TS3824 FROZEN WHITE SCREEN DURING INTERNET SEARCH ON IPOD

WHILE SEARCHING INTERNET SCREEN WENT WHITE AND IS FROZEN.

- For the reset that T.Lange describes you have to hold longer.  Apple says:
Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Next try connecting to yur computer and try to restore via iTunes.
- If screen is still white, let the battery fully drain. After charging for an hour try the above again .

Similar Messages

  • TS3805 my ipod has a frozen white screen

    my ipod has a frozen white screen ipod touch 8GB model a1367

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • My ipod 4g has a frozen white screen and will not turn off, any advice?

    My daughter's ipod 4th gen (only 4 months old, bought direct from Apple) suddenly has a frozen white screen and will not turn off. We cannot reboot it by pushing and holding the two buttons, even when held up to one full minute. When we plug it into the computer, the computer does not recognise it nor does iTunes, so we can't even do a full system restore. Help! Any suggestions of how we can reset to factory settings without using iTunes please?

    - Let the battery fully drain. After charging for at least an hour try :
    iOS: Not responding or does not turn on
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • Older Version MacBook White Screen During Use

    My MacBook (early 2009) keeps getting a white screen during use for anywhere from 15-90 seconds. Is this normal? What can I do to fix it? Or is the computer just too old and I should get a new one?

    I have 24 inch iMac and I get either an almost black screen/white screen or sometimes a green and white vertical pinstriped screen. This happens suddenly with no warning & I have to hold the start button in to shut down. It then starts up fine with apparently no harm done. It is very annoying but I need to know why my Apple is doing this. Computer is around 2-3 years old and now running 10.6.8. I had to buy this as when I inherited the machine know one knew where the OS software was.
    Does anyone rate Genius bar - can they determine what the prob is? I took a G5 tower in as it wouldn't start but they were unable to help - local PC shop sorted it charging me £100 - realised later it needed a new battery (£7) so you can't rely on anyone out there I'm afraid!
    I will need a new iMac 27 inch anytime soon but am loath to give anyone currently selling machines the money!

  • Stuck on white screen during reboot after installing Snow Leopard

    I had no problem with installation, but am stuck on the white screen during automatic reboot. I manually ejected the disc hoping that would help. I am not sure how to get past this white screen of death. I tried to reset the PRAM but nothing I do will get me past the white screen.

    I am having this problem right now. It just goes to white screen during the installation right after rebooting. Just before rebooting it tells me to be 'ready' with the second disc, but then reboots and goes to white screen with apple logo and spinning gears....am I supposed to be putting the second disc in at this stage? Shouldn't it be prompting me to do something? Did either of you figure a way around this? Any help much appreciated.

  • When I click the icon Phone on my Iphone 5S, returns a white screen during a few seconds and then return the icons screen again

    when I click the icon Phone on my Iphone 5S, returns a white screen during a few seconds and then return the icons screen again. I can not access the Phone features like Favorites etc

    Can you connect your phone to iTunes on your computer?

  • IPod frozen white screen after cancelled wifi system update

    My iPod Touch 4g has a frozen white screen after cancelling wifi update to ios 5.1. My update bar was frozen middle way through when doing wifi update to ios 5.1. So i reset ipod and it displayed an apple logo which faded into a white screen. not jailbroken.

    I let battery drain, plugged into computer but when it booted up it booted to an apple logo with lines across the screen. It is frozen. iTunes did not recognise, it never showed up on iTunes. It is fading into a white screen.

  • My ipod touch has got a frozen white screen have tried all advice nothing comes on screen i have restored it but still nothing could it be the touch screen which was replaced around a month ago ?

    my ipod has a frozen white screen i have gone through all the holding buttons procedures and reset on laptop but still nothing,could it be the touch screen which was replaced around a month ago but has worked fine till now

    Couold be related tot he sscreen replacment
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem. I would take it back to where the screen was replaced.

  • Frozen white screen and vertical stripes on boot

    my early 2011 17" MBP  lcd has vertical stripes and gets frozen white screen on boot. Is there any fix to this?

    It sounds like it could be a display or a display connection fault.  An appointment at an Apple store genius bar should be made.  The evaluation will be for FREE.
    Ciao.

  • 9850 White Screen during OS upgrade

    After losing power during a security wipe (long story) i've tried several methods to either reload the OS to my BlackBerry 9850 or just wipe it to start from scratch. In each instance, the device can boot to 3/4 of the white bar and then will go to a completely blank screen. This will stay indefinitely until power loss.
    1) through my Mac BBDM: when the OS is not detected, I try to upgrade and as the device is initializing, it goes to the white screen and the BBDM eventually says the upgrade was a failure.
    2) through mac Terminal: I've tried a factory reset through Terminal using the "./bbdm resettofactory". It gives me a message of "RIM Software" or something to that effect but doesn't seem to reset the device at all.
    3) through VirtualBox running windows: I've tried connecting my device this way and though the device appears on the VirtualBox software (it says a RIM Blackberry device is connected via USB), neither BBSAK or AppLoader.exe will detect the device to let me wipe it or go through the AppLoader process.
    Any ideas out there? I figure there's got to be a way to force detection such that I might wipe the device to a factory state so that I might then reload the OS.
    Device info
    Your carrier: It was bought from US Cellular but I am using it with a SIM card in the UK.
    Model info and OS version (Go to Settings, then Options, then about): OS 7.1
    Apps and free space
    Did a battery pull fix your issue? No.
    When writing your question
    Good description of what is really wrong and how to reproduce if possible. Details of what you did before: Again, I was trying a security wipe after some software issues made me want to start from scratch and the device lost power before the wipe was completed.

    Hello,
    Given all you describe, I do not think it can be recovered via a MAC. You will need a PC. After you've arranged such access, I recommend the following.
    1) Make sure you have a current and complete backup of your BB...you can find complete instructions via the link in my auto-sig below. This is likely moot in your situation.
    2) Uninstall, from your PC, any BB OS packages
    3) Make sure you have the BB Desktop Software already installed
    http://us.blackberry.com/software/desktop.html
    4) Download and install, to your PC, the BB OS package you desire:
    http://us.blackberry.com/support/downloads/download_sites.jsp
    It is sorted first by carrier -- so if all you want are the OS levels your carrier supports, your search will be quick. However, some carriers are much slower than others to release updates. To truly seek out the most up-to-date OS package for your BB, you must dig through and find all carriers that support your specific model BB, and then compare the OS levels that they support.
    5) Delete, on your PC, all copies of VENDOR.XML...there will be at least one, and perhaps 2, and they will be located in or similarly to (it changes based on your Windows version) these folders:
    C:\Program Files (x86)\Common Files\Research In Motion\AppLoader
    C:\Users\(your Windows UserName)\AppData\Roaming\Research In Motion\BlackBerry\Loader XML
    Now, try these tricks:
    KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
    KB27956 How to recover a BlackBerry smartphone from any state
    http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
    If any suggest an Update Website, substitute please either the Desktop Software or LOADER.EXE.
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Frozen White Screen on Email

    I have a frozen email screen (plain white) - have done a reboot, restart, delete account - all without success. Any ideas..??
    I tried to copy multiple copies of photos (c. 30) into an email as images and unfortunately the email is now frozen as a white screen.
    I have done the top button and swipe reboot, top and bottom button reboot, deleted the account and reinstalled - all no joy....!!
    However I have managed to attach a photo to an email and send it from the photo area.
    My email is an exchange type connected to a 3rd party server.
    Help....!!

    Hello nickgurr,
    Welcome to the Apple Support Communities!
    I understand that your Mail application is only showing a blank white screen. I also realize that you have done a lot of great troubleshooting already. One troubleshooting step I would recommend, if you have not already done so, would be to force the Mail application to close. After forcing it to quit, please try and open it fresh and test out the situation. 
    Force an app to close in iOS - Apple Support
    Cheers,
    Joe

  • Frozen white screen

    My Ipod (black 60 GB) has frozen, displaying only a white screen. I´ve tried to reset it several and the screen goes black for 10 seconds and then comes back white again, connect it to my Mac with no result and I´ve let it wear out the batteries only to return to a white screen when I turn it on. Please help me.
    Mac G5 dual 2 GB   Mac OS X (10.4.7)  
    Mac G5 dual 2 GB   Mac OS X (10.4.7)  

    Welcome to Apple Discussions!
    You need to get the iPod into Disk Mode first...
    Putting iPod into Disk Mode
    And then restore it...
    Restore iPod
    btabz

  • Help!  Frozen white screen.

    my phone appears to be frozen. For a short time, every time I pressed the home button, it went to my phone favorites. Then it just froze with a white screen. Its a second generation Iphone. Have tried all unfreezing tips. Help please!

    Restore is a very standard, very common fix in the world of iPod. You often cannot get around it. This is likely one of those times. I guess your reticence is due to the fact that you don't regularly back up what's on the iPhone, and it is not on your computer?

  • White screen during start up

    I shut down my 21 inch desktop the proper way and when I went to turn it back on I end up with a white screen. You can hear the chime like usual, but then I get a white screen. When I shut it down, it was working properly. What could wrong and how can I fix it?  Any help will be greatly appreciated.

    First boot into Safe Mode, if this does not work boot into both a SMC and PRAM reset several times back to back. Follow the instructions in Intel iMac SMC and PRAM resets. If that does not work then please carefully read the rest of Apple's instructions in Gray screen appears during startup

  • IMac Freezes at white screen during startup

    Hello,
    I was off of my iMac for an hour or two so my screen saver when on.  I went to wake the computer and it was frozen.  I tried using the keyboard and mouse to wake up the computer from the screen saver, but it would not work, so I powered the iMac down manually from the button on the back.  I let it sit for 15 minutes, then I tried to start the computer up again.  Now at start up, I get to a blank white screen with the spinning moving pin wheel, and that is it.  Any suggestions?

    You could try to use SafeBoot mode on startup, essentially you'd hold the Shift
    key down on startup, perhaps you may need to login after waiting quite awhile,
    then continue holding the shift key down until you see a traditional desktop.
    And then use Disk Utility to verify HDD, & repair disk permissions.+ Restart.
    Or if you have a system install-restore DVD, boot from that and have the
    Installer's version of Disk Utility check verify repair the hard disk drive.
    It can also repair disk permissions, too, from the booted version of D.U.
    Then when it is done, choose the startup disk from installer menu options.
    The DVD should eject, but if not, it should be ignored as a boot volume
    after you've chosen the Mac HD as a boot system.
    PS: If your computer is now running a system later than Snow Leopard,
    where no DVD would be needed if it has a Recovery partition in the HDD
    then you could see about booting into Recovery (command + R) to access
    the later system's OS X Utilities, and choose Disk Utility to check/repair, etc.
    These may help.
    Good luck!
    edited

Maybe you are looking for

  • How to place two text fields on the same line in adobe

    I am trying to create a form on adobe and I would like to have two unique text fields on the same line. Is this posible? 

  • Is Acrobat X pro compatible with Explorer 9?

    I just installed Acrobat X in my computer runing Windows 7. The adobe toolbar does not appear on my explorer browser. What may be the problem? What do I need to do to make the adobe toolbar on the Explorer 9 browser? Thank you.

  • Resetting user name and password encrypted in printer memory

    How do I reset my HP printer 8600 N911 series name and password? I have no record in my passwords file that I ever had to set up a name and password, and now I can not use my network folder set-up without one. Thanks.

  • How to install driver for Intel HD on Satellite C660-22V?

    Hi I could not reply below so here is my question. http://forums.computers.toshiba-europe.com/forums//thread.jspa?threadID=68240 As*** I do not know if you work for toshiba but what else am I suppose to do if the driver installed on a new laptop does

  • Raw files from Ricoh GX200

    A black band  appears at the right of imported images along with the RAW label. This needs to be cropped before export with the consequent small loss in file size. Why has this appeared? Thought it had been sorted when I did the last update to Apertu