Two beeps when an incoming call gets connected

Since a couple of weeks ago I started hearing 2 beeps when an incoming call gets connected.
I can only hear these 2 beeps when I use my headset (original iphone headset) to answer the call. I hear these 2 sounds right after I answer the call and then I can hear the person on the other side of the line.
This does not happen for outgoing calls. The person on the other side of the line can't hear the beeps. I tried this in another iPhone and I couldn't hear the beeps either.
Does anybody knows why?
Please, serious answers (I'm tired of listening about the bighbrother thing)

Hi there,
Did you ever figure out what those beeps are? I'm hearing them too.
Thanks!

Similar Messages

Analog line (FXO) Incoming calls getting connected after 3 rings

     HI,
we are having 4 Analog line (FXO)...Every time when callers call the number they hear 3 rings & after that call frwds to AA or any extension.
In show voice port summary, we can see that voice port is getting connect at the first ring but after 3 rings only phone rings.
here is the o/p of voice port.
Foreign Exchange Office 0/0/0 Slot is 0, Sub-unit is 0, Port is 0
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 128 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is plar
Connection Number is 250
Initial Time Out is set to 15 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Power Denial Disconnect Time Out is set to 1000 ms
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for AE
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Caller ID Info Follows:
Standard BELLCORE
Caller ID is received after 1 ring(s)
Translation profile (Incoming): INCOMING_CallerID_PROFILE
Translation profile (Outgoing):
lpcor (Incoming):
lpcor (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is signal
Answer Supervision is inactive
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimum ring duration timer is 125 ms
Hookflash-in Timing is set to 600 ms
Hookflash-out Timing is set to 400 ms
Supervisory Disconnect Timing (loopStart only) is set to 350 ms
OPX Ring Wait Timing is set to 6000 ms
Secondary dialtone is disabled

hostname VGUAE001
no aaa new-model
clock timezone UAE 4 0
ip cef
ip domain name yourdomain.com
no ipv6 cef
multilink bundle-name authenticated
trunk group ALL_FXO
max-retry 5
voice-class cause-code 1
hunt-scheme longest-idle
translation-profile outgoing PROFILE_ALL_FXO
voice-card 0
voice call send-alert
voice rtp send-recv
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
voice class cause-code 1
no-circuit
voice translation-rule 1112
rule 1 /^9/ //
voice translation-rule 3265
rule 1 // /9\1/
voice translation-profile INCOMING_CallerID_PROFILE
translate calling 50
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
license udi pid CISCO2901/K9 sn FCZ173992Z8
hw-module pvdm 0/0
hw-module pvdm 0/1
username cisco privilege 15 secret 4 opjnnkXqCr4kCOa9DuALcNpBOMetBAc/usnpSWADsCI
username godiva privilege 15 secret 4 cH8b8z.ioYu/pMv/AKuEcBd/f6g9v/vm/s3aXeqUAd6
redundancy
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address 192.168.31.2 255.255.255.0
ip helper-address 192.168.31.11
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr 192.168.31.2
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip http path flash:
ip route 0.0.0.0 0.0.0.0 192.168.31.1
control-plane
voice-port 0/0/0
trunk-group ALL_FXO 64
translation-profile incoming INCOMING_CallerID_PROFILE
groundstart auto-tip
cptone AE
connection plar opx 222
caller-id enable
voice-port 0/0/1
trunk-group ALL_FXO 64
translation-profile incoming INCOMING_CallerID_PROFILE
cptone AE
connection plar opx 222
caller-id enable
voice-port 0/0/2
trunk-group ALL_FXO 64
translation-profile incoming INCOMING_CallerID_PROFILE
cptone AE
connection plar opx 222
caller-id enable
voice-port 0/0/3
trunk-group ALL_FXO 64
translation-profile incoming INCOMING_CallerID_PROFILE
cptone AE
connection plar opx 250
caller-id enable
mgcp profile default
dial-peer voice 2000 voip
destination-pattern 2..
session target ipv4:192.168.31.11
incoming called-number .
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
dial-peer voice 10 pots
trunkgroup ALL_FXO
description **CCA*UAE*Fire**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 997
forward-digits all
no sip-register
dial-peer voice 11 pots
trunkgroup ALL_FXO
description **CCA*UAE*International Numbers**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 900T
forward-digits all
no sip-register
dial-peer voice 12 pots
trunkgroup ALL_FXO
description **CCA*UAE*Eitisalat**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 9101
forward-digits all
no sip-register
dial-peer voice 13 pots
trunkgroup ALL_FXO
description **CCA*UAE*Water or electrical emergencies**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 971
forward-digits all
no sip-register
dial-peer voice 14 pots
trunkgroup ALL_FXO
description **CCA*UAE*Police and emergencies**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 999
forward-digits all
no sip-register
dial-peer voice 15 pots
trunkgroup ALL_FXO
description **CCA*UAE*National area codes**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 9[1-579].......
forward-digits all
no sip-register
dial-peer voice 16 pots
trunkgroup ALL_FXO
description **CCA*UAE*Mobile Numbers**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 90[5-6][0-7].......
forward-digits all
no sip-register
dial-peer voice 17 pots
trunkgroup ALL_FXO
description **CCA*UAE*toll-free**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 9[2-9]00T
forward-digits all
no sip-register
dial-peer voice 18 pots
trunkgroup ALL_FXO
description **CCA*UAE*Fixed Line Numbers**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 9[2-8]T
forward-digits all
no sip-register
dial-peer voice 19 pots
trunkgroup ALL_FXO
description **CCA*UAE*808**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 5
destination-pattern 9808T
forward-digits all
no sip-register
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/0/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/0/1
dial-peer voice 52 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/0/2
dial-peer voice 53 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/0/3
dial-peer voice 54 pots
description ** FXO pots dial-peer **
destination-pattern A0
port 0/0/0
no sip-register
dial-peer voice 55 pots
description ** FXO pots dial-peer **
destination-pattern A1
port 0/0/1
no sip-register
dial-peer voice 56 pots
description ** FXO pots dial-peer **
destination-pattern A2
port 0/0/2
no sip-register
dial-peer voice 57 pots
description ** FXO pots dial-peer **
destination-pattern A3
port 0/0/3
no sip-register
Debug vpm signal:
Nov 23 19:31:31.556: htsp_process_event: [0/0/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
Nov 23 19:31:31.556: htsp_timer - 125 msec
Nov 23 19:31:31.684: htsp_process_event: [0/0/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
Nov 23 19:31:31.684: htsp_timer - 10000 msec
Nov 23 19:31:31.684: htsp_timer3 - 5600 msec
Nov 23 19:31:31.684: [0/0/0] htsp_start_caller_id_rx:Mode BELLCORE. Alerting 0x1
Nov 23 19:31:31.684: htsp_start_caller_id_rx create dsp_stream_manager
Nov 23 19:31:31.684: [0/0/0] htsp_dsm_create_success returns 1
Nov 23 19:31:33.604: htsp_process_event: [0/0/0, FXOLS_RINGING, E_DSP_SIG_0100]
Nov 23 19:31:33.604: fxols_ringing_not
Nov 23 19:31:33.604: htsp_timer_stop
Nov 23 19:31:33.604: htsp_timer - 10000 msec
Nov 23 19:31:37.284: htsp_process_event: [0/0/0, FXOLS_RINGING, E_HTSP_EVENT_TIMER3]fxols_snoop_clid_stop
Nov 23 19:31:37.284: htsp_timer_stop3
Nov 23 19:31:37.516: htsp_process_event: [0/0/0, FXOLS_RINGING, E_DSP_SIG_0000]
Nov 23 19:31:39.604: htsp_process_event: [0/0/0, FXOLS_RINGING, E_DSP_SIG_0100]
Nov 23 19:31:39.604: fxols_ringing_not
Nov 23 19:31:39.604: htsp_timer_stop
Nov 23 19:31:39.604: htsp_timer_stop3
Nov 23 19:31:39.604: [0/0/0] htsp_stop_caller_id_rx. message length 0htsp_setup_ind
Nov 23 19:31:39.604: [0/0/0] get_fxo_caller_id:Caller ID receive failed. parseCallerIDString:no data.
Nov 23 19:31:39.604: [0/0/0] get_local_station_id calling num= calling name= calling time=11/23 23:31 orig called=
Nov 23 19:31:39.604: //-1/B583C95F8093/CCAPI/cc_api_display_ie_subfields:
   cc_api_call_setup_ind_common:
   cisco-username=
   ----- ccCallInfo IE subfields -----
   cisco-ani=
   cisco-anitype=0
   cisco-aniplan=0
   cisco-anipi=0
   cisco-anisi=0
   dest=250
   cisco-desttype=0
   cisco-destplan=0
   cisco-rdie=FFFFFFFF
   cisco-rdn=
   cisco-rdntype=0
   cisco-rdnplan=0
   cisco-rdnpi=0
   cisco-rdnsi=0
   cisco-redirectreason=0   fwd_final_type =0
   final_redirectNumber =
   hunt_group_timeout =0
Nov 23 19:31:39.604: //-1/B583C95F8093/CCAPI/cc_api_call_setup_ind_common:
   Interface=0x3CE27724, Call Info(
   Calling Number=,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=250(TON=Unknown, NPI=Unknown),
   Calling Translated=FALSE, Subscriber Type Str=RegularLine, FinalDestinationFlag=TRUE,
   Incoming Dial-peer=50, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), Calling IE Present=FALSE,
   Source Trkgrp Route Label=ALL_FXO, Target Trkgrp Route Label=, CLID Transparent=FALSE), Call Id=-1
Nov 23 19:31:39.604: //-1/B583C95F8093/CCAPI/ccCheckClipClir:
   In: Calling Number=(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed)
Nov 23 19:31:39.604: //-1/B583C95F8093/CCAPI/ccCheckClipClir:
   Out: Calling Number=(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed)
Nov 23 19:31:39.604: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
Nov 23 19:31:39.604: :cc_get_feature_vsa malloc success
Nov 23 19:31:39.604: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
Nov 23 19:31:39.604: cc_get_feature_vsa count is 1
Nov 23 19:31:39.604: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
Nov 23 19:31:39.604: :FEATURE_VSA attributes are: feature_name:0,feature_time:1025218944,feature_id:83
Nov 23 19:31:39.604: //83/B583C95F8093/CCAPI/cc_api_call_setup_ind_common:
   Set Up Event Sent;
   Call Info(Calling Number=(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=250(TON=Unknown, NPI=Unknown))
Nov 23 19:31:39.608: [0/0/0] htsp_dsm_close_done
Nov 23 19:31:39.608: htsp_process_event: [0/0/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
Nov 23 19:31:39.608: fxols_wait_setup_ack:
Nov 23 19:31:39.608: [0/0/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
Nov 23 19:31:39.608: //83/B583C95F8093/CCAPI/cc_process_call_setup_ind:
   Event=0x22ACD828
Nov 23 19:31:39.608: //-1/xxxxxxxxxxxx/CCAPI/cc_setupind_match_search:
   Try with the demoted called number 250
Nov 23 19:31:39.608: //83/B583C95F8093/CCAPI/ccCallSetContext:
   Context=0x230F9C10
Nov 23 19:31:39.608: //83/B583C95F8093/CCAPI/cc_process_call_setup_ind:
   >>>>CCAPI handed cid 83 with tag 50 to app "_ManagedAppProcess_Default"
Nov 23 19:31:39.608: //83/B583C95F8093/CCAPI/ccCallProceeding:
   Progress Indication=NULL(0)
Nov 23 19:31:39.608: //83/B583C95F8093/CCAPI/ccCallSetupRequest:
   Destination=, Calling IE Present=FALSE, Mode=0,
   Outgoing Dial-peer=2000, Params=0x230FB0D0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3)
Nov 23 19:31:39.608: //83/B583C95F8093/CCAPI/ccCheckClipClir:
   In: Calling Number=(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed)
Nov 23 19:31:39.608: //83/B583C95F8093/CCAPI/ccCheckClipClir:
   Out: Calling Number=(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed)
Nov 23 19:31:39.608: //83/B583C95F8093/CCAPI/ccCallSetupRequest:
   Destination Pattern=2.., Called Number=250, Digit Strip=FALSE
Nov 23 19:31:39.608: //83/B583C95F8093/CCAPI/ccCallSetupRequest:
   Calling Number=(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=250(TON=Unknown, NPI=Unknown),
   Redirect Number=, Display Info=
   Account Number=, Final Destination Flag=TRUE,
   Guid=B583C95F-53AC-11E3-8093-C8EEBDE4256A, Outgoing Dial-peer=2000
Nov 23 19:31:39.612: //83/B583C95F8093/CCAPI/cc_api_display_ie_subfields:
   ccCallSetupRequest:
   cisco-username=
   ----- ccCallInfo IE subfields -----
   cisco-ani=
   cisco-anitype=0
   cisco-aniplan=0
   cisco-anipi=0
   cisco-anisi=0
   dest=250
   cisco-desttype=0
   cisco-destplan=0
   cisco-rdie=FFFFFFFF
   cisco-rdn=
   cisco-rdntype=0
   cisco-rdnplan=0
   cisco-rdnpi=0
   cisco-rdnsi=0
   cisco-redirectreason=0   fwd_final_type =0
   final_redirectNumber =
   hunt_group_timeout =0
Nov 23 19:31:39.612: //83/B583C95F8093/CCAPI/ccIFCallSetupRequestPrivate:
   Interface=0x22847B14, Interface Type=1, Destination=, Mode=0x0,
   Call Params(Calling Number=,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=250(TON=Unknown, NPI=Unknown), Calling Translated=FALSE,
   Subscriber Type Str=RegularLine, FinalDestinationFlag=TRUE, Outgoing Dial-peer=2000, Call Count On=FALSE,
   Source Trkgrp Route Label=ALL_FXO, Target Trkgrp Route Label=, tg_label_flag=1, Application Call Id=)
Nov 23 19:31:39.612: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
Nov 23 19:31:39.612: :cc_get_feature_vsa malloc success
Nov 23 19:31:39.612: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
Nov 23 19:31:39.612: cc_get_feature_vsa count is 2
Nov 23 19:31:39.612: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
Nov 23 19:31:39.612: :FEATURE_VSA attributes are: feature_name:0,feature_time:1025218720,feature_id:84
Nov 23 19:31:39.612: //84/B583C95F8093/CCAPI/ccIFCallSetupRequestPrivate:
   SPI Call Setup Request Is Success; Interface Type=1, FlowMode=1
Nov 23 19:31:39.612: //84/B583C95F8093/CCAPI/ccCallSetContext:
   Context=0x230FB080
Nov 23 19:31:39.612: //83/B583C95F8093/CCAPI/ccSaveDialpeerTag:
   Outgoing Dial-peer=2000
Nov 23 19:31:39.612: htsp_process_event: [0/0/0, FXOLS_PROCEEDING, E_HTSP_PROCEEDING]fxols_offhook_proc
Nov 23 19:31:39.612: htsp_timer - 120000 msec
Nov 23 19:31:39.612: //84/B583C95F8093/CCAPI/ccGetMediaClassTag:
   media class tag 0
Nov 23 19:31:39.612: //84/B583C95F8093/CCAPI/ccSetMediaclassIp2ipTags:
   media class tags set: NR 0, ASP 0
Nov 23 19:31:39.612: //83/B583C95F8093/CCAPI/ccSetMediaclassIp2ipTags:
   media class tags set: NR 0, ASP 0
Nov 23 19:31:39.612: //84/B583C95F8093/CCAPI/ccGet_xc_nr_asp_info:
   media class tags: NR 0, ASP 0
Nov 23 19:31:39.612: //83/B583C95F8093/CCAPI/ccGet_xc_nr_asp_info:
   media class tags: NR 0, ASP 0
Nov 23 19:31:39.620: //84/B583C95F8093/CCAPI/cc_api_set_called_ccm_detected:
   CallInfo(called ccm detected=TRUE ccmVersion 3)
Nov 23 19:31:39.620: //84/B583C95F8093/CCAPI/cc_api_call_proceeding:
   Interface=0x22847B14, Progress Indication=NULL(0)
Nov 23 19:31:39.628: //84/B583C95F8093/CCAPI/cc_api_set_called_ccm_detected:
   CallInfo(called ccm detected=TRUE ccmVersion 3)
Nov 23 19:31:39.628: //84/B583C95F8093/CCAPI/cc_api_set_delay_xport:
   CallInfo(delay xport=TRUE)
Nov 23 19:31:39.628: //84/B583C95F8093/CCAPI/cc_api_call_alert:
   Interface=0x22847B14, Progress Indication=NULL(0), Signal Indication=SIGNAL RINGBACK(1)
Nov 23 19:31:39.628: //84/B583C95F8093/CCAPI/cc_api_call_alert:
   Call Entry(Retry Count=0, Responsed=TRUE)
Nov 23 19:31:39.628: //83/B583C95F8093/CCAPI/ccCallAlert:
   Progress Indication=NULL(0), Signal Indication=SIGNAL RINGBACK(1)
Nov 23 19:31:39.628: //83/B583C95F8093/CCAPI/ccCallAlert:
   Call Entry(Responsed=TRUE, Alert Sent=TRUE)htsp_alert_notify
Nov 23 19:31:39.628: htsp_process_event: [0/0/0, FXOLS_PROCEEDING, E_HTSP_ALERT]fxols_offhook_alert
Nov 23 19:31:39.628: //84/B583C95F8093/CCAPI/cc_api_set_called_ccm_detected:
   CallInfo(called ccm detected=TRUE ccmVersion 3)
Nov 23 19:31:39.628: //84/B583C95F8093/CCAPI/cc_api_call_notify:
   Data Bitmask=0x5, Interface=0x22847B14, Call Id=84
Nov 23 19:31:39.628: //84/B583C95F8093/CCAPI/cc_api_get_ssCTreRoutingNotSupported:
   CallInfo(ssCTreRoutingNotSupported=FALSE)
Nov 23 19:31:39.628: //84/B583C95F8093/CCAPI/cc_api_get_ccm_detected:
   CallInfo(ccm detected=TRUE)
Nov 23 19:31:39.628: //83/B583C95F8093/CCAPI/ccCallNotify:
   Data Bitmask=0x5, Call Id=83htsp_call_service_msghtsp_call_service_msg not EFXS (2)
Nov 23 19:31:39.672: //84/B583C95F8093/CCAPI/ccIsInfoRingback:
   Returning dpRingBack=0
Nov 23 19:31:39.700: //84/B583C95F8093/CCAPI/cc_api_call_connected:
   Interface=0x22847B14, Data Bitmask=0x1, Progress Indication=NULL(0),
   Connection Handle=0
Nov 23 19:31:39.700: //84/B583C95F8093/CCAPI/cc_api_call_connected:
   Call Entry(Connected=TRUE, Responsed=TRUE, Retry Count=0)
Nov 23 19:31:39.700: //84/B583C95F8093/CCAPI/cc_api_set_called_ccm_detected:
   CallInfo(called ccm detected=TRUE ccmVersion 3)
Nov 23 19:31:39.700: //84/B583C95F8093/CCAPI/cc_api_call_notify:
   Data Bitmask=0x7, Interface=0x22847B14, Call Id=84
Nov 23 19:31:39.700: //83/B583C95F8093/CCAPI/ccGenerateToneInfo:
   Stop Tone On Digit=FALSE, Tone=Null,
   Tone Direction=Network, Params=0x0, Call Id=83
Nov 23 19:31:39.700: //83/B583C95F8093/CCAPI/ccConferenceCreate:
   (confID=0xFFFFFFFF, callID1=0x53, gcid=B583C95F-53AC11E3-8093C8EE-BDE4256A, tag=0x0)
Nov 23 19:31:39.700: //84/B583C95F8093/CCAPI/ccConferenceCreate:
   (confID=0xFFFFFFFF, callID2=0x54, gcid=B583C95F-53AC11E3-8093C8EE-BDE4256A, tag=0x0)
Nov 23 19:31:39.700: //83/B583C95F8093/CCAPI/ccConferenceCreate:
   Conference Id=0xFFFFFFFF, Call Id1=83, Call Id2=84, Tag=0x0
Nov 23 19:31:39.700: htsp_call_bridged invoked
Nov 23 19:31:39.700: //83/B583C95F8093/CCAPI/cc_api_bridge_done:
   Conference Id=0x21, Source Interface=0x3CE27724, Source Call Id=83,
   Destination Call Id=84, Disposition=0x0, Tag=0xFFFFFFFF
Nov 23 19:31:39.700: //84/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
Nov 23 19:31:39.700: cc_api_get_xcode_stream : 4819
Nov 23 19:31:39.700: //84/B583C95F8093/CCAPI/cc_api_bridge_done:
   Conference Id=0x21, Source Interface=0x22847B14, Source Call Id=84,
   Destination Call Id=83, Disposition=0x0, Tag=0x0
Nov 23 19:31:39.700: //83/B583C95F8093/CCAPI/cc_generic_bridge_done:
   Conference Id=0x21, Source Interface=0x22847B14, Source Call Id=84,
   Destination Call Id=83, Disposition=0x0, Tag=0x0
Nov 23 19:31:39.700: //83/B583C95F8093/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0x21, Destination Call Id=84)
Nov 23 19:31:39.700: //84/B583C95F8093/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0x21, Destination Call Id=83)
Nov 23 19:31:39.700: //83/B583C95F8093/CCAPI/ccConferenceCreate:
Nov 23 19:31:39.700: confID:0x21; callEntry1 callID1:0x53, type:6; callEntry2 callID2:0x54, type:1
Nov 23 19:31:39.700: //83/B583C95F8093/CCAPI/cc_api_caps_ind:
   Destination Interface=0x22847B14, Destination Call Id=84, Source Call Id=83,
   Caps(Codec=0x1, Fax Rate=0x1, Fax Version:=0, Vad=0x1,
   Modem=0x2, Codec Bytes=20, Signal Type=3)
Nov 23 19:31:39.700: //83/B583C95F8093/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=1000(ms), Fax Nom=300(ms))
Nov 23 19:31:39.700: //84/B583C95F8093/CCAPI/cc_api_get_ssCTreRoutingNotSupported:
   CallInfo(ssCTreRoutingNotSupported=FALSE)
Nov 23 19:31:39.704: //84/B583C95F8093/CCAPI/cc_api_get_ccm_detected:
   CallInfo(ccm detected=TRUE)
Nov 23 19:31:39.704: //83/B583C95F8093/CCAPI/ccCallNotify:
   Data Bitmask=0x7, Call Id=83htsp_call_service_msghtsp_call_service_msg not EFXS (2)
Nov 23 19:31:39.704: //83/B583C95F8093/CCAPI/cc_process_notify_bridge_done:
   Conference Id=0x21, Call Id1=83, Call Id2=84
Nov 23 19:31:39.704: //84/B583C95F8093/CCAPI/cc_api_caps_ind:
   Destination Interface=0x3CE27724, Destination Call Id=83, Source Call Id=84,
   Caps(Codec=0x1, Fax Rate=0x2, Fax Version:=0, Vad=0x1,
   Modem=0x0, Codec Bytes=160, Signal Type=2)
Nov 23 19:31:39.704: //84/B583C95F8093/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=1000(ms), Fax Nom=300(ms))
Nov 23 19:31:39.704: //84/B583C95F8093/CCAPI/cc_api_caps_ack:
   Destination Interface=0x3CE27724, Destination Call Id=83, Source Call Id=84,
   Caps(Codec=g711ulaw(0x1), Fax Rate=FAX_RATE_VOICE(0x2), Fax Version:=0, Vad=OFF(0x1),
   Modem=OFF(0x0), Codec Bytes=160, Signal Type=2, Seq Num Start=9438)
Nov 23 19:31:39.704: //83/B583C95F8093/CCAPI/cc_api_caps_ack:
   Destination Interface=0x22847B14, Destination Call Id=84, Source Call Id=83,
   Caps(Codec=g711ulaw(0x1), Fax Rate=FAX_RATE_VOICE(0x2), Fax Version:=0, Vad=OFF(0x1),
   Modem=OFF(0x0), Codec Bytes=160, Signal Type=2, Seq Num Start=9438)
Nov 23 19:31:39.704: //83/B583C95F8093/CCAPI/ccCallConnect:
   Progress Indication=NULL(0), Data Bitmask=0x1
Nov 23 19:31:39.704: //83/B583C95F8093/CCAPI/ccCallConnect:
   Call Entry(Connected=TRUE, Responsed=TRUE)
Nov 23 19:31:39.704: htsp_process_event: [0/0/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
Nov 23 19:31:39.704: htsp_timer_stop
Nov 23 19:31:39.704: //83/B583C95F8093/CCAPI/cc_api_voice_mode_event:
   Call Id=83
Nov 23 19:31:39.704: //83/B583C95F8093/CCAPI/cc_api_voice_mode_event:
   Call Entry(Context=0x230F9C10)
Nov 23 19:31:39.704: htsp_process_event: [0/0/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
Nov 23 19:31:39.932: htsp_process_event: [0/0/0, FXOLS_CONNECT, E_DSP_SIG_0110]fxols_rvs_battery
Nov 23 19:31:39.932: htsp_timer_stop2
Nov 23 19:31:39.932: htsp_timer_stop2
Nov 23 19:31:48.860: //84/B583C95F8093/CCAPI/cc_api_call_disconnected:
   Cause Value=16, Interface=0x22847B14, Call Id=84
Nov 23 19:31:48.860: //84/B583C95F8093/CCAPI/cc_api_call_disconnected:
   Call Entry(Responsed=TRUE, Cause Value=16, Retry Count=0)
Nov 23 19:31:48.860: //83/B583C95F8093/CCAPI/ccConferenceDestroy:
   Conference Id=0x21, Tag=0x0
Nov 23 19:31:48.860: //83/B583C95F8093/CCAPI/ccConferenceDestroy:
Nov 23 19:31:48.860: confID:0x21; callEntry1 callID1:0x53, type:6; callEntry2 callID2:0x54, type:1
Nov 23 19:31:48.860: //83/B583C95F8093/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0x21, Source Interface=0x3CE27724, Source Call Id=83,
   Destination Call Id=84, Disposition=0x0, Tag=0x0
Nov 23 19:31:48.860: //84/B583C95F8093/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0x21, Source Interface=0x22847B14, Source Call Id=84,
   Destination Call Id=83, Disposition=0x0, Tag=0x0
Nov 23 19:31:48.860: //83/B583C95F8093/CCAPI/cc_generic_bridge_done:
   Conference Id=0x21, Source Interface=0x22847B14, Source Call Id=84,
   Destination Call Id=83, Disposition=0x0, Tag=0x0
Nov 23 19:31:48.864: //83/B583C95F8093/CCAPI/ccCallDisconnect:
   Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
Nov 23 19:31:48.864: //83/B583C95F8093/CCAPI/ccCallDisconnect:
   Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
Nov 23 19:31:48.864: //83/B583C95F8093/CCAPI/cc_api_get_transfer_info:
   Transfer Number=NULL
Nov 23 19:31:48.864: //84/B583C95F8093/CCAPI/ccCallDisconnect:
   Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=16)
Nov 23 19:31:48.864: //84/B583C95F8093/CCAPI/ccCallDisconnect:
   Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
Nov 23 19:31:48.864: //84/B583C95F8093/CCAPI/cc_api_get_transfer_info:
   Transfer Number=NULL
Nov 23 19:31:48.864: htsp_timer_stop3
Nov 23 19:31:48.872: //84/B583C95F8093/CCAPI/cc_api_get_transfer_info:
   Transfer Number=NULL
Nov 23 19:31:48.872: //84/B583C95F8093/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x22847B14, Tag=0x0, Call Id=84,
   Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
Nov 23 19:31:48.872: //84/B583C95F8093/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
Nov 23 19:31:48.876: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
Nov 23 19:31:48.876: :cc_free_feature_vsa freeing 3D1B9898
Nov 23 19:31:48.876: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
Nov 23 19:31:48.876: vsacount in free is 1
Nov 23 19:31:48.884: htsp_process_event: [0/0/0, FXOLS_CONNECT, E_HTSP_RELEASE_REQ]fxols_offhook_release
Nov 23 19:31:48.884: htsp_timer_stop
Nov 23 19:31:48.884: htsp_timer_stop2
Nov 23 19:31:48.884: htsp_timer_stop3
Nov 23 19:31:48.884: [0/0/0] set signal state = 0x4 timestamp = 0
Nov 23 19:31:48.884: htsp_timer - 2000 msec
Nov 23 19:31:48.884: //83/B583C95F8093/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x3CE27724, Tag=0x0, Call Id=83,
   Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
Nov 23 19:31:48.884: //83/B583C95F8093/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
Nov 23 19:31:48.884: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
Nov 23 19:31:48.884: :cc_free_feature_vsa freeing 3D1B9978
Nov 23 19:31:48.884: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
Nov 23 19:31:48.884: vsacount in free is 0
Nov 23 19:31:49.156: htsp_process_event: [0/0/0, FXOLS_GUARD_OUT, E_DSP_SIG_0110]
Nov 23 19:31:50.884: htsp_process_event: [0/0/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
Nov 23 19:31:50.884: htsp_process_event: [0/0/0, FXOLS_ONHOOK, E_DSP_SIG_0100]

Why does my iPhone 4s beep when answering incoming calls or placing an outgoing call? How do I turn it off?

Starting today my iPhone 4s now beeps when I am making an outgoing call or when I receive an incoming call. I am wondering if this is due to the recent upgrade to 7.0.4. My phone is on Verizon. Does anyone know how to turn this beep off?

This is a new feature of iOS 8 ... go to your iPhone's FaceTime settings and turn off "iPhone Cellular Calls".

Hi, this is amit from india. just started using iphone 4s. i am observing that when an incoming call comes, the phone smtimes shows two virtual buttons of red and green color so as to attend or reject the call. but smtimes it just shows green button. why?

Hi, this is amit from india. just started using iphone 4s. i am observing that when an incoming call comes, the phone smtimes shows two virtual buttons of red and green color so as to attend or reject the call. but smtimes it just shows green button with a slider to attend the call and there is no red button to reject the call. is it a bug or some setting?

Because it behaves differently depending on whether the phone is locked (in standby) or unlocked (in use) when the call comes in.

On IPhone 5S, when making cell calls, it connects to FaceTime.

On IPhone 5S, IOS 7.1.2, when making cell calls, it connects to FaceTime.

Hey there siteshop,
It sounds like you are still hearing the phone line ringing even after the person you call answers the line. I would try the troubleshooting outlined in this article:
iPhone: Troubleshooting issues making or receiving calls
https://support.apple.com/kb/TS3406
Toggle airplane mode: Tap Settings > Enable Airplane Mode, wait five seconds, then turn off airplane mode.
Ensure that your software is up to date:
Check for a carrier settings update.
Check for an iOS software update.
Note: Some updates may require a Wi-Fi connection.
If the iPhone has a SIM card, reseat the SIM card.
If the iPhone 4 or iPhone 4s is on the Verizon network, dial *228 from the iPhone and select option 2 to update the Preferred Roaming List (PRL). The PRL determines the cellular towers the phone uses for cellular service, selecting those with the best signal strength.
Reset the network settings: Tap Settings > General > Reset > Reset Network Settings.
Try to make or receive calls in another location.
Attempt to isolate to one network band:
If you're having the issue on LTE, disable LTE, if possible, and try again.
If you're having the issue on 3G/4G, disable 3G/4G, if possible, and try again.
Contact the carrier to check the following:
Your account is properly configured to use the specific iPhone that has the issue.
There are no localized service outages.
Your account doesn't have a billing-related block.
Your calls don't have errors on the carrier system.
Restore the phone as new.
If the above steps don't resolve the issue, go to an Apple Retail Store, carrier, Apple Authorized Reseller, or contact AppleCare to send the phone in for service.
Thank you for using Apple Support Communities.
All the very best,
Sterling

IPhone 4 - my phone doesn't "ring"... Speaker plays, it works on vibrate, and when you set the ringer, it will play. Just not when an incoming call comes in. Any thoughts?

iPhone 4 - my phone doesn't "ring". Speaker plays, it works on vibrate, and when you set the ringer, it will play. Just not when an incoming call comes in. Any thoughts?

Check the position of the mute switch. On the side, just above the volume keys.

I have iPhone 5s. when an incoming call on the screen iPhone I see a small photo, how can I make a big photo for an incoming call?? I have installed iOS 7.1.1

I have iPhone 5s. when an incoming call on the screen iPhone I see a small photo, how can I make a great big photo for an incoming call?? I have installed ios 7.1.1

Sorry, you can't. Design change with iOS 7.0. Tell Apple you don't like this here:
http://www.apple.com/feedback/iphone.html

HT204380 FaceTime connects ok but rings out when sending call. But no sound when receiving incoming call have checked all the settings and sounds any suggestions

FaceTime connects ok and rings out when sending call but no ringing sound when receiving incoming calls

Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
http://tinyurl.com/a7odey8
Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/TS4268
Using FaceTime and iMessage behind a firewall
http://support.apple.com/kb/HT4245
iOS: About Messages
http://support.apple.com/kb/HT3529
Set up iMessage
http://www.apple.com/ca/ios/messages/
Troubleshooting Messages
http://support.apple.com/kb/TS2755
Setting Up Multiple iOS Devices for iMessage and Facetime
http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
FaceTime and iMessage not accepting Apple ID password
http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
Unable to use FaceTime and iMessage with my apple ID
https://discussions.apple.com/thread/4649373?tstart=90
My Facetime Doesn't Ring
https://discussions.apple.com/message/19087457
For non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
How to Send SMS from iPad
http://www.iskysoft.com/apple-ipad/send-sms-from-ipad.html
 Cheers, Tom

Agent Desktop Error When receive Incoming Call

Hi, I have CAD Ver 8.5.1.39 | CUCM Ver 8.5.1.10000-26 | UCCX Ver 8.5.1.10000-37 running on my network now.
there some problem occurs when I put an Agent into the Line Group with Top Down Distribution call(actualy all the Distribution call type face the same problem).
1. When the Agent Receive Incoming Call from outside(PSTN) sometimes the CAD don't Show Up and show no response but the CIPC work normaly. showed in Not Responded.jpg
2. When the Agent Receive Call and it is show up. I can't answer the call. When I press ctrl-A or i push the answer icon i got the error message show in error.jpg , sometimes when i want to make a call the same problem happens
3. When the Agent Pop Up and the caller end the Call before I can answer. The call got stuck in Agent and Agent cannot make a call. Agent must logout and login again to fix this problem, show on the stuck.jpg
4. When the problem 3 occurs and if the Agent don't fix this problem, the stack got more caller. show in stuck2.jpg
I dont know why this happen, all the call come from outside(PSTN). when I test call from internal the problem doesn't occur.
Please help me. Any help will be helpful
Thank you for your help and participation
Regards,
Yopie.

Hi,
I have an auto attendant, for example like this:
Welcome to the XYZ Company,
Press 1 for purchasing (10 Agent)
Press 2 for Consult (5 Agent)
Or press 0 for operator help (3 Agent)
When the consumer press 1, I want the call distribute to 10 Agent in the Purchasing team.
To make scenario like this I use the hunt pilot and to use hunt pilot i must have line group first.
So I need to put the 10 Agent into the Line Group.
Thanks.

Contact picture does not appear when receiving incoming call

I have attached pictures on my iPhone contacts but when i receive an incoming call the picture does not appear. Any ideas how to resolve.

I am expriencing the same issue with my iPhone 4S, were you able to resolve the problem?

IPhone 3G OS 4.0.1 Reboots when answering incoming calls

I have a 16 GB 3G. Several times since my upgrade to iOS 4 my phone reboots when I swipe to answer an incoming call. I swipe the screen goes blank then the Apple logo appears.
Mark

I have a 3G iphone and have had the same problem and it even has done it on clicking on calendar and other apps. Also the common problem expressed by many regarding horrible slow response time. O/S 4 has been a huge mistake in my opinion for the 3G Iphone.

Issue when receiving incoming calls

Hi,
I have been experiencing the same problem for several months. Sometimes (hopefully it remains rare), when I have an incoming call, my iPhone rings but the screen won't turn on, so that I won't be able to answer the call. The only thing I can do then is to silence the call. Has someone experience the same issue ?

i had it in 1.1.3 but after the update to 1.1.4 didnt have it again (only had it a few times before thought).
i think when i reset the phone (hold home and sleep/wake button) it stopped but i cannot remember for sure
try that, make sure your running 1.1.4, if that doesnt work try a restore and then after that go to an apple store
-matt

Beep when AC adapter plug is connected - can not find on ThinkPad w530

In the opposite to some other users (say in this topic here) I always liked this cool feature of ThinkPad to informed the user with a happy loud beep sound, whether the status of power has really changed after the AC adapter was connected to the laptop. It saves me plenty of times from problems with empty battery and loosing my data at my previous ThinkPads.
So when I've got my new ThinkPad w530 it was one of the first things I've tried to configure to enable these sound notifications. But I am not able to find, how to do it The Manual of the Power Manager states very clearly when explaining Power Management Options, the following:
"Beep when power state changes
When this checkbox is selected, you hear beeps when the computer:
Enters standby mode.
Resumes operation from standby mode.
Enters hibernation mode.
Resumes operation after being in hibernation mode.
Is connected to or disconnected from the AC adapter.".
It seems the thinh I was looked for, but the problem is, that there is no such option at Power Manager Options tab. I've reviewed all other tabs/windows of the app as well, but can not find anything about beep sound.
Have I missed anything? Where this option might actually locate?
Thanks for any ideas!

Unfortunately it's not an option offered on the *30 systems' BIOS, it was removed. Please see the following thread;
http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T530-does-not-make-typical-ThinkPad-Power-S...
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Show dial pad when answering incoming call

I need to be able to press '1' after I answer an incoming call (Google Voice call screening). The dial pad doesn't appear on the screen. If anyone has solved this problem, I'd be grateful to hear how you did.

format the phone. make sure all users from contact list have set their default number. this helped in my case.
Message Edited by damiri on 30-Aug-2009 10:04 PM

Incoming calls get stripped of leading zeros and I don't know why...

Hi,
our UC560 setup is now running for quite some time. But there is still this one issue that is bugging for some time now.
We have two ISDN DID trunks for Incoming / Outgoing calls.
After my very basic setup I noticed that all caller IDs get their leading zero stripped. In Germany we use the "0" as first digit of the area-code and "00" as the international code.
I thought a quick fix would be to just add a Call-Back Rule within CCA to add a leading 0. This works for national calls as the transmitted caller-id always includes the area-code even for local calls.
However If I receive an international call (what happens quite often recently) I'm not getting the expected "00" in front of the number but also only a single "0".
I took a look at all translation-rules that are configured, but I couldn't find any rule that just deletes all leading zeros from the incoming number :( What's happening there?
voice translation-rule 4
rule 1 /301/ /55555529/
rule 2 /302/ /55555529/
rule 13 /^2$..$$/ /5555552\1/
rule 14 /^1$..$$/ /5555551\1/
rule 15 /^.*$/ /+49895555550/
voice translation-rule 5
rule 15 /^...$/ /123456/
voice translation-rule 7
rule 1 /555555201/ /201/
rule 2 /555555202/ /202/
rule 3 /555555203/ /203/
rule 4 /555555204/ /204/
rule 5 /555555205/ /205/
rule 6 /555555206/ /206/
rule 7 /555555207/ /207/
rule 8 /555555208/ /208/
rule 9 /555555209/ /209/
voice translation-rule 8
rule 1 /555555210/ /210/
rule 2 /555555211/ /211/
rule 3 /555555212/ /212/
rule 4 /555555213/ /213/
rule 5 /555555214/ /214/
rule 6 /555555215/ /215/
rule 7 /555555216/ /216/
rule 8 /555555217/ /217/
rule 9 /555555218/ /218/
rule 10 /555555219/ /219/
voice translation-rule 9
rule 1 /555555220/ /220/
rule 2 /555555221/ /221/
rule 3 /555555222/ /222/
rule 4 /555555223/ /223/
rule 5 /555555224/ /224/
rule 6 /555555225/ /225/
rule 7 /555555226/ /226/
rule 8 /555555227/ /227/
rule 9 /555555228/ /228/
rule 10 /555555229/ /229/
voice translation-rule 10
rule 1 /55555529/ /511/
voice translation-rule 12
rule 1 /55555504/ /112/
voice translation-rule 13
rule 1 /555555260/ /996/
voice translation-rule 14
rule 1 /55555501/ /444/
voice translation-rule 15
rule 1 /55555502/ /111/
voice translation-rule 18
rule 1 /555555200/ /444/
voice translation-rule 19
rule 1 /555555100/ /444/
voice translation-rule 20
rule 1 /55555500/ /444/
voice translation-rule 21
rule 1 /5555550/ /444/
voice translation-rule 23
rule 1 /555555110/ /110/
rule 2 /555555111/ /111/
rule 3 /555555112/ /112/
rule 4 /555555113/ /113/
rule 5 /555555114/ /114/
rule 6 /555555115/ /115/
rule 7 /555555116/ /116/
rule 8 /555555117/ /117/
rule 9 /555555118/ /118/
rule 10 /555555119/ /119/
voice translation-rule 24
rule 1 /555555120/ /120/
rule 2 /555555121/ /121/
rule 3 /555555122/ /122/
rule 4 /555555123/ /123/
rule 5 /555555124/ /124/
rule 6 /555555125/ /125/
rule 7 /555555126/ /126/
rule 8 /555555127/ /127/
rule 9 /555555128/ /128/
rule 10 /555555129/ /129/
voice translation-rule 25
rule 1 /555555130/ /130/
rule 2 /555555131/ /131/
rule 3 /555555132/ /132/
rule 4 /555555133/ /133/
rule 5 /555555134/ /134/
rule 6 /555555135/ /135/
rule 7 /555555136/ /136/
rule 8 /555555137/ /137/
rule 9 /555555138/ /138/
rule 10 /555555139/ /139/
voice translation-rule 26
rule 1 /555555140/ /140/
rule 2 /555555141/ /141/
rule 3 /555555142/ /142/
rule 4 /555555143/ /143/
rule 5 /555555144/ /144/
rule 6 /555555145/ /145/
rule 7 /555555146/ /146/
rule 8 /555555147/ /147/
rule 9 /555555148/ /148/
rule 10 /555555149/ /149/
voice translation-rule 27
rule 1 /555555150/ /150/
rule 2 /555555151/ /151/
rule 3 /555555152/ /152/
rule 4 /555555153/ /153/
rule 5 /555555154/ /154/
rule 6 /555555155/ /155/
rule 7 /555555156/ /156/
rule 8 /555555157/ /157/
rule 9 /555555158/ /158/
rule 10 /555555159/ /159/
voice translation-rule 28
rule 1 /555555160/ /160/
rule 2 /555555161/ /161/
rule 3 /555555162/ /162/
rule 4 /555555163/ /163/
rule 5 /555555164/ /164/
rule 6 /555555165/ /165/
rule 7 /555555166/ /166/
rule 8 /555555167/ /167/
rule 9 /555555168/ /168/
rule 10 /555555169/ /169/
voice translation-rule 29
rule 1 /555555170/ /170/
rule 2 /555555171/ /171/
rule 3 /555555172/ /172/
rule 4 /555555173/ /173/
rule 5 /555555174/ /174/
rule 6 /555555175/ /175/
rule 7 /555555176/ /176/
rule 8 /555555177/ /177/
rule 9 /555555178/ /178/
rule 10 /555555179/ /179/
voice translation-rule 30
rule 1 /555555180/ /180/
rule 2 /555555181/ /181/
rule 3 /555555182/ /182/
rule 4 /555555183/ /183/
rule 5 /555555184/ /184/
rule 6 /555555185/ /185/
rule 7 /555555186/ /186/
rule 8 /555555187/ /187/
rule 9 /555555188/ /188/
rule 10 /555555189/ /189/
voice translation-rule 31
rule 1 /555555190/ /190/
rule 2 /555555191/ /191/
rule 3 /555555192/ /192/
rule 4 /555555193/ /193/
rule 5 /555555194/ /194/
rule 6 /555555195/ /195/
rule 7 /555555196/ /196/
rule 8 /555555197/ /197/
rule 9 /555555198/ /198/
rule 10 /555555199/ /199/
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1112
rule 1 /^8/ //
voice translation-rule 2001
voice translation-rule 2002
rule 1 /^6/ //
rule 2 /^A/ //
voice translation-rule 2222
regards,
Fabian

I already figured it out myself - that was easy, if you know where to look...
voice translation-rule 3265
rule 1 /$^.*$$/ /0\1/ type national national
rule 2 /$^.*$$/ /00\1/ type international international

Two beeps when an incoming call gets connected

Similar Messages

Maybe you are looking for