TS3408 hello ! ... i did a disk repair a few weeks ago, followed by attempting to download a newer version of safari ... all worked ok for a few days, now i can't connect to the internet - i checked my configurations & all are green lighted, but can't con

having problems connecting to the internet after d-loading a newer version of safari ... please help !

Tiger, which you show as using, cannot use a version of Safari beyond 4.1.3.
What version did you attempt to install?

Similar Messages

I have full bars but i can't connect to the internet. I've done all the usuall thing like reset the ipad reset my internet security but everytime it says "safari cannot open the page because it is not connected to the internet" Any ideas?y

I have full bars but i can't connect to the internet. I've done all the usuall thing like reset the ipad reset my internet security but everytime it says "safari cannot open the page because it is not connected to the internet" Any ideas?

As with previous posts this is usually a DHCP issue and occurs frequently especially with routers connected to Cable Modems or those Micro-Cell towers.
Unplug all Routers, AirPorts (or other off brand Wi-Fi broadcast units) and any other Wireless broadcast unit that might provide you with a WDS (often other AirPorts feeding off the signal of the AirPort closest to Cable/DSL Modem) and best to totally power down the Unit affected; lastly either hold a reset button on Cable/DSL modem for 30-45 seconds or actually power it down if an option (not suppose to power down Cable Modems that have Telephony for some odd never completely explained to me reason).
Let Cable/DSL Modem re-boot till 'all green lights'. Then power up each device involved in order from closest to farthest waiting each time for completion of initiation. Micro-cell towers can take 10 minutes to completely re-boot and you must wait for across the board green lights in my experience. Even WDS can add a few minutes till all green on mother AirPort unit.
Only NOW may you re-start the offending device and see if it will connect. Works about 99% of the time!

TS1398 I installed the iOS 6 update for my ipad 3, now it will not connect to the internet. Has this happened to anyone else?

Actually I cannot access my home wifi from my laptop or cell anymore either.
I reset the modem and router about 10 times and called my ISP who said there's no problem on their end.
I've tried everything I can think of. Any advice?

Make Sure iOS is updated to the latest version
Reboot the device by pressing and holding down the home and sleep/wake buttons (power) at the same time until the apple logo appears on the screen, then let go.
If that doesn't work then reset the device by going to settings/general/reset/reset all settings
If that doesn't work, then update iTunes on computer, backup device to iTunes, then restore the device.
iTunes: Backing up and Restoring iOS software
http://support.apple.com/kb/HT1414?viewlocale=en_US

Hello, I've upgraded my Ipad2 to iOS7. I'm facing two major problems. First, I can't connect to the internet(which seems like a common problem). Second, the Autocad WS app doesn't work. It keeps asking for a username/passcode combination. please help guys

Hello, I've upgraded my Ipad2 to iOS7. I'm facing two major problems. First, I can't connect to the internet(which seems like a common problem), no Wifi connectivity as well. Second, the Autocad WS app doesn't work. It keeps asking for a username/passcode combination. Please help me guys. I will be genuinely grateful.
Cheers

Does my problem has anything to do with SSL for mail settings? Cause when I tried re-adding it says something that I should try without SSL, and I did what you said and it gives me this "The IMAP server pop.mail.yahoo.com is not responding. Check your network connection and that you entered the correct information in the incoming mail server field". Ahh.. this is so annoying, Apple what are you doing to me?! Or is Yahoo doing this to me?!
Thank you for your time. Sorry it doesn`t work.

Was always working and today I get a message that it can not connect to the internet. Internet Exployer works fine. So, I tried uninstalling the program and reinstalled. Still did not work. check out the proxy and firewall no problems there.

I get a message can not connect to the internet when trying to open Mozzila Firefox. It was working fine until my internet service went down. Once back up it was not working. I have tried installing and uninstalling the browser. I have looked at the firewall and proxy on my computer. Still not working Internet Exployer works fine. Deleted all cookies also.

Did you check your security software (firewall)?
A possible cause is security software (firewall) that blocks or restricts Firefox without informing you about that, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox.
See [[Server not found]] and [[Firewalls]] and http://kb.mozillazine.org/Firewalls

Switched from DSL to Cable, Can't connect to the internet

After switching to cable modem (Motorola SB5120 SURFboard) from DSL, I can't connect to the internet using my airport express. Everything is green - modem and airport, and the signal on my computer looks like I have full access, but there is a scrolling message... looking for PPPoe host. I have unplugged everything and restarted per the instructions on this site, but get the same result every time. My computer connects just fine using direct connection to the modem. I saw a download for a firm ware update for the express, but don't know how to apply that, either. Any help out there?
Thanks!

Hello mom2gr82. Welcome to the Apple Discussions!
Let's double-check your AirPort Express Base Station's (AX) settings...
AirPort Express Base Station Setup (AX) w/High-Speed Cable Modem
Perform a "factory default" reset of the AX
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
Modem/Router Power ReCycling
o Power-off the Cable modem, AX, & computer(s); Wait at least 30 minutes.
o Power-on the Cable modem; Wait at least 15 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
Setup the AX
Connect to the AX's wireless network, and then, using the AirPort Admin Utility, try these settings:
AirPort tab
o Base Station Name: <whatever you wish or use the default>
o AirPort Network Name: <whatever you wish or use the default>
o Create a closed network (unchecked)
o Wireless Security: Not enabled
o Channel: Automatic
o Mode: 802.11b/g Compatible
Internet tab
o Connect Using: Ethernet
o Configure: Using DHCP
o WAN Ethernet Port: Automatic
Network tab
o Distribute IP addresses (checked)
o Share a single IP address (using DHCP & NAT) (enabled)
Once you verified that you can get Internet access for all of your computers, you should secure your wireless network. To do so, I suggest that you make these changes:
Change Wireless Security
o Wireless Security: WPA Personal or WPA2 Personal
o Encryption Type: WPA and WPA2
Base Station Options - WAN Ethernet Port
o Enable Ethernet Port (checked)
o Enable SNMP Access (unchecked)
o Enable Remote Configuration (unchecked)
o Enable Remote Printer Access (unchecked)

Can't connect to the internet

Ok. so i did a search and didn't come across any other problems like the one I'm having.
Let me start off by stating that my laptop is an ibook g4 bought feb, '06 (yes the apple care just ran out).
I'm having a problem connecting to the internet on my ibook, running through a d-link wireless router. I'm using my imac to connect to the internet currently (which works fine by the way). It also is connected through the wireless router.
My ibook has a strange ailment. I open up Safari and all I get is a blank screen, the page is trying to load but the status bar is going no where and does the same in Firefox. So first, I opened Network diagnostics, but the computer freezes and I have to do a hard shutdown. (holding the power button). Next, I tried Disk utility. Verified Permissions, Repaired Permissions, everything is fine. I tried to Verify Disk, and again the computer freezes, will not let me force quit and I am forced to do another hard shutdown. I do the thing where you hold down some key while you're starting up to get into the disk utility so I can repair the disk. This returns clean as well. I downloaded techtool off of my Applecare disk. Did the tests, everything passes. So what's the deal?? I've tried to reset the pram. I even did the Apple Hardware test, everything passed.
I thought it could be my Airport card? It recognizes that there is an internet connection in the top right corner, I even have great signal strength (mostly because I've tried this sitting right next to the router). But still, I can't connect to the internet. Any one have any ideas? I don't know what else to try! Please help!

so i can't believe i didn't try to connect it directly to the router with the ethernet cord. This actually worked. But it still didn't solve my wireless problem. I'm not willing to let my laptop become a desktop. I'm already wired to a plug b/c the battery is slowly dying and has a life of about 5 minutes. I'm not willing to give up my wireless internet too.
I guess now it's got to be the airport card? how do I confirm this? and if it is how much would a new one cost and can I install it myself??

Can connect to my house network, but can't connect to the Internet (other computers can)

Hello,
I'm experiencing a strange problem. Since I started my Mac Pro (cold start) some hours ago, I've lost the hability to connect to the Internet (Safari and Mail say I'm not connected). However, I can connect to 192.168.2.1 (my router) and see its webpage (it says it's connected to the Internet). If I use another computer on the same network, it can also connect to the Internet.
Weirder, if I go back to my Mac Pro with "no internet" and launch Parallels Desktop, then I can use WinXP to browse the Internet; I'm writing this post on my WinXP virtual machine.
This leads me to think there's a problem with how my Mac OS handles the networking. I have checked the Console, but the only related string I found is this:
16.04.13 22:03:25
kernel
SIOCPROTOATTACH_IN6: en2 error=17
As expected, Google doesn't reveal anything about that (and I'm connected with the first ethernet port). I've tried to restart my Mac, but the problem persists (exact same symptoms).
Could it be a DNS cache issue?
I don't see, other than a DNS problem, why I can't connect to the Internet with my Mac OS while I can on my virtual machines. If it was a driver problem, I wouldn't be able to connect to my router. If it's a DNS issue, where are the DNS caches located in order to clear them (I'd trash the folder)?
I could also reinstall the OS (waste of time, btw), but I'd really like to understand the problem, not just clear it and forget about it.
Or better than guesses, anyone already experienced this?
Any help welcome.

If it's a DNS issue, where are the DNS caches located in order to clear them (I'd trash the folder)
No DNS caches, it looks up the alphabetic and then uses the numberic from then on.
http://17.149.160.49
is Apple, Inc main US web site. It that works, and the alphabetic does not, you have a DNS probelm.

I just downloaded the latest OS upgrade and since I can not connect to the internet using my cellular data plan.

I just downloaded the latest iOS.7 upgrade on my ipad2, and since I can not connect to the internet using my cellular data plan. I have checked my data plan and it's both current and over 2GB remaining. However the indicator shows no service, thus would be the best steps to recover. Thanks much for any support that can be provided.

Hello Kmart2@3
Check out the troubleshooting article below to get cellular to start working again.
iPad (Wi-Fi + Cellular Models): Troubleshooting a cellular data connection
http://support.apple.com/kb/TS4249
Regards,
-Norm G.

New MBPro...airport connection established but can not connect to the internet...help! suggestions?

Hi all, trying to set up my MBPro...seems to be connecting to my AirPort Base Station w/out any troubles...but when I try to get online I'm getting a "can't connect to the Internet" message. I checked my network settings, restarted multiple times, etc. No luck. Seems to be a problem with the IP address (I think)...but not sure how to resolve it. I have an iMac and iPhone in the house that are able to connect and get online w/out issues. Any thoughts? TY!!

Are you asking the make/model of the computer or the AX base station?
Neither, I was interested in the make/model of the cable modem.
Our ethernet connection was fried in an electrical storm so we had to go wireless.
Electrical storms are never a good thing when it comes to electronics. What was/is your current network configuration? Is it something like the following?
Cable modem > (Ethernet cable) > AX > (wireless) > wireless devices
Is there another router, other than the AX, in the configuration? ... or an Ethernet switch? I'm just trying to understand your network to best advise you on how to configure the AX.

Can't connect to the internet though my iMac thinks everything is fine

I got my iMac connected to a router which is connected to a DSL-modem. I had this up and running for a year until I needed the router for something else and then put it back in place.
Now I can't connect to the internet. I got a green dot for my network settings, I got a plausible IP, the router's IP is filled in correctly. When I run the assistant it tells me that there are no problems connecting to the ethernet.
I tried switching routers, I restarted both the router and the modem (and the iMac of course), I tried entering the IP-adress manually... nothing works.
And by the way; my old b/w G3 works just fine at the same cable. Both computers got the same settings in the network panel, but obviously something does differ, but what?
And by the second way, I had my iMac at the workshop which charged me for checking it since it doesn't have any hardware problem.
HELP!
Thanks in advance! Daniel

Naa, I really don't know any longer what to do. Now I'm sitting with my old laptop at the same cable after replacing DSL-splitter, DSL-modem, the router including power supplies, I even cut the contacts and fixed new ethernet-plugs. Works fine with this PC, works fine with the G3, and it just won't work with the iMac.
Last chance: I'm gonna try with WLAN, probably there's something wrong with the ethernet adapter even though this repair dude couldn't find anything.
*E D I T*
Japp, airport is working just fine. This means that there's something wrong with my iMac, right? I'm gonna take it to my job on monday and try to connect to the LAN there, then we're gonna see.

After update I can't connect to the internet in no way, shape or form

I rarely update because: 1) something always breaks when you update (like now) and 2) I don't like to deal with new crap like GNOME 3. Anyway:
I bought a new router (TL-WR1043N) and configured it with an old Ubuntu because connecting to 192.168.1.1 didn't work on any of my Arch Linux installations. Now... here's where it all starts... I can't use the 'n' wireless on my laptop since I have to install something to use WPA, and to install that I need to update, but I don't want to deal with GNOME 3 and Firefox >3. But I gave up eventually gave up and connected my laptop to the router by Ethernet cable. Setting that up was very easy: 'ifconfig eth0 up; dhcpcd'. Voila! I updated my whole system and restarted. To see how badly I damaged my system I opened Nautilus (I use Openbox with some GNOME programs): shock and dismay, the fonts are visible from the moon. I guess I'll have to quit using GNOME programs completely now but I expected that. I used to use KDE back in the day and when KDE4 came forth from that unholy pit, I immediately abandoned it for GNOME. This time we had more time to prepare, everybody knew what GNOME 3 was going to be. I started using Openbox quite a long time ago.
Anyway: Now to fix my wireless right? WRONG! I can't connect to the internet on cable to get the packages for wireless. I installed Windows 7 64 on the same laptop and it connects to the cable. Ubuntu 9.10 Live also connects, but due to the changes of rc.conf and network stuff I can't connect at all with Arch Linux.
So I decided to abandon it completely and reinstall from scratch. But the Live CD also doesn't work. With all the ways I've tried it all comes down to this:
dhcpcd always times out waiting for a carrier and 'ip addr' shows 'eth0: <NO-CARRIER, ....' if the interface is up. I'm not sure what information I should give you, but I can't paste any here since I can't connect to the damn internet on that laptop.
About the router: the cable is plugged on port 1 and the LED for it flashes if I reboot the computer. In Windows it stops flashing while it connects and flashes again when connected. I removed 'network' from DAEMONS and it flashes till I start it with '/etc/rc.d/network start'. This hangs for a while and returns '[DONE]' even though it doesn't work and the LED never flashes again on the router.
In rc.conf I have exactly what the example says for DHCP. In any case, it doesn't work with the Live CD either.
EDIT 1: From lscpi: painstakingly typed:
06:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
07:00.0 Ethernet controller: Realtek Semiconducctor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
EDIT 2: Just to be clear: I can use the wireless on the laptop on the Live CD, but I want to use the cable because of the greater speed (94Mbit/s on cable 60 something on wireless n, 20 something on g) and because I rarely move the laptop.
EDIT 3: lspci -v shows "Kernel driver in use: r8169 / Kernel modules: r8169", so the driver is loaded.
EDIT 4: So if I boot from the CD. ip addr shows:
eth: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:1d:92:...etc... brd ff:ff:ff:ff:ff:ff
And the LED flashes. When I type: "ifconfig eth0 up" it stops, never to light up again and ip addr shows: "eth: <nO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
Last edited by imtired (2011-09-08 12:36:51)

When you're in Arch, use output redirection
lspci >lspci.out
then boot into Ubuntu or something where you can access the files and the BBS, Of course, don't forget to use a new file for each command output.
The new network config in rc.conf is not that complicated (wired anyway; never used wireless). OTOH I've had issues on two machines where I have to restart the network daemon (rc.d restart network) or rerun netcfg (netcfg eth0) after boot to get connectivity. And I still haven't come to grips with the ip command.

I have a MacBook Pro. My mac can detect wifi. But will not connect. I did get connected vis TCP/IP settings but I can't connect to any wifi anywhere. Network diagnostic has a green light for wi-fi and wi-fi settings. Red light for the rest.

I have a MacBook Pro. My mac can detect wifi. But will not connect anywhere. I did get connected via TCP/IP settings but I can't connect to any wifi anywhere. Network diagnostic has a green light for wi-fi and wi-fi settings. Red light for the rest. (Network settings, ISP, Internet and server.)

Hello NotAppleSavy,
Thanks for the question. After reviewing your post, it sounds like the computer wont connect to networks. I see you have used network diagnostic. I would recommend that you read this article, there are a lot of other things you can do in this article that may be able to help you resolve or isolate the issue.
Wi-Fi: How to troubleshoot Wi-Fi connectivity
Thanks for using Apple Support Communities.
Have a nice day,
Mario

Can't connect to the internet in my home yet other devices can. I tried it in other Wifi places and it connects without a problem. My home Wifi is with Att uverse

Can't connect to the internet in my home yet other devices can. I tried it in other wifi places and it connects without a problem. My home wifi is with ATT Uverse. I cheched the IP address on my laptop and its different than on my Ipod although it on the same network.

Move off WEP to WPA or, preferably, to WPA2 (as recommended by Apple). WEP has been deprecated by the WiFi Alliance since 2004 as insecure (it can be cracked in seconds by any hacker).
Note that each device on a network has a unique IP address but if your address starts with 169 then you did not get a valid IP address assigned to you by your router. If restarting the router did not cure the problem then you should check for a firmware update for your router.

Can not connect to the internet. This is a new problem since I have been using firefox for years.

I can not connect to the internet. I called mediacom due to the problem and they connected me to internet explorer. They indicated I should contact you for help in connecting to the internet. It appears firefox has made some kind of change since last night since I was using firefox for my internet connection last night. Something has changed. Your help will be appreciated.

http://en.wikipedia.org/wiki/Keyhole_Markup_Language
The only way that file opens thru IE8 for me ''(but not actually in IE8)'' is by using the Zip Utility (then IE closes) that is in WinXP and then opening the two image files in the Windows Fax and Picture Viewer.
I think Firefox is trying to display that file because the MIME-type is for '''''text/plain''''' instead of the appropriate MIME-type of '''application/vnd.google-earth.kml+xml''' or '''application/vnd.google-earth.kmz'''
That is something that needs to be configured in the server that is hosting that file type. Sorry, I don't know how that can be fixed. The one support person here that might know lives in Europe ''(I believe)'', so you might need to wait for an answer.

TS3408 hello ! ... i did a disk repair a few weeks ago, followed by attempting to download a newer version of safari ... all worked ok for a few days, now i can't connect to the internet - i checked my configurations & all are green lighted, but can't con

Similar Messages

Maybe you are looking for