Two Communication Server in the same Server ?

Hi All,
do you know which are the steps and recommendations to install TWO Communication Station in the same server (Windows 2003) ?
The first one is connect to CRM develop system, and the second one to the CRM Quality System.
Regards,
Davide
[email protected]

Hello Davide,
Note 503340 is not valid for 5.0 and above but its major points are still true:
1. Only one default destination can be setup in the DCOM Connector
which is used by the mobile clients after the installation.
2. Only one default COM4ABAP instance can be setup on the
communication station. This COM4ABAP instance is started
automatically after reboot.
DCOM Connector is now .NET Connector and COM4ABAP is now NET4ABAP in 5.0 and higher.
Clearly, connecting to TWO (or more) CRM system has two parts:
a.) For Data Transfer with Conntrans. You can configure A SINGLE COMMSTATION INSTANCE to communicate with MULTIPLE destinations by just adding destinations in the QmtCnfg tool on the CommStation. You can then specify this Commstation and the destination value as you created in the QmtConfg tool on the client and data transfer will work.
b.) For changing passwords of Employees in Tx: SMOEAC. This uses the NET4ABAP service running on the CommStation which is called by the CRM Server. There can be ONLY ONE NET4ABAP service running on a CommStation and this connects to ONLY ONE CRM SYSTEM at a time. Hence it is not possible for one NET4ABAP service to serve multiple CRM systems.
If you need both a and b, it is not possible. If you need only a, it is possible and detailed above and also in the CommStation installation guide.
I also believe you have a message running with SAP Support on this same issue and you would have gotten the same details from them.
Best Regards,
Ankan

Similar Messages

How Can I create a cluster of two instances running on the same server?

Hello,
I can't find how to create a cluster or even a failover rule for my two instances running on the same server ODSEE 11gR1.
Could you please help?
Thanks,

Hello,
Clustering (intended as Sun Cluster, Veritas Cluster, etc... ) IS NOT SUPPORTED since 7.0:
http://docs.oracle.com/cd/E20295_01/pdf/821-1216.pdf [page 20]
and, based on my own experience, is the WORST way of achieving high availability of an LDAP Directory Service and an almost GRANTED way to get replication issues in your topology (lock, split, re-init, etc...).
Please use instead the 'application-level' clustering that you get out of the box with the Multi-Master Replication.
http://docs.oracle.com/cd/E20295_01/html/821-1217/index.html
http://docs.oracle.com/cd/E20295_01/html/821-1220/fhkry.html#scrolltoc
HTH,
Marco

Securing applications communications running in the same server

Hi everybody,
I want to share critical information between two applications (medical information about patients) using JMS queues, moreover due to this criticity i was planning to secure this communication using SSL. The problem is that one of the client applications, because of his architecture, have problems when accessing the JMS queues.
But I have to say that both applications will run in the same server (physical machine), knowing that, what kind of security problems could we encounter if, finnally we don't cypher the communication?
I guess that the danger is lower than if the two applications would run in different machines, wouldn't it?
Thanks!!!

hi,
add crossContext="true" in server.xml under tomcatx.x\conf\ in your <Context tag

CNR: Two cnr instances in the same server (lab environment)

Hello, we are trying to install two cnr 7.2 intances on the same server in order to replicate in lab the real environnment (failover local cluster) without deploying two servers.
I've seen on the installation guide that installing both a local and regional server on a single machine is supported, but what about two local servers working as a failover pair?
up to date, we've managed to install both installs, the dhcp servers are configured for using different interfaces and web gui are listening in different ports. scp ports have been changed (1234 and 4321 ) and, on dhcp-server expert configuration: failover-remote-port and failover-port are configured to be different (677 - 678 in one , and 678 - 677 in the other)
We can manage both servers from DHCP - failover configuration, as they show up and running, and even see logs... The other configs are
When trying to syncronize we get the error
"ChangeSet list is empty."
is this configuration supported?
best regards!

user10127912 wrote:
Hi,
We are planning to install second instance of Oracle 11gR2 in Linux server 2.6.39-400.21.1.el6uek.x86_64 x86_64. This is something we never haven done before. If you have such experience, please give us some insight.
The existing instance has all the standard ports:
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
Enterprise Manager Console HTTP Port (pterpdb02) = 1158
Enterprise Manager Agent Port (pterpdb02) = 3938
What ports should we select for second listener and enterprise manager? Is there anything else that we need to know before we install the second instance?If you want a second database instance, no additional installation is required - as long as you want to run the second instance at the same version as the the first. Just fire up dbca and create the second database. One installation of Oracle (one ORACLE_HOME) is capable of supporting many database instances, though the same may or may not be said of the hardware it is running on.
As already said, one listener is enough. One listener, running from one oracle home, using the default name of LISTENER, running on the defualt port of 1521, is quite capable of -- indeed, WAS DESIGNED TO, supporte multiple database instances of multiple versions running from multiple ORACLE_HOMEs.
One instance of dbcontrol/dbconsole will support only one database. If you do not use Grid Control (extra installation, extra license) you will need to use the emca utility or one of the options in the dbca utility to configure a seperate instance of dbcontrol for each database. Don't worry about the ports, the creation utility will take care of it and report what it does.

Server 2012 R2 DC and File Server on the same server

alexthefourth wrote:
what i plan on doing is running esxi as the hypervisor and running a vm with server 2012 r2 and another server with windows 7 due to a fax application not being able to run on server editions.
You can still run two Windows 2012R2 Servers on Esxi, just like Gary said. For 10 users, it's really not that big of a deal either way.

KOOLER (StarWind) wrote:You're breaking up the whole thing! Virtualize both DC and FS and live your long & happy life!https://technet.microsoft.com/de-de/library/virtual_active_directory_domain_controller_virtualizatio...http://community.spiceworks.com/topic/448752-server-2012-r2-virtual-file-server-best-practiceGood luck :)--is it okay to run a domain controller with dhcp, ad, and dns on the same server? this is mostly due to budget concerns for purchasing a second server 2012 license.
1 License covers two V servers doesn't it? +1

Any reason not to put Lync Edge server on the same server that runs Web Application Proxy?

We're currently running Lync 2010 standard server, without an edge server or reverse proxy. I'm working on migrating to lync 2013 standard server, and would like to add the edge functionality in the process. I have a Server 2012R2 in the dmz,
with the web application proxy role installed. I plan to use that to publish the lync web services. Is there any reason I shouldn't install the lync edge server on the same computer?

It just won't work well as everything will want to bind to port 443 (the reverse proxy and the edge services as well). On top of all that, it's just not supported. A new virtual server will save you hours upon hours of frustration and leave you
with a supported configuration.
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications

How to check if the requested server is the same server?

Hi,
I am building a request using URL connection. Before making a connection to the server I need to check if the URL requested server is same server. If it is same then I need to call locally Instead of making URL connection.
Please help me.
Thanks in advance.
Arthik
Edited by: TNKarthikBabu on Jun 29, 2009 3:07 PM

Check what methods the HttpServletRequest you provides.
Here is its API doc: [http://java.sun.com/javaee/5/docs/api/javax/servlet/http/HttpServletRequest.html].

Windows 2012. Assign RDS service Licensing Server on Standalone Server. Connect to the licensing server on the same server as RDS

I have installed Windows Server 2012 Standard. I wish to run this server as a standalone server using local users as the authentication for RDS and not part of a domain. I have my RDS licenses loaded in RDS licensing service and all license show up
in the Licensing Server. I get events telling me to connect to a licensing server and I find no configuration tool now to connect to the local licensing service. It will not let me connect to the licensing service on the same computer.

Hi Bill,
After referring to your post, we can understand that you are facing issue with licensing service for your RDS Server. As Ryan has provided great article for deploying RDSH server in workgroup mode you can refer that and also I would like you to check that have
you specify a license Server for RDSH server to use. You can perform this setting under
deployment properties of RD Licensing and specify the name of the server and in addition there is registry setting for this under below path.
Computer Configuration\Policies\Administrative Templates\Windows Components\Remote Desktop Services\Remote Desktop Session Host\Licensing
More information:
Specify a License Server for an RD Session Host Server to Use (For your reference)
http://technet.microsoft.com/en-us/library/cc770585.aspx
Hope it helps!
Thanks,
Dharmesh

If I have two accounts for the same server, how do I save both Passwords?

Is it possible to have the FireFox password save feature remember the passwords for two different accounts on the same server? For instance, I log into both my own account and my wife's account at Chase Bank for our credit cards, mine is a business card and hers is a personal card (of which I also have a card). I would like FF to remember both accounts and when I arrive at the server, FF to ask me which one I want to use.

Make sure that you not run Firefox in permanent Private Browsing mode.
* https://support.mozilla.com/kb/Private+Browsing
* You enter Private Browsing mode if you select: Firefox > Preferences > Privacy > History: Firefox will: "Never Remember History"
* To see all History and Cookie settings, choose: Firefox > Preferences > Privacy, choose the setting <b>Firefox will: Use custom settings for history</b>
* Deselect: [ ] "Permanent Private Browsing mode"

ACE always balances to the same server :o(

Dear colleagues:
I am new in this area so I followed examples from config guides. The requirement is to balance two real servers in a round-robin fashion but with source IP stickyness (more than one session from the same source IP must be directed to the same real server).
So I put all these commands on the ACE, but it always contacts the same real server although sessions come from two different source IPs:
rserver host SERVER_19
ip address 10.150.3.19
inservice
rserver host SERVER_20
ip address 10.150.3.20
inservice
serverfarm host REAL_SERVERS
probe HTTP_probe
rserver SERVER_19
   inservice
rserver SERVER_20
   inservice
sticky ip-netmask 255.255.255.255 address source WEB_SERVERS
timeout 720
serverfarm REAL_SERVERS
replicate sticky
timeout activeconns
policy-map type loadbalance first-match SLB_LOGIC
class class-default
   sticky-serverfarm WEB_SERVERS
class-map match-all VIP-30
2 match virtual-address 10.150.3.30 tcp eq www
policy-map multi-match CLIENT_VIPS
class VIP-30
   loadbalance vip inservice
   loadbalance policy SLB_LOGIC
   loadbalance vip icmp-reply active
Am I missing something? Your kind answers will be greatly appreciated
Rogelio Alvez
Argentina

Hello Gaurav:
Yes, I knew that roundrobin is the default predictor. And that is the algorithm I want to be executed. Regarding your queries:
1. At time of thest the customer just had two client laptops from which to try the connections. According to him, connections from both of these two laptops went to the same server (let´s call it server A).
2. I asked the customer to unplug that server (server A) from the switch, and the ACE -as expected- detected it as unavailable. Customer started the connections again from the 2 laptops, and now these connections were redirected to the only available server (server B).
I have not mentioned before that the ACE is actually a 4710 cluster, and working in bridging mode, but I do not think this could be a reason for the problem.
I also asked the customer (I am not in front of the customer installation itself, just remotely configuring the equipments) to try from lets say 3 or 4 different laptops at the same time.
I wanted basically to know that I was not doing anything wrong from a configuration viewpoint.
Something else that might be useful to know -as requested by customer, and configured by me via ACL- is that both real servers can be reached by their real IPs, because from time to time the customer wanst to reach them individually for maintenance purposes. That works OK too.
Please let me know if you want me to gather more information from the environment.
Thank you very much in advance.
Rogelio

How can i deploy two different versions of the same application on the same server??

I have two different versions of an application. One is a released version. And another version under development. I need to port this version of the application to the same server. I'm using the same classes and packages(except for some new ones). Is it sufficient if i change the name of my ear(application name). Or should i change my code also.

Hi
You can repackage the new versions of ear,jar and war with different names. I hope that should work well.
Cheers
-pradeep

Two clients in the same server--Script??

Hi Folks,
1.I have two clients in the same server say 100(used for dev) 120(used only for testing).I had developed a script in 100 which I want to test it in 120.Now how to move this script in 100 to 120.
2.How to use includes in scripts and what is the usage?
Thanks,
K.Kiran.

<b>INCLUDE: </b>Include other texts
With the command INCLUDE, you can include the contents of another text into your text. The text to be included exists separately from yours and is only copied at the time of the output formatting.With the INCLUDE command, you always get the most current version of the required text, since this is only read and inserted during the output formatting.
Syntax:
/: INCLUDE name [OBJECT o] [ID i] [LANGUAGE l] [PARAGRAPH p] [NEW-PARAGRAPH np]
The name of the text to be inserted must be specified and can have up to a maximum of 70 characters. If the text name contains blanks, then you must put it in quotes as a literal. It can also be specified via a symbol. All further parameters of the INCLUDE command are optional. If they are missing, SAPscript uses default values for them which are based on the respective call environment.
Examples:
/: INCLUDE MYTEXT
The text MYTEXT is included in the language of the calling text.
/: INCLUDE MYTEXT LANGUAGE E PARAGRAPH A1
The text with the name MYTEXT and the language E is included, regardless of in which language the calling text is created. The paragraph format A1 is valid as the standard paragraph for this call.
Optional specifications:
LANGUAGE If a language is not specified, the language of the calling text or the layout set is set for the text to be included. If a language is specified, the text is always loaded in this language, regardless of the language of the calling text.
PARAGRAPH The text to be included is formatted with the style allocated to it. With this parameter, the standard paragraph of this style can be redefined for the current call. All * paragraphs of the inserted text are then formatted with the paragraph specified here.
NEW-PARAGRAPH The first line of the included text has this format flag, provided it is not a command or comment line. If the optional entry PARAGRAPH (see above) is empty, all * paragraphs of the included text are formatted with the paragraph np specified with
NEW-PARAGRAPH.
OBJECT To specify a text completely, you must make further specifications regarding the text object. There are different rules and restrictions for this which depend on the object type of the calling text: All texts can be included in a layout set. If no object is entered here, TEXT is used (standard texts).With a documentation text (object DOKU), you can only include documentation texts. This object is assumed even if no object is specified in this environment. Only hypertext or documentation text can be included into a hypertext (object DSYS). If the OBJECT specification is missing, DSYS is set as a default value.
Only standard text (object TEXT), documentation text or hypertext can be included in any other type of text. The default object is TEXT if nothing is entered.
ID The text ID, which allows further text types within an object, is a further part of the text key. If the ID is not entered, the default Include ID from table TTXID is used for the calling text. If the specification is not in this table, the text ID of the calling text is used.
The ID together with the object are now the basis of a further consistency check:
All text IDs are allowed for a layout set.
Only documentation texts with the text IDs TX (general texts), UO (authorization objects), and documentation texts which have the same text ID as the calling documentation text may be included in documentation texts.
All DSYS texts may be included in DSYS texts, regardless of their ID. Documentation texts to be inserted may only have IDs TX and UO.
Standard texts with all the allowed text IDs, DSYS texts with all IDs, and documentation texts with Ids TX and UO may be included in the other types of texts.
Regards,
Santosh

I have two personal e-mail accounts and a general account that I have synced to my Mail app, but I keep getting emails sent to the non-personal e-mail because they're on the same server. How can I change that?

I have two personal e-mail accounts and a general account that I have synced to my Mail app, but I keep getting emails sent to the non-personal e-mail because they're on the same server. How can I change that?

The only ways I know of for email to get sent to an account are:
1. It was addressed to that account. Someone used that email address to send you the email.
2. It was forwarded to that account by the account to which it had been addressed. I am not aware of Mail having this feature but it is often a feature provided by your ISP that you can turn on by logging into your account via the Internet and setting it up. I assume you have not done this, though.
With several email addresses in the same Mail client, you have to be careful which one you are sending from. If you send from the wrong address, any replies will come back to that same address. I make this mistake all too often.

Two instances on the same server

I've already created one instance on 11g R2 database, but I was told to create another instance on the same server. Can I use the same listener for both instance? Will it cause any problem?
Thanks!
- Johnny

tanww888 wrote:
Thanks for all your responses. I have not dealt with two instances on the same server before. I'll take your advice to start with the same listener for both instances and see if it is causing any issue. My database server is a Oracle Sparc 5120 with plenty of memory and disk space. The second instance that I'm going to create will be much smaller than the first one.
Single or multiple listeners aren't really a factor for performance. Notice that even in Dan's remarks, none of his reasons for multiple listeners had anything to do with performance.
Question, is it easy to create/configure the second listener to point to the second instance? Just in case there is an issue using the same instance.
The listener doesn't "point to" the database - not in the sense you seem to think. It simply watches the ports it is configured to use (1521 by default) for connection requests from clients. When it gets a request it evaluates whether or not it knows about the service (instance) requested, and if it does it spawns a separate server processes to communicate between the client and the db instance, then is out of the way. The listener creates the connection but does not sustain it. You can stop a listener and all existing connection will continue because the listener has no part in maintaining them.
Multiple listeners would be configured by adding LISTENER sections to the listener.ora file. You might find it instructive to realize that if there is no listener.ora, a 'lsnrctl start' will cause a default named listener to start on the default port of 1521. By default, any db instances on that server will register themselves with the default listener on the default port. After this self-registration, the listener will know about the instance if/when it receives any connection requests for it. Let's switch from the telephone analogy to that of a desk clerk at a hotel. He comes to work and is handed a piece of paper that says "We have Tom, Dick, and Harry registered as guests" This would be analogous to the listener learning of instances via the SID_LIST section of the listener.ora file. Then Fred walks up and says "I'm Fred and I'm in room 238", so the clerk makes a note of that. This would be analogous to the instance registering itself to the listener. Either way, then someone walks up and says "Where would I find Tom (or Fred)". The clerks checks his lists and directs the person to the correct room. He doesn't escort the person around to Tom and act as a go-between for their conversation. And hotel management doesn't want to have to pay a separate clerk for each guest.
You might want to read my articles about TNS in general at edstevensdba.wordpress.com. I think they will help you get a clearer understanding.
Thanks,
- Johnny

Got a question on mail. We got two e-mail addresses, both different, but messages are picked up from the same server at Vodafone. Received at my iMac I want them to be splitted to two accounts, depending on each e-mail address. How to do this?

Got a question on mail. We got two e-mail addresses, both different, but messages are picked up from the same server at Vodafone. Received at my iMac I want them to be splitted to two accounts, depending on each e-mail address. How to do this?

Hello,
Could you please clarify you have two email addresses [email protected] and [email protected] each with it's own password and you want these delivered to differnt OS X user accounts or seperate folders within Mail?
mrtotes

Two Communication Server in the same Server ?

Similar Messages

Maybe you are looking for