Tsclient drive redirection fails after wrt54g firmware update

Recently updated firmware on WRT54g wireless router. Ever since am unable to redirect drives in rdp client session to 2003TS. The drives show up as "system folder" on the server, no drive letters visible, not accessible.
This happens with all PC's on my home network. If I shut down my wireless router and poach a neighbors connection using my laptop the drive redirection works as before.
Any ideas?

Are you able to access the drive before upgrading the firmware ?
If yes, reset the router as it is recommended by Linksys that you should reset and reconfigure the router after resetting .
Press and hold the reset for 30 seconds .
Power cycle the router and modem .
Open the setup page of the router and configure it again .

Similar Messages

SoundBlaster X-Fi Driver Installation Fails After Moving Soundcard to New Slot

NSoundBlaster X-Fi Driver Installation Fails After Moving Soundcard to New Slot4 I recently moved my X-Fi Elite Pro soundcard to a different PCI slot to accommodate my new large PCIE graphics card.
Prior to moving the card, my?original SoundBlaster install went fine without any trouble. When I booted up after relocating the card,?it was not detected at all. So I uninstalled my SoundBlaster driver software and?rebooted the computer?thinking that was necessary to clear any hardware configuration settings from the old install. This made no difference. I then discovered my card was not seated properly and corrected it.
Next I installed the SoundBlaster driver software. The installation proceeded and finished with a request to restart the computer. Once I did, the computer detects my card and starts the hardware installation wizard asking if I want Windows to search online for driver software. It does not recognize the just installed SoundBlaster driver installation. I have a dual boot setup and this happens in both WinXP Pro and Vista 32 Home Premium.
What's wrong here?

Forget it folks...couldn't wait for any suggestions so I just cleaned off my hard dri've and reinstalled everything. Works fine.

After a firmware update to airport express should I unplug the unit then plug it back in? (bascially reboot it)

After a firmware update to airport express should I unplug the unit wait a bit and plug it back in? (basically a reboot)

I updated the firmware on the 2nd of this month. Everything was fine. About a week later internet speed began to be slow. I rebooted the modem and the speed was okay for awhile, then slow again. I'm wondering if it's the airport express. It didn't tell me to reboot at the end of the installation.

Wlan error after a firmware update

Ok there seem to be many posts about this issue but i cannot find anything that seems to work for me.
I not to recently updated my N95 8Gb firmware to 20.0.16 and found that I was having errors with WPA on WLan, previously I had no such problem and the issue only occured after the firmware update.
to add some more info I am on a network with a linksys wrt300n
I have tried wep it works but dont want to compromise security.
All computers on the network are using wireless g and the key is definitely correct when entered
any help would be most appreciated

I don't have N95, but if the firmware is updated to latest version the wpa most likely wpa2. Having wpa in place of wep gives only very little added security for a determined hacker! It will only takes 30min to an hour to crack that. Security like that deter only the free net riders. Try if there is upgrade for your modem/router, its usualy the case. For home network wep or wpa sufficed.
Knowledge not shared is knowledge wasted!
If you find it helpfull, it's not hard to click the STAR..

Incompatible after the firmware update

I had missing the dictionary (including the icon on the screen) and chinese language currently stored in my nokia 6680 after the firmware update. what is the problems?

Yes I m using one of the default themes.
I have even done the re-installation of the same firmware version again, it did not work.
Each time I flash the firmware, installed applications become unworkable although the icons still remained in the menu. IT is always a great hassle to have to re-install all applications over again.
tsk.

Bluetooth doesn't work after E90 firmware update!

Nokia staff - help needed!
Bluetooth has stopped working after E90 firmware update.
The following on-screen message is shown: "Unable to perform Bluetooth operation!"
P.S. Reinstalling firmware via Nokia software update doesn't help at all. If connectivity problem still can be solved with USB cable, the worst tning is that I can't use my phone's BT handsfree when driving.

Hi hanzzi
No information as to what device you are using, but try deleting E:\CITIES + .qf file from memory card then restart OVI Maps application to re-define folder structure required to download regional mapping using OVI Suite.
Happy to have helped forum in a small way with a Support Ratio = 37.0

TC reporting "Hard Drive is Failing" after Firmware update to 7.6.1

I've jumped in and updated my TC and expresses. Everything is working it would seem, however I'm getting intermittent amber alerts on the TC now saying the hard drive is failing. Time Machine backups are happening fine, no problem mounting the drive and the alert goes away after a few minutes. I've read other posts previously about this behaviour but never had it myself. Anyone else having this problem?

AT & T is infamouse for its out-dated PPoE technology. Still don't get how a company that big can still be so behind the times.
Unfortunately, I'm at the point when someone mentions AT&T and internet issues, I just cringe because 9 times out of 10 it's one dreaded PPoE problem you're going to get stuck into, or another.
Good luck with it...

HDD clicking after EFI Firmware Update 2.7

After I did the EFI firmware 2.7 update and the my macbook pro restarted, I noticed that I started to hear a clicking noise from my laptop. At first, I thought it was a normal sound that I may have not heard before but I checked my other laptops and they aren't making any noise close to this. The other two laptops I checked were also early 2011 models, one 13" and the other is 15".
Here is the recording of the sound.
http://dl.dropbox.com/u/108564/iPhone/Memo.m4a
There is some background noise but that clicking sound is the sound I hear. This is recorded with my 4S with the mic hovering around the palm rest and trackpad. I also noticed that when I tilt the laptop, I can hear a grinding sound. I tried to replicate this grinding noise on my other MBPs but I can't replicate it.
What is the best option for me? If I take it to Apple, would they actually be able to replace it for me or resolve the issue? I don't want to waste my time driving 45 minutes to Apple just so they can say it's "normal". Has anyone had this issue before and taken it to Apple?

Pretty nasty, sounds quite regular. Drives don't make that sound normally, sounds defective.
What is your machine specs, opeating system version etc.?
If your drive is grinding, that's a sign it's going to die soon, so you need to backup immediatly.
EFI 2.7 might not be the sole cause, especially if others don't come forward and report the same issue, but might have attributed to something pre-existing.
There has been a unusually high number of issues with the latest EFI firmware updates, why I don't know.
Perform a hardware check, rule out anything else.
http://www.cbscores.com/index.php?sort=ogl&order=desc
You might have a warranty call if the drive is failing.

After EFI Firmware update 2.3, MBP Early 2011 will not boot. During restart it all went wrong please help!

Hello,
I've done an ample amount of Internet research to find an answer to this problem however nothing yet found is quite like this. I will start from the beginning.
I am traveling through Europe, and I normally live in California. When I arrived in Ireland my MBP early 2011 15 inch, began crashing constantly when I had several tabs open on Chrome and maybe one or two low CPU/Memory using applications, nothing the 8gb RAM &750gb hard drive can't normally handle. Thus I began trouble shooting. I ran disk utility once started up and repaired both disk and permissions. Still crashing. It didn't seem like it had anything to do with a kernel panic shut down, I never would receive the usual message indicating so. After that I did an SMC reset. It was still crashing. I then upgraded the OSX from 10.8 to 10.8.4 believing it could help. It did momentarily, but then crash again. (When it crashes screen goes black suddenly and upon pressing power button does a regular boot on my single partition). I decided attempting to repair using the Internet recovery option but it appeared my MBP had not yet have it installed, so I downloaded from Apple and began installing. Here I made a mistake, I unplugged the power source as it was restarting. When the gray screen and apple appeared, the loading bar shows up as it says it will when installing the update, but when the bar fully loads it crashes every time. I've tried starting in safe mode, which then loads but never goes further (I let it stand for two hours such as that and nothing). Then I decided to allow the MBP to fully charge overnight to give it time and charge. This morning the problem has stayed the same, even with power source plugged in. Please help I need this to work.
Thank you and please ask any questions!

Your constant crashing problem is probably some type of hardware fault which no update can fix. Doing the 10.8.4 update and then the firmware update just caused further problems. you need to take thr system to a apple store to be diagnosed and fixed if cost effective.

Windows 7 x64, MacBook Pro, frequent CHKDSK after HDD firmware update

Hello, I have been having filesystem problems on my Windows 7 partition since the HDD related firmware update (the latest Performance update) was released and installed onto this mid 2009 MacBook Pro.
The HDD is a 500 GB 7200 RPM model, but it never gave me any troubles under OS X before the "fix" and I know other users had intermittent problems with the HDD on their MacBook Pro's related to the HDD making noises and pausing.
The fix was released, I installed it and I started seeing my first problem in Windows 7 x64 a few days after... I cleanly shut the OS down, but when I booted it back it asked me to perform a coherency check to the Filesystem... I thought that the problem was related to the fact that I was using the RC1 build of Windows 7... although that problem never manifested itself in the weeks before the Performance Update (HDD firmware fix) was installed and Windows 7 x64 RC1 had been on there and used frequently.
I recently purchased Windows 7 retail a few days ago and after a bit of trouble-free operation I started having problems again... always shutting the PC down carefully and I was asked to run the CHKDSK utility at boot twice already.
What to do?
Message was edited by: Panajev

Hi there,
I have a different experience. I installed Windows 7 before the "performance update 1.0" came out. I actually experienced the chkdsk launch problem with Windows 7. I had done repartitioning and clean-install several times but cannot solve the problem. So I tried to install XP and Vista on my MBA (Mid 2009 with SSD) and found that these two OS doesn't introduce such problem.
To be honest, I'm not sure which caused such problem, Windows 7, a bootcamp driver, or EFI. But I'm sure that CHKDSK in Windows 7 has an obvious bug that needs to be patched (memory leak and maybe this problem as well). So now I'm using Windows Vista SP2. And I'm happy with Vista SP2 (seems to become faster and stable now).
Cheer,
Message was edited by: nicegom

Mac Mini doesn't startup after failure firmware update..

Hello.
I have a mac mini.
Downloaded firmware update and Mac OS X update through MAC OS X Software Update.
After that my Mini Mac ask me to restart.
And now my display shows "No signal" message and no startup sound. Indicator lights up, can hear Hard Drive sound and DVD disk sound, optical mouse lights up... and nothing else.
I tried to reset PMU... nothing again (

Hey Guys today i updated my macmini from 10.5 to 10.5.2 i downloaded the file 343MB on http://www.apple.com/support/downloads/macosx1052comboupdate.html since i have a slow connection i took me 5 hours to download the file after installed and and saw the success intallation with a green checkmark then restart and it presented me a blank white screen as i was reading the discussion i read that just leave it as the OS is doing it's thing but there is no indication whatsoever just a blank screen. then i saw my SD card reader blinking i remove it thinking that its the cost why there is now indicator that the HD is still reading so ive waited for 30mins without touching a thing and finally i heard the CHIME OF RELIEF the apple logo flashes and I have installed my OS 10.5.2 successfully

WRT54GS firmware update

Hi
I just updated my WRT54GS v2.1 from firmware v4.50.6 to v4.71.4 (yes, I'm not what they call the most careful network admin in my house), and I noticed 2 slight changes, I'd like you to confirm:
1) On Setup tab, Basic setup page, I remember from previous version what was specified on Router name would be shown on "Connect to 192.168.1.1" login window, e.g. "The server 192.168.1.1 in ROUTERNAME requires a user name and password". After firmware update , it shows WRT54GS, ignoring what's I specified in Router name field. Is it same to you?
2) On Status tab, Router page, it says "Current time: Not available". Help says "This shows the time, as you set on the Setup Tab". Setup tab only shows time zone setup though... I don't recall if it was available there in previous firmware version, but where is the clock adjust function?
Thank you!

After upgrading the firmware on the router, it is recommended that you should reset the router and reconfigure it. Press and hold the reset button on the router for 30 seconds. Release the reset button and wait for 30 seconds. Power cycle the router and reconfigure it.
On the setup tab, you will find the Time settings.

Weird problems after SMC firmware update

Hi,
So I have a MacBook Pro bought in July 2007. I installed the new firmware update yesterday and noticed today that my computer gets a lot warmer. If I try to run an application that does more processing, some buttons on my screen turn black, I can't move windows and the backlight starts to flash like crazy giving me a nice disco effect if I turn the lights off.
/var/log/system.log will show stuff like the following:
Jun 2 20:33:59 edvard-fagerholms-macbook-pro kernel[0]: NVDA(OpenGL): Channel exception! status = 0xffff info32 = 0x1 = Fifo: Fifo Method Error
Jun 2 20:34:00 efagerhos-macbook-pro kernel[0]: 0000000b
Jun 2 20:34:15 efagerhos-macbook-pro kernel[0]: NVChannel(Display): Graphics channel timeout!
Jun 2 20:34:15 efagerhos-macbook-pro kernel[0]: NVDA(OpenGL): Channel exception! status = 0xffff info32 = 0x1 = Fifo: Fifo Method Error
Jun 2 20:34:15 efagerhos-macbook-pro kernel[0]: 0000000b
Jun 2 20:34:59 efagerhos-macbook-pro kernel[0]: NVChannel(Display): Graphics channel timeout!
All my problems started after trying an application written in Java, which seemed to require lot of processing power and made my computer very warm. After this I have also been unable to get my DVD drive to read any DVD. If it turns to be the update, I am pretty ****** of that they release an update that can physically kill a perfectly well working computer. Especially, when it's already out of warranty.
Does anyone else experience any similar problems?

I am pretty sure it's the graphics even though the Apple "genius" claimed it wasn't. The genius told me the RAM chips were broken. Ok, so I bought new RAM, the computer booted up, worked for about 30 minutes and the problem came back.
However, the computer boots up flawlessly to single-user mode by pressing apple-s during boot (even with the old RAM), so I can access the disk and use it as a typewriter in the console... I also coded a poor mans memory tester that allocated memory and wrote random stuff to it, and it worked fine with my old RAM chips. If I try to start the machine normally, then according to the logs, the computer freezes at the exact moment when it's starting up the login screen. If I assume correctly how OS X works, I would suspect that this is the moment it switches from some kind of a video BIOS framebuffer mode into an accelerated mode provided by the nvidia graphics driver.
I also noticed after using the root console in single-user mode for about 30 minutes (I was making a Linux USB stick to start it through rEFIt, to do some further diagnostics) that the black console background had these faint blue horizontal lines going from the top of the screen to the bottom. This is usually a sign that the graphics chip is busted.
It seems like it's time to get a new appointment in the Genius Bar.

After odd Firmware Update won't accept CDs

I updated with the Firmware Update and it was an odd update - it just seemed like it didn't work correctly. I don't know how to explain it, but it just didn't. After that update, my computer wouldn't turn on, I just had a gray screen. I searched and reset my PRAM. All seemed okay. The computer is turning on correctly and not having the automatic shutdown problems others have posted.
This AM I tried to insert a CD and it won't let me! I've not had problems before.
I tried to find a way to remove the Firmware update to install again to no avail. When I tried to reinstall it again I received the message that it was already installed (this was after I had removed it from the applications folder even).
Any help is appreciated. Thank you!

Sorry: the above is (partly) wrong ... - it'll get you past the firmware update but won't get you past the Boot Camp Assistant ... - it wants to see a single partition No matter what ...
[Just for that, I'm gonna see if I can mess with the 'can't do this on an external drive' requirement ... by moving an external to internal then back out again grin)
best of luck...

Internet stopped working on MBA after latest firmware update. Help please!!!

Internet stopped working after installing the latest firmware update. WiFi still connects to router, our other mac desktop still connects to internet as usual (same network). I can't even re-install the MBA OS since it needs an internet connection!!!
Any ideas?

FIXED.
I swapped our wireless router for a newer one, internet seems to work fine again (we were sent a new one by our internet provider which we never set up until now).

Tsclient drive redirection fails after wrt54g firmware update

Similar Messages

Maybe you are looking for