Turn maximum memory available/user in Solaris OS

As part of the operating system turning for weblogic performance, how to check and turn the maximum memory available for a user process for Sun Solaris 2.6?
Thanks in advance.

It's clear that MathWorks have not updated their software to 64 bits: I'd like them to, (and I have asked them when they will!) but I am wondering if there are limitations that stop me from getting more than about half of the 32 bit memory space.

Similar Messages

What is the available memory for user in iPad

In iPad 3rd generation wifi model, what is the available memory for users?
Capacity          Available Memory
16 GB                      ?
32 GB                      ?

iOS should take about the same amount of storage on both, the difference is partly due to how a 'gigabyte' is defined e.g. on packaging it's 1 billion bytes, but on the device itself it uses the binary definition (2 to the power 30), and some storage may also be 'lost' by formatting : http://support.apple.com/kb/TS2419

How to mount USB & CDROM drives from single user mode - Solaris boot disk?

Hi All,
I need to carry out ufsrestore on a single newly replaced system disk (no redundancy / mirroring) from either USB or CDROM drives from the following steps:
( i ) GRUB => e, e, cdrom –s, Enter, b (boot from Solaris 10 x86 media).
( ii ) Choose menu 1 for Install Solaris Interactive Mode to reach single user mode.Below are the commands that I have tried in single user mode without success:
mount –r –F pcfs /dev/dsk/c1t0d0p0 /cdrom (after unmount Solaris CD)
mount: /dev/dsk/c1t0d0p0 is not a DOS filesystem.
svcadm –v enable smserver
svcadm: Pattern ‘smserver’ doesn’t match any instances
svcadm enable autofs
svcadm: Pattern ‘autofs’ doesn’t match any instances
devfsadm
devfsadm: mkdir failed for /dev 0s1ed: Read-only file system
mkdir /mnt
mkdir: Failed to make directory “/mnt”; Read-only file systemPart of the problem is due to the current READ ONLY filesystems which does not allow the creation of mount point such as /mnt.
I have been able to create both / root (/dev/dsk/c1t0d0s0) and /export/home (/dev/dsk/c1t0d0s0) filesystems with newfs that are awaiting for restore using ufsrestore.
The only option I am left with is to attach a secondary disk to install Solaris 10 on either of them before bring the system to multi-user mode so that service such as volmgt, autofs, volfs are available to access USB & CDROM drives.
Any suggestion on how to resolve this issue?
Many thanks,
Jack

Hi JKGN,
Is the directory a located under the root filesystem. ie /a? Are there any other mount point for say USB drive as well? I am not in a position to try it out right now but will get back
to you soon on whether /a exist or not.
Btw, the last thing I managed to do on this system at the time was added a secondary 1TB internal disk with the intention to restore both / and /export/home data onto this disk while
making use of all the disk device management services such as the following services only available in a fully installed Solaris system (both single & multi-user modes) installed on the
primary disk:
# svcs smserver
STATE          STIME    FMRI
online         Jun_08   svc:/network/rpc/smserver:default
# svcs autofs
STATE          STIME    FMRI
online         Jun_08   svc:/system/filesystem/autofs:default
# devfsadm
# iostat -En
c1t0d0           Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: ATA      Product: SAMSUNG HD321KJ Revision: 0-11 Serial No:
Size: 320.07GB <320072932864 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 41 Predictive Failure Analysis: 0
c0t0d0           Soft Errors: 0 Hard Errors: 5 Transport Errors: 0
Vendor: PHILIPS Product: DVD+-RW DVD8801 Revision: AD21 Serial
Size: 17.54GB <17538875392 bytes>
Media Error: 0 Device Not Ready: 5 No Device: 0 Recoverable: 0
Illegal Request: 10 Predictive Failure Analysis: 0
c2t0d0           Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: JetFlash Product: Transcend 16GB   Revision: 1100 Serial No:
Size: 0.00GB <0 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 7 Predictive Failure Analysis: 0
# rmformat
Looking for devices...
     1. Volmgt Node: /vol/dev/aliases/cdrom0
        Logical Node: /dev/rdsk/c0t0d0s2
        Physical Node: /pci@0,0/pci-ide@1f,1/ide@0/sd@0,0
        Connected Device: PHILIPS DVD+-RW DVD8801 AD21
        Device Type: DVD Reader/WriterHowever, I was disappointed that "iostat -En" has not found the secondary disk (1 TB) even though it was available earlier, for Solaris installation as the only disk on the same system.
As a result, I am left with no option but the need to rebuild this system with only a single primary disk while in single user mode. However, the single user mode that I am in is the
one from Solaris installation disk with restrictive (_cannot create folder for mount point or running disk management utilities_) capability such as those services just covered, compared to one from a completed Solaris installation system with full access to all filesystems and utilities / commands in general.
I would very much value your assistance on how to mount both CD & USB in this restrictive limited Read Only OS (assume that it is running from memory) in order to get complete access to
the blank primary disk so that full restore with ufsrestore could take place.
Thanks in advance,
Jack
Edited by: 797805 on 9/06/2012 04:15

"The Finder does not have enough memory available"

"The Finder does not have enough memory available"
Situation: G4 (AGP Graphics), OS 9.0 with tons of memory.
Problem: Only with any browser viz Explorer, Communicator, iCab or Opera (all versions). Starts off fine. I have broadband. Then steadily goes slower and slower till virtually stops even with just the one browser and one window and no other programs in use. Try to do anything else and above message appears. The problem seems to involves the operating system and the way it interacts with the code of certain sites eg Ebay. It has nothing to do with PRAM, or allocation of memory to the browser or deleting various Preferences. The deletion of Finder, Memory etc Preferences, quitting, restarting all deal with the symptoms and are not a permanent cure. The primary symptom is a massive loss of available memory, not even enough to run a single browser and one window! Any simple solutions? I realise I can upgrade to OS 9.2. Will this work? Apart from this browser problem I am happy with my present set so is there a simpler solution apart from upgrading?

Thankyou to all for the welcome and your responses to my query.
I have 640mb of RAM. The problem is intermitent and is determined to a great extent by the sites which I visit. Yahoo for example is great - no problems. In another window visiting eg Ebay will eventually (variable) cause a slowdown. I have switched Virtual Memory on and off, changed cache, program allocations of memory, regularly used Norton Utilies to inspect, repair, defrag etc and looked all over the place for advice. Things run great for a while but it is only a question of time , months or even days, before the problem re-appears. I was surprised to find so little about it on the Web. Perhaps everyone else has upgraded or is on OS X! If I could have done something without upgrading I may have gone for that option as everything else is running like a dream and I want to keep it that way! I use programs such as Paperport (sadly not made for OS X) which I find a marvellous scanning and paperwork management program. To get it to work with OS 9.0 I had to determine with Cassidy & Green's marvellous extension conflict identifier Conflict Catcher that the Control Strip needed disabling. If I upgrade, I could, for Paperport et al, upset the Apple cart! I have also read about a program called Reaper which was used to deal, I believe, with Finder memory problems with OS 7 and OS 8. It is still available on at http://www.versiontracker.com/dyn/moreinfo/macos/3783 Apart from this I know nothing more at present about it.
However, the following was one item which I found of great interest which goes along with your advice of upgrading.
From http://www.icab.de/faq.html#q36
"Mac OS 8/9: Why does iCab 3.0 complain that it is running out of memory all the time?
This is not a bug of iCab, it's a bug of the "classic" MacOS 8.5/8.6 (and maybe OS 9.0 as well). The problem occurs when a web page has web forms with text input fields. The Unicode text input fields (MLTE) of these old MacOS releases do still have some serious bugs. One of theses bugs causes the MacOS to reserve almost all available memory for these text edit fields so there's no memory left for iCab. Apple has fixed this bug in MacOS 9.2.x (maybe in 9.1 as well), so the best solution for this problem would be to upgrade the MacOS. If this is not possible, you can disable the Unicode text input fields in the preferences dialog of iCab in the panel "Operation > Browser, Tabs". Switch off the option "Use Unicode TextEdit" to configure iCab so that it will use the "ancient" text edit fields, which do work OK, but which do not support Unicode".
Here is someone with a similar problem back in 2000:
"From TacitRF
Date: Thurs, Jun 8 2000 12:00am
Email: [email protected] (TacitR)
Groups: comp.sys.mac.system
This is ridiculous! I have hardly touched this machine today. Does RAM get eaten up while the computer is sitting there idle (and sleeping every now and then after I've checked email or looked at a couple newsgroup posts)?
Yes, it can, under certain circumstances.
Open your TCP/IP control panel. Click the Options button. (If there is no Options button, select Edit->User Mode, and click "Advanced.") Is "Load Only When Needed" turned on? If it is, you may severly fragment the memory in your computer every time you start a program that uses the Internet. Let's say, for example, you launch Netscape. Netscape tries to access the Internet. This causes TCP/IP to load, on top of Netscape. Now, when you quit Netscape, the memory it was using may not get freed up. Launch Outlook. It loads TCP/IP. Now, when you quit Outlook, you may not get its memory back either". Try turning off Load Only When Needed in the TCP/IP Options, see if that solves
the problem. Hope that helps!"
I find that whatever I do one way or another the slowdown will eventually reappear. A bit like weeding gardens and washing dishes! Well unless there is a way of dealing with OS 9.0 memory behaviour with browsers it looks like an upgrade will have to do!
Mac OS 9.0.x

Is there a maximum memory allocated?

Dear all,
Anyone knows if there's a limitation to the maximum memory
that labview can allocate in Win98?
I cannot allocate more than ~ 19500 KB and my computer has
1GB.
Cheers,
Ernest

It seems it is a problem with the working set size and locking of pages. We have developed under Win2000 and have a double buffer daq application. The problem was the application was too late in the loop to get the data from the driver so it gets overwritten. Think of calling AI Read in a loop and the loop stopped for some time.
I suppose you have no documentation for the windows API so I give you some from the MSDN.
VirtualLock is the function which locks memory into RAM.
"The VirtualLock function locks the specified region of the process's virtual address space into physical memory, ensuring that subsequent access to the region will not incur a page fault.
All pages in the specified region must be committed. Memory protected with PAGE_NOACCESS cannot be locked.
Locking pages into memory may degrade the performance of the system by reducing the available RAM and forcing the system to swap out other critical pages to the paging file. Each version of Windows has a limit on the maximum number of pages a process can lock. This limit is intentionally small to avoid severe performance degradation. Applications that need to lock larger numbers of pages must first call the SetProcessWorkingSetSize function to increase their minimum and maximum working set sizes. The maximum number of pages that a process can lock is equal to the number of pages in its minimum working set minus a small overhead.
Pages that a process has locked remain in physical memory until the process unlocks them or terminates.
To unlock a region of locked pages, use the VirtualUnlock function. Locked pages are automatically unlocked when the process terminates."
The SetProcessWorkingSetSize functions allows you to get more locked memory.
"The SetProcessWorkingSetSize function sets the minimum and maximum working set sizes for the specified process.
The working set of a process is the set of memory pages currently visible to the process in physical RAM memory. These pages are resident and available for an application to use without triggering a page fault. The size of the working set of a process is specified in bytes. The minimum and maximum working set sizes affect the virtual memory paging behavior of a process.
The working set of the specified process can be emptied by specifying the value -1 for both the minimum and maximum working set sizes.
If the values of either dwMinimumWorkingSetSize or dwMaximumWorkingSetSize are greater than the process' current working set sizes, the specified process must have the SE_INC_BASE_PRIORITY_NAME privilege. Users in the Administrators and Power Users groups generally have this privilege. For more information about security privileges, see Privileges.
The operating system allocates working set sizes on a first-come, first-served basis. For example, if an application successfully sets 40 megabytes as its minimum working set size on a 64-megabyte system, and a second application requests a 40-megabyte working set size, the operating system denies the second application's request.
Using the SetProcessWorkingSetSize function to set an application's minimum and maximum working set sizes does not guarantee that the requested memory will be reserved, or that it will remain resident at all times. When the application is idle, or a low-memory situation causes a demand for memory, the operating system can reduce the application's working set. An application can use the VirtualLock function to lock ranges of the application's virtual address space in memory; however, that can potentially degrade the performance of the system.
When you increase the working set size of an application, you are taking away physical memory from the rest of the system. This can degrade the performance of other applications and the system as a whole. It can also lead to failures of operations that require physical memory to be present; for example, creating processes, threads, and kernel pool. Thus, you must use the SetProcessWorkingSetSize function carefully. You must always consider the performance of the whole system when you are designing an application."
But these functions will not be supported under Win98. I know from some other function which was stated to be not supported under Win98 were supported under Win98SE.
But thats the time to get an answer from NI personal with more insight into what NIDAQ and the lvdaq.dll does.
Waldemar
Waldemar
Using 7.1.1, 8.5.1, 8.6.1, 2009 on XP and RT
Don't forget to give Kudos to good answers and/or questions

HT204149 What is the maximum resolution available for use with the Apple Mini DisplayPort to Dual-Link DVI adapter?

What is the maximum resolution available for use with the Apple Mini DisplayPort to Dual-Link DVI adapter?

Hey guys,
I found out an answer by myself...
The missing link : the MacBook Pro needs to be powered... as in you need to plug the charger in...
In conclusion, you simply plug everything, turn on the MacBook Pro, close the lid, and there you go !

Amount of Resources CPU and Memory per user

Hi,
We are looking to deploy a Line of Business Application via RemoteApp and a custom template. The application requires a significant amount of RAM and CPU, can someone tell me who much RAM and CPUs are allocated per session \ user? I would expect
that we would use the Standard tier if any difference to resources available.
Thanks
Giles

Hi James,
Currently there is no way to configure resources other than selecting either Basic or Standard. If you would like a lower per-VM user density (and thus higher resources for each user) what you can do is create more collections, and only assign
a small number of users to each.
For example, say you only wanted to have a maximum of 4 users on each VM, providing typically at least 1 vCPU per user. In this case you would create collections with the Basic plan, each linked
to the same template image, and only assign a maximum of 4 user accounts on the user access tab of each. Assuming each user uses 80+ hours a month, the total (before discounts) cost for each collection would be $228/month, making each user
cost about $57/month, slightly less than equivalent cost under Standard plan pricing if you factor in resources per user.
You probably already know this, but I will explain how scaling works normally for others that may read this. Azure RemoteApp will automatically create more VMs for each collection as needed to handle user load (Scale-Out) and shut down VMs when the
user load is reduced (Scale-In). The key thing that affects this scaling mechanism is the maximum concurrent users allowed on each VM, which for Standard is 10.
In your case you are asking if you can have more resources per user, hence my instructions above for creating multiple collections and limiting the number of assigned users to less than 10 each.
Depending on your unique needs it may make more sense to create a custom RDS deployment on Azure IaaS VMs. In this case you could control the size/type of VM used, user density, etc. Downside is you have to set up and manage more
RDS components than you do if you use Azure RemoteApp.
-TP

Please help, my iMac is running slow and plenty of memory available?

Please help, my iMac is running slow and plenty of memory available? I tried reading some of these forums to see what to do, I have already deleted all of my downloads that were stored in the downloads file. Not sure what to do next, I ran the etrecheck and here is the following info from the scan:
EtreCheck version: 2.2 (132)
Report generated 4/20/15, 2:55 PM
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Click the [Click to remove] links for help removing adware.
Hardware Information: ℹ️
    iMac (27-inch, Mid 2011) (Technical Specifications)
    iMac - model: iMac12,2
    1 2.7 GHz Intel Core i5 CPU: 4-core
    4 GB RAM Upgradeable
        BANK 0/DIMM0
            2 GB DDR3 1333 MHz ok
        BANK 1/DIMM0
            2 GB DDR3 1333 MHz ok
        BANK 0/DIMM1
            Empty
        BANK 1/DIMM1
            Empty
    Bluetooth: Old - Handoff/Airdrop2 not supported
    Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
    AMD Radeon HD 6770M - VRAM: 512 MB
        iMac 2560 x 1440
System Software: ℹ️
    OS X 10.10.2 (14C109) - Time since boot: 5:29:18
Disk Information: ℹ️
    ST31000528AS disk0 : (1 TB)
        EFI (disk0s1) <not mounted> : 210 MB
        Macintosh HD (disk0s2) / : 999.35 GB (872.44 GB free)
        Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
    OPTIARC DVD RW AD-5690H
USB Information: ℹ️
    Apple Inc. FaceTime HD Camera (Built-in)
    Apple, Inc. Keyboard Hub
        Apple Inc. Apple Keyboard
    Apple Inc. BRCM2046 Hub
        Apple Inc. Bluetooth USB Host Controller
    Apple Internal Memory Card Reader
    Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
    Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
    Mac App Store and identified developers
Adware: ℹ️
    Genieo, InstallMac Adware! [Click to remove]
    More adware files Adware! [Click to remove]
Problem System Launch Agents: ℹ️
    [killed]    com.apple.CallHistoryPluginHelper.plist
    [killed]    com.apple.CallHistorySyncHelper.plist
    [killed]    com.apple.cloudd.plist
    [killed]    com.apple.cmfsyncagent.plist
    [killed]    com.apple.coreservices.appleid.authentication.plist
    [killed]    com.apple.EscrowSecurityAlert.plist
    [killed]    com.apple.gamed.plist
    [killed]    com.apple.icloud.fmfd.plist
    [killed]    com.apple.Maps.pushdaemon.plist
    [killed]    com.apple.nsurlsessiond.plist
    [killed]    com.apple.printtool.agent.plist
    [killed]    com.apple.scopedbookmarkagent.xpc.plist
    [killed]    com.apple.security.cloudkeychainproxy.plist
    [killed]    com.apple.spindump_agent.plist
    [killed]    com.apple.telephonyutilities.callservicesd.plist
    15 processes killed due to memory pressure
Problem System Launch Daemons: ℹ️
    [killed]    com.apple.ctkd.plist
    [killed]    com.apple.icloud.findmydeviced.plist
    [killed]    com.apple.ifdreader.plist
    [killed]    com.apple.nehelper.plist
    [killed]    com.apple.nsurlsessiond.plist
    [killed]    com.apple.spindump.plist
    [killed]    com.apple.wdhelper.plist
    7 processes killed due to memory pressure
Launch Agents: ℹ️
    [not loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
    [running]    com.adobe.AdobeCreativeCloud.plist [Click for support]
    [running]    com.dced8a8837572b7b.agent.plist [Click for support]
    [loaded]    com.oracle.java.Java-Updater.plist [Click for support]
Launch Daemons: ℹ️
    [loaded]    com.adobe.fpsaud.plist [Click for support]
    [not loaded]    com.dced8a8837572b7b.daemon.plist [Click for support]
    [running]    com.dced8a8837572b7b.helper.plist [Click for support]
    [loaded]    com.microsoft.office.licensing.helper.plist [Click for support]
    [loaded]    com.oracle.java.Helper-Tool.plist [Click for support]
    [loaded]    com.oracle.java.JavaUpdateHelper.plist [Click for support]
User Launch Agents: ℹ️
    [loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
    [loaded]    com.adobe.ARM.[...].plist [Click for support]
    [loaded]    com.adobe.ARM.[...].plist [Click for support]
    [failed]    com.citrixonline.GoToMeeting.G2MUpdate.plist [Click for support] [Click for details]
    [loaded]    com.genieo.completer.download.plist Adware! [Click to remove]
    [loaded]    com.genieo.completer.update.plist Adware! [Click to remove]
    [running]    com.google.Chrome.framework.plist [Click for support]
    [loaded]    com.google.keystone.agent.plist [Click for support]
    [failed]    com.webtools.update.agent.plist [Click for support] [Click for details]
User Login Items: ℹ️
    iTunesHelper    Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
    AdobeResourceSynchronizer    Application (/Applications/Adobe Reader.app/Contents/Support/AdobeResourceSynchronizer.app)
    Dropbox    Application (/Applications/Dropbox.app)
    AdobeResourceSynchronizer    Application Hidden (/Applications/Adobe Acrobat XI Pro/Adobe Acrobat Pro.app/Contents/Support/AdobeResourceSynchronizer.app)
    Google Chrome    Application Hidden (/Applications/Google Chrome.app)
Internet Plug-ins: ℹ️
    Default Browser: Version: 600 - SDK 10.10
    Flip4Mac WMV Plugin: Version: 3.0.0.85 BETA - SDK 10.7 [Click for support]
    AdobeAAMDetect: Version: AdobeAAMDetect 2.0.0.0 - SDK 10.7 [Click for support]
    FlashPlayer-10.6: Version: 17.0.0.169 - SDK 10.6 [Click for support]
    AdobePDFViewerNPAPI: Version: 11.0.10 - SDK 10.6 [Click for support]
    Silverlight: Version: 5.1.30514.0 - SDK 10.6 [Click for support]
    Flash Player: Version: 17.0.0.169 - SDK 10.6 [Click for support]
    QuickTime Plugin: Version: 7.7.3
    iPhotoPhotocast: Version: 7.0
    SharePointBrowserPlugin: Version: 14.4.8 - SDK 10.6 [Click for support]
    AdobePDFViewer: Version: 11.0.10 - SDK 10.6 [Click for support]
    JavaAppletPlugin: Version: Java 8 Update 40 Check version
User internet Plug-ins: ℹ️
    CitrixOnlineWebDeploymentPlugin: Version: 1.0.105 [Click for support]
    Google Earth Web Plug-in: Version: 7.1 [Click for support]
Safari Extensions: ℹ️
    Omnibar Adware! [Click to remove]
    MacMin
3rd Party Preference Panes: ℹ️
    Flash Player [Click for support]
    Flip4Mac WMV [Click for support]
    Java [Click for support]
Time Machine: ℹ️
    Time Machine not configured!
Top Processes by CPU: ℹ️
         3%    AddressBookSourceSync
         3%    Google Chrome Helper(10)
         3%    Google Chrome
         2%    mdworker(5)
         1%    WindowServer
Top Processes by Memory: ℹ️
    729 MB    Google Chrome Helper(10)
    481 MB    kernel_task
    119 MB    Google Chrome
    115 MB    Mail
    74 MB    softwareupdated
Virtual Memory Information: ℹ️
    58 MB    Free RAM
    3.94 GB    Used RAM
    218 MB    Swap Used
Diagnostics Information: ℹ️
    Apr 20, 2015, 09:21:25 AM    Self test - passed

So I looked up the info on OWC as suggested and found the correct memory to upgrade but not sure how much to get and which option? I wanted to know how much space I have available to upgrade so I don't buy something that's more than what can be used. I'm not sure if I need 4GB or 8GB of ram? Also there are two options with every memory choice for instance:
8.0GB PC3-10600 1333MHZ SO Kit (4GB + 4GB) w/Lifetime Limited Warranty
Same Day
$78.79
8.0GB PC3-10600 SO-DIMM 204 Pin w/Lifetime Limited Warranty
Same Day
$82.79
Not sure what the difference is in the two and which I would need to purchase? Thank you for all your help!

Photoshop CS3 "Not enough scratch memory available" error.

Hi,
I am Using Adobe Photoshop CS3 Version 10.0 and I keep getting the error "Not enough Scratch memory available to perform this action" whenever I try to Save a .psd file to a .jpg/.jpeg file.
I did go to Edit -> Preferences -> Performance, and add my other two partitions as scratch disks, also put up my E: drive as the primary scratch disk on the top of the list (Which has 80GB's of space) but I still keep getting this error.
My file (the .psd that i am trying to save to a .jpg) has a total size of 56MB and 300dpi with 4 or 5 layers in it and the target jpg file is supposed to be 12inches by 20inches.
Some other things I have tried is celaring the %temp% folder, Defragmenting my Hard Drive(s), Disk Cleanup, set my System Page file to 4GB, but all this is of no use.
I know that I have enough RAM and Hard disk space so please help me get rid of this problem.
Also, this maybe a stupid question but, does the type of RAM and Processor you are using effect this? I have a DDR RAM.. 2GB, I know its outdated, its our office computer I am working on.. My Processor is a Core 2 Duo which isnt bad.
HELP PLEASE!!!

I think Varun is mistaking one's forums Join Date for a post time stamp.
I'm moving this post from this forum for photoshop-dot-com (an online portal) to the correct forum for Photoshop pro users like yourselves.
FYI, the correct forum URL is: http://forums.adobe.com/community/photoshop
Since you've posted in this forum for Photoshop.com, you may receive additional posts in this forum unless you update your profile. After signing in on these forums, go to Your Stuff > Forums, and disable any forum you don't want to watch.
Kind regards,
Charlie

What's the maximum memory ram for Macbook Pro?

Hello,
May I know what's the maximum memory ram capacity for Macbook Pro?
I am having Macbook Pro - 2.53GHz Intel Core 2 Duo
Thank you!
Alvin

Hate to resurrect a dead horse but....I was looking in the instructions for memory upgrades and the instructions specified that the computer will only recognize 3 gigs. Will that still be in effect if I upgrade to Snow Leopard when it becomes available? Or do I need to save my pennies for a Mac Pro? What I am getting at is: is the reason for the RAM cap due to software issues, 64 bit not being native, different version of leopard used on notebooks, or is it due to hardware issues.

Maximum Memory Size & Memory Size

Will a server's memory automatically increase from Memory Size to Maximum Memory Size as the VM requires it? Or is this only valid for adding memory to the Memory Size value manually?

keithrust wrote:
Will a server's memory automatically increase from Memory Size to Maximum Memory Size as the VM requires it? Or is this only valid for adding memory to the Memory Size value manually?No, there is no automatic increase in memory. The max memory size just specifies the maximum amount to which you can manually adjust the memory of a running VM. I've now taken to setting the max memory size to the total available memory on my Oracle VM Servers, with memory size set to something reasonable. This way, I can adjust right up to the limit of physical memory without rebooting.

Maximum no of users supported by OCS 10.1.2 in a single box installation ?

Hi OCS experts,
What is the maximum number of users supported by OCS 10.1.2 in a single box installation for a 6 way Intel box or a 12way AIX box.???
I mean if the server hardware (processor, memory, and storage are huge enough)...
Are there any limits by the software side of OCS ???
I am planning to deploy OCS for about 15,000 users on Redhat Linux AS 4. We also have the option to deploy it on AIX if required.
Many thanks,
maas.

Many thanks. But as OCS 10.1.2 documentation indicates upto 1,000 users for single server installation. So I wanted to know if there is any practical limit by the OCS software itself on the number of users in single server deployment on Linux.
Like for instance IBM indicates that domino 7 can now go upto 12,000 users in a single box.
Is there any similar recommendation from Oracle to ease in capacity planning decisions for Architects and Implementers.???
I understand that it would be a very difficult prediction keeping in mind the huge functionality of OCS. So let me narrow the scope of our deployment, In the beginning we would using OCS mostly for Email (15,000 users) and about 2000 of these users would also be using calendering. 4,000 Email users use POP clients to check emails frequently. Remaining users use Webmail to check emails upto 2 or 3 times a day.
Now, if you experts advice that a six way IBM eServer X445 server with 16GB RAM and sufficient SAN storage would be able to take this load then I can go ahead with it. Do I have to take any specific measure in design and deployement to leave room for adding nodes.
Many thanks,
maas

The iTunes library file cannot be saved. There is not enough memory available.

For about a week I've been getting this message when I'm listening to music in iTunes (usually in Cover Flow mode). I usually get the message after listening to music about 20+minutes. First the album artwork begins to "white out" or is replaced by a music note pic (like when there is no album artwork data available) and then if I don't shut iTunes down and restart it I will get the "The iTunes library file cannnot...." error message. If I continue to ignore it or click "do not show message again" box, iTunes will eventually stop responding and shut down.
My computer has 77GB of memory available.
I've tried:
- turning off home sharing
- clearing cache
- running virus scan
- made sure there is no memory quota on
Any help would be appreciated!

PROBLEM SOLVED:
I downloaded a corrupted music file. Deleted the file...problem gone!

Insufficient Shared Objects Memory Available

Hi Friends ,
You must be knowing sample application <b>wdr_test_chat</b> .I have used , executed application many time ....now when I run it and click in Log on ...log on pop up come and I am able to enter name ...but on click ok following dump coming....it is not case that there is problem with code as I have run it so many time already....IS that has to do something to my server ?
Dump
The following error text was processed in the system SD8 : Insufficient Shared Objects Memory Available
The error occurred on the application server q4inpusy007_SD8 _01 and in the work process 0 .
The termination type was: RABAX_STATE
The ABAP call stack was:
Method: ATTACHUPDATE70 of program CL_SHM_AREA===================CP
Method: ATTACH_FOR_UPDATE of program CL_WDR_TEST_CHAT_SHM_AREA=====CP
Method: ATTACH_FOR_UPDATE of program CL_WDR_TEST_CHAT_SHM==========CP
Method: LOGIN of program CL_WDR_TEST_CHAT_SHM==========CP
Method: LOGIN of program CL_WDR_TEST_CHAT==============CP
Method: ONACTIONLOGIN of program /1BCWDY/CUHRRK26ZJ7PFHMON3IO==CP
Method: IF_WDR_VIEW_DELEGATE~WD_INVOKE_EVENT_HANDLER of program /1BCWDY/CUHRRK26ZJ7PFHMON3IO==CP
Method: INVOKE_EVENTHANDLER of program CL_WDR_DELEGATING_VIEW========CP
Method: IF_WDR_ACTION~FIRE of program CL_WDR_ACTION=================CP
Method: DO_HANDLE_ACTION_EVENT of program CL_WDR_WINDOW_PHASE_MODEL=====CP

Hi,
I think in case of shared memeory area the system will allocate each area a maximum of 3MB space. so once you use the full memory the system will show you the error message 'Insufficient Shared Objects Memory Available'.
I think this can be avoided by freeing the shared memory area after a certian amount of time.
Regards,
Ajith V

"...There is not enough memory available."

I'm running the most recent version of iTunes. I've got quite a bit of purchased music.
So, I'm coming home from college. Just before I leave, I download and install the newest update. I come home, fire up iTunes, and I am told I need to authorize.
I enter my password in. It works! (I had to deauth all comps first, but the point is I could log in)
Having logged in, I get a new error message:
"We could not complete your Music Store request. There is not enough memory available. There was an error in the Music Store. Please try again later."
I've emailed the iTunes support people and they were basically useless, telling me to make sure I was updated and that I had free authorization slots.
The problem seems similar to this old thread - http://discussions.apple.com/message.jspa?messageID=785786 - but it is locked. And the person didn't mention which cache files he deleted.
Could anyone offer any advice?
Thanks.

Please help...I have the exact same problem...iTunes support is totally useless as well as applecare, they just keep resetting my password. Every time I try to authorize I add another computer to the maximum of five and then I get the too many computers authorized message. Before I reach that point I get the not enough memory message. I am desperate.

Turn maximum memory available/user in Solaris OS

Similar Messages

Maybe you are looking for