of while using find your iphone?)
Mav-erik wrote:
Yes of course, i know... havn`t lost it but however makes it harder to steal (get bettery out of it or find an area with no cellular connection which are well developed here isnt that easy as just to turn off the device).
It only makes it marginally harder to steal. There are many ways to defeat Find my iPhone; turning it off is only one of them. Others:
Remove the SIM
Wrap in aluminum foil
Drop in a shoplifter's bag or backpack that is metal lined
Run the battery down
Connect to a computer and restore the phone
Requiring a passcode to turn the phone off would also make the millions of users whose phone was not stolen very annoyed that they can't easily turn off their phone. -
My IPOD Touch initially had a white screen. I tried correcting this by restoring default settings via ITunes. The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB. I get an error on my PC stating that device attached to USB port is not recognizable. Can anyone help?
Error 1602: Try the following steps to resolve this error:
Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
Follow the steps listed for Error 1604.
This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
Above from:
http://support.apple.com/kb/TS3694 -
my screen is completely white, i've tried holding lock and home buttons as seen on you tube something called 'white screen of death' its goes black (think it switches off) then back to the white screen need help fast please!
If you have not done a factory reset on the device, I recommend doing a complete factory reset.
Factory Reset - Warning this will reset device back to original factory settings.
This method will not erase any MDN/MIN information
Turn off the phone
Press Power + Volume Up/Down at the same time and hold until display will show a triage android screen
Display will show:
Reboot system Now
Apply sdcard:update.zip
Wipe Data/Factory Reset
Wipe Cache Partition
Use VOL Down key to scroll down to "Wipe Data/Factory Reset", press home icon to select option and wipe device.
Display shows "All user data will be wiped out", press VOLUME Up to continue or VOLUME Down to exit.
Press Volume Up
Press Home to select "Reset System Now" - device will reboot
If the problem persist I recommend having a store technician take a look at the device.
Copy and paste the link below into your browser's address bar for the store locator.
http://www.verizonwireless.com/b2c/storelocator/index.jsp -
While launching Mail, I clicked on Safari, to check something while Mail got new emails, but now Mail appears on the same screen as Safari. Is there a way I can return it to it's own screen, please?
I haven't changed any prefs, only clicked Safari as mail was being launched.Sorry... Apple IDs cannot be merged...
I have multiple Apple IDs. Is there a way for me to merge them into a single Apple ID?
Apple IDs cannot be merged. You should use your preferred Apple ID from now on, but you can still access your purchased items such as music, movies, or software using your other Apple IDs.
From Here http://support.apple.com/kb/HE37 -
Sometimes the screen on my iPhone 3GS randomly enlarges so I cannot see or manipulate the touch screen controls. Anyone know what causes this?
Double tap with THREE fingers to turn zoom off. Then, go into Settings>General>Accessibility and turn it off for good.
-
How do I remove "web clips" links to web pages from my Home screen? Holding until jiggle does not produce "X" for deletion contrary to the ipod touch manual
Figured oout that I had restricted deletions of programs.
Settings->General->Restrictions-> (enter your passcode), Turn Deleting Apps ON
Afterward holding an icon until it jiggles will produce the X delete button.
You might want to turn Delete apps OFF after cleaning up. -
When I start up my imac, I get a blue screen. The wheel spin and the screen gets brighter for a second, then the blue screen dims and it repeats with the wheel.
Are you referring to the startup screen which is normally gray with the dark gray Apple logo or are you referring the login screen which is typically blue? If it's the latter you might give this a try:
Clearing Caches to Fix Login Problem
You will need to type some Unix commands. If you are not comfortable with this, I don't know of anything other than a re-install. But if you are careful, you should be OK. I recommend you print this out in a largish mono-spaced font so you don't miss any spaces (or add extra ones). Note that case is important.
Be careful. Some of these commands are dangerous, since you are going to be root.
Start up in Single-user Mode. When this has finished you will see a prompt ending in '#', although there may be other messages. Enter the following commands after the prompt:
/sbin/fsck -fy
Press RETURN. Wait a few seconds for 8-10 lines of output. If the last line says repairs were carried out, repeat this command until you get a message 'The volume <yourdiskname> appears to be OK'. Then continue with:
/sbin/mount -uw /
cd /Library/Preferences
rm com.apple.loginwindow.plist
rm com.apple.windowserver.plist
cd /Library/Caches
rm -r *
cd /System/Library
cd /System/Library/Caches
rm -r *
reboot
Press RETURN after each command.
This should now take you to a proper login screen after the normal boot sequence. You should then Repair Permissions by using Disk Utility (in your /Applications/Utilities folder).
If it's the former then reinstall OS X. For Snow Leopard:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/. -
Hello,I have downloaded photos from my ipod touch following the instructions but it doesn't download videos.Can you help please?
doesn't download videos
I seen so many of these post for windows users.
Try my little "trick" (must be running iOS 4.3 or better)
Download the app "Download Manager Lite" (FREE) or "Download Manager" Full ($ 1.99 USD)
After downloading, transfer it to iTunes
iTunes Store: Transferring purchases from your iOS device or iPod to a computer
After transferring, Go to your iDevice (on itunes), to the apps page, scroll down, you can add/save videos and/or files.
Click on "Add", find the folder of which your movies are being downloaded. Its much faster than syncing from itunes.
You can do the wi-fi transfer, the best part is that you don't have to be connected to the same wi-fi.
You will get 2 different URLs you need to type on your computer. Type the Web URL not the ftp URL. After that, you should have access to the app, without the need of itunes.
Click on Add, find the folder of where your movies are stored, faster than syncing with iTunes.
HOPE THIS HELPS. -
my ipod touch is disabled for 22 million minutes and I want to fix it but I dont want to lose my pictures and everything else. Help please I dont remember the last time I updated it. Idk I think its been a year in an half since I known about it being disabled. What do I do? Im scared to restore it because I dont want to lose my stuff.
You have to restore and thus erase your iPod. that is how it works.
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
Photos
- If they are in an iPod backup then restore from that backup. See the restore topic of:
iOS: How to back up
- If they are in the iTunes backup then get them from the backup by:
Recover iPhone, iPad or iPod photos from backups with Picturescue
- If you used PhotoStream then try getting them from your PhotoStream. See that topic of:
iOS: Importing personal photos and videos from iOS devices to your computer -
After installing the 64 bit version of itunes my iphone still won't sync. I get the explantation that I mobile driver application did not download and i need to remove and reinstall itunes (which I have done numberous times). Any help?
Let's try a standalone Apple Mobile Device Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of why it's not installing under normal conditions.
Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
http://www.apple.com/itunes/download/
Download and install the free trial version of WinRAR:
http://www.rarlab.com/
Right-click the iTunesSetup.exe (or iTunes64setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
Go into the folder and doubleclick the AppleMobileDeviceSupport.msi (or AppleMobileDeviceSupport64.msi) to do a standalone AMDS install.
(If it offers you the choice to remove or repair, choose "Remove", and if the uninstall goes through successfully, see if you can reinstall by doubleclicking the AppleMobileDeviceSupport.msi again.)
Does it install (or uninstall and then reinstall) properly for you? If so, does your device connect without that message now? -
How to Add Partner function in the main screen of the Sales order???????
Hello All,
I am working on ECC 6.00 SD module
I want to add partner function in the main screen of the sales order, that mean add more partner function beside Sold to party and the ship to party to be in the order header, Is it possible and how?
Regards
Jacopo FrançoiseHi
If you want in the sales order , above the sold to party as the box then you need to go for enhancements
Regards
Srinath
Edited by: sri nath on Jun 11, 2008 6:56 PM
Maybe you are looking for
-
Getting an error trying to install Crystal Reports 2008 on a 64 bit Windows
reformatted my computer and now I'm trying to install Crystal Reports 2008 on 64 bit windows 7 box. When the "Registering modules" portion of the install comes up, I get a message that a dll has failed to register. I saw something about not having
-
Hi Experts, I have a problem, we normally purchase various material from xxx country from different vendors, and we have one representative in that country, who confirms us when the vendors will send the material, but we want he should enter order ac
-
Getting the position in SQLLoader using oracle function
Hi. I have a problem to create .ctl file. i have a oracle function to retrieve position CREATE OR REPLACE FUNCTION "TEST_KEYFIELDS" (rec_type IN VARCHAR2,fieldName in varchar2) RETURN VARCHAR2 AS pos_result VARCHAR2(10) := null; BEGIN select '(' || f
-
Print or PDF command closes software
All of a sudden, while going to make a PDF from either the print or export command, my computer fails to print or make a pdf and shuts down the software, in this first case PAGES and then reopens the software. Today i found it is doing the same thing
-
Recently (since I installed version 7) my songs started freezing in iTunes. If I'm listening to a playlist of songs there is no error. But if I have a playlist of 1 song, or if I search for a song in the search box, or when I get to the end of a play