TTL level only 1.3V out of 8255 port A

I am using a PCI-6025E to do time critical triggering of various devices in my measurement system. I am using handshaked output using the 8255 ports. The voltage level for the the high state is 1.3V. This does not reliably trigger by NI PCI-1411 frame grabber board. If I use a function generator with a 4V high, it triggers every time. Note: I have checked the trigger signal out of my PCI-6025E and it looks good except for the low voltage. My question is this: "Is the high state from the 8255 ports supposed to be so low?"
jc
Mac 10.4
LV7.1
CLD

The problem was that I was measuring the voltage across a 50ohm impedance on my oscilloscope. When I switched to 1Mohm, it the voltage went up to 5V, as expected.
jc
Mac 10.4
LV7.1
CLD

Similar Messages

Load the Budget value at cost center level only

Hello All,
Can we load the budget value at the cost center level only with out using cost element . I have seen that we can from actual to budget in Kp98 at the cost Center level.
Thanks ,
Krishna

Hi
There is a work around...
You can create one Statistical IO for each cost center and upload your budget in it...
Keep the same nomenclature for IO as the Cost center i.e. If cost center name is 123456, have the same name for IO as well
In Substitution OKC9, you can use a Field to Field Mapping and populate same IO as the Cost center no in the posting or you can also use exit RGGBS000
br, Ajay M

Capacity requirements generation at phase level only

Hi gurus,
Is there any setting to get capacity requirements generation at phase level only?
At present in my system iam getting for both operation and phase. Since we do confirmation at phase level only, practically system should not generate capacity requirement at both levels.
Please throw some light on this.
Regards
Venkat V

Dear ,
I think you are working in a PP-PI system .There are operation control key which can be assinged in the master recipe which will not carry out Capcity Requirement Planning .Goto -spro-define operation control key -Check the PP-PI related Control key like PI01-select that -goto detail information -Check if the Capacity requirement check box should not be marked .Assing that control key which will not allow to do the Capcity Requirement check .
Or else , in master recipe you can choose the control key which does not have CRP activated -go details information befor assing the same
Hope this is clear to u
Regards
JH

Restrict Collaboration tab page view at project definition level only

Hi,
I have a requirement where the cProjects user should be able to view the Collaboration tab page at project definition level only & not at the phase, checklist, checklist item or task level. This is to prevent the user from assigning/creating collaborations at a level other than the project definition.
Is there a way out to get this setting done & how?
Regards
Deepak

My proposal is that you modify the logic in
CL_DPR_BSP_S_PRO_TYPE
Method SHOW_COLLABORATIONS
a small I condition here can control the tab view hide/unhide feature.
or modify the BSP page and take out the complete call
in
phaDetail.bsp
tskDetail.bsp
etc.
Message was edited by: Björn Kettner

Hello i just came back from the apple store and they had to restore my phone and i just downloaded all my apps and music back but my photos that are on icloud i only got 80 out of 768 back. what do i do to get all of them back?

hello i just came back from the apple store and they had to restore my phone and i just downloaded all my apps and music back but my photos that are on icloud i only got 80 out of 768 back. what do i do to get all of them back?

If you tried to restore to your iCloud backup and your photos didn't fully restore, first go to Settings>iCloud>Storage & Backup and make sure it isn't still in the process of restoring.
If the restore is complete and all your photos weren't restored, all you can do is try restoring the backup again. You might try the solution posted by ezjules in this discussion: https://discussions.apple.com/message/19518589#19518589. This involves opening the photos app after the phone restarts and you provide the passwords for your Apple IDs, then leaving it open for the remainder of the restore process.

Is iCloud really a backup service? Because I can only retrieve 60 out of my 600 photos.

Hi, my girlfriend was robbed of her iPhone and now we want to retrieve the pictures from iCloud to her new iPhone but it only retrieves 60 out of 600 from the Photo Stream. According to iCloud the latest backup was made 22nd of January.
Does it only retrieve from the last 30 days? (I read that somewhere)
If so: how can you call it a backup service?
And why is her 5 GB storage filled up if I only had 60 photos on there?
And why can't you just let the users browse among the backed up data. It is more likely that you look for single documents rather than your whole backup. Especially as you usually make backups on computers sometimes and fill your phone with new pictures and then there is no space to restore anymore.
It says - backup your photos - in your slogans and promotional texts. Perfect! - I thought.

If the songs play ok in iTunes make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

"Multi-level error propagation carried out" in SCM 5.0

When I use the SNP PPM Generation With Lot Size Margin function in SCM 5.0, I got the following error:
Multi-level error propagation carried out
Message no. /SAPAPO/OM242
Could you please give me this help?
Thanks,
Lian

Hi,
Thank you for the information, but the problem is still there though I de-activated all user-exits...
I also saw the following error:
Invalid planning version
Message no. /SAPAPO/OM015
Thanks,
Lian

Multi-level error propagation carried out Error in APO

Dear Experts,
We had developed a custom program that is same as /sapapo/rrp3 report, but the issue is when we use planning version other then 000 the custom program is giving the error ""Multi-level error propagation carried out"" but the RRP3 report works fine with all the planning versions.
Please help to find the cause and to solve the issue.
Thanks.
Regards
Abhinav Nallani.

Dear Arek,
The problem is not yet resolved . we have raised an OSS note for the same.
as the relevant notes are already implemented in our case.
regards
Kiran

Error "Multi-level error propagation carried out" when I run a report

Hi All,
When I run the report /SAPAPO/CDPS_REPT - Order and Resource Reporting with the below criteria I getting error "Multi-level error propagation carried out"
Planning Version - Simulation Version XXX
Evaluation Start - 05/03/2011
Evaluation End - 12/31/2013
Evaluation List - Extended Operation List
I do not get error when I run the report with selection as Active version 000 and Evaluation List as Order List, Operation List.
I have tried by ruuning Live cache consistancy check, but the issue is not fixed
Please help me to resolve this issue
Thanks & Regards,
Rajkumar

Hi Jack,
Please do post the server log file here so that we can try and find a solution for the problem you are facing.
I had a problem a while ago with the app server too. While trying to run an application, after a few times, it would give me an error message saying the Application Server cannot be started. I rebooted my machine and thankfully it worked again. Just try this too and see if it works.
If it doesnt we can go through the server log and try to identify the cause of the problem.
Cheers :-)

CIF error-Multi-level error propagation carried out

Dear ALL,
When i am trying activate the integration model for Material transfer it generates queue with status SYSFAIL with message "Multi-level error propagation carried out".
and the integration model is not activated.
please help
regards
Kiran

Dear Arek,
The problem is not yet resolved . we have raised an OSS note for the same.
as the relevant notes are already implemented in our case.
regards
Kiran

Just because I have an imac pre 2007 why can I not order photo albums???!! I spent hours building a photo album for my parents only to find out that because my mac is earlier than 2007, even though I have 10.6.8, I can no longer order?! What is that

Just because I have an imac pre 2007 why can I not order photo albums???!!
I spent hours building a photo album for my parents only to find out that because my mac is earlier than 2007, even though I have 10.6.8, I can no longer order?! What is with that? This makes no sense. I can go online to various "photo shop" place and regardless of the OS and computer I am working from I can order a photo album so why can I no longer do this through iPhoto on my MAC?
How do I order my album now? If somebody could please explain as I am going home in 1 month and really wanted to surprise my aging parents with this book.

I found this:
http://store.apple.com/us/help/print_products
Have you tried this?

On a new mail message in Yosemite there is no Send button or icon. Only a grayed out word that says "send. I can receive mail but not send because nothing at top of email allows sending

On a new mail message in Yosemite there is no Send button or icon. Only a grayed out word that says "send. I can receive mail but not send because nothing at top of email allows sending. Please help. This is true of two .me accounts I have.

Hi,
It may pay to send a Screen Shot of the Connection Doctor info. (see the Window Menu)
It would seem the IMAP or POP side is logged in bit the out going STMP server is not.
8:27 pm Monday; December 22, 2014
 iMac 2.5Ghz i5 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

Dv6 Only plays Sound out of the built in speakers if headphones are plugged in ...please help

My Pavillon Dv6 Only plays Sound out of the built in speakers if headphones are plugged in. It plays sound from both when there plugged in. Please hep me.

Step 1:
In troublshooting the problem you may follow the steps provided below.
a. Click Start, type Sound in the Start Search box.
b. Click Sound in the search results at the top of the Start menu.
c. Click the Playback tab. Notice the check mark next to the default device. For most users,the default device is speaker, change it to headphones. Make sure that your audio settings are configured as expected.
Step 2:
On the Playback tab, select the playback device, click Properties, click the Advanced tab, and make sure that the Default Format is set to the value that you expect. When you finish, close this window to return to the previous window.
Step 3:
On the Playback tab, select the playback device, click Configure, and then make sure the configurations are set correctly.
Method 2:
If the issue persists then I suggest you to follow these below mentioned steps to mute all other sounds when windows detects any communications activity.
a. Click Start, type Sound in the Start Search box.
b. Click Sound in the search results at the top of the Start menu.
c. Click the Communications tab.
d. Click on the radio button according to your convenience, under When Windows detects communications activity.
After performing the above steps you may check for the issue.
For more troubleshooting you may visit this below mentioned link.
Tips for fixing common sound problems
http://windows.microsoft.com/en-us/windows7/Tips-for-fixing-common-sound-problems
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

I've downloaded Adobe acrobat standard Dc only to find out it's not compatible w/windows XP. How do I get a different version?

I've downloaded Adobe acrobat standard Dc only to find out it's not compatible w/windows XP. How do I get a different version?

Hi vincelucy,
If you've purchased a previous version, you can download older installers from this page: Download Acrobat products | Standard, Pro | DC, XI, X (you'll need your serial number to complete the installation).
Best,
Sara

HT201364 When I try to download this I get a message that says I haven't got sufficient space on my startup disk. I have checked my available space on the disc and I have only 3GB free out of 500. I have hardly anything on my mac - how can this be?

When I try to download this I get a message that says I haven't got sufficient space on my startup disk. I have checked my available space on the disc and I have only 3GB free out of 500. I have hardly anything on my mac - how can this be?

Freeing Up Space on The Hard Drive
1. See Lion/Mountain Lion's Storage Display.
2. You can remove data from your Home folder except for the /Home/Library/ folder.
3. Visit The XLab FAQs and read the FAQ on freeing up space on your hard drive.
4. Also see Freeing space on your Mac OS X startup disk.
5. See Where did my Disk Space go?.
6. See The Storage Display.
You must Empty the Trash in order to recover the space they occupied on the hard drive.
You should consider replacing the drive with a larger one. Check out OWC for drives, tutorials, and toolkits.
Try using OmniDiskSweeper 1.8 or GrandPerspective to search your drive for large files and where they are located.

TTL level only 1.3V out of 8255 port A

Similar Messages

Maybe you are looking for