Two WiFi Networks with Time Capsule

After installing TC (attached to an existing router), I seem to have two WiFi networks. is this normal? what should I do?

Thanks for the clarification. 
In general, unless you really need two wireless networks, it is a good idea to turn the wireless function off on one of your routers to reduce the chances of wireless interference that might occur between them.
If you notice no problems running two networks, you can leave both "on" if you want. In the future, if you notice diminished wireless performance, you probably will need to turn off the wireless function on one of your routers.

Similar Messages

  • I'm trying to extend my wifi network with time capsule but it can't find the existing wifi network

    I'm trying to extend my wifi network with time capsule but it can't find the existing BT wifi network even though it is there with a good signal strength. The Time Capsule is connected to a Netgear router via ethernet.

    You will need to start over on the setup of the Time Capsule as follows:
    Disconnect any Ethernet cables that might be connected to the Time Capsule, but leave it powered on
    Hold in the reset button on the back of the Time Capsule for 8-10 seconds and release. The reset button is located next to the AC power socket.
    Allow a full minute for the Time Capsule to restart to a slow, blinking amber light
    Connect the Ethernet cable from a LAN <--> port on the Netgear to the WAN "O" port on the Time Capsule.  The Ethernet cable must remain connected at all times.
    Click the WiFi icon at the top of the Mac's screen
    Look for a setting of New AirPort Base Station
    Click on Time Capsule
    The example below shows an AirPort Express. You will see Time Capsule on your screen.
    That will get the setup wizard going. It will take a minute to analyze the settings, then display a screen that looks like this, except you will see a picture of the Time Capsule
    Network Name..........Type in the exact name that the Netgear wireless is using
    Base Station.............Type in a name that you want to call the Time Capsule.  Use something short and simple. Mine is TC, for example
    Password..................Type in the exact password that the Netgear wireless requires
    Verify.........................Verify the Password again
    Click Next
    The setup wizard will configure everything for you automatically.  When you see the message of Setup Complete, click Done.
    That's it.  Now you have one big "extended" network.  Technically, this is called a "roaming" network.

  • How can i extend a wireless network with time capsule

    How can i extend an existing wifi verizon wireless network with time capsule? the router is connected on the bottom floor. want to boost the signal to a home office on the top floor, four flights up. connect time capsule via ethernet cable to iMac on 4th floor? Do I have to start a second wifi network or can I set it to just boost the one I have? thank you

    How can i extend an existing wifi verizon wireless network with time capsule?
    It all depends on what you mean by "extend".
    If you plan to "extend" by connecting the Time Capsule to the Verizon router using a wired Ethernet cable, this can be accomplished.
    If you were hoping to connect the Time Capsule to the Verizon router using wireless only, unfortunately the Time Capsule and Verizon products are not compatible for that purpose.
    Check with Verizon to see if they offer an "extender" or "repeater" that could be located very close to the Time Capsule.
    This would provide both more wireless coverage and also allow you to connect the Time Capsule using an Ethernet cable from the "extender" or "repeater".

  • How can I set up a guest WiFi network using Time Capsule and Airport Express extension?

    How can I set up a guest WiFi network using Time Capsule and Airport Express extension?

    Sorry, but it is not possible to "extend" the Guest Network using either wireless or an Ethernet connection.

  • Devices (iPad, iPhone) no longer can maintain wifi connectivity with time capsule

    My iPad and iPhone can no longer maintain wifi connectivity with time capsule.   Time capsule has connectivity to internet via Macbook, but not other devices.  This started after upgrade of devices to s/w 6.0.  Does anyone know if that could impact connectivity?

    Yes, this is often reported with iOS 6.. there are definitely more wireless problems.
    I recommend you reset the TC in the following ways.
    1. Change all names to SMB type.. ie short, no spaces and pure alphanumeric.. that includes the TC itself, wireless and hard disk. I recommend a different name for 5ghz so you can force clients to that band without auto voodoo affecting it.
    2. Use WPA2 Personal security only.. 8-12 character pure alphanumeric passkey.
    3. Lock the wireless channels.. particularly for 2.4ghz.. pick one of the channels, out of 1, 6, 11 as these are the only ones that do not overlap.. test each in turn for the best and most stable. TC should pick the best itself but that is voodoo and I am preferring to run the system without black arts.

  • Problems wirelessly extending 5Ghz network with Time Capsule

    Summary:
    My Time Capsule wirelessly extends a 5Ghz "n" network provided by my Airport Extreme, but the Time Capsule frequently fails and stops providing Internet access to connected computers. I'm not sure if the problem is with the Time Capsule or with the Airport Extreme it's connecting to.
    Setup:
    Airport Extreme (dual band) connected to cable modem. It provides a 5Ghz "n" network and a 2.5Ghz "b-g-n" network. This is in the bedroom.
    Time Capsule (non-dual band) joins the 5Ghz network and extends it. This is in the office, maybe 40 feet away, line-of-sight. There is a laser printer connected to the Time Capsule via ethernet.
    My MacBook is set to join the 5 Ghz network, and since it's in the office, it ends up joining via the Time Capsule. This is the desired behavior, as connecting through the Time Capsule seems to result in the fastest possible backup speed.
    There are no wireless devices, such as cordless phones, in the house. The microwave is NOT in use when the problems arise.
    *The Problem:*
    Frequently, the MacBook loses its Internet connection, though it is still connected to the 5Ghz network through the Time Capsule. When this happens, it can only see the Time Capsule it's connected through (and other devices that are connected to it) but no other devices on the network.
    When this happens, other devices that are connecting to the 5Ghz network through the Airport Extreme can no longer see the Time Capsule or any devices connected to it, such as the laser printer or my MacBook. This includes the living room computer, which has never been able to complete a backup due to this problem.
    The Time Capsule's and the Airport Extreme's indicator lights both stay green.
    If I change the Macbook's connection to the 2.5Ghz network, it can see the devices connected to the Airport Extreme, but can no longer reach the Time Capsule.
    *Unsuccessful Solutions:*
    This was happening in a previous incarnation of the network, when I had a non-dual band Airport Extreme providing the main network, the Time Capsule connected via 5Ghz, and an Airport Express connected via ethernet to the Time Capsule to provide a b-g network.
    I replaced the Airport Extreme with a new dual-band unit to simplify the setup, but it did not solve the problem.
    Since the Time Capsule seemed to be the weak link in the network, I reported the problem and got the unit replaced, but the problem still persists.
    I've reset both the Airport Extreme and the Time Capsule to their factory settings numerous times, and set them up again from scratch (no imported settings). I've gone in and made sure that there were no WDS settings leftover from the earlier configuration, as the 5Ghz network does not need it to extend itself.
    *Plea for help:*
    Is anyone else experiencing a similar problem?

    Update
    The other day, I modified the setup so that the Time Capsule doesn't extend the wireless network wirelessly, only through Ethernet (so the attached printer will work, but the computers will connect directly to the AEBS. The Time Capsule stayed connected long enough for me to do a full backup (125GB) from the downstairs computer.
    I thought I had it "solved" (though extending the 5Ghz network would be preferable so the office computers can have faster backup speeds.)
    But yesterday, I went to print to the Ethernet-attached printer, and it got only one page out before it disappeared off the network again, and the print job failed. I noticed it did it again, today.
    So the problem is not tied to wirelessly extending the network.

  • IPad2 in network with Time Capsule

    will i be able to use the time capsule for a iPad as a external memory and transfer file from one to the other?

    No, the iPad only connects to the internet sharing option of your network router (Time Capsule) through wifi. All other features of your router can't be accessed by your iPad. I have both also, so it would be nice. Try making that suggestion to Apple in the support section of the website. Who knows? We might get lucky. If this answer is satisfactory, please consider marking it as answering your question.
    Thanks

  • Creating wireless network with Time Capsule

    hi, I just have couple of questions before installing the time capsule;
    so far I have been using cable DSL modem, so my question is - is it possible to set time capsule as a wireless router, or does time capsule still have to be connected with DSL modem and then act wiresly with iMac?
    I was thinking if i could replace cable DSL modem with time capsule
    thank you

    The Time Capsule has to be connected to your DSL modem. Otherwise you won't be able to connect to internet.

  • Using the Network Three Wifi Dongle with Time-capsule

    Hi folks, i have just joined the forum today but have been an apple user for 2 years now. I do not use a router to get on the inter as I have recently purchased the 3 WiFi Dongle (mifi) and just wirelessly connect my ipad, iphone and macbook pro to it. My question is can I connect my macbook pro to my dongle and also to time-capsule wirelessly at the same time or is it only 1 device at a time?
    Also is there a way I can connect my USB wifi Dongle to my time-capsule and just have everything connecting to my Time-capsule?
    Any information on this would be greatly appreciated.
    Thanks
    Dave

    Welcome to the discussion area, harperdg33!
    You might want to take a look a device this this USB Broadband Adapter to provide an ethernet signal to your Time Capsule, which in turn could act as the wireless router for your network.
    The key element with any adapter like this is to verify that it supports your particular service, so you may need to do some checking about this.

  • Troubling extending wireless network with Time Capsule and Airport Extreme

    I am trying to set up and extend a wireless network in my house, but it’s not working right. I have two Airport/Capsule units in the house:
    2TB Time Capsule (Dual-Band II)
    1 Airport Extreme (Dual Band)
    I have the Verizon Fios router as my gateway to the internet, and also as my DHCP server. I have also tested the ethernet ports in my house to verify that they work, and that I can get a DHCP-issued IP address.
    Now, my Verizon router has WiFI, and it’s still on. I am not using it though except to troubleshoot. So far as I understand, this should not cause a problem.
    Base station setup
    So I setup the TC to Create A New Wireless Network, on the ethernet network it’s on (Dlink switch plugged into Verizon router). I set it up in Bridge Mode (as opposed to having it dole out IPs, since the Verizon router does this already). The TC gets a valid IP, and my wireless device connect to it without a problem. I have checked “Allow this network to be expanded” under Wireless settings.
    Extended station setup
    The AE Dual-Band is plugged into the Ethernet, and is reset to Factory Settings. I name it “Airport Extreme 2” and I chose “I want Airport Extreme to join my current network.” The other two options are: “I want to create a new wireless network” and “I want to replace and existing base station or wireless router with Airport Extreme.”
    I chose to “join,” I select “I want to connect Airport Extreme to my network using Ethernet to extend my existing wireless network.” The other options are to disable wireless entirely, or to “wirelessly join my current network.” On the next page it asks me to select the device or network that the Airport Extreme will connect to using the Ethernet. I set it to the Time Capsule.
    Results:
    Access near the Airport Extreme 2 is incredibly slow. Speedtest shows I am getting less than 1Mbps. Worse yet, my mail client won’t connect. It just times out.
    What I had hoped was that the AE would connect via Ethernet to the network, and just bring the wireless network to the other side of the house. Instead it almost seems as though it is just re-amplifying the TC’s signal. Otherwise, why is performance so bad?
    Thanks to anyone with some insight here!

    Hello Kennuff. Welcome to the Apple Discussions!
    Since you have the ability to connect all of the routers by Ethernet, there is no need to configure the Time Capsule (TC) & 802.11n AirPort Extreme Base Station (AEBSn) for a dynamic WDS (aka, extending a network). This option is only when the routers do NOT have an Ethernet connection between them.
    Instead, you want to configure the TC & AEBSn in a "roaming" network. I suggest starting by performing either a "hard" or "factory default" reset on both.
    Next be sure that both the TC & AEBSn are on the same Ethernet subnet coming from the Verizon-supplied router.
    Configure the TC & AEBSn as follows:
    AirPort Utility > Select the TC or AEBSn > Manual Setup > AirPort > Wireless
    o Wireless Mode = Create a wireless network
    o Allow this network to be extended: <not checked>
    o Radio Mode: <leave the default or if you require a specific mode make sure both routers are configured the same>
    o Wireless Security: <configure both routers the same>
    AirPort Utility > Select the TC or AEBSn > Manual Setup > Internet > Internet Connection
    o Connection Sharing = Off (Bridge Mode)

  • Extend FiOS wireless network with Time Capsule

    I have a FiOS wifi router and a 1TB TC (with latest firmware 7.6.3). I'd like to extend the wireless network to cover some dead zones. I've run ethernet from the LAN port on the router to the WAN port on the Time Capsule, and it's getting an IP and internet connectivity. However, when I follow the Apple instructions to extend a wireless network, I get the warning error "unable to extend network" and the flashing orange light. I've confirmed the SSID and password are correct and match the FiOS SSID and password, and I've confirmed that the TC is in bridge mode. I've also logged into the FiOS router and confirmed it's assigning IPs to the wired and wireless componets of the TC, and recognizes the wireless is in bridge mode. Any suggestions?
    I've got it working currently as a separate SSID, but it's just a pain to have to jump from weak-network1 to TC-network2 whenever I'm in a dead zone. Thanks in advance!

    Check to make sure that you have the TC configured to.....
    Create a wireless network  (not "extend".....as that is only used for wireless extension and you are using Ethernet)
    Use the exact same wireless network name (SSID) as the FIOS router
    Use the exact same type of wireless security that the FIOS router is using (Make sure that this is not WEP)  It should be WPA2 Personal or WPA/WPA2 Personal.
    Same wireless password as the FIOS
    Bridge Mode configuration
    Unless everything matches up correctly, you will have two separate networks that require two separate log ons.
    Configured correctly, you will have a "roaming" network. Your Mac will automatically switch over to the wireless access point with the best signal quality as it moves from one area to another.

  • Slow network with Time Capsule

    Hi There!
    We have a network at home consisting of a Time Capsule (to provide wireless to the house as well as to hold all of our iTunes content and use as a file server), two Mac Pro towers, a MacBook Pro, an iMac, and two Windows-based notebooks, and an Apple TV. We are NOT using the Time Capsule for backup.
    The problem we're having is that the network is incredibly slow. Trying to copy a large file over the network can take hours when it should only take minutes. And we can't stream shows/movies in iTunes from the Time Capsule because it pauses every one or two seconds to catch up. We also have business grade cable modem service but we can't do iChat videoconferencing without the audio/video completely dropping.
    We tried purchasing an Airport Express to extend the range of the signal (and even purchased a second one!) but those didn't help, either. The firmware on all devices it up-to-date. And the network is closed (no one is leeching).
    Are there any tools, either built in to OS X or another source, that can help us diagnose what's wrong with our network? What other things can we try to diagnose the slow network?
    Thanks!

    First of all, be aware that the more devices you connect to a wireless network, the slower it goes. In addition, if you have devices that only work at B or G speeds, all devices on the network slow down to the slowest device.
    For example, when you have a 300mbps N device and a 11mbps B device connected to the same network, they'll both go at a maximum speed of 5.5mbps. You are limited to 11mbps because of the B device and then further limited to 5.5mbps because there are two devices sharing the total (11mbps) bandwidth.
    As far as testing out your current connection, try these:
    1. On a mac, you can hold down Option and click on the airport/wireless icon. This will show transmit rate and other information. The maximum transmit rate for N devices is 270, G: 54, B: 11. If the transmit rate is very low, this indicates a poor wireless signal
    2. Change the wireless channel used by your time capsule to something else. Try them all to see what gives you the best wireless signal
    3. In the airport utility, select the time capsule, go to manual setup, go to advanced, click on Logs and Statistics, then click Wireless Clients. This shows the transfer rate, noise, and signal for each device connected to the time capsule.
    4. Download iStumbler. This mac application will show other wireless networks in the area and what channel they're using. It is typically not good to set your network to use the same channel as others in your area.
    5. Download some sort of application that shows transfer speeds (like iStat Pro). Test transferring large files between computers to see how fast it goes with different setups.
    There's a few things you can do to improve wireless performance when bogged down with too many devices:
    1. Turn off any wireless devices not in use. If it's on, it's using bandwidth space even though it's not transferring data.
    2. Use multiple routers or a dual-band router to create separate networks. For example, you can make the time capsule make a 802.11N-Only network which will only the new N devices will connect to. Plug an express into it and make it create another network (G-only or B/G-only). Keep plugging in additional routers and make new networks as needed.
    3. Replace older B/G devices with N devices if possible.

  • Extend wireless network with Time Capsule

    I have a dual band Time Capsule in a two story house. The TC is upstairs, and I have an Airport Express downstairs to extend the wireless network. However, the speed is very slow downstairs. I have recently wired the downstairs with ethernet cable, and would like to use a wired wireless repeater (bridge) to get a better signal downstairs. What hardware should I use?

    I have a similar but slightly different issue/question. I didn't know whether to start a new post but I will try here first. I'm not able to set up a 5GHz roaming network.
    I am a self employed songwriter and need 5GHz speed for numerous devices that stream video and music (computers, DirecTv, Tivos, AppleTVs etc.). All these have both wireless cards and Ethernet cables connected for backup. I need the 2GHz radio only for iPhones or guests. I have ATT DSL with 5 static IP addresses. The first is assigned to TCdual and "shared". My older "L" shaped home is tuff on wireless signals (plaster walls etc). Since I've had a lot of trouble with WDS and wireless connections, years ago, I ran Ethernet to every network device as backup, including an Ethernet connected Airport Express, with wireless turned off, I dedicated exclusively to Remote Tunes. It's been working the past few months (knock on wood). But I need to extend TCdual's 5GHz network with roaming. Here's what I've tried without success.
    I placed a 2nd Airport with 5GHz (the model before TC dual) in the room TC's 5GHz will not reach and connected it to TC via ethernet. Using Airport Utility, I tried to "extend" TC's 5GHz network. No luck. AU will only extend TC's default network, which is 2GHz. Very frustrating. So... the only way to get 5GHz in this room is to create a 2nd 5GHz network on Airport #2. Even using the same network name does not create roaming. Whenever I move MBP from this room, I lose Airport#2's 5GHz network and every WAN/LAN connection. I have to reconnect to TC's 5GHz network, every other WAN/LAN device, resume downloads, iChats etc. and start again. VERY frustrating. I think I must be missing something. Am I really forced to choose between speed or roaming. Can't I set up a 5GHz roaming network and have both?

  • Wifi issues with time capsule 3tb

    why does my wifi drop all the time, even though i have a state of the art $300 time capsule 3TB device.?

    If you have the latest AC model TC, please ring apple support and let them know.. your issue is repeated here over and over.
    I do recommend you have a few settings you work through but they may not fix it.
    1. Use all short names.. not long names with spaces and non-alphanumeric characters.
    2. For testing purposes set different names to the two bands, eg TC24ghz and TC5ghz.
    3. Set the channels yourself. This is not especially effective for 5ghz but may help with 2.4ghz
    4. Never use any security but wpa2 personal with a decent password.. pure alphanumeric.
    5. On the computers, make sure you set ipv6 to link-local not automatic.

  • I would like to extend my network with time capsule

    I have and airport extreme. I just bought a time capsule. I would like to keep the airport connected to the modem and use the time capsule to extend my network range and backup. The reason I want to set up my network this way is so I can "hide" the time capsule in another area of the house. Just in case of theft. I would rather have my back-up not located on my desk with all of my other equipment.
    When I was setting up the time capsule, it looked like it was doing exactly what I wanted it to do. Then it got to the last step, restarting. The device restarted, the green light came on, but it never showed up in the airport utility dock again. I had to reset it and start over. I ended up setting it up off network and connecting my computer with an ethernet wire and doing my back-up. Now, I have to get it set up wirelessly today. Otherwise, I just bought a very expensive hard drive and would not get the benefit of the wireless back-up.
    The guy at the store said this should be easy and it appeared like it was easy, but, something just isn't right.
    Any suggestions? Thank you

    In order for the Time Capsule to "extend a wireless network", the AirPort Extreme must first be configured to "Allow this network to be extended".
    Did you remember to enable that option on the AirPort Extreme before you tried to configure the Time Capsule to "extend"?
    Check your settings on the AirPort Extreme as follows:
    Open AirPort Utility, select the AirPort Extreme and click Manual Setup
    Click the Wireless tab just below the row of icons
    Make sure that you have a check mark entered in the box next to "Allow this network to be extended"
    Update to save settings on the AirPort Extreme
    Then, configure the Time Capsule to "extend a wireless network"
    Post back if you need more tips on this.

Maybe you are looking for