Tuxedo ART DB Configuration with XA
Hi,
I am trying to get my tuxedo application to work. I am not so much experienced with Tuxedo as far as database connections.
Basically when I start up the server. Do i need to have a TMSNAME set up? So far the sample_03 application works, but when I startup I do have an error about no TMS_ORA around.
Can someone please let me know what do I need to do to remove this error? I found something like a buildtms utility but after I configured it, my transactoins were not happening.
Please help.
Thanks
Todd Little wrote:
Hi,
OK, a couple of comments. It will help greatly if you can post whatever errors you are getting when you try something. These might be errors from a command such as crdl in tmadmin, or errors seen when you try to boot your application, etc. As well, posting the portion of the ULOG from the period of time when you're having a problem. These will help cut down the time to help you get this resolved.
When you say crdl did not work, what happened? You will not be able to use XA transactions until the transaction log is created.
You asked before about best practices and XA. It's not really so much a question of best practices, it's more a question of whether you need distributed transactions that guarantee consistency, i.e, the ACID properties of a distributed transaction. By using XA, you can ensure that updates to multiple resource managers either all occur or none occur, thus ensuring consistency of your application state. Without XA, if you modify multiple resource managers (multiple databases, a database and a queuing system, etc.) as in withdrawing money from an account in one database and depositing the money in an account in another database, there is no straightforward way to ensure that both updates occur or that neither occur.
Tuxedo is never a resource manager, it is always a transaction manager in XA terminology. Databases, queuing systems, and the like are resource managers.
The only real way to tell if XA is being used is to check with the resource managers and whatever logs they maintain. If XA is involved, then requests to the resource managers will be associated with a global transaction ID (GTRID). If you have TSAM installed, you can use its transaction monitoring category to monitor XA transactions.
Regards,
Todd Little
Oracle Tuxedo Chief ArchitectHi Todd,
Thank your for your response. It turns out that I had all the steps covered as you outlined. There is a setup.sh file in the sample_03 directory which will run the crdrl command.
At this point, I am having some problems running my code, and I am getting an ABEND.
This is the output from my stdout_strn file:
(FLDID(63555132)) 2
(FLDID(63555133)) 2271560481
(FLDID(63555134)) 100
(FLDID(63555135)) 100
(FLDID(63555136)) 0
(FLDID(63555200)) 0
(FLDID(63555201)) 24
(FLDID(63555202)) 80
(FLDID(63555203)) 5
(FLDID(63555212)) 0
(FLDID(63555213)) 0
(FLDID(63555214)) 0
(FLDID(197772865)) TX
(FLDID(197772866))
(FLDID(197772869))
(FLDID(197772912)) 0001501161936009
(FLDID(197772914)) IBM-3279-3-E
(FLDID(197772938)) ibm-37
(FLDID(197772939)) ascii
(FLDID(231327299)) BCTL
(FLDID(231327300)) CIX1
(FLDID(231327315)) ' DBCTL
(FLDID(231327333)) BCTL
(FLDID(231327335)) 000A
(FLDID(231327345))
(FLDID(231327349))
KIX-IERROR - CICS ERROR
KIX-IETRACE - KIX__RECEIVE_MAP____________
EIBFN - '1802' 'RECEIVE MAP '
EIBRESP - '01' 'ERROR '
EIBRESP2 - '00'
EIBCALEN - '+00182'
EIBAID - '9'
EIBTRNID - 'BCTL'
EIBTRMID - '0028'
EIBTASKN - '0022070'
EIBRSRCE - '^@^@^@^@^@^@^@^@'
KIX__USER_ABEND EIBFN =<^X^B>
KIX__USER_ABEND EIBRESP=<+0000000001>
01 : CTLB1 /opt/oracle/art11gR1/Cics_RT/sample/sample_03/CICS/CTLB1.gnt
02 : KIX__USER_ABEND KIX__USER_ABEND
03 : set_err_proc set_err_proc
-----> KixProgramAbort
-----> KixLevelStackFree
And this is the output form my stderr_strn file:
TCP__ReceiveMap : rc <1>
ERROR: receive map BmsTerm[1]
>> tcpstub >> TCP__ReceiveMap - Return length=<0>
tcpstub >> TCP_UpdateEib
tcpstub >> TCP_UpdateEib - EIBAID=<39/'9'>
tcpstub >> TCP_UpdateEib - EIBRESP=<1>
tcpstub >> TCP_UpdateEib - EIBRESP2=<0>
tcpstub >> TCP_UpdateEib - EIBRCODE=< >
tcpstub >> TCP_UpdateEib >> DONE162459 @................ CTLB1 Fatal Cobol error in tpr 'BCTL ': #Load error : file '.ABEND'#error code: 173, pc=0, call=1, seg=0#173 error message text not found
-----> KixProgramReturn(longjump) - STATUS_ABORT
> cobcancel <CTLB1>
tcpstub >> TCP__SendTextFileSelectedRemove (directory:regexp '/tmp':'.*-\[.*]-\[6404]-.*')
FileSelectedRemove (directory:/tmp)
@BCTL 6242 1209673199 1796424903 1209673499 1796454912
I was only running 2 users at a time, and the program is hung.
Similar Messages
-
Tuxedo Art Wb Sample Batch program RSSBBB00 / JCL LODCUST.ksh FAIL
I am in process of executing the RSSBBB00 program using the LODCUST.ksh scripts created by the Tuxedo. I have used ARTJESADMIN / smj command as given below to submit the job.
$ARTJEADMIN
smj -i LODCUST.ksh Job 00000006 is submitted successfully
when used the PTJ command it showed the job status as FAIL.
Checked files and logs from 00000006 but couldnt find any error / issue.
Checked 00000006 -> EXEC -> class, jobname, priority, restart, scriptname and typrun files
00000006 -> LOG and 00000006 -> SYSOUT files are empty.
Can anyone please suggests how to check the error / issues of the failed job.It looks like you might be missing Pro*COBOL libraries, or at least don't have them in the right path. Did you install Oracle DB client on this machine? If it's installed, you should be able to point to the right database path for the client in ART Workbench Configure > Build Options wizard, which would then generate the right makefiles and environment scripts. Also, please check the setenv script under your ../deploy/Batch_RT directory and make sure it has been generated with correct settings for Oracle DB.
-
Urgent Help WorkBench Tuxedo ART, Project BBVA Mexico
Xin Cao, or who can support us.
We are working on a draft Rehosting at BBVA Bancomer Mexico, along with Oracle Mexico through its representative (Javier Soto).
We have studied and analyzed for Tuxedo Art WorkBench converter, but when trying to convert some JCL (JES2) of BBVA that has the following execution utilities:
ACPMAIN
ADRDSSU
ADUUMAIN
AMUUMAIN
ASMA90
DFSRRC00
DMBATCH
DSICMULT
DSICOPY
DSN1COPY
FTP
ICEGENER
ICEMAN
IEV90
IEWL
IGYCRCTL
IKJEFT1A
IKJEFT1B
PASOEXT
PTLDRIVM
WTO
WorkBench sends error (XXXX Utility not supported) and not continuous.
The big question or concern that we have to continue the project is:
Is it possible to include these utilities in the WorkBench?
How would this be possible?
Or we would have to develop?
What can we do to not check WorkBench error and continue with the conversion?
Should we modify your program WorkBench (pob) to include new utilities?
How can we accomplish this?
This is the big question to continue this great project.
Greetings.Some of these utilities are supported in the latest version (11.1.1.2.1 GA'd end of July), or can be replaced with supported utilities. What version of ART Workbench and Runtime are you using? You can connect with me directly for Tuxedo ART-related questions/help at [email protected]
-
I have copied the make file provided along with the Tuxedo ART samples onto the demo directory. But when I do a make usage in the samples directory(Fig.1) it works. Where as it doesnt work in the directory, where I have copied.(Fig.2). Kindly help to fix this error.
Fig.1
[root@SJP2VM0140 source]# pwd
/home/user/oracle/art_wb11gR1/samples/STDB2ORA/source
[root@SJP2VM0140 source]# ls
BATCH CICS COPY DDL JCL makefile MAP
[root@SJP2VM0140 source]# make usage
============ Help usage =============================
This makefile process all or selected files for R4Z ..
Extentions of Files names available :
.pob : Result of parsing (Under the directory pob of the component)
.cdm : Result of parsing without rules, generated automaticly by the parser
.shrec : Result of parsing without rules, generated automaticly by the parser
Fig 2
[root@SJP2VM0140 source]# pwd
/opt/Tuxedo/KIXEDO/TUXDEMO/source
[root@SJP2VM0140 source]# ls
BATCH Cobol-dump-map.pob JCL MAP symtab-TUXDEMO.pob
CICS COPY makefile Reports-TUXDEMO
[root@SJP2VM0140 source]# make usageHi,
possibilities:
1. missing bos.adtm.libm (not installed), so missing /usr/lib/libm.a
2. missing /bin from PATH
Herald ten Dam
http://htendam.wordpress.com -
i changed my sim on my iPhone n reconfigured iMessage, it configured with my number but when i sign in with my apple id it says username/password is wrong while in all other things like FaceTime, App Store it worked with the same id and password..
can anyone help me to solve this issuei just opened my ipad, started my apple account/I.D. and realized I put the wrong e mail. I was having trouble correcting my I.D on the Ipad so I went to my laptop and make the proper changes/slash e mail address I wanted for my apple ID. I got back to my ipad and try to download an app I can't because I have to sign in my apple account and I can't because it still has the irrelivant I.D/email address..
So, i did what you said.. went to setting>app store> tapped on my e mail.. it asked me to sign in (with my invalid emails address showing). I signed in with the password I had created. It said "incorrect".. I went to reset password. I reset password, tried to sign in and it says again "unvalid password".. this is getting irritating. I have been asking and no one knows what to do. -
I have a problem with Mail on my Macbook Pro. It is configurated with a gmail account, and now I can't access the mail. Is it possible to reboot the account or..? Please help:)
The question mark means the computer cannot find a bootable volumes so can;t do anything, That, combined with annoying sounds, strongly suggests a failed hard drive.
You can ask a "genius" at an Apple Rtail Store to test it but I'm pretty sure the drive is kaput. I'm hoping you had your data backed up. -
I wonder if it is possible to use 1 Computer (Macbook Pro)
- configured with 2 (ore even more) user accounts (i.e. me + my kid)
- and each user account has a different Apple-ID (account) for iTunes purchases & iTunes authorization ?
I woud think that is fine in terms of the underlying license agreement refereing to re-download purchased movies, shows, apps, etc.
However, it seams that there is that miraculous 90 days restriction, which I don't understand, and which allows me only to "authorise" the Computer under one or the other account. The switch is unfortunatelly only possible every 90 days ?!?
Thanks anybody for help
OliverThe 90 day association doesn't stop you authorising an account, it only stops you from using another account for iTunes Match or automatic downloads or redownloading its past purchases : http://support.apple.com/kb/HT4627
There are a few methods listed on this page for how you could do it e.g. multiple user acounts, same iTunes but you having separate playlists, separate iTunes libraries : http://support.apple.com/kb/HT1495 -
Hi All,
I am facing the below error while installing Oracle RAC in Silent Mode.
SEVERE: There are no common subnets represented by network interfaces across all cluster nodes.
SEVERE: [FATAL] [INS-40925] One or more nodes have interfaces not configured with a subnet that is common across all cluster nodes.
CAUSE: Not all nodes have network interfaces that are configured on subnets that are common to all nodes in the cluster.
ACTION: Ensure all cluster nodes have a public interface defined with the same subnet accessible by all nodes in the cluster.
My /etc/hosts is given below.
127.0.0.1 localhost localhost.localdomain
#Public
192.168.1.101 rac1 rac1.localdomain
192.168.1.102 rac2 rac2.localdomain
#Private
192.168.2.101 rac1-priv rac1-priv.localdomain
192.168.2.102 rac2-priv rac2-priv.localdomain
#Virtual
192.168.1.103 rac1-vip rac1-vip.localdomain
192.168.1.104 rac2-vip rac2-vip.localdomain
#SCAN
192.168.1.105 rac-scan rac-scan.localdomain
Could you please help me to get rid of the error INS-40925....Any Idea...???Hi Ramesh,
Please find the result of ifconfig -a from both nodes RAC1 & RAC2.
ifconfig -a in RAC1
[oracle@rac1 Desktop]$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 08:00:27:17:7A:D5
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe17:7ad5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:102 errors:0 dropped:0 overruns:0 frame:0
TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:25472 (24.8 KiB) TX bytes:3322 (3.2 KiB)
Interrupt:19 Base address:0xd020
eth1 Link encap:Ethernet HWaddr 08:00:27:C0:AC:DB
inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fec0:acdb/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:240 (240.0 b) TX bytes:816 (816.0 b)
Interrupt:16 Base address:0xd240
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:56 errors:0 dropped:0 overruns:0 frame:0
TX packets:56 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:6394 (6.2 KiB) TX bytes:6394 (6.2 KiB)
virbr0 Link encap:Ethernet HWaddr 52:54:00:CC:BD:FB
inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
virbr0-nic Link encap:Ethernet HWaddr 52:54:00:CC:BD:FB
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
ifconfig -a in RAC2
[oracle@rac2 Desktop]$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 08:00:27:C9:38:82
inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fec9:3882/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:122 errors:0 dropped:0 overruns:0 frame:0
TX packets:59 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:32617 (31.8 KiB) TX bytes:5157 (5.0 KiB)
Interrupt:19 Base address:0xd020
eth1 Link encap:Ethernet HWaddr 08:00:27:90:B5:A0
inet addr:192.168.2.102 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe90:b5a0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:11 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:240 (240.0 b) TX bytes:746 (746.0 b)
Interrupt:16 Base address:0xd240
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:56 errors:0 dropped:0 overruns:0 frame:0
TX packets:56 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:6390 (6.2 KiB) TX bytes:6390 (6.2 KiB)
virbr0 Link encap:Ethernet HWaddr 52:54:00:CC:BD:FB
inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
virbr0-nic Link encap:Ethernet HWaddr 52:54:00:CC:BD:FB
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) -
Error in Proxy configuration with SLM
> Hello Experts,
>
> I am encountring some problems when configuring SLM with Solution Manager 7.01 SP06. I have applied all the settings required for SLM and described on the How-To documentation. I have also read all the forums regarding this issue, but nothing helpful. This issue is the configuration of the proxy settings. We are using SNC for our Saprouter, so I assume that I have to use also the sapserv3 for SLM configuration, with the port 8080.
>
> I have added also these entries on Web Service Container in VA:
> Proxy Host: sapserv3
> Proxy Port: 8080
> Exclude List: myhost.mydomain
> And Save
>
> When I execute the configuration check with the transaction "/n/tmwflow/mopzcfg", I have these errors:
>
> <description>Check Proxy settings for download</description>
> + <config-path>
> <entry>Configuration path: SDT/SDT|cod-zeus|PS1/SDTExecutionService/DOWNLOAD</entry>
> </config-path>
> - <input>
> <entry>Proxy use: true</entry>
> <entry>Proxy host: sapserv3</entry>
> <entry>Proxy port: 8080</entry>
> <entry>Use proxy authentication: false</entry>
> <entry>Check HTTP connection to: http://www.sap.com/index.epx</entry>
> </input>
> - <output>
> <entry>Test Result: FAILED</entry>
> </output>
>- <error>
>- <MESSAGE>
> <ID>java.net.UnknownHostException: BAEx.Failed</ID>
> <CREATOR>SLM: java.net.PlainSocketImpl: Line: 201</CREATOR>
> <TEXT>www.sap.com</TEXT>
> </MESSAGE>
> </error>
> </CheckResult>
> - <CheckResult status="FAILED">
> <description>Check Proxy settings for web services</description>
> - <config-path>
> <entry>Configuration path: WebServicessAddOn/HTTPProxy</entry>
> </config-path>
> - <input>
> <entry>Proxy use: true</entry>
> <entry>Proxy host: sapserv3</entry>
> <entry>Proxy port: 8080</entry>
> <entry>Check HTTP connection to: http://www.sap.com/index.epx</entry>
> <entry>Set Proxy-Authorization</entry>
> </input>
> - <output>
> <entry>Proxy user:</entry>
> <entry>Test Result: FAILED</entry>
> </output>
>- <error>
>- <MESSAGE>
> <ID>java.net.UnknownHostException: BAEx.Failed</ID>
> <CREATOR>SLM: java.net.PlainSocketImpl: Line: 201</CREATOR>
> <TEXT>www.sap.com</TEXT>
> </MESSAGE>
> </error>
> </CheckResult>
> - <CheckResult status="FAILED">
> <description>Check SMP user and SP web service</description>
>
> Configuration path: SDT/SDT|host|sid/SDTExecutionService/DOWNLOAD
>
> please tell me what should I do. Thank you
Edited by: sapmoo on May 7, 2010 11:59 AMis Done...
I have changed the 8001 Port, by 50100... :S
this is my First Client with both instances in a same Server than I have to use this port... always I have used 800 + number of Instance...
Regards -
Hello,
our customer plans to use a Non-SAP solution for variant configuration (Camos) in SAP ERP (ECC 6.0) and in SAP CRM 7.0 EHP1 as well.
ERP sales orders (and ERP quotations) should be created in SAP CRM (CRM WebUI).
Is it possible to use variant configuration (with an external variant configuration tool) when creating ERP sales orders and quotations in the SAP CRM WebUI or do we have to implement SAP IPC for this?
Thanks in advance.
Regards,
AEVDear AEV,
I think LORD (lean orders) should work with variant configuration as well. In the note 1236015 there is not restriction listed. However you need lord2 activated in ECC, and ECC system should be on EHP4.
Best regards
Rene -
When I try to reformat there is an error message about configurations with the pointing device
When I try to reformat there is an error message about configurations with the pointing device
I am not sure I am on the correct section in the support area for Lenovo.
I had a mouse issue. It was unable to read the mouse. Now the mouse is working and it is initialized.
I have no idea why.
There is an error message saying that I should press F 1or F2. I pressed down F 1 and I tried to work with it and I enabled the mouse or I tried. The mouse is working fine but the computer will not recover completely the way it used to.
It is very confusing. When I shut down and restart there is an message that was not there before about the pointing device. Also the recovering operation never asked me for disks. Now it is doing that. I have disks but this is all confusing. I just want the computer to be the way it was. It is working fine except for booting up and the messages.Hi marissa, welcome to the forums,
you may or may not be in the right place, but it would certainly help members to help you if you could post exactly which Lenovo system; notebook / computer, you have and which operating system is installed on it.
Thanks in advance
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog -
Senario:
Need to manage 500 Enterprise iPads
Requirements;
1) Trackable via Find my iOS device (we have 500 iPads and with the 100 device limit per iCloud account for Find my iOS device limit we have 5+ iCloud accounts).
2) Individually named iPads for locating and sending commands to wipe, lost mode, etc.. on map per Find my iOS device (we uniquely name them in Apple Configurator either by using the "sequensetially numbering feature", or by creating individual back ups (yes, 450) with the name specified in the image).
3) Find my iOS device feature enabled in base Prepared or Supervised image (using one of our 5+ iCloud accounts) (image can be created during prepared stage, or in supervised stage) - tried both and have the same issue - which I am getting to...
4) VPP codes for paid apps (all VPP codes purchased with generic account which is the Apple Admin account for VPP purchases). Apple Configurator is set up under a different/ unique Apple account (i.e. not VPP admin account) and not logged into iTunes for any purchases/ services).
Issue: Can not do any following senarios;
A)
1) configure master iOS 7 iPad with iCloud account with Find my iOS feature enabled in Prepare stage (added during preparing stage)
2) configure master iOS 7 iPad with iCloud account with Find my iOS feature enabled in Supervised stage (added after supervising, and then backing up that supervised and iOS Find my iOS device enabled)
B) 1) Apply master image to any Supervised iPad (under senario step A) or senario step B)), including the (Supervised or/ Prepared iPad that was used to create the maset iOS 7 image
Result = fail with Apple generic code "4" ; This is obviously due to Find my iOS device feature enabled during image capture.
According to Apple (see Apple Config. Help) the 'Activation lock' (new feature in iOS 7) will not be enabled on a supervised device when an iCloud account with "Find my iDevice" is enabled. Their "help files" seem to imply after the device is Supervised, and a person (presumably and end user) adds thier own iCloud account with Find my iOS device enabled the activation lock is not enabled and erasing/ reconfiguring with Apple Configurator will not cause reimaging probhlems such as requiring the end user's credentials to reconfigure the device using Apple Configurator (i.e. you won't need the end user's credentials).
Needed: To be able to configure Supervised iPads with iCloud account (Enterprised owned iCloud account) configured on the basse image, which has Find my iOS device enabled, and to be able to apply that base image to all Enterprise iPads without generic apple error code 4 issue.Hi all
I am trying to replicate these steps in my environment but I am having trouble getting an iCloud backup restored to a supervised device. Can someone clarify the steps? The parts I am unsure on are:
1) Do you Prepare in Configurator with all the institution owned apps? Or do you install them after restoring the iCloud backup?
2) After entering the personal AppleID to restore the iCloud backup, the setup wizard prompts for the Institution/Configurator AppleID, there is an option to 'Skip Now'. Do you enter in the password for the institution account? or do you skip that step?
3) What exactly is on the screen in the 'mini setup assistant' after the restore when you Refresh with Configurator?
Any help would be greatly appreciated! -
IPhone mail configured with Gmail alternate address
I'm really stuck.. I have a Gmail account (through Google Apps for Business) that I have configured with Mail on my iPhone using Exchange to connect the account. Everything has been working flawlessly, until my employer made a change to our email addresses, so that we had to set up a new domain alias through Gmail as our "send from" account.
My problem is that I can't for the life of me figure out how to send from this new address from my iPhone.
Finally, I found a post on the web that seems to explain a way to do this, using the OTHER account setup (IMAP) on the iPhone (instead of either Gmail or Exchange): http://modernerd.com/post/535350679/solved-gmail-ipad-iphone-and-multiple-from That seemed to do the trick, except then I realized I would no longer have Push email, which I have really come to rely on.
I tried using the native iPhone Gmail app for a few days, as that seemed to be the only solution, but there's just so many things about that app that really make me miss my good 'ol Apple mail.
Any other creative solutions out there? Thanks for any advice!yeah, it used to work fine because google was supported exchange on mobile devices up until the end of february or so. they let everyone keep their settings the way they were unless they changed them or deleted them, so that's totally expected. The thing with the push is that gmail no longer seems to be supporting that behavior through native apps on mobile devices because it's something they want their exchange customers to pay for
-
Problem With Cutom Configuration with Object Type
Dear Guru's
I am working WebUI, I am facing a problem with Custom Configuration.
1. The initial requirement to control the visibility for a dropdown event in ERP Quotation.
2. To this i copied the default configuration to custom configuration with custom Object type and Subtype.
CONFIG KEY: ZPJQTN
OBJECT TYPE: ZOTYP_CONFIG
OBJECT SUB TYPE: ZSTYPE_CONFIG1
3. I have created customm fields in enhancement.
4. Now i chosen my new configuration (ZPJQTN,ZOTYP_CONFIG,ZSTYP_CONFIG1), when i click Show available fields, the custom fields are not showing. Instead the created fields are available at other configuration.
5. I am able to control the visibility for the standard available fields.But i am not getting the custom created fields
(Note: I have created the Object type and Object sub type as follows: SPRO->CRM->UI Framework->Define Object Types
Object type: ZOTYP_CONFIG Callback class: ZCL_CONFIG_CALLBACK
Redifned the method: IF_BSP_DLC_OBJ_TYPE_CALLBACK~GET_OBJECT_SUB_TYPES
Coded as below:
data: lv_subtype type bsp_dlc_object_sub_type.
lv_subtype = 'ZSTYP_CONFIG1'.
append lv_subtype to result.
lv_subtype = 'ZSTYP_CONFIG2'.
APPEND lv_subtype to result.
Now Please suggest me how to achieve this.
Also please let me know, whether i am following the correct procedure for controlling the visibility.
Thanks in Advance,
S.Meganadhan.Hi Harshit,
I added custom fields using AET only.
I am able to see the field got added in the structure. I am able to access GET and SET methods of the field.
But the problem is, it is not getting saved. Am i missed any configuration step?
Please suggest me.
Thanks in advance,
Regards,
S.Meganadhan. -
BPM 11g install and configuration with Webcenter
Hi,
I am new to this BPM so need some help in installation. Where can I download the latest version of BPM 11g and for installating it what steps do I need to follow. Also I need to integrate Webcenter also so for webcenter integration what do I need to install and configure with BPM 11g.
Do I need to install webcenter full suite for integration with BPM and if so can I install both BPM and webcenter in one home iteself. Where can I find some documentation arround installing BPM and configuring with Webcenter.
ThanksHi,
Need some info on the install I have to install both SOA BPM 11g 11.1.1.3 and Webcenter 11.1.1.3 on the same box. I have installed the SOA BPM 11.1.1.3 but wanted to find out what is the best option of installing Webcenter 11.1.1.3 as I need to integrat SOA BPM 11g 11.1.1.3 and Webcenter 11.1.1.3. Here is what I think are the options but don't know which one should I go for or is there any other option but the fact is I need to install both on the same box.
*1. Should I install Webcenter in a separate HOME in doing so I will end up installing weblogic again and then install webcenter. Will endup having two ORACLE HOMES one for SOA BPM and one for Webcenter.*
*2. OR should I install Webcenter in the same home as SOA BPM and create a new domain in doing so what happens to some of the components that are installed when installing SOA BPM.*
*3. OR should I just extend the SOA BPM Domain and have both SOA BPM and Webcenter installed in the same domain. I believe this will only add the webcenter components but don't know if there are any issues.*
And help is really appreciated..
Thanks
Maybe you are looking for
-
MSI Big Bang XPower II - Firewire and PCI issues
Hi all, yesterday i recieved my new MSI Big Bang XPower II and got some really strange issues: First of all ill let you know my hardware: MSI Big Bang XPower II (BIOS v1.4) new Intel I7 Extreme 3960X new G.SKILL 64GB RAM Kit 1600 new Palit NVIDIA GTX
-
HP 15.6" G56-129WM Laptop PC with Intel Celeron 900 Processor & Windows 7 Home Premium
My computer is really slow... I've tried restarting it to the manufuture setting, but it didn't really work . It is a bit faster but its still really slow. It runs slow even when just having one google chrome/ internet experor site. What could the p
-
How to make list item multi select
Hi all, I'm suing Oracle 10g and I want to make a TList multi-selectable and then how I can return the selected records Thanks in advance :)
-
The screen to my ipod touch has gone completely white and I cannot power it down, or do anything. I have it plugged into a power source right now
-
N86 - media player Bug ?
Hi, while my media player is on pause, after receiving a call and closing it, then media player start playing. Is it a bug or it can be solve with settings?