TS3274 ipad will not scroll, also to open an app i need to tap 3 xs to get open. actually anything I try to do on the ipad requires 3 taps.

I had closed the cover on my Ipad, when I went to open back up I had a black screen. did a hard reset now I can't get anything to scroll and to open an app or to type anything I have to tap the buttons three times for them to respond.

It sounds like you had Voice Over enabled in the Accessibilty Settings. Are you are able to start the iPad now? It sounds like that is an issue as well.
This explains how to turn Voice Over off and on.
http://support.apple.com/kb/HT4064
You don't need or necessarily want to let the battery run down at all. If you let the battery run down and then recharge, that will not reset the device.
If the iPad is not responding at all, look through this for help in order to get the iPad up and running again, and then you can deal with Voice Over.
http://support.apple.com/kb/TS3281

Similar Messages

  • Firefox often freezes and will not close; also cannot open bookmarks

    After operating normally for a few minutes firefox freezes and will not allow me to open legitimate pop-ups or access another website.
    At the same time my bookmarks folder will not open.

    Which security software (firewall) do you have?
    Did you check the Firefox rules and make sure that is doesn't block Firefox?
    Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
    See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]

  • Please help me with portfolio.I am new in graphic design.I need portfolio done immediately soon as possible otherwise my design advisor will not let me register for fall. I need 15 or 10 artworks to show.Please help me

    Please help me with portfolio.I am new in graphic design.I need portfolio done immediately soon as possible otherwise my design advisor will not let me register for fall. I need 15 or 10 artworks to show.Please help me.

    Farooq,
    If you look at the first one, you should be able to align quite easily as follows, View>Smart Guides being your friends:
    1a) ClickDrag the top flower with the Selection Tool (black arrow) so it is clear of the pointy part;
    1b) Click an empty spot on the Artboard to deselect, then ClickDrag the top flower by its bottom Anchor Point (Smart Guides say anchor when you are close enough to grab it) down to snap to the top Anchor Point on the pointy part (Smart Guides say anchor when you are close enough);
    1c) Do the same for the boroom flower.
    If you look at the third one, to get the triangles and the hexagon sized and aligned precisely, you may, creating them with stroke and no fill:
    3a) Click with the Polygon Tool and select a suitable/chosen Radius and 6 Sides, then Object>Transform>Rotate by 30 degrees (or use the Rotate option in the Transform palette), you may Object>Transform>Reset Bounding Box to have it look nicer;
    3b) Click with the Polygon Tool and select the same Radius and 3 sides, then deselect and ClickDrag the top Anchor Point to snap to the top Anchor Point of the hexagon;
    3c) Object>Transform>Rotate by 180 degrees clicking Copy, deselect, and ClickDrag the bottom Anchor Point to snap to the bottomAnchor Point of the hexagon;
    3d) Select all and Ctrl/Cmd+G to Group (for alignment purposes, you will know why if you try without grouping, see below).
    To create full symmetry, you may use circles rather than almost circular ellipses; you may:
    3d) Click with the Ellipse Tool and select a suitable/chosen Width = height;
    3e) Object>Transform>Move a copy vertically by the Height (= Width) twice (or you may Ctrl/Cmd+D to repeat), to get three circles over one another with no gaps;
    3f) Select the topmost and bottommost ones and Object>Transform>Rotate a copy by 120 degrees twice, to have all the seven circles precisley touching one another; you may Group them, but it is not necessary.
    To have everything aligned, just:
    3g) Select everything and click Vertical Align Center and Horizontal Align Center in the Align palette; you may click the pointy group or the circles ojnce more before aligning if you want to keep it in place (that will make it the key object that the other set is aligned to).
    These ways may also help you further.
    Edit: About half an hour after midnight here. High time to attend to other duties, before the sun is up.

  • I cannot open iCal because of a problem. Can anybody help me? The computer will not allow it to open and sends a message to apple each time. The icon has gone from the dock, but ical works on my iPad and I am afraid to sync it with my computer.?

    I cannot open iCal because of a problem. Can anybody help me? The computer will not allow it to open and sends a message to apple each time. The icon has gone from the dock, but ical works on my iPad and I am afraid to sync it with my computer in case it wipes everything .

    I have the exact same problem. I have not changed anything. This is probably a bug or something that has gone bad with Mac OS X (10.7.2). I have not found any solution for this on the web.
    MacBook Pro, Mac OS X (10.7.2).

  • Bookmark sidebar will not scroll and bookmarks will not open in Firefox 7 or 8

    Cannot get past Firefox 6 without probelms with Bookmarks sidebar. Sidebar will not scroll and folders will not open to reveal bookmark contents. Had this problem with Firefox 7 and again with Firefox 8. Would like to use latest version for security reasons, but it is useless to me if I can't access bookmarks

    Try:
    *http://kb.mozillazine.org/Corrupt_localstore.rdf
    Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
    *Don't make any changes on the Safe mode start window.
    *https://support.mozilla.com/kb/Safe+Mode

  • Bookmark sidebar will not scroll and bookmarks will not open in Firefox 7

    After updating Firefox to version 7, I am unable to use the Bookmarks sidebar. The sidebar will not scroll, nor will any of the bookmarks respond to a mouse click to open them. Had to uninstall 7 and go back to 6. Any fix for this?

    A possible cause is a problem with the file places.sqlite that stores the bookmarks and the history.
    *http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
    *https://support.mozilla.com/kb/Bookmarks+not+saved#w_places-database-file
    Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
    *Don't make any changes on the Safe mode start window.
    *https://support.mozilla.com/kb/Safe+Mode

  • A text like box has appeared on the screen of iphone and have to double click everything also it will not scroll down or across how can I fix this?

    A text like box has appeared on the screen of my iphoe and this has to be over the app I want to use.  I then have to double click on the icon for it to open.  I cannot scroll across or down.  I can access the apps but because it will not scroll I cannot access all of the screen. Can nayone help please???

    It sounds like VoiceOver is partially on.  First try triple pushing the Home button.  This may turn VoiceOver off.  If that doesn't work going to Settings/General/Accessibility and make sure VoiceOver is Off.  Note you may have to use 3 fingers on the screen to scroll.

  • My favorites sidebar will not scroll, nor will folders open or close

    My bookmarks sidebar (on the left side of the screen) will not respond to scrolling or selecting. It stopped working when I installed Firefox 7. Went back to Firefox 6 and it still will not scroll. Nothing happens when I click the arrows or move the slider.

    Try:
    *http://kb.mozillazine.org/Corrupt_localstore.rdf
    Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
    *Don't make any changes on the Safe mode start window.
    *https://support.mozilla.com/kb/Safe+Mode

  • Some web pages will not scroll after update7

    Recently was FORCED to update my Ipad if I wanted to use podcasts. Now, some webpages will not scroll down and lockup. (safari)
    Never had this problem before update.  So I purchased another browser, (atomic) and it does the same thing.
    (and I dreaded update due to bugs!)

    To be specific, a news website AL.com
    I can scroll the main site, but if I open a news story, it opens and locks. Yes, I have rebooted, hard reset.

  • Itunes 11.0.1 tv shows will not scroll

    When I am syncing my ipad in the latest version of Itunes 11.0.1, the tv shows screen will not scroll properly using my magic mouse.

    I had this problem recently with the same symptoms as you. It also appeared to stream the podcast over the internet when I double-clicked it even though it didn't seem to be downloading. I eventually noticed that when I go to Preferences, there is no folder designated as the iTunes media library. This was weird because I don't know why that would have disappeared. Anyway, I pointed it at my media folder and everything started working again. I hope that works for you.

  • My Safari will not allow me to open my Google calendar with Google Apps. I have to open my email with the older version of Google Apps. This happened after I installed 5.1.4. I tried to use the fix of changing to 64 bit by unchecking the 32 bit box no go

    My Safari will not allow me to open my Google calendar with Google Apps. I have to open my email with the older version of Google Apps. This happened after I installed 5.1.4. I tried to use the fix of changing to 64 bit by unchecking the 32 bit box but that didnt help.

    I assume that there are legal restrictions on the way in which iTunes can get artwork automatically from any source apart from the iTunes Store (which is what the right-click > Get Album Artwork function uses).  For example, even though the Gracenote service that iTunes uses to match CDs and retrieve metadata (artist, album, track titles, etc.) also has artwork functions, iTunes does not make use of these.
    For manual addition of artwork, there are three cases where the image you select may not be correctly embedded in your media files:
    your media are in a format that doesn't accommodate embedded artwork - typically WAV files.  To embed artwork you'll need to convert to another format - Apple Lossless or AIFF if you want to preserve lossless quality, AAC or MP3 otherwise.
    your media files are read only - to fix this, use Windows Explorer to find the folder that contains your files, right-click and select Properties.  On the General tab there's a check box labeled "Read-only" - if this is checked, or is grey (sometimes blue), click the box so that the flag is unchecked and the box is white.  Click OK, and then OK again when the "Apply changes to this folder, subfolders and files" option selected.  Now try adding the artwork again.
    Windows permissions issues are preventing iTunes from updating your media files (there's some anecdotal evidence of a change in this behavior in iTunes 12).  See turingtest2's notes on Repair security permissions for iTunes for Windows for advice on fixing this, then try adding the artwork again.

  • Pages created with DWT will not scroll

    I recently acquired a contract to update a site built in CS2 with tables to something that's HTML 4.01 compliant. I'm using CS5 and have updated the DWT's design, but now my pages will not scroll using the new template. I've tried using the overflow tag in several ways and locations within the DWT and style sheet itself, but to no avail. I have also created new pages from this template and they won't scroll either. I'm clearly missing something, does anyone have any ideas as to what that is? Does anyone need snippets of code?
    Thanks, Kevin

    elvikingoproductions wrote:
    I recently acquired a contract to update a site built in CS2 with tables to something that's HTML 4.01 compliant. I'm using CS5 and have updated the DWT's design, but now my pages will not scroll using the new template. I've tried using the overflow tag in several ways and locations within the DWT and style sheet itself, but to no avail. I have also created new pages from this template and they won't scroll either. I'm clearly missing something, does anyone have any ideas as to what that is? Does anyone need snippets of code?
    Thanks, Kevin
    Why are tables not HTML 4.01 compliant?
    Regardless, you have to post a link to the page in question or provide the code (both HTML & CSS) for examination.  The typical link you will be pointed to is the validator, so you may want to clean up as much as you can before you provide the link.
    http://validator.w3.org/

  • Window will not scroll down in Design mode in DW CC 2014

    On a Wacom Companion running DW 2014.1.1, build 6981 Windows 8.0, opening a page, it will not scroll down in Design unless I click Split, then it will scroll some more and stop. Have to click modes back and forth to get to bottom of the screen. No issue viewing the page in a browser. Have 8 Tabs (pages) open, and other programs. Sys shows CPU/MEM at 38/84. Win 8.1 is installed, just need to reboot to activate upgrade.

    See this article for information on how to disable VoiceOver.
    http://support.apple.com/kb/ht3577
    B-rock

  • TS2662 trackpad and mouse will not scroll

    On 27" iMac using OS 10.7.4, trackpad and mouse will not scroll or swipe, can point with both, click only with mouse, scroll only with keys on keyboard.  What have I done now??? They are all paired with good batteries. Have checked in settings and they are enabled to scroll.

    In Lion the scrolling is natural i.e. reversed to the way that computers typically scroll. Think of the scroll as grabbing the page an moving it either up or down vs moving the scroll bar down up or down. Also, the scroll bars are "hidden" by default and only show up when you are scrolling.
    Are you using and Apple mouse? If you go to the system preferences and then to the "mouse" section there are options to change the natural scrolling. And if you go to System Preferences and then to "general" you can set it to show or hide the scroll bars.
    If this is not what the issue is let me know and let me know what mouse you are using because there is something else that it could be.

  • My touchpad will not scroll with the current version of foxfire.

    The screen in foxfire will not scroll with the sliding of my finger on right side of the touchpad on my lenovo thinkpad or the navigation button. It does work with all other programs including windows explorer and google chrome.

    OK, this is the original poster again. The trackpad scrolling problem has been sporadic. Now I have realized that I have this problem (in Firefox 7.0 and 7.01) WHEN THERE IS A PDF DOCUMENT OPEN IN ONE OF THE TABS. When there is a .pdf open, trackpad scrolling works fine in *that* tab but not in any of the other Firefox tabs that are open. When I close or move away from the .pdf file, then the scrolling function returns in the other tabs. Is there something about the Acrobat plug-in (ver. 9.4.5) that isn't working correctly in Firefox 7.x?

Maybe you are looking for

  • Return of Delivered Excisable items

    Hi All, user has made delivery for excisable item. Then created Outgoing excise invoice followed by AR Invoice. Due to some reasons the material was returned by customer for which if i try to enter AR Credit memo based on the AR invoice it get follwi

  • 8.1.7 connectivity using database link

    I can't get my database link to work. It fails with ORA-12154: TNS:count not resolve service name I have set up an entry in tnsnames that allows me to successfully tnsping the target database and I can connect via SQL*Plus using user/password@service

  • Macbook air mid 2012 slow usb 3.0 port

    Hi there I got serious problems with my MBA mid 2012, i'm a professional photographer and i use my mac to choose and send photo live from the events , i had a 2010 MBA and changed only for the USB port to make my workflow faster but since the first d

  • Checkboxes - invalid use of CStr?

    What is wrong with this for a radio group? My field "vatregistered" is an INT field in a SQL database and I'm using ASP/VBScript. <input <%If (CStr((rsDetails.Fields.Item("vatregistered").Value)) = CStr("1")) Then Response.Write("checked=""checked"""

  • Why is iMovie not opening my project ever since I shared it to iTunes

    why is iMovie not opening my project ever since I shared it to iTunes