TS3899 sometimes my sound doesnot work.i m using 4s

hi i have been isuing iphone 4s nearly 2 years.i m enjoying with the phone.but last month i was upset with the sound service.suddenly the sound doesnot work .i cant hear any song or ring tone.even though the sound key does not work.after half an hour the sound comes again.the problem occur almost every day.i m staying now in bangladesh.thesomethingre are no applle store in our country.my phone is my besr frnd but now it often make ****** me off.plz do somthing plz

Hello muzaherul hoque,
I would start troubleshooting your iPhone with the following steps:
Verify that there is nothing plugged in to the headset jack, including headsets, headphones, or adapters.
Make sure the Ring/Silent switch is not switched to silent.
While on the Home screen, adjust the volume buttons. If you see the icon below, indicating that headphones are attached, there may be debris or an object lodged in the headset jack:
Check the headset jack. If there is an object lodged in the headset jack that is not easily removed, have the iPhone serviced to remove object.
For Original iPhone: If there is light debris, such as lint, in the headset jack, try connecting a pair of headphones to the headset jack and then remove the headphones. Repeat this several times to remove the debris.
If you have installed a protective film on the display, either ensure that the receiver is not covered or remove the film completely.
Check the receiver mesh (which is on the top front of the device, above the display). If it appears blocked, use a clean, small, dry, soft-bristled brush to carefully and gently brush away any debris.
If you have paired with a Bluetooth headset that is nearby, either use the headset or turn Bluetooth off (choose Settings > General > Bluetooth).
Restart the iPhone.
If restarting the iPhone doesn't resolve the issue, try restoring the device.
If the issue persists, go to the Service Answer Center - iPhone for information on service.
via: iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
Sincerely,
Delgadoh

Similar Messages

My recorded sound doesnot work

when i try to record something through my webcam there is no sound and also when i use my oovoo the microphone doesnt work but my speakers work just fine

Hey Molly, Most of the time the switch inside the headphone port gets stuck open, so your iPod thinks the headphones are plugged in. First inspect the port for foreign debris, if you see something, try to blow it out. If you must with a toothpick carefully remove the debris. If it appears clear, then quickly plug / unplug the headphones about 12 times to free the switch. You may have to repeat. If that does not solve try resetting. Press and hold the power and home buttons until the Apple logo appears. Usually around 10 seconds+/-, then release both buttons. Or go into Settings>General>Reset, then tap Reset All Settings. For the next two options, make sure you backup the iPod to your computer first then, restore the iPod from backup. Last resort, Restore to New. If none of the above work, then you most likely have a hardware issue. Contact your Apple store, and setup an appointment to have your iPod evaluated. Good luck. Cheers.

How do I get my sound to work in Vista using bootcamp? It says no audio output device is installed.

I installed bootcamp on my macmini and am using Vista, but it my sound won't work. It says no audio device is installed.

Realtek Drivers
Cirrus realitypod mac audio driver

Sound not working & iTunes won't play & Netflix error

Sometimes my sound stops working, and songs on iTunes won't play when this happens. Also if I try to watch Netflix an error message comes up: "Netflix Playback Error N8157 3140" and it says it could have something to do with my Silverlight plugin.
This is what it says:
The error you're seeing is related to the Silverlight plugin, which Netflix uses to play movies and TV shows on your computer.
This error is usually caused by one of two things:
A computer setting preventing Silverlight from storing files it needs to play your movie or TV show
An issue with the Silverlight plugin itself
To fix this error, follow the steps below for your Windows or Mac computer.
Reinstall your audio card drivers
Your audio card drivers may be out of date or corrupt.
Uninstall and reinstall your audio card driver. Your owner's manual or audio card manufacturer's website can help.
However, I have tried deleting and reinstalling silverlight, but it doesn't make a difference. Does anyone know what I can do to fix this? It only happens sometimes, other times I have no problems and it works fine.

Back up all data before proceeding.
Triple-click anywhere in the line below on this page to select it:
~/Library/Application Support/Microsoft/Silverlight
Right-click or control-click the line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item selected. Quit the application if it's running. Move the selected item to the Trash. Relaunch the application and test.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.

Sound only works from one port

My sound only works when I use the output port on the back of my computer, but I'd also like to use the one at the front of my computer for convenience. What setting am I supposed to change to do this? Here is some information about my system.
~ > cat /proc/asound/version
Advanced Linux Sound Architecture Driver Version 1.0.24.
~ > aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: VT1705 Analog [VT1705 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 2: VT1705 HP [VT1705 HP]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
My guess is that I want to use device 2 of card 0, so I tried creating a ~/.asound.rc containing
defaults.pcm.device 2
but this didn't seem to do anything.

The "Front" channel isn't the same thing as the front panel. From the ALSA wiki:
"Front, Surround, Center, LFE (subwoofer) and Side (these are the names of the channels with Intel HD Audio, they may vary with different hardware)."
How many sounds cards do you have?
[dspider@arch ~]$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: NVidia [HDA NVidia], device 0: HDA Generic [HDA Generic]
Subdevices: 1/1
Subdevice #0: subdevice #0
[dspider@arch ~]$
What are the other HDMI devices? The video card?
And have you tried googling the problem?
http://ubuntuforums.org/showthread.php?t=1462288

Can't get sound to work on Firefox, but it works with Explorer.

I have a PC with window vista. I recently did a repair on vista because of malware. All normal except now I can't get the sound to work when I use Mozilla Firefox as browser. The sound works when I use explorer as browser. I have checked all connections & sound settings that I know. Help.

Facebook needs Flash to upload photos for drag and drop method.
Please check if all your plugins are up-to-date. To do this, go to the [http://mozilla.com/plugincheck Mozilla Plugin Check site].
Once you're there, the site will check if all your plugins have the latest versions.
If you see plugins in the list that have a yellow ''Update'' button or a red ''Update now'' button, please update these immediately.
To do so, please click each red or yellow button. Then you should see a site that allows you to download the latest version. Double-click the downloaded file to start the installation and follow the steps mentioned in the installation procedure.

ADF : Valuechangelistener doesnot work sometimes

Hi,
I do have a jsp page with three iterators in it. I do have a <af:inputFile component in the jsp page with a 'ValuechangeListener' which does some action. Below this component, I have a command button which uploads the document. But as the valuechangelistner doesnot get executed, I always get null pointer exception.
Could anyone please tell me why valuechangeListener doesnot work in here?
Thanks,
Haripriya.S

... here's the expected snippet from the documentation
<af:form usesUpload="true">
<af:inputFile columns="10"
valueChangeListener="#{backing.fileUploaded}"/>
</af:form>Frank

AUDIODG.EXE hogging 80-100% of CPU and sound not working in Vista . . .

I posted this on a Microsoft Answers Forum but none of the techs or people reading have been able to help so far. I'm dying to get to the bottom of this:
Here is my computer:
MSI K8N Neo4 Platinum
AMD Athlon 64 3000+
2GB RAM
XFX GEFORCE 6600 GT 128MB DDR3 DUAL DVI & TV OUT (PCI-E)
200GB WD SATA HDD
500GB WD HDD in external enclosure via USB2
NEC ND-3520A 16X DVD±RW Dual Layer DVD Burner
LG CD Burner
I've been using Vista Home Premium successfully for some time. Recently, not too long after I did a clean wipe of my OS, my audio would stop working. The way it would happen is that everything would work fine until I started iTunes or another audio application and when I would hit play, things would lock up.
Upon inspection of my system resources, I'm noticing that the audio platform for Vista, via the audiodg.exe, is using close to 100% of my CPU resources, even when the computer is making no sound at all.
I've had a Sound Blaster Live! card in my computer for some time but I was not using it; I use the Realtek AC'97 audio drivers that are on my motherboard instead. I thought that the conflict may be the computer wanting to recognize my Sound Blaster, so I took it out of my computer but the problem seems to be worse.
Are there any BIOS setting that need to be adjusted for my sound to start working again?
I'm very reliant on the audio processing power of my computer (I'm in the radio industry, part-time) and this is a huge drag on my productivity.
Any tips would be much appreciated.
REPLY #1:
Thank you for using Microsoft Answers forum. I suggest going to the manufacture of your sound card and download the latest drivers and install them.
MY RESPONSE:
Good suggestion. The problem is this:
I am running on-board audio. I have an MSI K8N Neo4 Platinum motherboard which runs "Realtek ALC Series AC97 Audio Driver" and there is no version for Vista. They have a version for Windows 2K/XP and one for Windows XP 64bit.
Should I use on of those and if not, then what?
UPDATE (from me):
I took a chance and found a Realtek AC'97 driver for Vista.
http://drivers.softpedia.com/progDownload/Realtek-AC-97-Audio-Codec-Driver-Vista-6183-Beta-Download-18114.html
I went to install it and the install hung. So, I closed one of the install windows and then the InstallShield app continued like it was working. So, I hit "Restart my computer". Well, the reboot hung too. So, I reset the PC manually.
When the computer came back up, the sound worked. Hard to tell if this will fix it for good but it's promising. Chaotic. Unpredictable. Annoying.
REPLY #2:
Before you tried updating drivers, did you try rebooting 1st?
I'm just trying to determine if rebooting your system is what resolved the issue - thank you
UPDATE II (from me):
My computer is behaving the same way it was before. AUDIODG.EXE taking up 80-100% of my CPU and the sound not working.
Any other ideas?

Small update: Despite my intelligence, good looks and vast experience I use Google sometimes. To my surprise this file turns out to be a Windows one. Here is someone who is much happier, and since it is some way in my line of thinking I'll quote it, but you might take my previous advice as well:
http://forums.techarena.in/windows-vista-performance/1012315.htm
"- Open up msconfig.exe > Manage startup programs.
- Disable ALL Realtek entries
- Close msconfig.exe
- Right-click on the speaker icon > Audio devices > Speakers (properties)
- Go to the enhancements tab
- Check the box to disable all audio enhancements
- Close the menu
- Right-click on the speaker icon > Recording devices
- Disable all your microphones (yeah..., the actual problem seems to come
from voice inputs rendering..)
- Close the menu
- Restart your computer"

Macbook Pro Sound not working with HDMi

Hello, I have an early 2013 Macbook Pro on OS X Yosemite (10.10), 3 GHz Intel Core i7, 8 GB 1600 MHz DDR3. If you need more specifics about my computer, please let me know. I use an external LG monitor and separate external speaker, all connected through HDMI (I connect the speakers to the monitor, and the monitor to the computer using an HDMI cable. I find that sometimes the sound just cuts out sporadically and unpredictably. I'll be playing a game, and all of a sudden there is a pop and no sound thereafter. I have to restart the game in order to get the sound back. Sometimes I'm using Chrome and watching Youtube and the same thing. I'll have to restart the program to get sound back. Other times, I have to restart the entire computer because sound is missing from the entire computer.
I've tried switching the sound outputs back and forth from "internal" to "external monitor", with no avail. I've also tried plugging in my earphones (and the sound works), and unplugging them, and the external speaker sound still won't work. After a program or sometimes computer full restart, then the sound will work fine. What can possibly be the cause of this?
Thanks!

go to display, preferences, while the tv is hooked up to the computer. two boxes will come up, one for each screen respectively.
on the tv that you want to correct, go to color, then calibrate, and then change the colors through that.
Your tv may also not have the default colors on. you may want to look in your TV's setup menu and make everything go to default so you can start fresh and clean. Some TVs will save setting specific to an input and that would explain the weird colors.

Alert sounds not working in iPad

My iPad does not play alert sounds and line2 does not send push notifications with sound until i open the app. Maybe the app but does anyone else have this issue? I have gone to settings/generalsound and set the "Ringer and Alerts" section sound to wide open and I turned the "Change with Buttons" to off. Does anyone else have this issue. I was not really looking forward to restoring a back up copy but I might have to.

I have found the answer to my own problem...listed here in this discussion: https://discussions.apple.com/thread/3008964?start=0&tstart=0 it has to do with the lock mute/rotation button. When the selector switch is on lock rotation alerts will not play sound. Also sounds in apps and sometimes video will not work unless you are listening through head phones. This bug has existed for a while according to the post in the link.

Sometimes my internet will work then it won't i dont know whats happening how do i get the internet to work

sometimes my internet will work then it wont how do i get it to work probably

You could try a PRAM reset. Hopefully it'll restore the sound as you need to release the keys after the second chime:
Reset PRAM
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P and R.
You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

I have pavilion dv6 sound not working hp provide new update idt stil not working

HI .
i have pavilion dv6 sound not working hp provide new update idt stil not working

Go to the link below.Enter your Product Number as listed on Service Tag attached to bottom of notebook (may be under battery). You can also get the Product Number by pressing Fn + Esc key. After entering PN, click Next ,then choose Software & Drivers.On the next page use the dropdown to select your OS (probably Windows 7 64bit). A list will populate with drivers. Download & Save the latest Audio driver.
http://h10025.www1.hp.com/ewfrf/wc/siteHome?cc=us&lc=en
Go to Control Panel,Programs & Features-Uninstall IDT software and restart the laptop.Next install using the downloaded file.
```````````````````````````````````````
If still no sound,try a hard reset, works sometimes.Disconnect all external devices first.
1-remove power cord and battery
2-press power button for 30 seconds
3-reinstall only power cord for first startup.
4-power on
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Will my new sound card work with windows 7 64 bit??

I had creative sound blaster xtreme music, it use the old pci port. It has been giving problems ever since i got a new computer with windows 7 and a gigabyte mother board. The computer will sometimes not detect the car, when it does i will work for a while then a beeping sound plays, or sometimes i wont have sound at all when it is detected. Anyway, I am upgrading to the PCI-express xfi champion card. Is this card going to work with windows? 7 and not give me though problems?
Computer detais:
i7 930
Gigabyte - UD7
Radeon HD-5870

It will work,as I have one on Win 7 x64. Without problems is another story.
There are plenty of posts about this card.Have a look around.

Soundblaster X-Fi Surround sound not working!!!! HELP!!!!

9Soundblaster X-Fi Surround sound not working!!!! HELP!
!!! officially i hate creative to the what was supposed to be simple registration which in itself annoyed me to now the speakers i have been using for a longggg time for the past 4 days has been bothering me..
Using a Creative Soundblaster X-fi ?sound card with a 7. surround sound speaker set-up and windows vista ultimate (32bit) the sound refuses to come out of all the speakers during the channel test it sometimes picks up certain speakers but never all of them and the sound is pretty much coming out of the left speaker only i've tried uninstalling all the drivers installing every driver i can find together with the console launchers i've changed the config settings in windows itself which doesnt help uninstalled all codecs bought another x-fi card (i was getting frustrated) still nothing the only thing i havent done is re-install windows which i refuse to do because of some creative defect!
I hope someone has a solution or any advice would help i've also used dri've cleaner and sweeper to clear all data from the registry etc rebooted etc etc etc still no luck....
Sort it out creative!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!

**beep** !! a response would be GREAT............
Admin Notes: I understand that you are frustrated but cursing & swearing is not allowed here. If you need help from customer support, you can contact them through email. Please abide to the rules if you want to participate in this forum.
Message Edited by KokChoy-CL on <span class='local-date'> 02-7-2009<span class='local-time'> 09:50 [email protected]

HP Pavilion dv6775-Vista-Internal sound not working-External sound is OK

Hi All,
I searched through this forum and just realised that I am not the only person with this problem. Sometime back the sound of my laptop (dv6775us) stopped working. However the external sound systems work fine when connected. I have done whatever was mentioned on HP support site/Microsoft site etc. i.e checked the device driver, reinstalled etc. While running the diagnostic everything seems normal. Anybody has any clues, please help.
Thanks in advance.

Hi I just fixed the same problem I found that the sound card was enabled but the speakers were disabled.
go to control panel sound playback then right click in the window and check show disabled items. It was here that my speakers were disabled. hope this helps you.

TS3899 sometimes my sound doesnot work.i m using 4s

Similar Messages

Maybe you are looking for