Tunneling on cisco 1700 series

Dear all,
I have a cisco1700 series route which contains two ethernet ports.I don't want to use serial ports.I have a broad band connection(i.e. through smart bridge). One etherent is connected to smart bridge. & other one to lan.
How can i configure the router by using tuneling so that i can shift all the load on broad band connection?
Pls. provide each step.
Thanks
Tarlochan

Here is a sample configuration for a GRE tunnel:
Router# configure terminal
Router(config)# interface Tunnel0
Router(config-if)# tunnel source
Router(config-if)# tunnel destination
You can have GRE destinations on the physical interfaces or you can use loopback
interfaces as well.

Similar Messages

Cisco 1700 series startup problem

I have a cisco 1700 .After a blackout this router is not configured. After recounfigured router save running-config in startup-config and works fine until new blackout. Any idea ?
Thanks (sorry for my english)

Does it also do the same when you power cycle the router.
Sounds like your conf register is not set correctly.
Do a "show system" and look for "Configuration register is 0x2102" at the bottom of the output.
If its not set to this then you can change it by issuing:
my_router(config)#config-register 0x2102
HTH
PJD

How do I monitor a Cisco 1700 Series T1 Serial Port.

I have a Cisco 1721 Router and I am looking to monitor it for hourly statistics to find max and min speeds. How would I go about doing this? I know if I do a show interfaces it shows me all the data since the last time the counters were reset. Thanks for any help.
Chad
Diversified Telecom.

http://www.paessler.com/
There are many others.

Cisco 1700 Series T1 Point to Point Change Clock Source

So I am trying to change the clock source on my already setup cisco t1 point to point, but it wont allow me to. I have had many people tell me 10 different things that I have to do but no one seems to know how. I put in the command clock source internal, but it says its an invalid command. Any help would be much appreciated.

My current version is....
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV3Y-M), Version 12.2(8)YN, EARLY DEPLOYMENT RELE
ASE SOFTWARE (fc1)
Synched to technology version 12.2(11.2u)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Wed 30-Oct-02 10:22 by ealyon
Image text-base: 0x80008120, data-base: 0x80F47D4C
ROM: System Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SV3Y-M), Version 12.2(8)YN, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
pe-wen-01 uptime is 1 day, 18 hours, 19 minutes
System returned to ROM by reload
System restarted at 10:02:41 PDT Tue Jun 12 2012
System image file is "flash:c1700-sv3y-mz.122-8.YN.bin"
cisco 1751 (MPC860P) processor (revision 0x600) with 36864K/12288K bytes of memo
ry.
Processor board ID JAD06370AF0 (4055773928), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
2 Channelized T1/PRI port(s)
WIC T1-DSU
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102

Test Network Setup with 1700 Series Routers

Hi,
I'm relatively new to Cisco equipment use. Fortunately I have in my possession two spare Cisco 1700 series routers with which I can set up a lab to learn and play.
I'm not sure what cards to get for them--they have none. Can someone offer guidance? My guess is I can get second hand WIC's on e-bay but I'm not certain the models or options I need.
My goals would be to do the following, at a minimum, (I think! I'm open to suggestions on other options or limitations I might face)
1. Configure a routed network between two subnets connected by a router.
2. Configure the routers to connect to each other, as one would do for say a T1 connection between two remote offices, each having a subnet connected.
Right now the routers have no cards.
Best regards,
Will

Will
I can see benefit from having 1 serial link/subnet and 2 LAN subnets, especially in the variety of scenarios that you could implement with that combination of equipment. (all subnets on a router in the same network, 2 subnets in a network and the other subnet in another network, all subnets in different networks, dynamic routing protocols with auto sumarization enabled, dynamic routing protocols with auto summarization disabled, OSPF on the routers when connected by serial interface or OSPF on the routers when connected by Ethernet interface (is there a DR elected in both situations?)
HTH
Rick

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier
These items are listed with 1600 series AP but I'm unable to understand what are these things & the use of them

DHCP Option 60: Go HERE.

How to bridge a linksys cisco E1200 series router?

I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox

purchase 881w, get rid of linksys. That should do it.
Sent from Cisco Technical Support iPad App

Need a tool for flash backup on Cisco 2821 series routers

Hello Folks,
We have around 1200-1500 cisco 2821 series routers on those we are performing the hardware upgrade so we are taking the backup of all the files available in the flash of all the routers, we just want to know is there any trusted tool available to make this task easy to schedule and take the backups.
Please let me know if you know any tool name.
Thanks,
Raja.

Sorry, I don't know any tool that makes a backup of the whole flash...
You could fo it with from ios cli maybe execute it automatically...
To flash:
archive tar /create flash:/backup.tar flash:/
copying directly to ftp should also work:
archive tar /create ftp://test:[email protected]/backup.tar flash:/

Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

Hi All,
Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
Any help would be greatly appreciated.
Thanks in advance.
Samir

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

Can I terminate 40 Mbps DSL BROAD BAND connection in Cisco 800 series routers

Dear all,
Can I terminate 40 Mbps DSL BROAD BAND connection in Cisco 800 series router?.It is not a leased line.
Which Router model is best for 40 Mbps DSL Broad band termination ?
Thanks&Regards
Ajay Jose K

Hi ,
Below link provides you all model in 800 series .
http://www.cisco.com/c/en/us/support/routers/800-series-routers/tsd-products-support-series-home.html
For your requirement below model should suffice .
Complete throughput from the router is 51 Mbps .
Cisco C891FW Integrated Services Router
HTH
Sandy

Which command in the Cisco AP1200 series will you use to broadcast the SSID using VLANs?

Folks,
Which command in the Cisco AP1200 series will you use to broadcast the SSID using VLANs?
Thanks

If you have enabled mbssid, "guest-mode" would be replaced by "mbssid guest-mode" this would also allow multiple ssid's to be broadcast
-Tim
Sent from Cisco Technical Support iPad App

Error in Cisco 2500 series Wireless Controller

I have this error in Cisco 2500 series Wireless Controller
The AP type Cisco AIR-CAP35021-A-K9
I cann't connect the client to AP when i try to connect i get this error on Cisco 2500 series Wireless Controller But the AP get ip .
Please can any on help me .
Client Excluded: MACAddress:Base Radio MAC : Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode:

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12142556/cisco-2500-series-wireless-controller

Oracle RAC and Cisco 7000 Series

Has anyone been successful with database 11.1.0.6 or 11.1.0.7 using a Cisco 7000 series router for the cache fusion interconnect.
A simple yes, if you have done so, will be very much appreciated.
We have a cluster that works with 5000 series switches and hangs with 7000 series ... trying multiple physical switches for the test.
Thank you.

It should work properly. One correction it should be switch not router. We have used the same.

Cisco MDS series switch details

Hello I 'm new to CISCO Switch world.
I 'm working as Clariion Admin and have have taken up the responsibilty to manage switches.Since,i am a novice i need little guidance on how work on cisco switches.I know the Zoning (how zoning done on MDS 9000 series switches) part ,but would like to venture deep into the details on CISCO MDS series switches.
Like, the use of Port channels etc.
Will really appreciate if some one can help me with a link or place ( not the configuration guide) where in i can find details on concentrated more on the theory part .
Thanks in advance!

Actually the best info is in the configuration guides. There are some external companies that run training sessions on the MDS to provide in depth training. There is the MDS cookbook available on CCO that is also a good point of information. If you search on 'MDS white papers' after you login into Cisco.com, there are several good documents that might meet your needs.
Hope this hels,
Mike

Tunneling on cisco 1700 series

Similar Messages

Maybe you are looking for