TS3274 iPad 2 stuck in recovery mode

iPad is stuck in recovery mode. I don't want to restore and lose data, is there a way to do this?

Restore ur iPad to iOS 5 or 6( if u have downloaded)
<edited by host>
Then connect your iPad to your computer ,open iTunes ,click on your iPad's name in the left column ,hold the shift key and press restore , chose the file u downloaded , Wait for the restore to finish.
Then set up your iPad as a new iPad .
Here you go, Now your iPad will be perfectly fine..

Similar Messages

  • I tried updating to iso 8.0.2 and now my ipad is stuck in recovery mode and will not do anything. it will not reset.

    I tried updating to iso 8.0.2 and now my iPad is stuck in recovery mode and will not do anything. it will not reset.

    RECOVERY MODE
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.
    3. Repeat the process if necessary.

  • My IPad is stuck in recovery mode and now ITunes wont recognize it, what do I do? Keeps giving me a long error message.

    My IPad is stuck in recovery mode and now ITunes will not recognize it, it just gives me this long error message. What do I do, I've uninstalled and reinstalled ITunes.

    Check USB connections
    Related errors: 13, 14, 1600, 1601, 1602, 1603, 1604, 1611, 1643-1650, 2000, 2001, 2002, 2005, 2006, 2009, 4000, 4005, 4013, 4014, 4016, “invalid response,” and being prompted to restore again after a restore completes.
    If there’s an issue with the USB port, cable, dock, or hub, or if the device becomes disconnected during restore, try troubleshooting the USB connection, then troubleshooting your security software.
    To narrow down the issue, you can also change up your hardware:
    Use another USB cable.
    Plug your cable into a different USB port on your computer.
    Try a different dock connector (or no dock).
    Add (or remove) a USB hub between your device and computer.
    Connect your computer directly to your Internet source, with no routers, hubs, or switches.
    If you checked your connections and are still seeing the error message, check for hardware issues.
    Check for hardware issues
    Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
    Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the error message when you update or restore, contact Apple support.

  • My iPad is stuck in recovery mode.  I already downloaded Snow Leopard and am making no progress.  Help!

    My iPad is stuck in recovery mode.  It was suggested before that I upgrade my computer, so I downloaded Snow Leopard and have tried resetting it, but it still isn't working.  What can I try next?

    FORCE IPAD INTO RECOVERY MODE
    1. Hold Sleep/Wake button down and slide to turn off iPad
    2. Turn on computer and launch iTune (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTune and plug.
    5. Release Home button.
    ON COMPUTER
    6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
    7. Select "Restore iPad"...

  • My iPad is stuck in recovery mode, and wont stay turned off in order to use redsnow.

          Alright so my iPad is stuck in recovery mode. I did some research and arrived at redsnow to fix the problem. In order to use redsnow's recovery fix option I have to power down my iPad. When I hold the sleep button though, no "slide to power off" appears, the screen just goes black then reboots into recovery mode 3 or 4 seconds later. Restarting it via holding the sleep and home buttons doesn't do anything. How do I get it to stay powered down? Any advice would be greatly appreciated.

    I believe I may have used the wrong terminology. My iPad screen looks identical to the picture shown in the link, which is what I reffered to as Recovery Mode. I was looking for a way to return to normal functionality, without having to restore my iPad. I have never backed up this iPad and would prefer not to lose any information on it. If this is impossible then I will just restore it and carry on.
    My main issue with restoring it is that I don't want to lose the pictures on it. If the restore doesn't erase the pictures, then I apologize for wasting your time and will be restoring it immediatly. However if I will lose the pictures than I'd prefer any other method of exiting this screen.

  • Our iPad is stuck in recovery mode after attempting to update.

    Our iPad is stuck in recovery mode after attempting to update to latest iOS..Help.

    It IS plugged into the pc. iTunes doesn't even recognize hat any device is connected.
    Reiboot isn't even working. considering trying DFU mode. no idea if that will even help.

  • Ipad 2 stuck in Recovery mode after trying to upgrade with ISO6

    Ipad 2 stuck in Recovery mode after trying to upgrade with ISO6, help!

    Restore ur iPad to iOS 5 or 6( if u have downloaded)
    <edited by host>
    Then connect your iPad to your computer ,open iTunes ,click on your iPad's name in the left column ,hold the shift key and press restore , chose the file u downloaded , Wait for the restore to finish.
    Then set up your iPad as a new iPad .
    Here you go, Now your iPad will be perfectly fine..

  • IPad 3 stuck in Recovery mode while trying to upgrade

    I attempted to upgrade my iPad 3 and received the error message that there was not enough memory. Linked it via USB to iTunes on PC laptop (updated iTunes to latest version). Error message said unable to upgrade the iPad, my only option is to Restore. However, that will erase all my data and settings which I have not backed up. Now I'm stuck. Either restore and lose all or leave iPad as is ... only problem with the latter is that the iPad is stuck in Recovery mode and everything I have tried does not release it. Would appreciate help with this as I now have a non-functioning iPad! Thank you.

    Hello ardsdon,
    Thank you for using Apple Support Communities. 
    I see your iPad is stuck in recovery mode. The following article addresses putting your phone into recovery mode and restoring it. 
    If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support
    Regards,
    Jeff D. 

  • IPad 1, stuck in recovery mode, error 1601, wont turn on or restore/update

    Its a brand new iPad,
    its stuck in recovery mode, it says restore and update but it wont restore/ update because i get error 1601, How do i fix this problem ??? it wont even turn on please help?

    If it were in recovery mode, you would see this
    If its just a blank black screen, follow these steps
    Will not turn on, or will not turn on unless connected to power
    Verify that the Sleep/Wake button functions.   If it does not function, inspect it for signs of damage.   If the button is damaged or is not functioning when pressed, seek service.
    Check    if the Liquid Contact Indicator (LCI) in the headset jack or dock connector is activated or there are signs of corrosion or debris. Learn more about LCIs.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 15 minutes, if:
    The home screen appears: The iPhone should be working. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See   "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    If something other than the Home screen or Low Battery screen appears on the display, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, try resetting it while connected to the iPhone USB power adapter. To reset, press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until either the Apple logo or the battery symbol appears.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Restore the iPhone. Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.

  • Hi so my ipad is stuck in recovery mode.  Once I connected to itunes to install the ios 8 software it says that its eligible for the request build and I tried the sudo nano command and that didn't work either. Please help thanks!

    Ipad mini stuck in recovery mode.
    My itunes is up-to-date.
    Sudo nano command is not working.

    yes i am sure. This are the exact words... "The iPad "iPad" could not be restored. The disk you are attempting to use is full. (Removing files and emptying the recycle bin will free up additional space". i tried some options, hard reset, redsnow, tinyumbrella but still it's stuck.

  • Ipad mini stuck in recovery mode after ios 8.1 update

    i have a first generation ipad mini which usually works fine.  last night the ios update appeared in my settings and i tried to install it.
    i didnt have enough space so deleted some apps and then installed.
    the ipad switched on at the end but said the update failed as i didnt have enough space i needed a little more.  i deleted more apps and attempted to install again
    this failed my ipad is now stuck in recovery mode, it hasn't taken itself out as apples help pages suggest after 15 minutes its been in recovery now for 15 hours
    i have tried to connect to itunes as the screen is telling me to but it will not recover from there either as apparently i can't connect to apple servers my connection isnt working - i assume because others are having this problem as i a using the same pc to post this message so know my network is fine.
    i need help to get out of recovery mode - itunes says my software is up to date so i may have this nightmare software already. 

    i originally tried to install the update using wifi and this did not work.  i think i might just chuck the thing as looking on the boards all my stuff will be lost anyway - i backed up 2 days ago but that is nowhere to be found now in itunes or the cloud kmt

  • HT201210 my ipad is stuck on recovery mode..what to do please help

    ive tried to erase all content of my ipad3 but then it does not want to activate..so i tried activating it thru itunes.but it got stuck on recovery mode...please help

    Follow the instructions below to recover your iPad.
    http://support.apple.com/kb/ht4097

  • My ipad is stuck in "recovery mode" - What can I do?

    I was in the process of upgarding my iPad to IOS 7 and started getting connectivity errors after the download started to attempt to install. The iPad then started restarting every few minutes and it's now stuck in recovery mode. I've updated itunes, but the restore won't finish updating the firmware. What's my next step?

    Recovery Mode: iOS: Unable to update or restore - Apple - Support
    DFU Mode:
    Plug your device into your computer.
    Turn off the device.
    Hold the Power button for 3 seconds
    Hold the Home button without releasing the Power button for 10 seconds
    Release the Power Button but keep holding the Home button
    Keep holding the Home button until you are alerted by iTunes saying that it has detected a device in Recovery Mode
          NOTE: Make sure the device screen is blank and

  • Ipad 2 stuck in recovery mode after io6 update

    I have waited for months to update to io6 because I have been busy, and now that I have, I'm stuck in recovery mode giving me a (-1) error.  Some say that's a hardware error, but it can't be because it coincided with the update to ios6.  Here's what I've tried:
    Rebooting everything
    Tried to recover from mac.
    Tried to recover from windows.
    Tried to recover using different router without wifi.
    Placed in DFU mode.
    Did hard reset.
    Tried to hard reset with uplugging cord during download then reattaching.
    Tried tiny umbrella.
    Tried using different cord.
    Have the latest version of Itunes.
    Went into terminal and deleted file after # that some kid on you tube said to do.
    I'm at my end of searching.  Any suggestions????  I know it can't be hardware because it did this immediatly following the ios 6 update.  Thanks,

    When you do an iOS update certain parts of the hardware are used that aren't normally used. If these fail then you can get an error (-1). The error occurs not because of the content of iOS 6 but the update process itself.
    If you can't get out of recovery mode with all that you have tried then your iPad likely has a hardware problem and needs replacement. Hopefully you are still under warranty.

  • Ipad 2 stuck in recovery mode after updating to IOS 5, Unknow error -1

    Hi Everyone,
    my Ipad 2 is stuck in recovery mode after updating to the latest IOS 5. Tried to restore, it comes up with unknown error -1.
    Ive tried all that I can including the tips given in the apple forums and internet. Please help.

    Hello soccerlime,
    Thanks for using Apple Support Communities.
    The error code "9006" in iTunes when updating or restoring your device indicates that access to the iTunes update servers is being blocked.  Please take a look at the information below to help resolve this error.
    Check your security software
    Related errors: 2, 4, 6, 9, 1000, 1611, 9006. Sometimes security software can prevent your device from communicating with either the Apple update server or with your device.
    Check your security software and settings to make sure that they aren't preventing a connection to the Apple servers.
    Resolve iOS update and restore errors
    Take care,
    Alex H.

Maybe you are looking for

  • Pls All Prof I need HELP !! ADOBE ACROBAT PRO 9.0.0

    Hi all profs am glad to ask you and be wid you in here .. am working in a printing press environment and i'm new user of acrobat 9 i have a problem with printing any b;ack & white PDF document as a gray scale the output is not 100% pure black for exa

  • How to Create a text frame?

    Hai i'm senthil.... i'm just now started working with Adobe Indesign plugin's.. Can anyone tell me how to create a text frame... wat r the steps for creating a text frame? what are the Interface pointers used for creating a text frame... plzz reply m

  • How can I combine itunes libraries for a shared music setup?

    I wanted multiple users on my computer to share the same itunes music folder and library. I put an itunes folder (with an itunes music folder and library data file inside the itunes folder) into the computer's shared folder. I set each users preferen

  • Imposs to upload with iWeb - use iPhoto Photocast & play with Homepage

    I found a way to get pics visible, publishable or visible with eBay etc... It's not enough for most people but it'll work for some... Go to iPhoto and Photocast your pics... They ZOOM online... (Mine did anyway...) Then move the whole folder(s) on iD

  • Changing Security Code in Router

    The Security Code in my WRT54G that Linksys Tech Support assisted getting me wireless network at home. I believe that WEP was used and Saved. Should not WAP Security be used for better security of my home wireless Network and should I go in and chang