Two questions re: X58 Eclipse SLI

Hi all -
two questions regarding my (admittedly older) X58 Eclipse SLI:
1.) When I built the system, I had two IDE DVD devices: one reader and one burner. I've since replaced the burner with a SATA burner but now I can't get Vista 64 to recognize the reader. I have the reader setup as 'Master' on the IDE bus and it does get identified when booting the system. Vista won't see it, though, even with the JMicron drivers installed.
2.) When I bought the board, I also bought an OCZ 1600 DDR3 kit (OCZ model# OCZ3P1600LV6GK). I FINALLY got the RAM stable at 1333MHz, but I've considered adding more RAM to the system. Am I likely to experience issues if all the RAM is not matched - especially considering I've had to customize the RAM voltage and timings?
any suggestions here would be greatly appreciated!
Mike

Quote from: PirateDog on 20-April-11, 06:31:10
It may be possibe that a firmware update is available from the device manufacturer that will make the drive compatible with Vista?
Possible, however I doubt that's the issue considering that the drive functioned normally prior to the removal of the 2nd (SLAVE) drive. To clarify, when both drives were attached to the PATA controller everything worked fine. When I went to a single drive, the OS no longer recognizes the MASTER device.

Similar Messages

X58 Eclipse Sli with CMP12GX3M3A1600C9 how to make it run stable in 1600Hz?

Hello ,
I m new here, so forgive me if i make a mistake somewhere !
So my specs are :
motherboard: X58 Eclipse Sli(bios ver:1.F0 model:MS-7520)
CPU:i7 950 @ 3,07 (stock)
GPU: 2x GTX470(msi)
PSU:Thermaltake 1200watt
HD:1xSSD , 1xWD@10000rpm
and here is my story:
I have been using TR3X6G1600C9(corsair ver8.1) with XMP enabled so in 1600Hz and everything were going sweet stable pc , then i decided to put something more on it another TR3X6G1600C9(corsair) this time came different ver2.5 with XMP profile off seems work fine , with XMP on blue screen-restart so i asked in corsair forum they show a .pdf from corsair which was saying that mixing modules even with same kind of memory there are posibilities it wont be compatible-work.
Today i just replaced the 2xTR3X6G1600C9 with CMP12GX3M3A1600C9(corsair) enabled the XMP profile , everything was looking good all 12gb were working , but after some time i got blue screen and restart :(, so i bet this has to do with options and propably i have to do more than to enable XMP profile in order to make it stable. So any suggetions ? Yes i m totally noob from knowledge in bios only i know is to enable XMP but i m looking forward to learn stuff from ya guys and considering that i might just lost about 230e in order to upgrade ram and i can't make to work 12gb stable in 1600hz i should of ask much earlier!

Quote from: IcUfu on 19-May-11, 02:54:22
Hello ,
I m new here, so forgive me if i make a mistake somewhere !
So my specs are :
motherboard: X58 Eclipse Sli(bios ver:1.F0 model:MS-7520)
CPU:i7 950 @ 3,07 (stock)
GPU: 2x GTX470(msi)
PSU:Thermaltake 1200watt
HD:1xSSD , 1xWD@10000rpm
and here is my story:
I have been using TR3X6G1600C9(corsair ver8.1)(http://www.corsair.com/memory/xms-classic/xms3-ddr3-memory/tr3x6g1600c9.html) with XMP enabled so in 1600Hz and everything were going sweet stable pc , then i decided to put something more on it another TR3X6G1600C9(corsair) this time came different ver2.5 with XMP profile off seems work fine , with XMP on blue screen-restart so i asked in corsair forum they show a .pdf from corsair which was saying that mixing modules even with same kind of memory there are posibilities it wont be compatible-work.
Today i just replaced the 2xTR3X6G1600C9 with CMP12GX3M3A1600C9(corsair)( http://www.corsair.com/memory/dominator/dominator/cmp12gx3m3a1600c9.html) enabled the XMP profile , everything was looking good all 12gb were working , but after some time i got blue screen and restart :(, so i bet this has to do with options and propably i have to do more than to enable XMP profile in order to make it stable. So any suggetions ? Yes i m totally noob from knowledge in bios only i know is to enable XMP but i m looking forward to learn stuff from ya guys and considering that i might just lost about 230e in order to upgrade ram and i can't make to work 12gb stable in 1600hz i should of ask much earlier!
What i have done so far ,with CMP12GX3M3A1600C9 http://www.corsair.com/memory/dominator/dominator/cmp12gx3m3a1600c9.html
turned off XMP , put manually :1.DRAM freq-1600Hz 2. CAS timings 9-9-9-24 3.DRAM command rate 2N 4. DRAM Voltage 1.65 it did't crass again so far but i am afraid about this DRAM Voktage 1.65 is it posible that i will destroy my CPU this way??? The rest options in bios are setted to optimal defaults should i change something else in order to protect my CPU?

MOVED: MSI X58 eclipse SLI CPU throttling problem

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=128074.0

Quote from: goofazoid on 03-October-09, 15:03:29
If you turn EIST off you should be able to put the multiplier to a specific number between 12 and 21 (or higher if you have an unlocked Extreme CPU) and that is where it will stay.
I believe that is exactly what i did, i disabled EIST, C1E and set multiplier to 21, however, when i run a stability test(Prime95 or Linx) it always drops the multiplier down from 21x to 20x.
It seems to me turbo mode is still working when it is supposed to be disabled when you set multiplier to 21(or maybe it is just simply won't allow x21 multiplier to be used at full load anyway, turbo mode on or off).
Quote
Very good point Jack. There you go ravescar & others, give that a try & see if it makes a difference. smile
I experimented a bit with Overspeed Protection enabled and disabled, however i did not notice any difference in this regard, the multiplier still drops to 20 on high load for me.
However this problem do not happen if i set multiplier to 20, it is only the 21 multiplier that have this issue.
This is on a MSI X58 Eclipse SLI Motherboard + i7 920 D0 stepping + 6gb GSKILL Trident 16000 CL9 RAM.
Quote
BTW. I've read of a couple of cases where DO stepping 920's getting 22x with Turbo enabled but I'll remain skeptical regarding the validity.
Maybe it is just earlier version of cpu-z mis-reporting multiplier?

MOVED: X58 Eclipse SLI temperatures

This topic has been moved to Intel Core I7 boards.
https://forum-en.msi.com/index.php?topic=122469.0

IF your IOH Temps are INSANELY HOT like mine (up to 110-127 C!!), there might be something wrong with your Heatsink (the giant two-sided one with the copper pipe). Those plastic pushpins don't seem to hold the heatsink firmly to the two chips (I'm not sure which one is the IOH yet). Anyway, I tried using pushpins from other boards and using arctic silver thermal paste - no difference. BIOS 1.1 - no difference.
Finally, I decided to get a little bold and try using some screws to literally screw the heatsink down thru the existing holes into the MB - WARNING do this at your own risk!! I found some screws that were the diameter of the 4 holes on the heatpipe from the leftover screws that came from my antec case. I cleaned off the old heatsink material (lots of elbow grease, or rubbing alcohol, q-tips and patience. I put everything together and now it makes a nice solid contact to the MB. Be careful not to overtorque - you basically want to fasten it down solid to ensure no movement.
Guess what? The IOH temps are better now !!
CPU 31C
Sys 47C
IOH 86-93C (93 using cooling settings in MSI Overclock tool; 84 using default cooling settings = much improvement from 110-127C!!!)
(If Sys is hotter than IOH, make sure you have the latest version of MSI Overclocking Center program from MSI's website).
MSI-7522 i7 920 (Eclipse x58)
OCZ 3x2GB Ram (NOT overclocked)
ASUS 4800HD PCIx
Maxtor 1TB Drive

X58 Eclipse Jmicron Raid

MSI x58 Eclipse SLI BIOS Version 1.2
Intel i7 920 2.66
12 gigs OCZ 1600 OCZ3G1600LV6GK
2x WD VR 150
3x WD 750 Caviar Black
Thermaltake W0116RU 750W PS
Lite-On 6x Blu-Ray 16x DVD-R iHES206-08
Thermaltake Speedo VI90001N2Z Case
Building a new system and have been pretty happy so far except I am unable to get into the JMicron raid utility to set up the Raid. The user manual says to press Ctrl-J to enter set up for the Jmicron controller but it does not work. Bios sees the 2 drives and I have their type set as Raid 0 and the Bios reflects that, but during post I am unable to access the Raid controller in order to configure the 2 drives.
The Intel utility is fine. I selected Ctrl-I during post and I was able to select my 3 750 and create the array. I just want to do the same with the 2 WD 150 Raptors. Am I just missing something?
Any suggestions??
Thanks

It means i am not having a problem loading the drivers in Windows. It is not a Windows issue. The problem is if you wish it install the OS on a RAID you must set the raid up first then when you install Windows you tell windows what drivers to us with that Raid array.
To summarize i need to know how to get into the Jmicron Raid Controller buring the bios post so i can set up the array.

Settings for OCZ3OB1600LV6GK on MSI Eclipse SLI (X58) and i7 @ 920??

Hello everybody!
Could anyone suggest me the right settings for the RAM (at 1600MHz), in order to pass memtest (in windows) wih no errors?
I've managed to setup the RAM at 1333 MHz without errors at all and my sytem stable. All the Dimms have been examined one by one and found healthy (via memtest in & out of windows). Thank you in advance!
Here are my computer specs:
MSI Eclipse SLI (MS-7520)
Intel(R) Core(TM) i7 920 @ 2.67 GHz + Noctua NH-U12P SE1366 CPU Cooler
XFX NVIDIA GeForce GTX 285 (1024 Mbytes - GDDR3)
OCZ DDR3 PC3-12800 /1600MHz /Value Series /Obsidian XTC Heatspreader /Core i7 Ready /2GB Module /6GB Triple Channel
WD2500AAKS
Corsair HX620W Modular Power Supply

Henry thank u for answering!
First image settings (in bios): 9-9-9-24 (1T), Memory Ratio 1333Mhz - Uncore Ratio 2666Mhz, DRAM Voltage -Auto (1.50V), Spead Spectrum Disasbled. PASSES MEMTEST
Second image settings (in Bios): 9-9-9-24 (1T), Memory Ratio 1600Mhz - Uncore Ratio 3200Mhz, DRAM Voltage 1.65V, Spead Spectrum Disasbled. FAILS MEMTEST
I have tried a lot of different timings to stabilize at 1600Mhz but no luck I tried also to icrease the QPI Voltage at 1.35V (as i was suggested by a friend) but i can't read anywhere the default voltage in order to increase it
The CPU-Z SPD tab 1st and 2nd image shows some sets of timings which are the same. They differ a lot than the manufacturer's settings (9-9-9-24 1.65v). Which of these should i use? Could you help me a little by being more specific?
p.s: Hope you can see the images as they are my first (pic) uploads!
(Click images to enlarge)
I made your images clickable.
-- Mark

New ECLIPSE SLI Build, but not POSTing

Hello MSI peeps,
Installed MB, CPU, CPU cooler, 1 stick of RAM, SSD, HD, PSU, 1 Video card and Optical drives, but cannot get it to POST.
I powered up and the MB is showing light blue indicators on installed components, but no video signal going to monitor.
I shut down, then connected DLED2 and powred up and DLED2 says CPU.ini, which means CPU error on POST, but is this really true? I have read allot of everyone's posts on this forum where all claim that DLED2 is faulty.
I am thinking that I may have plugged in too many drives and will disconnect the HD and optical drives to see if that may be the problem....should I also try to reset CMOS too?
Here's my rig....
Case: Coolermaster CM-830
Mainboard: MSI Eclipse SLI
CPU: Intel i7 975
CPU cooler: Thermalright ULTRA-120 Extreme
RAM: Two sets (12GB) of Corsair TR3X6G1600C7D Dominator 6GB PC3-12800 1600 MHz (2GB * 3)
Video Cards: EVGA Model GTX295 Co-op x 2
PSU: Enermax Model EGX1250EWT GALAXY EVO 1250W
Primary drive: Patriot Torqx 2.5-Inch 128 GB SATAII SSD - Model PFZ128GS25SSDR
Storage drive: Seagate Barracuda 500gb
Optical drives: Pioneer Blu-Ray DVD Burner Model BDR-203BKS / SAMSUNG DVD Burner Model SH-S223L
Thanks for your inputs!!!

Hey All,
Thanks for the help, but still no change....to save you having to read every thread, basically my build won't go to post.
DLED2 reads that it is CPU.ini and of course I questioned hte validity of the DLED2 reading as I have read other threads claiming that DLED2 is faulty.....so thanks to those who have replied, I have tried everything suggested, but the build still won't post....no beeps, no video signal, but the mobo and video card LEDs indicate no issue.
Is it RMA time or should I try something else? Should I just RMA the board or should I also RMA the CPU too?
Thanks for your help!
My build....
Case: Coolermaster CM-830
Mainboard: MSI Eclipse SLI
CPU: Intel i7 975
CPU cooler: Thermalright ULTRA-120 Extreme
RAM: Two sets (12GB) of Corsair TR3X6G1600C7D Dominator 6GB PC3-12800 1600 MHz (2GB * 3)
Video Cards: EVGA Model GTX295 Co-op x 2
PSU: Enermax Model EGX1250EWT GALAXY EVO 1250W
Primary drive: Patriot Torqx 2.5-Inch 128 GB SATAII SSD - Model PFZ128GS25SSDR
Storage drive: Seagate Barracuda 500gb
Optical drives: Pioneer Blu-Ray DVD Burner Model BDR-203BKS / SAMSUNG DVD Burner Model SH-S223L

Eclipse Sli, Leds on, No boot

Hi everybody,
I bought two days ago an Msi Eclipse for my new computer :
Mobo : Msi Eclipse Sli X58
Proc : I7 965 Extreme / Noctua NH-12 SE2
Ram : 3 * 2 Go Kingston Hyper X 1600Mhz
GC : ATI HD 4890 Vapor X
Power s. : Silencer 520 W
HD : Samsung SpinPoint 750 * 2 + 500 * 1
The problem :
When i switch on my PC leds are on and all fans work, but no signal on screen and Dled2 Off.
What i Tried :
Ram :
No ram
Only one
Corsair TwinX 1600
GC :
No GC
Fan :
All tower fans off
Nothing appened and the problem is still the same.
Regards,
Sky

Ok ,
So i successed :D and i'm still alive lol
I think it will be a little bit long to explain what i done in details so i resume :
I put the mobo on a table and used an air cleaner first.
Second, I put on the mobo only the cpu and the cpu fan, I made as you suggest me, clear cmos : the Dled2 worked but blocked on the DRAM.
Finaly I put the DDR3 only one slot and it didn't work , the post was still bloqued on the dram. I tried with an other old one , still bloqued, i put the three slots of the new one, it worked...
I don't know where was the real problem but if it can helps someone
Regards,
Sky

Random restarts with Eclipse SLI board

This is a copy from my post on the Vista forums havent gotten much help there.
Describe the problem in detail!
I just built a new system on December 22nd 2008. I do Tier 2 and 3 Helpdesk work so I can work my way around a system. I put the machine together installed Vista did all the updates got all the newest drivers. Basically since I have built the Machine it will just randomly restart. It will not display a BSOD, I have auto restart turned off, and it does not create an event in the event viewer. It is almost like someone touched the reset button.
When did the problem start?
December 22nd 2008 the day I built the machine.
What have you tried to fix it?
Tried several different BIOS setups. I have upgraed the bios, did all the windows updates, got all the newest drivers for video, audio, lan etc etc. Removed MSI Live Monitor, disabled green power in Bios, and removed overclocking center. Went through event viewer and corrected three of the four errors that was showing up. One error is the Kerebos one and I am not worried about that one. I have just run both Memtest86 and Memtest86+ and both of them stop responding about half way through the test.
What is the error message (of any)?
I have Vista set to not auto restart so I should see a BSOD but I get no message. I have had 4 restarts just today and none of them created a new MEMORY.DMP file or any type of event in the viewer.
I do get warnings about something called FLASH.SYS but I cannot seem to track down what this is.
What was the last thing you did before the problem started?
Built the machine.
What are your system specs?
Vista 64
MSI Eclipse SLI X58
12 Gigs Crucial ram matched to the MoBo using the crucial matching system on the crucial website. The MoBo supports up to 24 and I am using Vista 64bit.
Antec P190 Case (Dual power supplies for a total of 1.2 KW of power)
Intel Core I7 2.66
Creative Extreme Gamer Edition PCI E sound card
Mcaffee
BFG 260 GTX
Coolmaster V8 cooler (CPU under stress runs about 70f well below the max of 208f)
Do you have a screenshot?
Nope
My next step is to take out 6 gigs of RAM and see if the issue goes away.
Any suggestions?

Quote
12 Gigs Crucial ram matched to the MoBo using the crucial matching system on the crucial website.
Please provide a link to the Crucial Product site for your memory modules and make a screenshot of the CPU-Z "SPD" view.
Quote
My next step is to take out 6 gigs of RAM and see if the issue goes away.
Test one memory module only and see what happens. If things seem fine, add one more module and test again (and so on).

MSI Eclipse Sli and Asus 6950 Direct CU II problem

I’ve recently bought the Asus 6950 Direct CU II 2GB. After I installed it a weird buzzing sound started coming from around the area, where the big heat sink below the cpu socket sits. That only happened when the graphics card was on high profile and particularly when I was in any game.
About a month later my card stopped working properly so thinking it was its fault I used the warranty and got it replaced. However with the new card the system won’t even start. My monitor goes from “Please check signal cable” to “No signal” and apparently the system is not even moving past the bios checks.
The weird think is that when I use my old card (MSI R4870 1GB) the system seems to work properly!!! I tried the 6950 in two different systems and it seems to be working….
I’ve tried resetting the bios removing other devises to test the power supply etc., but nothing works, I can only think that something is wrong with the motherboard.
Any ideas on what might be wrong???
My system is:
MB: MSI Eclipse Sli
CPU: Core I7 920
PSU: TAGAN TG700-U88 PIPEROCK SERIES 700W
RAM: 3 x CORSAIR TR3X6G1600C9 Triple DDR3
HDD: WD Velociraptor 150GB for the OS

Thanks for the timely reply HU16E.
I don't have another psu available right now but I will in 3 days so I will try that.
On the other hand I have mine working as a single rail from the day I bought it (turbo mode switch on the psu), but i am not sure how this can be connected.
Also while I was playing around with the system it started up, only once, with the 6950, and that happened with everything connected so I still can't figure what the hell is happening!!!! I am thinking that something on the pcie port is wrong so i tried on the other ports too, yet nothing happened.
I am still leaning towards the motherboard but any other ideas would be welcomed.

PC shuts down or reboots spontaneously (MSI Eclipse SLI)

Starting a new thread to avoid totally hijacking another thread talking about almost the same symptoms here.
My original post:
Quote from: Smoke on 05-April-09, 12:43:21
I get this same situation.. except the event viewer doesnt state anything.
The system is not bluescreening.. it just hardware powers down and reboots.
I get the same message as the original poster as well, it is very annoying as it often happens in the middle of doing something.
I wonder if it could be thermal related to the high IOH temps on the board (often 80-85C, but not sure what happens to them in the middle of playing a game)? Is there any way to log the temperatures to a file so I can check what they were at the time of the crash?
I get this issue whether I change the default bios settings or not. Ive got a 920 on my eclipse board, my CPU temps are below 30C under load. System temp is about 27C.
What can I do?
The following replies:
Quote from: AaronYuri on 05-April-09, 12:56:57
That's way too high, even for 100% load. Reinstall the heatsink.
Quote from: Smoke on 05-April-09, 20:46:53
It is? I found another thread on this forum where it was mentioned that intel and msi said the IOH runs hot and to expect temps up to 100C. How do I go about changing the manufacturers heatsink on a board? Ive never done that before and cant find any procedural help thru google...
Ive been able to replicate the issue by running ram up to high usage. When I get above 98% ram allocation, I spontaneously reboot. So It could be a ram issue as well. Of would that be something possible IOH related as well?
Quote from: NovJoe on 05-April-09, 23:37:33
smoke,
Can you list out your full system spec and PSU spec?
System Spec:
Core i7 920 w/ TRUE 120
MSI eclipse SLI (bios 1.4)
6x 1gb corsair 1866mhz rated ram sticks (TR3X3G1866C9DF)
1500w thermaltake psu
galaxy gtx295 in the primary x16 pci-e slot
MSI eclipse soundcard in the 1st pci-e x1 slot
4x 1tb samsung 'UJ' hdd (raid 5)
O/S (= old winxp 32 bit until I get hold of a 64 bit os) running on 128gb PQI SSD
lg bluray burner
All the drives are sata2 and running on the ICHIOR ports.
For bios settings Ive got the optimised defaults with spread spectrum off and turbo boost on. Once its table then I will OC, but for now its not stable at the baseline yet.
Temp info:
IOH temps are as I said, around 80 at startup but rise to at least 87 under load, but not really much further that Ive seen.
CPU temps are very low with the dual-fan TRUE 120 heatsink. I havet seen it go above 35C with a reasonably heavy processing load. Usually sits about 0-2C above ambient at most when idle.
System temps get to about 40 under load, or around 27-35 under regular usage, but Im not quite sure what thats measuring the temp of on the board.
The issue is very frustrating but somewhat intermittent - I can go two days without a crash but then get several in a row. I wasnt previously paying attention to my usage at the time tho so I dont remember what I was doing when it crashed that I wasnt doing when it was fine. I have been able to replicate the crash/reboot/shutdown symptom by running multiple memory intensive apps and loading the ram up to just on the 2.99gb mark (the most winxp 32 bit will 'see') and it goes down. No blue screen though.. its a hardware issue not software I am pretty sure.
[edit] Updated the ram part number to be correct.

ok, should I label this possibly as solved?
I followed MSI's advice and checked through on drivers. Ive got totally up to date drivers, but nvidia just put out a .5 driver update (i mean, its increased the driver version by .50) and so I updated to that. I still got a sft reboot on testing, so no real joy.
THEN, I did the big change MSI asked me to do - Ive successfully brought my system up to bios 1.5B3 and pow, massive improvements all round!
Intelburntest runs perfectly now, no crash, no reboot, no errors of any kind. All residuals match. No memory errors. Memtest86 2.11 runs smooth as silk without errors either. PCmark runs out a basic benchmark of almost 19000 (about 3000, or 18.75%, more than the std core i7 920 benchmark without OC'ing) and looks great. Couldnt get that to run previously either.
The previous methods which 100% of the time would replicate the soft reboot of the system now no longer do so at all (i.e. 0% of the time yet) and for that matter I have not been able to get the box to fall over AT ALL since the new bios.
I have the same temps on cpu/ioh/system as I did previously. I recall for the same clock speed the cpu was putting out something well under 20 gigaflops... now its a solid 28. I didnt even realise that was a symptom of anything wrong, else the bios does some amazing extras.
I should note, Im only now using the 'optimised defaults' setting thru the bios. No overclock at all yet.
I'd love to know what MSI changed from 1.4 to 1.5B3, but whatever it was.. it does appear to have solved my issues. I wont say that conclusively just yet, but I cant bring the system to a crash no matter what I try now where it was rather easy to blow it over with a quiet whistle before.
Other things Ive noted is that the page file now seems to be actively utilised. Ive pushed it at load up to almost 3gb where before the bios update I was struggling to see 400mb used. Not sure if that was part of it, but if you get simiar issues go straight to MSI and see about getting hold of the 1.5B3 bios or later.
To quickly address the recent replies:
1) Ive got to agree with HU16E with my ram. I have no trouble running at the 1333 JDEC spec. And I feel very positive about now being able to achieve the XMP spec with this new bios.
2) Thanks for the link Aaron. I did end up using the USB flash method from this forum. Worked perfectly. Chalk up another success story!
3) I did try to swap out the ssd last night, but the system kept soft rebooting while installing the OS on the spin drive. SO I gave up. Seems the ssd isnt a drawback under the new bios tho (assuming it even was a cause earlier).
4) Ive DL'ed the x64 windows 7 beta and I'll likely as not have a shot installing that and refitting the extra 3gb ram back into the system. I'll let you know how it goes. Theoretically 6x1gb sticks should be as much as 15-20% faster than 3x 2gb sticks (and were about that much cheaper for me at time of purchase) but I'll run some benchmarks now that the benchmarks work and let you know the differences in case anyone wants to build their box the same way.
Conclusion:
I'll stress the system over a bit for the next few days without overclocking and I'll see if I can bring the system to reboot like it did previously through high usage, and if I cant I'll change the thread to solved and write out a proper solution post for the problem, symptoms and solution.
Id like to take the opportunity to say thanks to all the guys who've given me help and advice. Youve all been really great. Thanks a bundle! I owe you one

Eclipse SLI CPU fan always on max

Hello i got a problem with my Eclipse SLI. It's look like the CPU smart fan function don't work and the CPU fan is on max all the time.
My bios temp's goes from 32-40 C. I have used a lot of different bios versions. 1.4 - 1.7 - 1.9 - 1.a none of those could fix it.
Eclipse SLI
Intel i7 920 - standard clock
hope anyone got a good answer to my question. thx

Quote from: mibsen on 10-December-09, 05:40:05
Hello i got a problem with my Eclipse SLI. It's look like the CPU smart fan function don't work and the CPU fan is on max all the time.
They have a switch for "always maximum cooling" and "temperature controlled speed". Check your CPU fan - it may help to read the CPU installation instructions as they show where the switch is. I would guess that you have it in the wrong position, so your BIOS can't do anything...
Screet

Eclipse sli full board chipset water blocks?

Hi, I'm new to the these forums, but not a new MSI customer. I've had my eclipse sli since march '09 and was running everything @ stock. A couple of months ago a finally got around to OC'ing and noticed my IOH temps idling between 95-100c and 105-110c under load. I have since set everything back to stock and started searching for solutions, which led me to this thread. I have done the mod( HR-05 on IOH and I cut the heatsink for the ICH, I trust MSI boards.) and am pleased to report that my new IOH temps are 49-51c idle and 53-55c load. The strange thing is that my board seems to be clocking better because now with the stock heatsink I'm @ 3.5 with 1.26v stable whereas before the mod I was @ 1.3v stable on a custom loop. Which leads me to a question, sorry for being long winded and I'm not even sure if this is the right thread to ask it in but, Seeing that my lower IOH temps have given me the potential for a better clock I would like to add the IOH and ICH into the new loop I'm trying to put together, but I've looking all over for a full chipset waterblock for my eclipse sli and can't find any. Do they exist? Are they in production? or Are there any alternatives? Suggestions?

prymal, rename the title to suit your needs.
>> Posting Guide <<
I'll split and move this one to OC & Modding Corner.

Eclipse SLI slow install of Vista 64 and no bootable raid 0 volume

I've been trying to install Vista 64 on the MSI Eclipse SLI mobo with 2x Seagate 1.5TB hdd in raid 0. Can someone please help me?
I have the following:
1) Onboard ATA Devices set for [RAID]
2) Use ctl-i to create a raid volume [RAID0] - the volume reads as not bootable
3) Vista 64 install takes a long long time and does not recognize the disk volumes even with the ICH10R SATA RAID driver.
MSI Eclipse SLI mobo BIOS v1.8
OCZ DDR3 1600 mem
i7 950

Double and triple checked both the printed manual and the downloadable 7520v1.0 manual and found nothing indicating how to get the RAID 0 volume to become bootable.
I've tried configuring RAID in two ways:
1) Setting On-Chip ATA Device to [RAID]
Creating a RAID0 Volume - Not bootable shows
- Raid volume was created but was not seen during vista 64 install as valid drives, even after driver was installed.
2) Setting On-Chip ATA Device to [AHCI]
Installing the Intel Matrix Storage Manager Driver
- Vista 64 install was good but Intel Matrix Storage Manager did not have the action for making an existing device into raid.
I could however, make the RAID0 partition size smaller (1500TB) and that would allow the drives to show as bootable. There may be a bug with the Intel ATA Driver for drive size or a bug with the Intel RAID Utility (ctl-i).

Phase power on x58 Plat-SLi and Pro-E

Quick question on "how much" Phase power do each of these x58 board have (6 , 8 , 10 , etc) .....
x58 Platinum SLi - ?
and
x58 Pro-E - ?
I would imagine (or hope) atleast 8 on both .
Tia

Quote from: Henry on 27-August-09, 05:19:35
Is this what you are asking about?
5-phase DrMOS Power Design and APS(Active Phase Switching)
Yup , thx !

Two questions re: X58 Eclipse SLI

Similar Messages

Maybe you are looking for