TS1988 Any other suggestions?
textedit just freezes when I try this.
I looked the motherboard over quite well and didn't see anything out of the ordinary. Will bad memory cause it to not post? Anything i missed that would cause it not to post before i trash the mobo?
One other question, i have found this mobo to be a microATX form factor. Do you know if the mounting hole locations differ on other microATX boards? As long as the mobo supports the Celeron D, has the same number of PCI slots (as many as the case has provisions for), and has the same port configurations on the back (for mouse, keyboard, ethernet, etc) would you see any reason why a different mobo wouldn't work? These factory type motherboards are triple what retail kinds are. Wasn't sure if anyone here has experience with both types that can confirm that the mounting holes are in the same location. Not a guru on computers but am looking for any advice or tips from anyone. Thanks in advance!
Similar Messages
-
We just added a new printer and bluetooth connection to our iMac. Now iTunes does not recognize our iPads as devices. Have already tried restarting everything. Any other suggestions?
You can try the steps recommended here: http://www.apple.com/support/ipad/assistant/itunes/
-
When I go to plug in my iPhone 5 to my PC it will charge my phone but it doesn't show up that it's connected to my computer or in iTunes. I have tried just about everything that I can find in the support discussions but nothing has worked. Any other suggestions?
If you have carefully follow ALL of the steps in that article, you are using a USB port directly on your computer and not a USB hub (don't use a front port on a tower or desktop either, as they are an internal hub) and you installed iTunes correctly using an Administrator ID and you have tried disabling your antivirus and firewall then there is no hope of it ever working. Look at the tip again, and go through it carefully, not skipping any steps.
Note, BTW, that an iPhone will not show up on a computer, only in iTunes. If there are photos in the Camera Roll then it will appear in Windows as a digital camera only. -
I need to access (Ultra) scsi-2 68 pin drives but the card is dead. Is there an adapter/converter out there somewhere like my IDE to USB for this? Any other suggestions appreciated.
Might be hard to find, but long ago there were a couple of Firewire<->SCSI adapters, if you have USB2 those might be available also...
http://www.ratocsystems.com/english/products/FR1SX.html
http://www.ratocsystems.com/english/products/U2SCX.html
http://www.ebay.com/sch/i.html?_sacat=0&_nkw=scsi+to+firewire&_frs=1
I think Belkin made one also.
Might be far cheaper to buy an old Mac or even PC with SCSI. -
After updating my iPad 2 to iOS 6, I cannot connect to my router. I have turned the router off, left off for a considerable time, turned the iPad off and on, reset the network settings, nothing works. Any other suggestions? It is obvious many others are having similar problems, so the iOS 6 looks like a loser.
I have just upgraded from a 3 to a 4S and now I can't connect to my wifi. I've tried everything, resetting network settings, switching to boot, renewing lease, rebooting, turning off cellular data etc etc. nothing works!! Very frustrating!
-
Apple TV is continuous loop after accepting to download and install of the latest version of software ( sept 21) has been for several hours I have unplugged and hoped for some sort of reset or at least the chance to start the download again! Any other suggestions?
Same thing with me. Shows apicture of hooking up to USB which I did in iTunes then it told me it could not be restored
-
Any other suggestions to resolve the error, "cannot connect to the itunes store" ?
Hi paul.labiche,
When having iTunes Store connectivity issues, the following articles provide the best solutions:
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/TS3297
Thanks,
Matt M. -
IPad wifi connection drops - have tried evereything - any other suggestions
Hi all,
I'm experiencing the connectivity issue with my iPad whereby randomly it will stop transmitting data (ie cant go on the Internet). The Wifi symbol is till shown, but there is no data throughput whatsoever. To fix, I have to turn off the wifi on the iPad and turn it on again.
There doesn't seem to be any consistency to when this happens. It isn't related to coming out of sleep or the type of apps I am running. sometimes it will happen in quick succession, other times it won't happen for a few hours or maybe until the next day.
There are two iPhones, a Mac mini and and Vista laptop on the same network and none of them experience this problem. The router is a Sky broadband wireless router. It is set to WPA security.
I have tried:
- upgrading to firmware 3.2.2 and doing a restore
- resetting network settings on iPad
- restarting router
- changing channel of router (have tried 4 different channels so far)
- switching router from mixed (b/g) mode to just g
- forgetting network and reconnecting on iPad
- moving closer to router
- disabling auto-brightness
- setting brightness to maximum
- changing DNS on iPad
I have also tried most tips on this page with no joy:
http://appletoolbox.com/2010/04/special-report-fixing-ipad-wi-fi-issues/
It just seems like nothing is going to work, and I am considering returning this to Apple in the hope of either a replacement or a fix. This problem is really annoying and clearly and issue with the iPad as many other devices have no problems. Even if a replacement router may fix this, clearly the iPad is at fault here.
Does anyone have any other suggestions? If not, what do you think will happen if I take this back to Apple? Perhaps I can get a guarantee that they'll swap it with the next-gen iPad when it comes out?
Looking forward to your advice, thanks for reading.I don't have any real words of help except to say I went through something similar with an iMac. It would drop and pick up the wireless signal repeatedly but often sat there unable to connect. That was solved by something weird, like turning off the "show on screen" option for the airport wireless signal. I don't think you can alter that setting on the iPad though. My point is, if this was a problem out of the box I could see it being the iPad and that maybe getting a replacement unit would work (my wife recently bought a cheap B&N reader that would not access the wireless network, replaced it and everything worked). But if this is a problem that developed over time or just started out of the blue, then maybe it is a corrupted file or something that could be fixed with reinstalling the system. I know when you sync an iPod and iPhone with iTunes you have the option of wiping everything and reinstalling, so I am assuming it's an option for the iPad too. If you haven't tried reinstalling, perhaps that can be a next step.
Good luck!
Good luck!
P.S. -
Help. My iPad email screen went blank. I have rebooted, reset and deleted and reinstalled my email accounts to no avail. Any other suggestions?
Restore from iTunes. It is hard to say if you want to backup or rather revert to an old backup. I would recommend to save the previous backups to a safe place and then backup the current state and later test the backups incase your iPhone comes back to proper life.
-
I tried all suggestions fo a grayed out wifi toggle and nothing seems to be working. Any other suggestions?
I had this problem last month. I ended up having to get a new iPhone 4S. It's a very, very common problem and in my opinion it should be covered by Apple for free since it is so popular and is an obvious hardware defect especially in the iPhone 4S.
So I suggest you order a new iPhone ($230 with no warranty) ($50 with Apple Care+). And while you wait for your new iPhone to come you could back up your iPhone and try some of the YouTube fixs. I put mine in a plastic bag (off with no air in the bag) in the freezer for 30 minutes, pulled it out, turned it back on, let the iPhone thaw out in the bag, and it then worked again for over a week before it died again. But I would only try that if you knew you had a new iPhone on the way. My cellular, Wi-Fi, and Bluetooth all went out so I had nothing to lose. -
monitor too faint to read. the greays on my monitor are so faint, they're almost impossible to see. especially the numbers of the dates in ical.
i've gone to system preferences and contrast controls. but no luck. any other suggestions? thank youThank you. I didn't know about the universal access adjustment. All the way left is a little better, but still much fainter than on my own imac. I'm not sure why apple uses grey typeface, but it's so faint on this imac monitor that it was difficult to find the "reply" option on this post. Are there any other suggestions? thank you
-
Any other suggestions?
Hi Friend,
Which kind of account you are using?
If you are using a business account （ for example [email protected]) you must set POP account info properly, filling all the blank fields (name, email address, description, password, Host Name, user's name, SMTP). Just one field blanked causes error in sending/receiving.
If you are using a default account (iCloud, Yahoo!, Hotmail...), fill all the blanck fields (Name, Email account, Password, Description） and sign in.
If not works, delete the account and sign in again
Hope it will be helpful -
I did the restore through Itunes and it still says Ipod disabled - Any other suggestions?
I did the restore on my Ipod through I Tunes and it still says it is disabled - Any other suggestions?
If you are talking about the screen-lock passcode, thate means that the restore never successfully completed.
Try disabling the computer's antivirus and firewall.
- Next try the manual install method of:
iDevice Troubleshooting 101 :: iPhone, iPad, iPod touch
Place the iPod in recovery mode after the firmware download is complete and then restore using the instructions in the article. Sometimes recovery mode timeouts and returns to disabled before the firmware download is complete.
- Then try on another computer -
I can't enable the ownership of my back-up volume via get info. Any other suggestions?
Hi people, My external hard drive is not working well. When I try to make a time-machine back up a window pops up: ‘Mac-OSX can’t repair the disk. You can still open or copy files on the disk, but you can’t save changes to files on the disk. Back up the disk and reformat it as soon as you can’. So now I am trying to copy my back-up files to another disk so I can reformat it. But when I try to do that, the following text appears: The backup files can’t be copied because the backup volume doesn’t have ownership enabled. The problem is that I can’t enable the ownership of the back-up volume.
ALF316 wrote:
Yes its my Time Machine disk that’s damaged. What can I do now? Format the disk and loose all my back-ups?
You may be able to restore individual items, or even an entire backup, as long as you don't happen to hit the damaged area(s). But yes, your only real option is to erase the disk and start over. When you do that, you might want to take the time to have Disk Utility write zeros to the entire disk (see section (b) in the blue box of #1 in Using Disk Utility if you're not sure how to do that) -- if that fails, you know the disk itself is failing and must be replaced. If it succeeds, the drive may be ok.
And how can I prevent this in the future. I know at least I had to have a second back up disk but I never did that.
You probably don't know yet what caused it. If it's the disk failing, obviously you need a new one. Other things that can cause disk corruption are power blips, being disconnected improperly, or your Mac crashing or losing power while the disk is connected, especially during a backup.
For power problems, the best solution is a U.P.S. (battery backup) system. A good surge protector will protect against power spikes, but not dips or sudden loss of power.
I allready tried several times to change ownership with Get Info but I can’t. I don’t see a checkmark and the
section isn’t clickable either. Any other suggestions?
The screenshot is of your TM drive. The message is about the drive you're trying to copy to, such as: -
Just rented a movie on apple tv and it keeps starting and stopping every few minutes. have restarted in settings. have unplugged and replugged apple tv. any other suggestions?
The first thing to check would be your internet download speed, you can do this at www.speedtest.net.
1080p HD movies require a recommended speed of 8 Mbps, 720p HD movies require a recommended speed of 6 Mbps, while SD movies require a recommended speed of 2.5 Mbps.
Maybe you are looking for
-
ElementsOrganizerSyncAgent.exe - No Disk ERROR message
I keep getting this error and I'm not sure why...Photoshop Elements 8
-
Can't find programs in the CC app
Could someone help me with downloading Lightroom 6/CC? When I launch the CC app on my computer, and press "Install Adobe apps", nothing happens. Sometimes even the CC app crashes and the app turns black... Does anybody have any solutions?
-
Budget Line Item for Internal Order was disappeared
Dear GURU, I have the problem when posting budget via Tcode KO22 KO24 and KO26. When posting budget in the first time, the system was not generate budget document. But it was created when I post budget again in the second time. Please tell me what ha
-
@Creating a new wage type in an Infotype
Hi, How do we go about creating a new Wage Type for an Infotype? (HR module)
-
ALSB - Java Callout (.jar using commons-httpclient-3.1)
Hello everyone, I'm having a not so funny problem. I made a Java class, that will be called by a Proxy Service (Java callout). I'm using the commons.httpclient-3.1.jar (+ codec and logging). Here's the code: package util.http; import org.apache.commo