TS3499 macbook recognises but will not charge new battery

I was advised to buy a new charger last week and have just been advised by an apple employee to buy a new battery for my MacBook 2009 and i am having the same issue as my old battery.
The Mac reconognises the battery but will not charge or run off the battery.
Just spent £150 in total on new charger and battery but still having the same problem as before.
I have downloaded the firmware update but my Mac is already running the latest software.
Regards
Jack

Have you reset the SMC and pram?
MacBook and MacBook Pro 
Laptops with a battery you can remove 
Shut down the computer.
Disconnect the MagSafe power adapter from the computer, if it's connected.
Remove the battery.
Press and hold the power button for 5 seconds.
Release the power button.
Reconnect the battery and MagSafe power adapter.
Press the power button to turn on the computer.
Newer Mac portables with a battery you don't remove
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.  
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
Resetting NVRAM / PRAM
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

Similar Messages

  • MacBook Pro turns on but will not load. Battery will power up and charge. The PRAM second start up seems to work, but the Apple timer continues add-infinitum. There is also a disc in the laptop so I can't load re-load software OS 10.6.1. How do I resolv

    MacBook Pro turns on but will not load. Battery will power up and charge. The PRAM second start up seems to work, but the Apple timer continues add-infinitum. There is also a disc in the laptop so I can't load re-load software OS 10.6.1. How do I resolve this problem?

    Try booting in Safe Mode by holding your Shift key down when booting. Also, try holding the eject key down when booting to eject the DVD. If you plug a mouse in and hold the clicker down when booting, that should eject the DVD.   
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

  • Battery charges when asleep but will NOT charge while awake

    Hello -
    By battery will charge when off/asleep but will not charge while awake. It just slowly drains to nothing and dies even though adapter is plugged in. magsafe adapter light is green when open/on and orange when off/asleep and lights on battery indicate charging while in the latter state. still using stock battery that came with computer when I got it a few years ago, so it's not new by any means, but when fully charged lasts as long as it used to. I would think maybe charger is issue, but it DOES charge, just not while awake. not sure why computer wouldn't still work correctly while plugged in if in battery indicator it says power source is "power adapter," but its not. I have tried resetting PMU and calibrating battery. the combo of the two seemed to work when having issue a few months ago, but it just started doing it again. frustrating because once it dies I have to wait several hours until its fully charged again, so it cramps the workflow... any ideas? battery info from profiler below.
    Cheers,
    Ian
    Battery Information:
    Model Information:
    Serial Number: DP-ASMB013-3556-2063
    Manufacturer: DP
    Device name: ASMB013
    Pack Lot Code: 0001
    PCB Lot Code: 0000
    Firmware Version: 0102
    Hardware Revision: 0300
    Cell Revision: 0100
    Charge Information:
    Charge remaining (mAh): 81
    Fully charged: No
    Charging: No
    Full charge capacity (mAh): 4571
    Health Information:
    Cycle count: 827
    Condition: Good
    Battery Installed: Yes
    Amperage (mA): -1134
    Voltage (mV): 10921
    System Power Settings:
    AC Power:
    System Sleep Timer (Minutes): 60
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 20
    Automatic Restart On Power Loss: No
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Wake On LAN: Yes
    Display Sleep Uses Dim: Yes
    Battery Power:
    System Sleep Timer (Minutes): 5
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 1
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Display Sleep Uses Dim: Yes
    Reduce Brightness: Yes
    Hardware Configuration:
    UPS Installed: No
    AC Charger Information:
    Connected: Yes
    Charging: No

    Scott - Your answer ultimately led me to the answer, albeit months later, after much internal deliberation and some trial and error... thanks!
    Ruled out battery (as crazy as that sounds - it's had a bajillion cycles) as it didn't make sense that battery would charge but wouldn't work while awake. I have a friend whose battery is completely shot and his still works as long as magsafe is plugged in, and mine wouldn't even do that. tried another adapter and that worked. then tried mine in a different plug. so in the end, turns out I had a bum powerstrip... mag safe / battery recharge works properly when just plugged in somewhere different.
    So no need to buy a new charger or battery (yet!)
    thanks to all,
    Ian

  • My IPod nano 6 connects to my library but will not receive new music and playlists

    My ipod 6th generation will not receive new songs and playlists from my library on my PC. My ipod shows up in the itunes library when I connect it. It syncs when it is plugged in to computer but the sync is very short. I changed to a new computer back in September 2013. My old one crashed.  I have synced my ipad 2 and my iPhone 4S to itunes library on the new computer.  All these devices show up in the "manage my devices" list except my ipod 6th generation. There is no "add device" to this itunes account, only an option to deauthorize the computer, the iPhone or the ipad.
    The ipod downloaded songs that I added to my computer library on my new computer, but will not add new purchased songs nor library playlists.
    My computer is shared with my husband. His user account on the same computer shows up in my "manage devices" section of my itunes account. He doesn't use it. I thought I had to add my itunes on his part of the computer because his is the "main user". 
    I'm not sure what to do.  Should I take my computer, iPhone, ipad and nano to an appointment at the Genius Bar at the Apple Store?  Any help is appreciated. Thank you.

    I kept working at this after posting. On the sync page for the ipod on itunes library I chose to remove the iPods association with my old computer. It erased all the old content from the old computer and then put all my checked songs from the new computer on my iPod nano.

  • My Macbook Pro suddenly will not charge.  I tried using 2 different cables  and it still will not charge.  What should I do??

    My Macbook Pro suddenly will not charge.  I tried using 2 different cables  and it still will not charge.  What should I do??

    Look at the power adapter connection on the MBP and make certain that it is clean and not discolored.
    Trya SMC reset:
    http://support.apple.com/kb/ht3964
    Ciao.

  • My brand new MacBook Pro retina display not charging the battery any more after 3 weeks...no green or red Led. Any one now about this problem? Thanks

    My brand new MacBook Pro retina display not charging the battery any more after 3 weeks...no green or red Led. Any one now about this problem? Thanks

    Either the power brick is damaged, or the charging circuit is on the blink, or both. Either way, a trip to the Apple Store or the Apple Authorized Service Provider is in order, as this ain't no bargain basement toy.
    In the meantime, can attempt an SMC Reset to see if it helps.

  • TS1367 My charger connects with my macbook with a very faint green light (not the normal orange light) and can maintain the computer turned on but does not charge the battery.

    My charger connects with my computer with a very faint green light (not the normal orange light) and can maintain the computer turned on but does not charge the battery. The power source to keep it on is the power adapter and that it's "Not charging" on the battery settings. And my charger seems to charge other computers fine.
    The part of my mac where the adapter (L-shaped, magnetic) attaches is a bit damaged - a small piece of the white case/body around the part where the adapter attaches is broken off, but that's just an outer damage.
    I don't know what's wrong with my computer, and if anyone has had a similar experience or knows what's going on, it'd be tremendously helpful!
    Thank you!!

    Hi Christopher,
    Doubtful an upgrade would fix a hardware issue. If you are thinking of upgarding to Lion, best to do all necessary maintenance first.
    Try Resetting the System Management Controller (SMC)
    If that doesn't help try here >  Apple Portables: Troubleshooting MagSafe adapters

  • 4s will not charge until battery dead. Tried reset and powering off.

    4s will not charge until battery dead. Tried reset and powering off.

    Inspect the charging port area for dirt/debris/fluff build-up that may be preventing a good connection and use a wooden toothpick, soft clean toothbrush, or a can of compressed air to clean it. Also look for bent or broken pins. Try another cable and/or charger block (be sure to always use a genuine Apple certified brand) in a known good outlet. If you're using a USB port, try another port. If you're using a hub, try a direct connection. If you're using a USB port in the front of a desktop computer, try one in the back. If all these fail, make an appointment at your nearest Genius Bar to have the device evaluated.

  • TA44551 my i pod classic will play works great! in a dock but will not charge ( after new battery ) HELP !!!

    I have an older Ipod classic it plays on everything i have . Recently replaced the battery because it would not take charg .After new battery it plays through several defferent devices but it will not CHARG !!!    HELP!!!!

    Not Charge
    - See:      
    iPod touch: Hardware troubleshooting
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar                          
    Also:
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer          
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • Macbook pro 5,3 will not charge the battery

    the 85w charger will not charge my macbook battery, the indicator turns orange indicating that its charging, but the battery charge level does not increase.  either its the charger or its the battery not accepting a chare.
    is there any way to distinguished between what one it is other than purchasing a new charger?

    See Step #1 for power/battery issues. Do a SMC Reset.
    Step by Step to fix your Mac

  • My ipod connects to the computer but will not charge, can you help?

    My ipod will not charge. I have tried charging via the mains and via the computer. The computer recognises it but it still won't charge. Any ideas as to what the problem might be?

    See the not-charging topic of:
    iPod touch: Hardware troubleshooting
    Another charging source?
    Look at the dock connector on the iPod. Look for abnormalities like bent or corroded contacts, foreign material and cracked or broken plastic.
    Time for an appointment at the Genius Bar of an Apple store.

  • My iPhone 4 will charge on a wall socket but WILL NOT charge on computer or even connect to the computer and show up???

    My iPhone 4 will not connect to my MacBookPro. It will not charge on my MacBookPro, but it will charge on a wall socket and it will play music in a 3rd party speaker system??
    This is extremely frustrating not only can I not back up my iPhone but I also can not update its OS etc.

    Have you tried other USB Sockets on the MBP?
    Have you tried other devices in these USB sockets?, do these work?
    Sounds like a fault on the Macbook

  • 2nd Gen Ipod will sync with itunes but will not download new song

    My Ipod will sync with itunes but will not download newly purchased songs.  It is Ipod nano 2nd gen.

    If you want to use automatic syncing, you may need to set up or update the iPod's Music sync settings in iTunes.  If the new songs are not included in what gets synced to the iPod, they will not sync.
    If the sidebar (along left side of window) is hidden, from the menu bar, under View, select Show Sidebar.  The iPod appears in the sidebar, under DEVICES.  Select it there, to show its Summary screen to the right.  Toward the top, there is a bar of buttons, starting with Summary.  Click on Music next to Summary.  This Music screen is where you tell iTunes how to sync songs to the iPod.
    Check the box for Sync Music, if not already checked. This is the "switch" to enable automatic syncing for songs.
    NOTE:  If Sync Music is not already checked, that means the iPod is currently set to Manually manage music.  Setting up automatic syncing will replace the iPod existing content.  If you want to add the new songs manually to the iPod (instead of using automatic syncing), please post back.
    If your iTunes library fits on the iPod, you can choose the option to sync Entire music library.  Otherwise, choose the option to sync Selected playlists, artists, albums, and genres.  Below that, select (checkmark) what you want to sync to the iPod from the lists.
    One convenient way to set this up is to first create one or more playlists in your iTunes library, with ALL of the songs you want on the iPod.  Or you can use existing playlists.  Back on the iPod's Music screen in iTunes, select those playlists under Playlists.
    When you click Apply, iTunes syncs the songs in your selection(s) to the iPod (replacing its existing content).  Going forward, to update the iPod, you can just update those playlists in your iTunes library (add/remove songs).  If you have new songs, add them to a playlist that is synced to the iPod.  The iPod does not need to be connected.  The next time you connect the iPod (or click Sync if already connected), iTunes automatically updates your iPod with the same changes.

  • IPod touch recognizes it is plugged in and has low battery but will not charge no matter what it is connected to! Suggestions????

    After a year of owning my iPod touch 4g it suddenly stopped charging on my computer and outlet addapter.  It still shows the two pronged plug icon that recognizes the iPod is connected to something but even as the battery level goes below twenty percent it will not charge. Still functions well and even connects to iTunes.

    If it is still under warrenty which you can find out from here or if you know it's under one year old bring it to the Apple Store.
    https://selfsolve.apple.com/agreementWarrantyDynamic.do

  • TS2771 Ipod connects to tv, but will not charge or sync

    My ipod was charging fine on my drive home. I connected it to my tv with the video cable and was watching netflix. Then I got a message that the battery was at less than 20%, even though the ipod had been connected to the wall charger the entire time I was watching.
    I've tried every charger, every cable, every dock, and every computer I own now, and it will not charge with any of them. Neither my desktop or laptop will recognize that it is connected. The ipod never shows that it is connected or charging. I tried pushing the power & home buttons to reset it and still have the same problem. The reset made no difference. And I'm low on power so there's not much else I can do before it completely runs out of charge.
    Any idea why it would give out on me so suddenly, or what I can do to fix it?
    Model# PC547LL
    iOS version 6.0.1

    - See:       
    iPod touch: Hardware troubleshooting
    - Try another cable
    - Try another charging source
    - Inspect the dock connector for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genus Bar of an Apple store.
    Apple Retail Store - Genius Bar

Maybe you are looking for

  • G550 - short cuts no longer working

    Forgive if I'm posting this in the wrong location. Please advise if I should post this elsewhere. I have a G550 and it's been great. But today all my shortcuts to my applications stopped working. 2 issues/examples: 1) If I try to launch a web browser

  • Upgrade mac os 10.5.6 without disk

    How can I upgrade mac os 10.5.8 to 10.6 over the internet.

  • CHOPPY IMPORT FROM ILLUSTRATOR

    Hi everyone. I'm importing some files from illustrator and right now im using the original .ai project files not pictures or exports of it, but when i go to full resolution i'm getting all the text really choppy and even the circles (and image that f

  • Gamma levels on MacMini/Mountain Lion

    I have migrated my FCP 7 over to a MacMini, upgrading the OS to 10.8 in the process.  The first time, I just used my time machine to copy to the new computer, but all may Final Cut Material showed up with significantly altered gamma levels.  I had to

  • Captivate 7 - Shrinking Smart Shape Buttons

    Adobe Community, Currently we are starting to creating training modules in Captivate 7, we use a "wrapper" for the output which simply means this. The wrapper is simply designed to listen for specific Adobe standard 'actions' or 'calls', which I'm to