TS2756 Here is what worked for me for wifi

Change your hotspot device name if it looks strange as a wifi SSID. eg use "John iPhone" instead of "John's iPhone"
Got to Settings > FaceTime and scroll down to the bottom.
Turn Use Cellular Data to off for FaceTime
Turn your phone off. (I think this might be important).
Turn the phone back on.
Go to Settings > General > Cellular > Personal Hotspot and switch it on.
Try to connect to hotspot again over Wifi
(Not tested) It should be OK to turn Cellular data back on for FaceTime, if you really need to.
Repeat steps above if problem returns.
So I think some kind of clash with FaceTime was the problem. It might explain how I was able to connect through my iPad (but not my iPhone). I had never used my iPad for FaceTime.
My iPhone is 4s, running IOS 6.1.3, although this issue has been around for a few IOS versions.
Hope it helps someone.

Agreed!!
Same story......after waiting over 36 hours for activation, finally called 877-800-3701 AGAIN (probably the 4th or 5th time) and got an incredible CS person named Michelle who could not have been more helpful. She actually took the time to look at my account, saw that it was ready to activate, and went through all the steps to manually activate it. Whole process took about 45 minutes, but it was with someone from AT & T instead of waiting around all day for some magical email. Now, iPhone works like a charm and was worth the wait.
So to all still waiting for activation, keep calling the 3701 number. And keep doing it until someone takes the time to help you. It really does work......

Similar Messages

Here's what worked for me...

Here's what worked for me:
1) I opened iTunes and in Options, I selected iTunes as the default music player for my computer (it wasn't). (I even uninstalled RealPlayer and WinAmp.)
2) I uninstalled iTunes and iPod, and reinstalled using the newer versions on the Apple site.
3) I basically followed this advice:
http://discussions.apple.com/thread.jspa?threadID=291183&tstart=0
Which was basically to leave my iPod connected to the computer while rebooting. The first 2 times it didn't work, I forgot to put iTunes in the start menu, so that it opens when I reboot. I put iTunes and iTunes Helper (whatever that is) in the start menu (I used WinPatrol to do so, available for free here: http://www.winpatrol.com/), and then rebooted, and after a couple of tries, like magic iTunes opened, recognized my iPod, and updated it, and then, for the first time, without freezing my system, told me it was okay to disconnect.
It even worked while still running my regular systray apps, like McAfee VirusScan, Ewido Anti-Malware, Microsoft AntiSpyware Beta, and SpywareBlaster, so those were not the issue. I get the impression you need to boot it once so it recognizes the iPod and does that handshake thing, and hopefully after that it'll always do the same. We'll see...
I hope this helps someone, b/c its been a frustrating day working through all this, and I know a lot of others are still trying to get it solved. And thanks to jcog for posting his solution, that helped me, and hopefully this will help someone else...
c.
iPod Video, 60GB Windows XP

it worked until the next time I synced the iPod, and then back to the freeze up. Next thing I tried was this Microsoft help page:
http://docs.info.apple.com/article.html?artnum=93976
which advises on several things, all of which seem helpful, but the thing still freezes up. I can sync the iPod, then the system freezes and I have to reboot. So, I now believe Apple will have to issue a patch for these bugs when using the new 5G iPods with WinXP.
c.
iPod Video, 60GB Windows XP

Here's What Worked!! Yeah! 1402 was conquered!!

I am not an expert but this is what worked for me. I kept getting an error of 1402 when I ried to install quicktime stand alone. The reason I tried to install this was because I would get a message during the general installation that said Itunes would not open because I had quicktime 6.5 installed instead of 7.02. I tried everything mentioned including changing permissions in the registry, installing windows install cleanup, etc., etc,. What actually worked was going to start then run typing in regedit and deleting everything that said quick time. After doing that I disable Norton and dowloaded the quicktime standalone and it worked. I then dowloaded Itunes and it worked. I didn't lose any music or anything. I hope this helps, but please check with someone who knows more before you take my advice. I am finally back.

it worked until the next time I synced the iPod, and then back to the freeze up. Next thing I tried was this Microsoft help page:
http://docs.info.apple.com/article.html?artnum=93976
which advises on several things, all of which seem helpful, but the thing still freezes up. I can sync the iPod, then the system freezes and I have to reboot. So, I now believe Apple will have to issue a patch for these bugs when using the new 5G iPods with WinXP.
c.
iPod Video, 60GB Windows XP

Audio Dropout - Fixed! -Here's what worked for me

Hardware: Airport Express, Intel iMac 10.4, Belkin N1 Router
*The problem:*
When streaming iTunes music to my Airport Express, audio cut out after a few seconds.
Troubleshooting:
1) Moved Airport Express closer - no effect
2) Uprgraded firmware - no effect
3) Restored Airport Express to factor default - no effect
4) Then I wanted to see if there was some WiFi interference. Connected my computers to my network by ethernet rather than WiFi. Set my Airport Express as a new network (Apple Network XXXX), then connected my computer to the new network rather than my existing WiFi network. It worked! This told me there was something with my network causing the problem.
*The fix:*
So I went in to settings pages for my router to see what I could change. I ended up switching from 'g+n' to 'bgn'. I also disabled the option for 'protected mode'. Thats it. Everything is fine now. Hope maybe this helps someone.

it worked until the next time I synced the iPod, and then back to the freeze up. Next thing I tried was this Microsoft help page:
http://docs.info.apple.com/article.html?artnum=93976
which advises on several things, all of which seem helpful, but the thing still freezes up. I can sync the iPod, then the system freezes and I have to reboot. So, I now believe Apple will have to issue a patch for these bugs when using the new 5G iPods with WinXP.
c.
iPod Video, 60GB Windows XP

Finally, activation success! Here is what worked for me:

After 38+ hours
I bought 2 iPhones. For both of them I was porting a number over from Sprint (from the same account).
Selected the Family plan for activation.
Within an hour, the first iPhone was activated for all but incoming calls (My wife's phone).
The second iPhone I got the dreaded "Your activation requires additional time to complete"
I called every number that I could find. Almost everyone told me to wait. There were 2 calls where people actually did something to my account.
Here are the people who actually appeared to do something:
Called 1-877-777-4189 (I think. Either that or it was 800-331-0500)
Was answered immediately. Spoke with Nancy who transferred me to number porting services. (Which she said the number for porting services was 1-888-898-7685, so I would recommend calling them directly)
I spoke with Stephanie Engel (sp?) at number porting services.
She found that my Sprint number had not yet been transferred over properly. I had to give her my IMEI number off the back of my phone and the number off of my SIM card. After I gave her those she said she was able to activate my sim card. However it didn't change anything about the state of my iPhone waiting to activate. She transferred me to some iPhone activate people who were unhelpful.
Then I called 1-877-800-3701
Select option 3
Enter your order ID # as requested.
For mine the computer said that they needed additional information.
Then it put me on hold for a customer service rep.
I was on hold for a long time (30-45minutes)
Finally got a customer service rep.
He tried to activate it, and the first time it didn't work.
He had to put me on hold several times, had me power off and power back on my phone several times. Eventually he did something that made my phone activate. YAY!!!
If you get someone who tells you to wait longer, I'd recommend hanging up with them and calling back till you get someone who will try to help. There are people at this number who can help.
The customer service rep never asked for any additional information, so it was something he had to do to activate it manually.
I think the porting number issue had to be fixed before talk to the people at 1-877-800-3701 would help.
There is also a thread on at&t about this:
http://forums.wireless.att.com/cng/board/message?board.id=apple&thread.id=1453&v iew=bydateascending&page=1

Agreed!!
Same story......after waiting over 36 hours for activation, finally called 877-800-3701 AGAIN (probably the 4th or 5th time) and got an incredible CS person named Michelle who could not have been more helpful. She actually took the time to look at my account, saw that it was ready to activate, and went through all the steps to manually activate it. Whole process took about 45 minutes, but it was with someone from AT & T instead of waiting around all day for some magical email. Now, iPhone works like a charm and was worth the wait.
So to all still waiting for activation, keep calling the 3701 number. And keep doing it until someone takes the time to help you. It really does work......

Having trouble with your iphone6 not connecting to your car? here is what worked for me

Back up your phone!!!
Go to Settings>General at the bottom of the screen hit “Reset.” On next screen select "Reset All Settings." This will reset your locked screen, your internet passwords, Touch ID & Passcode, your zoomed view, battery percentage, etc. You won’t loose any apps or docs. Just go back and change them as you did when you first got the phone. Delete all the Bluetooth devices on both in your Car and on the iPhone (on the phone: go to Bluetooth>My Devices, click on the “i” at the right and click on "Forget This Device"). Shut down both the phone and the car. Restart the car and the phone. “Pair" your phone. Shut the car off and restart. Give it a few minutes to allow the car to update the phonebook.
This worked like a gem.

Agreed!!
Same story......after waiting over 36 hours for activation, finally called 877-800-3701 AGAIN (probably the 4th or 5th time) and got an incredible CS person named Michelle who could not have been more helpful. She actually took the time to look at my account, saw that it was ready to activate, and went through all the steps to manually activate it. Whole process took about 45 minutes, but it was with someone from AT & T instead of waiting around all day for some magical email. Now, iPhone works like a charm and was worth the wait.
So to all still waiting for activation, keep calling the 3701 number. And keep doing it until someone takes the time to help you. It really does work......

Snow Leopard Printing Woes - what worked for me

I found many print problems posted EVERYWHERE from every printer manufacturer and model and many solutions and some worked for some people. None worked for me.
I have a HP Laserjet 2100M, which is old, but is listed as compatible with SL. I cannot part with it, as it is a true laser printer, not a monochrome, which means when I need to colour separate say a blue and red document, it prints as solid, not grayscale. It has printed 44,820 pages for me over the years, with only laser cartridge replacement as an expense. As well, I cannot find anything but monochrome for a replacement.
It worked on my old iMac G5 running Leopard, however, when I got my new iMac running Snow Leopard, I got "Printer Offline" message and it would not go online and while some solution ideas got it to print, sometimes, it was only good for one or two jobs and then would stop again, or it would say printing and nothing would print.
Here is what worked for me:
I disconnected my printer's usb and power supply, reset printer system.
Went to Macintosh HD-Library-printers-PPDs-contents-resources and deleted all of the HP Drivers.
I got my HP 2100 series driver from my old iMac and put that back in the resources folder and emptied trash.
I shut down my computer.
Replugged in power to printer.
Started up computer.
After fully launched, I connected my USB cable for the printer. I went to add printer and it came up right away and said new software update was available for my printer AND I SAID NO to updating. In selected my driver, and...
My printer and I have reached a compromise!
It still says offline, however, everything is printing anyway... this I can live with.
I also found this link, which I will only try if I encounter any other disruptions
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&task Id=110&prodSeriesId=385457&prodTypeId=18972&prodSeriesId=385457&objectID=c018677 22
At some point I printed a Self Test/Configuration page which has I/O Port Status as
USB STATUS - not ready
and Appletalk Status - Ready
which is probably a good clue, however, I have been printing successfully for 15 hours and my hair is starting to grow back.

The HP document appears to solve your issue. When your hair starts falling out again, use it.

TS2756 iam using iphone 4S with win 7 PC and i cannot connect to the internet through my phone but i tried with my other 4S and it works but what should i do for the first iphone 4S???

iam using iphone 4S with win 7 PC and i cannot connect to the internet through my phone but i tried with my other 4S and it works but what should i do for the first iphone 4S???
as i said i have two iphone 4S,,,,,
1st one --- has os 5.1
2nd one has os 6.0
i tried 2nd one with carrier reliance gsm nd it works with that personal hotspot setting using USB...
but i want to connect the first 4S with carrier TATA DOCOMO GSM but its not working with the same USB feature????
plz reply asap...!!!
thnxxx in advance!!!

If not this:
iOS: Wi-Fi or Bluetooth settings grayed out or dim
One user reported that placing the iPod in the freezer fixed the problem.
Also heating sometimes works. See:
Why can't I select my wifi settings?
A trick that works frequently with iPhones:
Settings > AirPlane Mode ON, Do Not Disturb ON
Power down and wait 5-10 minutes
Power up
Settings > AirPlane Mode OFF, Do Not Disturb OFF
If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
Apple Retail Store - Genius Bar
Then:
Does the iOS device connect to other networks? See other networks? If yes that tends to indicate a problem with your network.
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

TS4268 what apple write here is now work for me. If anyone know how to activate imessage on iPhone 5 ios 7.1.1 please kindly share how?

Since i upgarde my iPhone 5 to the latest ios 7.1.1, it doesn't work on iMessage. I've tried to follow the instruction posted by Apple but it still not work for me. It appear " iMessage unsuccessful activation" after i waiting for activation for a while. If anyone know how to get it successful please kindly share, HOW ?

I should also add: There's no pending downloads in the iTunes store on my device or App store. There are some pending downloads linked to my account, but they have been there for quite a while and have never been a problem before. Additionally, if these apps WERE the issue, I figure they would've begun to download on my device after I succesfully typed my password in.

HT1695 My wife is working in London for 5 weeks and for some reason her ipad will not connect to btfon or btopenzones at her digs, but she has a ethernet socket, so can a wifi only ipad2 be connected to the internet via an ethernet cable

My wife is working in London for 5 weeks & staying in digs, so we thought it would be a good idea to buy an ipad2 so we could skype each other, she could watch movies from the icloud, access skygo etc,and it wouldn't be as bulky as a laptop. All fine if you can get wifi, but for some reason her ipad cannot locate any btfon or btopenzone hotspots (or provider), IN LONDON??!! We can access them at home in a little village in Northern Ireland. Her digs have an ethernet socket, is it possible to connect her ipad to this socket via an adapter?

No. She will need to come up with an alternative way to connect. A mobile hotspot perhaps.
Finding some way to connect to these hotspots would be the ideal situation. I know that you realize that. We know nothing about what is happening, but if you can explain in some detail, maybe somebody here can help.

Express not showing up..What worked for me...

After my 1st generation Express died last week, I got the new 802.11n-enabled unit. I was able to use Airport Utility to set the device up initially, but after rebooting the unit, it disappeared from my network, a WPA protected WDS-type with one Extreme b/g unit acting as the main unit, never to reappear. Numerous resets appeared to be fruitless, even the hardware reset where you hold the reset button down as you plug in the unit did not work.
After reading a bunch of posts on here, I finally got my unit to work. Here's what I did.
First, I did a "hard"-reset on the Express by holding down the reset button till the light started to flash amber, then releasing it. After about 30 seconds of solid amber, the express showed up in Airport utility. I copied its Airport ID number shown. Next I got the same information for the Extreme base station, which by the way, always showed up in AU.
I opened up the config window for the Extreme base station, by double clicking on its icon in Airport Utility. I then verified that it was set to be part of a WDS, confirmed passwords, etc and then manually added the Express's Airport ID # in the box for remotes. Clicked the update button and let it do its thing...
Now here's the trick... Power down your airport card, and plug the Express into your computer with an ethernet cable. At this time the Express is probably blinking amber slowly. Wait a few seconds, and then look for the Express in Airport Utility, (you may have to restart Utility, or at least hit the rescan button). My Express was now available for configuration. I followed the procedure as outlined above for the Extreme base station, although this time when prompted I entered in the Airport ID# for the Extreme base station, and set the Express to act as a remote in the WDS window. Enter security options and passwords to match the network you have entered, and hit the update button.
After a seemingly long restart, the Express showed up in the Utility, with a green light no less! I disconnected the ethernet cable, turned on my wireless card, selected the network and voila! it works. Checking AU showed both units as expected, with each one now fully updatable from their respective configuration windows.
So in summary, it appears that the newer Express units that are running 7.3.1 firmware, or those that have been updated to this firmware, have a bug that doesn't allow wireless configuration from an initial state. The 1st configuration needs a direct ethernet connection to "take". In addition, it seems Apple's instructions on doing a hardware reset (the one that resets unit to factory defaults by plugging in the unit while holding the reset button) does not work with the n-enabled boxes. This method did work for the b/g units however. There is a "soft"-reset (hold the reset button in for a second or two which pretty much is the same as un-plugging and re-plugging the unit) and the "hard"-reset, which I outlined above.
I apologize if this is a long winded post, but I hope that I may have been able to help some people out who appear to have been having the same problem that I had.
Good luck!!

Yes, the same thing has happened to me. My internet connection was working fine, but I couldn't see my Airport Express in the Admin Utility nor could I see my remote AirTunes speakers in iTunes. After a restart, everything came back to normal. So if anyone else is facing something similar, try that before panicking.
iMac G5, iBook G3 Mac OS X (10.4.5)

QT7 installing(what worked for me)

There have been numerous post's about having problems installing QT7. I had the same problem and got the same errors that other's are posting. There doesn't seem to be a accurate solution to this problem of wether it is the Microsoft OS or the Apple installer. So I will post what worked for me in finally getting QT7 standalone to install.
I downloaded SP2 for XP pro to get Windows Installer 3.1, I previously had version 2.0
I then removed QT from the computer using the add/remove control panel. And then went to the Folder Options control panel and selected, show hidden files and folders. Then went to Start>search all files and folders, QuickTime, and removed all that was left behind.
I then went into the registry, Start>run>type in regedit>OK
In the registry, I first went to HKEYLOCALMACHINE+SOFTWARE and deleted Apple Computer, Inc. And then hit the F3 key on the keyboard to get the next QT registry key to appear delete it and hit the F3 again for the next one to appear, and keep repeating this until they are all removed.
I then went to each registry listing-HKEYCLASSESROOT, HKEYCURRENTUSER, HKEY_USERS, HKEYCURRENTCONFIG
And would click on one to highlight and then go to the Edit menu, click find, type in QuickTime, hit the enter key on the keyboard. Delete the QT registry entry, and hit the F3 keyboard key for the next one to appear. I went thru this procedure until everything QT was removed from the computer.
Note: the registry is very risky to go into deleting keys. It would be wise to go to the microsoft website to get further info before attempting anything in it!
This worked for me. QT7 standalone then installed. I also downloaded Windows Installer Clean up Utility. Ran it and found QT 7.02 in there and removed it.
goodluck

I don't know why this is not installing on some computers and not others. It took me 2 or 3 days to get it to.
The only things I did was update to SP2 to get Windows Installer 3.1 Remove everything QT from the computer as I previously mentioned.
In Install Shield I downloaded driver 7. I had read a article about having the same number driver in Install Shield as the first number of the version of the progarm you are trying to install. In this case it is 7.0.2, so I downloaded 7. I did not bookmark the link to this. So I don't know now where it is on the web. But after doing this it still did not install.
It didn't install to after I removed QT from the computer and ran Windows Installer Cleanup Utility. And removed QT which was in there. Here is the link to download the installer cleanup utility.
http://support.microsoft.com/default.aspx?scid=kb;en-us;290301
Also this link my be of interest.
http://consumer.installshield.com/kb.asp?id=Q108393
I don't know what it was exactly that got it to install. But this is all I did. If you have any other questions or compare what I have on this computer your welcome to ask.
I realize it is fustrating and wish I could have been of more help.

AE n - What worked for me

I am an experienced AE user and owner of four of the 1st gen "g" type which I use with an AX "n" base station to stream music wirelessly around my house. I have previously gone through the setup procedure a dozen or more times and if you want to add an AE to an existing wireless network, the easiest way is to hook it up to your LAN by ethernet and configure it that way. I decided to try a new AE "n" to see if I could improve reception distance and performance and have been suffering the same struggles that others have posted here. After hours of experimentation, everything seems to be working. I tried so many different things it's hard to tell exactly what worked, but here is what I think did the trick.
1. Disconnect all wireless clients from the base station.
2. Change the network security of the base station to WPA/WPA2 and restart.
3. Configure the AE "n" first, connecting by ethernet. You may have to do a reset using a paperclip. Configure it using WPA/WPA2, making sure it is acting as a bridge and using DHCP to acquire an IP address. Restart, leaving it connected by ethernet. Check configuration and restart again, disconnecting the cable. IT WORKS !!!
4. Reconfigure the other wireless devices the same way: connect by ethernet; plug in; reset with paperclip; configure using WPA/WPA2, bridge, DHCP; restart with ethernet; restart again unplugged.
So far all five AEs have been working fine for 24 hours.

it worked until the next time I synced the iPod, and then back to the freeze up. Next thing I tried was this Microsoft help page:
http://docs.info.apple.com/article.html?artnum=93976
which advises on several things, all of which seem helpful, but the thing still freezes up. I can sync the iPod, then the system freezes and I have to reboot. So, I now believe Apple will have to issue a patch for these bugs when using the new 5G iPods with WinXP.
c.
iPod Video, 60GB Windows XP

I have a new iMac. I have set up a user page for myself, for my wife and an administrator page. My question is my wife needs files from my user page transferred to her page. What's the easiest way?

I have a new iMac. I have set up a user page for myself, for my wife and an administrator page. My question is my wife needs files from my user page transferred to her page. What's the easiest way?

I've done this by dragging files from my user page to her drop box. In Finder, drag the required files and hover over the hard disc icon in the navigation bar on the left. As you hover, it will open another finder window showing the contents. Work your way down these windows into <Her username | Public | Dropbox>. Drop the files into the dropbox. She can then retrieve them from her user page.
Good luck,
Stephen

Wifi dropping - What worked for me.

I know there are a lot of wifi issues out there but here's what was happening for me.
My iPhone 4 would drop the wifi connection enough so that I just turned off wifi completely and used 3G all the time. This has been happening for a while now. Then for Christmas I was lucky enough to get an iPad, which had the same problem. Would work ok for 5 minutes or so the wifi would drop. Signal said I had a connection but it wouldn't work. But since I only have a 2gb plan on the iPad I needed to be able to use wifi.
I read the numerous threads here and tried various things without success. I googled the problem and found a PC Mag article on the subject. They recommended 6-7 things to try. The first few I already trying with no luck.
Then it suggested changing your router settings to not broadcast in multiple ways (802.11G, A, N). My Belkin router was by defaut using all available methods. I couldn't use N-only as recommended in the article because I have an older notebook that doesn't recognize anything past G.
So I changed it to broadcast in G only and so far that seems to have solved the problem. It's only been one day but it's already way better than it's ever been.
So if you have having similar issues and haven't tried changing that setting it's worth a shot. There's no risk to trying it. I did and now I'm very happy with both my iPad and iPhone.

What iPad update through itunes are you referring to please? I just synched and it says 3.2 is the latest update software for the ipad.
Thanks
JW

TS2756 Here is what worked for me for wifi

Similar Messages

Maybe you are looking for